Quick FYI: WaterCooling Block compatible with the MSI K8N Master2-FAR
If you're like me, you hated the noise from the stock CPU fans on the K8N Master2-FAR... well I did alot of searching and couldnt find any difinitive information about what fit, or didnt fit, on that motherboard as far as heatsinks or cooling blocks.
I just finished installing a water cooling system in my system, and I used the PolarFlo E-Series CPU blocks, and they fit perfectly!
http://www.frozencpu.com/ex-blc-218.html
Anyone else have any confirmed working heatsinks or water blocks for the K8N Master2-FAR board?
Hi
I`m using 2 of this
http://www.alphacool.de/xt/product_info.php/products_id/348/cPath/5_18_66_184/cpu-kuehler-xeon/wak-cpu-alphacool-nexxxos-xp-bold-xeon-603-604.html
with my 2 Opteron 265.
Case is a Lian Li PC7 SE-B.
Pic inside:
http://www.forumdeluxx.de/forum/attachment.php?attachmentid=22159&stc=1&d=1145233096
So long
Insane
Similar Messages
-
MSI K8N Master2 FAR + 7800GTX problem
It doesn't work after install graphic driver.
I have tried few ver. of drivers(include the newest one)
Does anyone can tell me how to fix this issue?
My system spec.:
Dual AMD Opteron 246
MSI K8N Master2 FAR
2x Kingston 512MB DDR400 ECC+REG
Colorful 7800GTX
4x Hitachi 120GB 8M
OCZ Powersteam 520W Power Supply Unit
Has Been switched to Non-SLi mode.Quote from: Nexus++ on 04-November-05, 06:55:31
It doesn't work after install graphic driver.
I have tried few ver. of drivers(include the newest one)
Does anyone can tell me how to fix this issue?
My system spec.:
Dual AMD Opteron 246
MSI K8N Master2 FAR
2x Kingston 512MB DDR400 ECC+REG
Colorful 7800GTX
4x Hitachi 120GB 8M
OCZ Powersteam 520W Power Supply Unit
Has Been switched to Non-SLi mode.
I have one question for you. The motherboard has three power connectors. A 24 pin , a 8 pin and a 4 pin. Looking at your specs i see that you have the OCZ Powersteam 520W Power Supply Unit. I looked at a review of this PSU and it has the following connectors for this: 20+4 connector and a 4+4 connector. So the 24 pin and the 8 pin connectors are covered. All the pci-e connectors i see are 6 pins, also for this PSU. What did you do with the 4 pin connector close to the pci-e slot? -
Another little niggle with the MSI K8N SLI Platinum
Hello, I have just been benchmarking using Everest.
I did a mem read test and the result below is wrong, I have an amd64 venice 3200.
I had run this test earlier in the day and it was showing the 3200.
CPU CPU Clock Motherboard Chipset Memory Read Speed
Athlon64 2000 MHz MSI K8N Diamond / K8N SLI Platinum (MS-7100) nForce4-SLI Dual PC3200 DDR 5270 MB/s
thanks
ps. I have just noticed that outlook express is taking twice as long to open :(
pps I must have had to much to drink, or something just got logs from mirc and here is what it said
Athlon64 2000 MHz MSI K8N Diamond / K8N SLI Platinum (MS-7100) nForce4-SLI PC3200 DDR SDRAM 3045 MB/s
This is what it is reading after sorting the ram stick problem out.
CPU CPU Clock Motherboard Chipset Memory Read Speed
Athlon64 2000 MHz MSI K8N Diamond / K8N SLI Platinum (MS-7100) nForce4-SLI Dual PC3200 DDR 5259 MB/s
Sorry for time wastingSorry flow, took to long to edit post
https://forum-en.msi.com/index.php?topic=88965.0
this explains a little, and yes I have just built this comp, first attempt at a serious upgrade. Apart from problems with faulty stick of RAM in the beggining everything has run smoothly.
Then I discovered benchtesting and as I said earlier, am a bit how can I say it, mellow so thanks for the reply, and I hope you are still here when I attempt to overclock
I knew I should have come here first -
MSI K8T Master2-FAR won't boot!!
Ok, I have the Athlon 64 FX-51 with the MSI K8T Master2-FAR. I have one gigabyte of REGISTERED Memory (Corsair), 500W Power Supply, 120GB Seagate SATA HDD, DVD, DVD-RW, FDD, & 250MB Zip Drive. Everything is (as far as I know) installed properly, but when I try to power it up, it doesn't start up. Nothing will come on the screen, but the fans spin properly, and the motherboard speaker beeps at me (telling me something is wrong). ANY advice will be graciously accepted.
Quote
Ok, I have the Athlon 64 FX-51 with the MSI K8T Master2-FAR. I have one gigabyte of REGISTERED Memory (Corsair), 500W Power Supply, 120GB Seagate SATA HDD, DVD, DVD-RW, FDD, & 250MB Zip Drive. Everything is (as far as I know) installed properly, but when I try to power it up, it doesn't start up. Nothing will come on the screen, but the fans spin properly, and the motherboard speaker beeps at me (telling me something is wrong). ANY advice will be graciously accepted.
Wow, that sounds like a killer system. I have not had a lot of experience with this motherboard, so my ideas here are going to be pretty general. The speaker beep is a POST message: the number and length of beeps should correspond to the failed check when starting your computer. You'll want to check in the mobo manual for a chart of post beeps and the associated failures.
Otherwise, you can check your video card to see if it is working. Make sure it is firmly seated in the AGP slot, and make sure you have supplied the additional power connector (needed for most high end graphics cards). Also, try removing one DIMM (stick of memory) and see if it boots that way and try moving around the remaining DIMM if it still wont boot.
Similar problems often occur when your system does not recognize or support the RAM at SPD settings (or whatever you set them to last). Clear the CMOS and restart if you have changed the settings yourself (this will put them back to the defaults). If you have not changed the memory timings, you could try booting up with other memory modules, and then swapping them out after you have gotten the system to boot (this might be difficult since you need to find registered modules).
More information would be helpful... post the current over your PSU drive rails. Just saying that it is 500W is not enough.
As long as your CPU fans are moving, you shouldn't be damaging anything by trying different things. However, when you stop and restart your system, always wait for a little while for the power in your PSU to dissipate (you should hear a "PZZT" sound). Otherwise, if you keep starting and restarting your computer, you may blow something up.
Good luck!
-Angler -
FYI!!! Not 1 FM modulator on the market is compatible with the iPhone!!!!
Well I just wasted my whole day and ****** off everyone in customer service (returning FM Mods) trying to find one that would work, and guess what... THERE IS NOT ONE OUT THERE THAT IS COMPATIBLE WITH THE iPHONE. So I have 13 days to return my phone for a refund, so I’m giving Apple 12 days to fix this problem. Really, if Apple is going to have a $700 part time phone/part time iPod they can keep it. I'll gladly go back to my SLVRL7 and call it a day. How in the world (it’s 2007) do you not release a FM modulator compatible with the iPhone?? Don’t tell me they’re worried about losing money, this is a $700.00 phone, not everyone is going to stop buying iPods… I just don’t get it. It does bother me that I now have to buy a new FM Mod, but not even a 1/6th as much as it bothers me that Apple didn't release one, I mean they only had a couple of years to design one.
I at least hope this keeps someone from wasting their day.
Brands I’ve tried. (several versions of each)
Monster
Griffin
Belkin
Couple other generic brands1. Apple never released any of the iPods with FM receivers. 3rd party companies do.
2. Apple posted their iPhone specs long before it was released. Did you bother to even read the spec page? I know you must have because no one would blindly spend "$700" on a product.
3. All 3rd party FM tuners are made after the iPod was released (at least to be compatible with the current known generation.
4. The iPhone was released a few days ago. Try giving 3rd party companies some time? -
Is quick time pro 7 compatible with ipad2
Is quick time pro 7 compatible with Ipad2
the most you can do with quicktime pro is make videos that you sync onto the iPad.
-
I'm unable to backup my iphone. It is saying 'iTunes could not backup because the backup was corrupt or not compatible with the i Phone.' i deleted my previous back up but it still isn't helping. Any suggestions ?
Mac: ~/Library/Application Support/MobileSync/Backup/
Windows XP: \Documents and Settings\(username)\Application Data\Apple Computer\MobileSync\Backup\
Note: To quickly access the Application Data folder, click Start, and choose Run. Type %appdata% and click OK.
Windows Vista and Windows 7: \Users\(username)\AppData\Roaming\Apple Computer\MobileSync\Backup\
Note: To quickly access the AppData folder, click Start. In the search bar, type %appdata% and press the Return key.
Delete the entire Backup folder if there is anything at all in it. -
Need a pop up blocker compatible with Mavericks
The old pop up blocker I was using isn't compatible with the update and has been put some folder. Although it wasn't brilliant it was much better than the in built Safari one and was wondering if anyone knows of one I could use instead? Thanks.
Reinstalling it from their web site did work after a couple of attempts.
When the GlimmerBlocker installer asks to install Java 6, let it install it and then relaunch the GlimmerBlocker installer. (Java 6 includes a library which isn't included in OSX and which newer java versions need). You might have to install the public java runtime.
Note: I still had ads until I Unchecked- Activate Glimmer Blocker, (in menu bar under setup), and then Check mark it back On. -
Content Tab: None of the fact tables are compatible with the query request
Hi All,
**One thing I am not clear yet of all my years with OBIEE is working with the content tab in BMM.**
I have made a rpd the joins in physical layer as shown below:
https://picasaweb.google.com/114804305606242416264/OBIEEError#5663056545119428530
And the BMM layer as:
https://picasaweb.google.com/114804305606242416264/OBIEEError#5663056519553812930
Error I am getting when i run a request from the 3 columns from the selected 3 tables is:
Dim - Comment Code Details
Fact - Complaint
Dim - Service Details
Error Codes: OPR4ONWY:U9IM8TAC:OI2DL65P
State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 14020] None of the fact tables are compatible with the query request Sr Num:[DAggr(Fact - Complaint.Sr Num by [ Dim - Service Details.Sr Cat Type Cd, Dim - Comment Code Details.Cmtcode name] )]. (HY000).
I get no error for consistency.. I read everywhere and I know i need to set the appropriate aggregation levels in the various dims and facts LTS properties to help OBIEE understanding our model, but how to do that.. how do i decide... how should I approach, what should be the aggregation level, what details.
When i click More button i see different options: Copy, Copy From, Get Levels, Check Level, what do these mean.
Aggregation Content, group by - Logical Level or Column which one should i choose and how should I decide.
Can anyone explain the Content Tab in details and from scratch with some example and why we get these errors.... I know many people who are well versed with many other things related to RPD but this. A little efforts of explaining from you guys will really be appreciated.
Thanks in advance,
DevHi Deepak,
Option 1:
My tables in physical layer are joined as below:
D1--> F1 <--D2--> F2 <--D3
Same way i model it in BMM
D1--> F1 <-- D2--> F2 <--D3
Here D1 is non Conformed Dimension for F2 and D3 is non Conformed dim for F1. Later create Dimensional hierarchies, I tried setting up the content levels
I go Sources>content tab of Fact F1 I set
Dimensions----------- Logical level
D1---------------------- D1 Detail
D2---------------------- D2 Detail
D3---------------------- D3 Total
then, I go Sources>content tab of Fact F2 I set
Dimensions----------- Logical level
D1---------------------- D1 Total
D2---------------------- D2 Detail
D3---------------------- D3 Detail
Then, I also go in all the dimensions and set their content levels to Details, but it still gives me errors not sure where I am going wrong in setting the content levels.
I need to know whether the way I have modeled it in BMM is right,
Option 2:
I can combine the two facts in a single Logical Fact or the above design should also work.
(F1&F2)<--D1, D2 , D3 joined separately using complex logical joins.
what will be the content tab details?
Thanks,
Dev -
Bridge CC no compatible with the new After Effects CC 2014 ?
Hi, I'm updating the Adobe suite (CC 2014) .but After Effects CC 2014 no longer works with the old Bridge CC (there is no update of Bridge). Since "browse presets" in After Effects when choosing a preset (dissolves etc) there is an error message:
"After Effects error: can not import file" Entries lum.-marq.calque.ffx "unsupportedfiletype or extension (0 :: 1). With all presets.
I tried on other computers with other adobe updated it makes such licenses except with the old version of adobe after effects (after CC effects) I tried too to change language of Bridge and After effects (beharps this is a langage compatibility problem) but the problem is the same.
So I think the new version after effects CC 2014 is not compatible with the presets adobe bridge CC ??
How can I do? I have to go through the old version of after to apply a preset Bridge? I can not even download it in cloud creativ ... there is only the new version of after effects...You need to ask in Community: Premiere Pro | Adobe Community but do not expect Adobe to discuss future plans
https://www.adobe.com/cfusion/mmform/index.cfm?name=wishform for bug reports or feature requests
This forum is about the Cloud as a delivery process, not about using individual programs
If you start at the Forums Index https://forums.adobe.com/welcome
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says All communities) to open the drop down list and scroll
Also, this is an OPEN forum, not Adobe support... please do not post personal information -
I bought a new imac running Loin with Office 2011. I am the only mac in the office and the Server we use to access emails runs exchange 2003 and my IT person says the imac is not compatible with the server. The server does not want to let me access using any email software other than webmail access through our website. It looks as though 2011 is not compatible with 2003 per some searches online, but what are some options I have to gain full access again? I purchased parallels in hopes that this my help and I am able to use remote desktop connection to log on to server but can not drag and drop files I need. There is a shared drive on that Server we all use to exchange files.
The two main issues are gaining access to my email again and ability to drag and drop files from mac to pc. I hope this is enough info to get some solutions.
PS - IT person says my iMac's IP is what his server does not understand so that is why I can not login.Office 2011 is not compatbile with Exchange 2003.
I suggest you post further Office related questions on Microsoft's own forums for their Mac software:
http://answers.microsoft.com/en-us/mac -
I've got a new iPad and am trying to do an iCloud backup but keep getting the following message: no iCloud backups are compatible with the version of iOS (6.1.3) on this iPad.
How do I restore info from iCloud onto my new device?You would have to update your device first, before you can restore your iPad from your backup. Resolution: set it up as anew device, then update your device to the latest version "Settings > General > Updates", then reset your device again "Settings > General > Reset > Erase All Content and Settings" and then after the iPad restarts again, choose to restore your device from your backup.
-
I downloaded CS6 and am having issues with my print driver. It is not compatible with the HP 2600n and have tried to download drivers given to me by adobe ( (Jupiter 3) but it is not working. after a few days. Its a temporary fix and is still looking for the HP driver when i boot up. It also will not save in any print or postscript format. Does anyone know how to fix?
Currently use a Mac with the latest Mavericks 10.9.4Oh boy! Acting kind of weird seems to be an understatement, aquaequus!
What type of troubleshooting were we able to do with you? I want to make sure that we can get some sort of resolution for this problem.
It is quite possible the battery door may get your phone in working order again. I'm not sure if the store has it in stock, but it is available in our warehouse for $14.99 which can be ordered via customer service.
Tamara H.
Follow us on Twitter @VZWSupport -
When i try to boot itunes, screen goes black and a message pops up and says not compatible with the visual elements. how do i fix this? itunes wont even open at this point. please help. thanks
Let's first try the following document, only be sure that none of the boxes in the compatibility mode tab are checked (not just the compatibility mode box itself):
iTunes for Windows: How to turn off Compatibility Mode -
Error :"The provider is not compatible with the version of Oracle client"
Hi guys!
I'm facing this problem:
When my .Net application tries to access the DB, I get this error message above.
The application is into the same machine of DB and the operational system is Windows Server Enterprise 64 bits.
I'm comparing to another machine that has the same scenario but runs in Windows Vista 64 bits. This problem doesn't happen and I can normally access the DB.
The both database versions are 10g Release 2 (10.2) and all components from Oracle Database Components 10.2.0.2.21 are installed as the containing bellow:
-Oracle Data Provider for .NET 1.x 10.2.0.2.20
-Oracle Data Provider for .NET 2.0 10.2.0.2.20
-Oracle Developer Tools for Visual Studio .NET 2003 10.2.0.2.20
-Oracle Developer Tools for Visual Studio 2005 10.2.0.2.20
-Oracle Provider for OLE DB 10.2.0.2.20
-Oracle Objects for OLE 10.2.0.2.20
-Oracle Services For Microsoft Transaction Server 10.2.0.1.0
-Oracle Net 10.2.0.1.0
-Oracle Universal Installer 10.2.0.2.0
Oracle.DataAcces.DLL is 2.102.2.20 and it is reference in my .Net app (that is published and located into IIS).
These are the Oracle assemblies installes in 'C:\Windows\Assembly':
Windows Vista Machine:
ASSEMBLY NAME VERSION CULTURE PUBLIC KEY TOKEN PROCESS ARCHITECTURE
Oracle.DataAccess 10.2.0.100 Neutral 89b483f429c47342
Oracle.DataAccess 1.102.2.20 Neutral 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 pt-BR 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 it 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 fr 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 es 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 de 89b483f429c47342
Oracle.Management.Omo 2.102.2.20 Neutral 89b483f429c47342 x86
Oracle.VsDevTools 2.102.2.20 Neutral 89b483f429c47342 x86
Policy.10.1.Oracle.DataAccess 1.102.2.20 Neutral 89b483f429c47342
Policy.10.2.Oracle.DataAccess 1.102.2.20 Neutral 89b483f429c47342
Windows Server Machine:
ASSEMBLY NAME VERSION CULTURE PUBLIC KEY TOKEN PROCESS ARCHITECTURE
Oracle.DataAccess 10.2.0.100 Neutral 89b483f429c47342
Oracle.DataAccess 1.102.2.20 Neutral 89b483f429c47342
Oracle.DataAccess 2.102.2.20 Neutral 89b483f429c47342 x86
Oracle.DataAccess.resources 10.2.0.100 pt-BR 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 zh-CHT 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 zh-CHS 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 ko 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 jp 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 it 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 fr 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 es 89b483f429c47342
Oracle.DataAccess.resources 10.2.0.100 de 89b483f429c47342
Policy.10.1.Oracle.DataAccess 1.102.2.20 Neutral 89b483f429c47342
Policy.10.2.Oracle.DataAccess 1.102.2.20 Neutral 89b483f429c47342
Policy.9.2.Oracle.DataAccess 10.2.0.100 Neutral 89b483f429c47342
Policy.9.2.Oracle.DataAccess 1.102.2.20 Neutral 89b483f429c47342
What should I check and do to solve this problems?
Thanks for help,
AndersonHi,
Often the error "The provider is not compatible with the version of Oracle client" is raised when the unmanaged dll OraOpsX.dll can't be found, can't be loaded, or is the wrong version. For version 10.2.0.x of ODP.NET and .NET Framework 2.x the file should be called "OraOps10w.dll" and should be found in the %ORACLE_HOME%\bin directory.
Since the ODAC pieces are installed on the same host as the database, are they in a separate Oracle Home or the same Oracle Home as the database software? If there are multiple Oracle Home directories, which one is in the system path first?
I would start with verifying the version of OraOps10w.dll and the system path on the server. You might also confirm that the Oracle Home directory (and everything under it) has the following permissions for Authenticated Users:
- Read & Execute
- List folder contents
- Read
Regards,
Mark
Maybe you are looking for
-
Hi All APex Fans, I'm in the process fo deploying a public application . ( i.e. zero authentication) My URL is a typical HTMLDB URL which reveals certain key fields depending on which page of the application you are : https://xx.xx.xx/htmldb/producti
-
is there a way to address email (i.e. a word or some code) that would place that email in a specified inbox folder? not using internal rule, rather the beginning of this sort happening as it comes in? In other words I tell a friend if he is emailing
-
I cannot see toolbar with favourites, file etc so i cannot join any pages to my favourites. Where it's gone...?
-
Unity connection - how to verify if an email of the voicemail is being sent out
Hi Guys I am running unity connection 8.5 and I am integrated with exchange 2010. Single inbox seems to be working fine for all users except one. The users info in unity connection looks fine and is pulling down from AD using the LDAP integration jus
-
Elements 4.0 (MAC) was working fine, now it "Quits unexpectedly"...
PSE 4.0 had been working just fine, even with my limited knowledge of it. One day I tried to open it and got the error message "Application quit unexpectedly..." I tried to uninstall then reinstall and it still is not working. Is there something I ne