Questions about waveform processing

Hello,
   I have a waverform from a 2 channel scope.  I would like to be able to measure the time from the rising edge of channel 1 to the "presence" of a sine wave on channel 2.  Is there a easy way to do this in Labview?
Regards,
Kaspar   
Regards,
Kaspar

Kaspar,
How easy it is may depend on how well you can define the two points: The rising edge and the "presence" of the sine wave. Once you have those two points, simply subtract the array indices and multiply by dt. If you want to interpolate or if the signals are noisy and the definitions of the two points are not clear, then things may be difficult.
Lynn

Similar Messages

  • Question about signal processing

    hi
    at which location i should post the question about sigmal processing toolkit???
    plz inform me,,,,

    That sounds like a LabVIEW question to me.  This LabVIEW board seems appropriate.
    There are only two ways to tell somebody thanks: Kudos and Marked Solutions
    Unofficial Forum Rules and Guidelines

  • Question about waveform...

    Hi.. is me @ again....
    this time i wish to know something about waveform...
    erm... who can let me know about the setting x-axis??? i wish to do the seeting same as the picture below...
    hope somebody can help me...
    Jaxx
    Attachments:
    question.jpg ‏9 KB

    Right-click on your waveform graph and select "properties".
    Now Go to the "Format and Precision" tab, select "X-axis, relative time, HH:MMS". Click OK.
    (If you want exactly the range shown, disable autoscaling and enter 00:00:09 in the rightmost tick mark)
    LabVIEW Champion . Do more with less code and in less time .

  • A question about Waveform graph

    Hello everyone.. I have made a waveform graph to measure pressure with my DAQ NI-9237. The problem is the time value in the x-axis shown on the picture below. It only shows the measurements from 0 to 1, but i need from 0 to 4 seconds. 
    Thanks in advance
    Oesen
    Best regards
    Oesen

    Hi Oesen.
    It's because you convert your data to a double, which does not contain any information about the time. Instead, simply delete the 'Convert from Dynamic Data' and wire in the dynamic data directly to the chart. The Waveform Chart supports this datatype as well.
    Another solution is to keep the 'Convert from Dynamic Data', but instead of converting the data to doubles, you convert to a waveform. You do this by dobbel-clicking on the function and select 'Single Waveform' in the list. I personally think this is the best solution, since you are now able to work with your data in a way the dynamic datatype won't allow you. Try and wire the waveform to 'Get Waveform Components' and see how data is stored.
    You can read more about the waveform datatype here:
    Using the Waveform Data Type in LabVIEW
    http://digital.ni.com/public.nsf/allkb/B965F316364​DE17B862572DF00363B10
    I hope this information is helpful.
    Best Regards
    Alex E. Petersen
    Certified LabVIEW Developer (CLD)
    Application Engineer
    Image House PantoInspect

  • Question about documenting process maps and form object properties

    Does the new version of Workbench have a tool that allows us to print a report showing the properties of the object used in a form template or process map? For example... showing all of the properties like fonts, size, patterns, defaults, whether or not a field is required, etc...? I am also checking to see if this capability has been added to Workbench for Process Maps?

    No it does not but there is a blog entry by John Briinkman that will analyze your form template and give you some of that information. Here is a link to the blog entry:
    http://blogs.adobe.com/formfeed/2011/05/updated-form-report-tool.html
    Paul

  • Question about 'user process' in the context of Oracle

    The following is an except from oracle documentation.
    Overview of User Processes
    When a user runs an application program (such as a Pro*C program) or an Oracle tool (such as
    Enterprise Manager or SQL*Plus), Oracle creates a user process to run the user's application.http://download.oracle.com/docs/cd/B19306_01/server.102/b14220/process.htm
    As my understand, an user process is a piece of software that can connect to an oracle server. You (the user) can start a piece of this kind of software, then connect to oracle. If so, why Oracle creates a user process to run the user's application?
    Thanks.
    Edited by: Yang Shuai on Jul 6, 2011 10:20 AM

    Hi. I would suggest reading the 11.2 Concepts manual: it is much improved:
    http://download.oracle.com/docs/cd/E11882_01/server.112/e16508/process.htm
    This text is trying to say that the application starts a client process that can connect to the database. The database manages server processes and background processes; the application runs the client process.

  • Question about waveform chart time scale

    Hello,
    I have question regarding to time scale on my chart, I want  it to show the actual measured time, for example  from 0-30 seconds, but instead my minimum value is 302654789854 . Please help me to fix it.
    Regards ,
    Stella Deheryan

    You can modify the way the time is displayed on the axis by right clicking the chart and selecting properties. On the display format tab, select relative time. This should show the X-axis scale as HH:MM. Or pick any other type of formatting you want.
    Best Regards
    Michiel
    Applications Engineer
    NI Belgium
    http://www.ni.com/ask

  • Question about Batch processes in CS4

    Hello everyone,
    I was hoping there's a solution to my problem. My laptop's MoBo died recently so I wil be retrieving data from my HDD via another laptop. I created a Batch process in CS4 to resize and perform a few more actions on pictures. I was hoping to save that Batch process without having to recreate it. Are batch processes made by the user saved in a particular folder that I can just go into and copy?
    Thanks in advance for your help!
    Riley

    Did you save the action as an *.atn file using the context menu of the palette?
    If not, then the action is only "present" in one of the preferences files, together with all the other preferences.
    You can try to copy the preferences files, but I don't know whether the action will "come to life".
    Of course it must be the same version of photoshop on your other PC.
    :-) miss_marple

  • Question about waveforms

    Why exactly is the waveform of a mono recording asymmetric, i.e. the part below the line is different from the one above? And what does it mean when one part clips and the other doesn't?

    here's an image from GB:
    now if i take away the shading it looks like:
    which just looks like a waveform to me
    Grabbing an image from wikipedia:
    (posted under their license, from the entry: http://en.wikipedia.org/wiki/Waveform )
    since those are mathematically generated waves they are perfectly symmetrical, but your voice, or a guitar will never look like that, it would look like the second image above.
    Is that any clearer, or did i just muddy up the water more?

  • Some question about Sales Processing

    I am new to SD and would like to ask how to handle the following sales adjustment scenario
    Let say, at the beginning, material A is sold to Customer X at unit price $100. After delivery and billing (invoice already sent to customer), due to some business reason behind, the sales team agreed to lower the price, from $100 to $95. So how can I realize this case?
    Do I need to create a credit memo request, then credit memo to refund the adjusted amount (e.g the $5 per item) to customer?
    Can I just create a credit memo reference to the original billing and modify the condition value?
    Besides, how if the qty also need to be changed? When I created the credit memo from the billing doc, I found that I can only modify the condition value, but not qty.
    Does anyone have idea? Thanks!

    Hi Gundam,
    To create a credit memo request(G2) with reference, choose Sales document - Create with reference.
    The system displays a dialog box in which you can choose between six tab pages (inquiry, quotation, sales order, contract, scheduling agreement or billing document). In the tab page you can specify the document number of the reference document and either copy it completely or use Selection list to copy some of the items.
    You can use Selection list in the dialog box which appears when you create with reference to copy some of the items to the new document.
    To copy selected items in the new document, proceed as follows:
    Choose Selection list.
    Deselect the items you do not want to copy into the new document. If necessary, change the quantities of the items to be copied.
    Choose Copy to copy the selected items into the new document.
    After creating credit memo request,proceed further and create credit note using billing type G2(credit memo).
    regards
    kiran.

  • Takt-based planning. Some questions about the process

    Dear Friends and collegues,
    I would utilize takt based planning.
    I don't understand the mening of planning segment element, capacity planning element capacity planning visualization and control element.
    The SAP library is not clear.
    Anyway if I have a line with two stations where material is assembled shoul I create line segments or it's better to create two takts for the main line and do not create segments.
    Thank's in advance
    Luca Pastura
    Genova - Italy

    1) generally, is the BIEE database and application server decentralized with EBS database and application? Both BIEE 10g and 11g version can be integrated with EBS R12?You, shud consider OBI Application here which uses OBIEE as a reporting tool with different pre-built modules. Both 10g & 11g comes with different versions of BI apps which supports sources like Siebel CRM, EBS, Peoplesoft, JD Edwards etc..
    2) In BIEE administrator tool, the first step is to create physical tables. if the source appliation is EBS, is it still needed to create the physical tables?Its independent of any soure. This is OBIEE modeling to create RPD with all the layers. If you build it from scratch then you will require to create all the layers else if BI Apps is used then you will get pre-built RPD along with other pre-built components.
    3) if the physical tables creation is needed, how to complete the data transfer from the EBS source tables to BIEE physical tables? which ETL tool is prefer for most developers? warehouse builder or Oracle Data Integration?BI apps comes with pre-built ETL mapping to use with the tools majorly with Informatica. Only BI Apps 7.9.5.2 comes with ODI but oracle has plans to have only ODI for any further releases.
    4) During data transfer phase, if there are many many large volume data needs to transfer, how to keep the completeness? for example, it needs to transfer 1 million rows from source database to BIEE physical tables, when 50%is completed, the users try to open the BIEE report, can they see the new 50% data on the reports? is there some transaction control in ETL phase?User will still see old data because its good to turn on Cache and purge it after every load.
    Refer..http://www.oracle.com/us/solutions/ent-performance-bi/bi-applications-066544.html
    and many more docs on google
    Hope this helps

  • About multi process access BDB question

    I am designing one system using BDB.I have some questions about multi process access BDB.
    1.If there are two process, they are shared BDB cache or every one has self BDB cache? (My understanding is every process has cache by itself.)
    2.If one process write BDB and at the same time one process read BDB,how to make read processs can read data which write by write process just now?

    1.If there are two process, they are shared BDB cache
    or every one has self BDB cache? (My understanding
    is every process has cache by itself.)You can configure it either way. The cache is maintained as part of the so-called environment. The usual thing is to configure a shared cache. You need to read about environments in the BDB and BDB/XML documentation.
    http://www.oracle.com/technology/documentation/berkeley-db/xml/index.html
    2.If one process write BDB and at the same time one
    process read BDB,how to make read processs can read
    data which write by write process just now?Use transactions, set up deadlock handling, and think about what transaction isolation guarantees you need. Note that there are four different fundamental setups for BDB: DS, CDS, TDS and HA, which stand for Data Store, Concurrent DS, Transactional DS and High Availability. For read-write concurrency, you need TDS.
    http://www.oracle.com/technology/documentation/berkeley-db/xml/ref/intro/products.html
    For high concurrency at the expense of memory, consider using multi-version concurrency control (MVCC). You can read about it in the following thread, especially in George Feinberg's replies:
    Deadlock handling for beginners
    In addition, there is ample documentation included in the BDB/XML distribution. It's pretty complex, as BDB can be configured in many different ways.
    Michael Ludwig

  • Questions about upgrading from Exchange 2010 RTM to Exchange 2010 Service Pack 3

    I am preparing to perform an maintenance upgrade on our current Exchange 2010 Server, to Service Pack 3 (and any post-SP3 roll ups), but I have a couple questions about the process.
    Current Exchange Server details:
    Exchange 2010 Standard
    Version: 14.0 (Build 639.21) - from Exchange Management Console
    Version: 14.0.702.4000 - from Outook client
    Active Directory forest and domain levels: Windows 2008 R2 native
    The questions I have are:
    1.  Can I assume that because it's version 10.0.702.4000 I am on Exchange Server 2010 RTM Update Rollup 4?
    2.  Can Exchange 2010 Standard RTM be patched directly to Service Pack 3, or would I need to perform incremental patches (i.e. SP1, SP2, etc.) before going to SP3?
    3.  Do I need to manually perform the AD domain schema prep before applying Service Pack 3, or will the Service Pack 3 update process automatically handle the modifications of the AD schema?

    Hi,
    Here are my answers you can refer to:
    1. Firstly, I’d like to explain , we can use connection status to check our Exchange server version from Outlook client:
    http://office.microsoft.com/en-in/outlook-help/determine-the-version-of-microsoft-exchange-server-my-account-connects-to-HA010117038.aspx
    And I check my version from both EMC and Outlook client. It’s same.
    2. We can directly update RTM version to SP3 , and the update will take an additional 30 minutes or longer per database.
    3. Since Exchange 2010 SP3 makes updates to the Active Directory schema, we need prepare AD domain schema. However, it will automatically prepare AD and the domain when you install the update.
    For more information, you can refer to the following article:
    http://technet.microsoft.com/en-us/library/jj965774(v=exchg.141).aspx
    If you have any question, please feel free to let me know.
    Thanks,
    Angela
    Angela Shi
    TechNet Community Support

  • BCM payment question about House Bank

    Hello,
    I have a question about BCM process.
    If I want to create a payment batch which is related with a specific house bank and acct. id how can I do it?
    For example I need to test the payment for House Bank ABCD account id 123
    If I create an invoice in FB60 and then I pay this by the F110 and then I create the batch in BNK_MONi this batch has for example Hose Bank EFGH account id 123.
    But I need the payment are linked  to the House Bank ABCD account id 123.
    How can I do it?
    which is the link between the invoice and these fields?
    Hope the question makes sense
    Thank You

    Hi Larissa,
    What is the Ranking you have defined in FBZP. You have to define the proper ranking to achieve your requirement.
    In case you want the particular House bank, acocunt ID to be considered in a particular case and do not want to Change the ranking order, then Give thi shouse bank , account ID in Payment Run by editing the proposal. In this way, the Payment run will consider this.
    Regards
    Amitash

  • Questions about flashing the bios

    Hi everyone. I have a few questions about the process involved in a bios update.
    First, I should tell you I have a Lenovo G470 that sometimes has problems booting.
    The problem is I turn on the laptop and after 2-3 seconds it shuts down. I see the logo, and nothing else. After that I can spend hours trying to turn it on again, and keeps failing. After some time, I turn it on and use it without problems.
    Before these problems, I had experienced similar troubles, but I could fix it (in my way) and I explained it in this post: http://forums.lenovo.com/t5/Lenovo-3000-and-Essential/Lenovo-g470-shutdown-problems-in-intervals-of-...
    Ok, In that post a reply says that a possible solution could be a Bios update. So, I've been thinking to flash the bios to solve my actual problem, but I would like to ask you some questions:
    1. Updating the bios could be a solution for this case?
    2. How long does it take to update a lenovo G470 bios? (I ask this because I read that if a problem occurs in the middle the damage can be serious, and in the past I had these random shutdowns, so I'm a bit afraid)
    3. How am I sure if my bios is or not updated? (there's a way to check this from windows?)
    4. Finally, if you could give me a link to download the correct bios update I'll thank you.
    I think that's all. I apologize for my basic english and hope you could give me some clues on this, because, as you see, I'm a total newbie.
    Thanks!

    hi alemaneitor,
    Regarding your questions:
    1. Yes, flashing the BIOS may help solve your problem as it will re-write the configurations on the CMOS. Take note though of the changelogs or README (repair changes) as the latest BIOS updates fixes critical issues on the hardware.
    I've also seen some units that act the same as yours and doing a gpu reflow most of the time fixes the issue - see this thread in reference.
    2. In flashing the BIOS outside of Windows, it takes less than a minute. If you need to run the BIOS flash utility inside Windows, it may take 1-2mins.
    3. If there's a new BIOS that fixes critical issues, it's most of the time uploaded on the lenovo website (in some cases, BIOS updates are not available to the public and can only be used by service technicians)
    4. The latest BIOS update for the Lenovo G470 is the one below that fixes an issue on units that can not enter BIOS after restart under compatible HDD mode (see README.TXT)
    BIOS Update for 32bit Windows
    40cn33ww_32.exe
    3.28MB
    BIOS Update for 64bit Windows
    40cn33ww_64.exe
    3.67MB
    Regards,
    neokenchi
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

Maybe you are looking for

  • Can see Mac on Windows XP PC but can't access

    If I go to Network Places on our Windows XP machine and navigate down to the workgroups, I can see the workgroup that contains both the XP machine and Mac. But when I click on the Mac, it says I can't access it because I don't have proper permissions

  • Display of vendor name after giving  different freight vendor in me21n

    We have maintained a different vendor for freight in the PO at condition type level in me21n(conditions tab If we double click on that particular condition type we can see vendor where vendor can be given).We need to display vendor name seperately wi

  • Error in Master Group creation

    Hi Mahantesh Here, In Master Data while creating Company code data  & account Management tab page in that Reconcilation account option i m not getting what to enter there. Its not accepting any value there like 140000, Pls help me.

  • HT1819 'Byte-Range' request error, but no problems using Advanced menu

    On Windows Vista PC, latest iTunes update: No trouble subscribing to podcast feed using Advanced menu. iTunes will even update/load new episodes, but I receive 'byte-range' request error when submitting podcast feed to the directory. Is it normal to

  • Back To My Mac; does it wake the iMac from sleep?

    Back To My Mac sounds promising. But, it is nowhere mentioned whether it wakes the Mac up from sleep or even starts it up when contacted from afar? If not, it is not that useful!