Quicktime does not show USB 2861 device as a camera

This device is the hardware known as Video 2 Go from Ionaudio. Now the documentation states that (for Snow Leopard) one should:
first, install their bundled software (VideoGlide from Echofx) and register it;
secondly, set QT (via Get info selection) to run in 32bit mode;
before trying to use the device with QT or iMovie as an input device.
Now I don't run 10.6.x - I have 10.7.5 installed and some person else has 10.8.x installed and in both cases we find that QT does not show the device as a "composite" camera (or Video input device) when trying to do a "New Movie Recording". It is though recognised as an audio input device (in QT) and it does show up in the USB tab of the System Info report when connected.
Is there any suggestions that I should tweak?

Firstly, make sure that your device is not hidden (left hand pane). If it just reads device then toggle between SHOW and HIDE.
Secondly, try all the other ports on your computer, even a number of times.
Thirdly, if you have another computer try plugging your device into it without taking any action, give it a moment, remove it and try it back in your other computer again.
Failing all that, see here - http://support.apple.com/kb/TS1591
And failing all that put the device into Recovery mode. See here and note the paragraph 'If you restore from a different computer.... ' down near the bottom of the page -
http://www.apple.com/support/ipad/assistant/itunes/

Similar Messages

  • TS1538 My ipod touch will not connect to itunes. I reset the ipod touch. uninstalled itunes and installed it. Turned off firewall however the device manager still does not show Apple mobile device usb. What should i do next? I have windows 7.

    My ipod will not connect to itunes. I reset the ipod touch. uninstalled itunes and installed it. Turned off firewall however the device manager still does not show Apple mobile device usb. What should i do next? I have windows 7.

    See:
    iOS: Device not recognized in iTunes for Windows
    I would start with
    Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7

  • I have a macbookpro. when I connect any camera to the mac it does not show as a device. How do I load my pictures to either iPhoto or Aperture? It worked before but just stopped working. Any suggestions?

    I have a macbookpro. I use Aperture and Iphoto. When I connect any camera to the Mac it does not open it as a device in Iphoto, Aperture or in Finder. It use to work but just stopped. Any sugestions?

    Here is the full story. It may be long so please bear with me. I take a lot of pictures and movies. Since I have over 30,000 pictures I decided to place the Iphoto library on an external drive to save space on my internal drive since ot was getting very full. After I did that it worked fine for a while. Then one day I could not open the Iphoto library. Since I was overseas at the time I brought it to the IStudio ( not an Istore) overseas. They said to rebuild the library and they would do that for me. It took all day since I had so many pictures. When they called me and told me it was ready, I went to pick it up. They started to show me the new library. It crashed again. Not knowing how to fix this at the ISudio, they installed Aperture and imported the Iphoto library. This worked fine for a short time.When back in the states, it crashed again just like Iphoto. I took it to the IStore. They did not know why the overseas Istudio did what they did what they did  and rebuilt my aperture library. Again it worked fine. Now that I am overseas again. It crashed again. However, I concluded that the reason for these crashes is becuase I have the file on an external drive that derives its power from the Mac and not by itself. When I use it and stop for a while the MAC will go to sleep and this cuases the external drive to shut down. This then causes the library to have inconsistancies. Therefore, when it happened this time I tried to repair the library and after 36 hours it would close down Aperture. Therefore I decided to rebuild the library. That did not work either. So I tried opening the Aperture library with Iphoto. That seemed like it was going to work but after importing half of the 30,000 plus pictures. I photo shut down. I then made a new aperture libary and erged the old library with it. This worked. I now have an aperture library that works. However, when I plug my camera into the MAC nothing happens. The camera does not show up in devices in either Aperture, I photo nor in Finder. The USB port and cord I use works fine becuase I can read my external hard drives fine. I checked as SIG suggested in this thread and everything is set to open aperture when the camera is connected.
    I have the newest OS version 10. 7. 2 and the computer frequently updates all my programs. I have not installed any ne software lately. The problem happens both if I am on battery or plugged in. Just before I came overseas the IStore replaced the Battery.   I can go back to the IStudio  here overseas but the last time I was there and told them about the problem ( I did not have my computer with me) they did not impress me with their wisdom. I will be back in that city in a month and can go there if need be.  Thanks for all the help so far. God bless.

  • My IPhone does not show up under Devices in I Tunes when I plug it into my computer. "Devices" no longer appears on the menu at all down the side of the page.

    My IPhone does not show up under Devices in I Tunes when I plug it into my computer. "Devices" no longer appears on the menu at all down the side of the page.

    Hope this helps:
    http://www.apple.com/support/iphone/assistant/itunes/

  • My new iPad mini does not show under manage devices

    I just purchased a new iPad mini for my husband. I removed his old one from the section of iTunes that reads manage devices. And even though his new iPad mini is synced and backed up, now the new one does not show under manage devices.
    Can anyone tell me how to get it to show up? I called Apple support and the lady trying to help me did not even know what I was talking about.
    Thank you.

    If you're on Windows read this support article.
    If on Mac, read this one.

  • Ipod touch does not show up under Devices in iTunes, but it does in iPhoto

    My iPod touch does not show up under Devices in iTunes, but it does show up under iPhoto.  Can anyone help troubleshoot this problem?
    Thank you for your help.

    try following the info here
    http://support.apple.com/kb/TS3694#error1611
    Error 1611: This error may indicate a hardware issue with your device.  Follow the steps  in this article. Also attempt to restore while connected with a  known-good 30-pin Dock Connector cable, computer, and network to isolate  this issue to the device. The MAC address being missing or the IMEI being the default value (00 499901 064000 0)  can also confirm a hardware issue. Out-of-date or incorrectly configured proxy or security software, such as FoxyProxy, can cause error 1611.    To troubleshoot third-party security software, follow these steps.

  • TS3716 installed the new itunes and now my ipod nano  does not show in the device menu

    installed the new itunes and now my ipod nano  does not show in the device menu

    There's a couple of ways to get through to the authorisation controls in the 11.0.x versions.
    The control is still in the Store menu, but first (if you're using iTunes versions 11.0.x) you might need to bring up the menu bar to see the Store menu.
    If you're using 11.0.x, click on the wee boxy icon up in the top-left corner of your iTunes to see the "Show Menu Bar" control, as per the following screenshot:
    Then you'll find the control in the Store menu:
    Alternatively, if you don't want to bring up the menu bar, it's still possible to get into the authorise controls via nested menus accessible from the wee boxy icon. Here's a screenshot of where to find them:

  • W520 Smart Card reader does not show up in Device Manager

    W520 Smart Card reader does not show up in Device Manager.
    It was working before and now nothing.  Nothing happens when SD card plugges in.
    Could my smart card reader stop working or is this a configuration issue?
    Any thoughts?
    thanks
    Ian

    Hi  Ian,
    Welcome to the community, and thanks for the post.
    The issue is related with software, to resolve this you need to re-install the card reader driver from the below mentioned web link.
    http://support.lenovo.com/en_SG/downloads/default.page?
    After that check if the issue get resolved.
    Regards,
    Sameer
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Kindle does not show up as device when plugged in USB

    I was trying to transfer some files to my Kindle using the USB port. I have a Kindle 2, and a Rocketfish Micro USB cord. The Kindle does charge up so it is drawing power through the cord. But the Kindle does not show up as a device attached to my MacBook. My external HD (Firewire) and iPods (USB) all work perfectly through this USB hub.
    I did call Apple (using my 30 day warranty for installing Snow Leopard) and the tech support person did not even know what a Kindle was.
    Amazon says it's an Apple problem.
    Apple doesn't seem to have any clue.
    I've seen from various threads that USB devices do seem to have intermittent problems. Is the Kindle one such device?

    Some devices do not work properly through a hub. Plug the kindle directly into your Mac and see if it works. Just because some devices work through a hub, doesn't mean all devices work through a hub. Apple does not support third party devices or third party hubs.

  • AppleTV does not show up in Devices in iTunes on streaming MacBook Pro

    My setup:
    - AppleTV connected wirelessly to the wireless router (Apple Extreme N Base Station).
    - Windows PC wired to the router and set up as machine that is sync'd to the ATV.
    - MacBook Pro connected wirelessly to the router and set up as a streaming machine.
    - All machines run iTunes 7.3.
    The AppleTV appears as a device on the Windows PC. No problem there.
    However, the ATV does not appear in the Devices list on the MacBook Pro 99% of the time and so I am not able to select it and change the photo albums I want to link. It occasionally appears. But I have not found a pattern to why it appears and disappears. Even when it does not appear in the Devices list, streaming from the MacBook Pro works just fine. So even as I am streaming, say, a podcast from my MacBook Pro, the ATV never appears as a listed Device.
    I can make the ATV temporarily appear by unlinking the MBP from the ATV and relinking it. During the link process, the ATV appears in the Device list. But it disappears as soon as the code is entered in the MBP.
    Confounding problem.

    how would
    it be if your mac continued to show every network
    device, firewire/usb drive that it had ever connected
    to whether they were still connected or not.
    Yes, it would be annoying if EVERY device that my Mac had ever connected to did show up all the time even after they were disconnected.
    However, there are some classes of devices that you do want your Mac to remember and show as available if they are detected active on a network. An example would a Bluetooth device that you have deliberately paired and designated in the Favourites list. If it was subsequently decided that this device should no longer appear, then removing it from the Favourites list does that.
    In my opinion, the AppleTV should fall in the same category. Since pairing is required and subsequent dissociation is possible by removing it from the iTunes list of allowed AppleTV units, then it should appear on iTunes' list of Devices as long as it is detected on the network. If the ATV is unpowered or if the PC moves onto a different network, that that ATV should not appear in the Devices list. There is an advantage for the logic to be implemented this way for the reason I have mentioned in an earlier post (i.e. being able to change the list of photo albums designated as available for streaming without having to go to the ATV, select the source PC, then going back to the PC to change the list).
    But again, just my opinion. It's always good to discuss these things so that others can see different opinions on an issue.

  • Graphics Card Does Not Show Up In Device Manager (Re: Installing AMD Video Drivers - Windows 8.1 (Step-By-Step Tutorial)

    This tutorial is a step-by-step tutorial on how to "fix" issues of a new graphics card not appearing in Windows 8.1 Pro, or not appearing (as a device) in Device Manager, or it's not being detected by Windows 8.1.
    This is the "second part" of a Step-by-Step Tutorial on how to install AMD Radeon graphics card drivers in Windows 8.1 Pro.
    GRAPHICS CARD IS NOT DETECTED AND DOES NOT SHOW UP IN WINDOWS 8.1 DEVICE MANAGER
    This problem can appear if the video card is not installed properly in the PCI slot and as a result the card is not detected in device manager. Check the physical connections again, reinsert the card properly in the PCI slot, check the connections (including the power cables going to the video card, and ensure that the fan on the graphics card is spinning and the card does have power and is properly seated/inserted) and then install the drivers from the manufacturer’s website.
    If the video card is in fact installed properly, but the problem of the video card not being discovered/found by the operating system persists, then try these following methods below to check if this solves the problem.
    Method 1:
    First, I would suggest you to run the following Microsoft Fixit to get the problem automatically detected and fixed. This Microsoft "fixit" App checks if the device is currently disabled or turned off or the driver is not installed.
    Hardware devices are not working or are not detected in Windows.
    http://support.microsoft.com/mats/hardware_device_problems/en-us
    Method 2:
    Sometimes, some devices in device manager are hidden due to corrupt or missing drivers.
    Follow the steps below to show hidden devices in the device manager and troubleshoot accordingly.
    Press the Windows key + X
    Select Command Prompt (Admin)
    Type set devmgr_show_nonpresent_devices=1 and hit enter
    Type Start DEVMGMT.MSC and hit enter.
    Once in Device Manager hit the View menu and select show hidden devices.
    From here, remove each instance of the AMD or Nvidia card you see as well as each unknown device. Exit Device Manager and reinstall the latest drivers you can find for your graphics card.
    After you install the drivers, reboot and see if you get any different results.
    If the above solved your problems and the Graphics Card is now working and is now being properly detected/displayed in Windows Device Manager:
    If your graphics card is now being detected by Windows 8.1 in Device Manager, but has a "yellow exclamation" mark (or video drivers are not found or not properly installed or the device is disabled) then install the latest graphics card drivers and proceed with this Step-by-Step Tutorial on how to install AMD Radeon graphics card drivers in Windows 8.1 Pro.
    Method 3:
    If methods suggested above does not help, I would recommend you to contact Apple/AMD/NVIDIA to get the latest chipset, BIOS, graphics card drivers installed properly.

    This tutorial is a step-by-step tutorial on how to "fix" issues of a new graphics card not appearing in Windows 8.1 Pro, or not appearing (as a device) in Device Manager, or it's not being detected by Windows 8.1.
    This is the "second part" of a Step-by-Step Tutorial on how to install AMD Radeon graphics card drivers in Windows 8.1 Pro.
    GRAPHICS CARD IS NOT DETECTED AND DOES NOT SHOW UP IN WINDOWS 8.1 DEVICE MANAGER
    This problem can appear if the video card is not installed properly in the PCI slot and as a result the card is not detected in device manager. Check the physical connections again, reinsert the card properly in the PCI slot, check the connections (including the power cables going to the video card, and ensure that the fan on the graphics card is spinning and the card does have power and is properly seated/inserted) and then install the drivers from the manufacturer’s website.
    If the video card is in fact installed properly, but the problem of the video card not being discovered/found by the operating system persists, then try these following methods below to check if this solves the problem.
    Method 1:
    First, I would suggest you to run the following Microsoft Fixit to get the problem automatically detected and fixed. This Microsoft "fixit" App checks if the device is currently disabled or turned off or the driver is not installed.
    Hardware devices are not working or are not detected in Windows.
    http://support.microsoft.com/mats/hardware_device_problems/en-us
    Method 2:
    Sometimes, some devices in device manager are hidden due to corrupt or missing drivers.
    Follow the steps below to show hidden devices in the device manager and troubleshoot accordingly.
    Press the Windows key + X
    Select Command Prompt (Admin)
    Type set devmgr_show_nonpresent_devices=1 and hit enter
    Type Start DEVMGMT.MSC and hit enter.
    Once in Device Manager hit the View menu and select show hidden devices.
    From here, remove each instance of the AMD or Nvidia card you see as well as each unknown device. Exit Device Manager and reinstall the latest drivers you can find for your graphics card.
    After you install the drivers, reboot and see if you get any different results.
    If the above solved your problems and the Graphics Card is now working and is now being properly detected/displayed in Windows Device Manager:
    If your graphics card is now being detected by Windows 8.1 in Device Manager, but has a "yellow exclamation" mark (or video drivers are not found or not properly installed or the device is disabled) then install the latest graphics card drivers and proceed with this Step-by-Step Tutorial on how to install AMD Radeon graphics card drivers in Windows 8.1 Pro.
    Method 3:
    If methods suggested above does not help, I would recommend you to contact Apple/AMD/NVIDIA to get the latest chipset, BIOS, graphics card drivers installed properly.

  • My Laptop Pavilion 9700 will not recognize DVD/CD drive. Does not show up in Device Manager

    My laptop Pavilion 9700 will not recognize the DVD/CD drive:
    The drive does not show up in the Device Manager’s list:  The disk spins and the light is on: Use a
    paper clip to open the door;  I updated
    to Sevice Pak 2 recently, but I am not sure if this has anything to cause this
    problem:  Please Help, anyone!
    Thanks

    Hi,
    Follow the procedure on the link below to create a bootable Ubuntu CD and follow the steps in Part 3 to 'Try it' to see if this OS will run from the CD without the need to install on your HDD.  This will show whether the problem is with Windows or a Hardware problem with the optical drive.
    http://www.ubuntu.com/desktop/get-ubuntu/download
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • When i plug my iphone in to my laptop it does not show up in devices

    i have tried to plug my iphone in to my laptop and download a memo.  however, my iphone does not show up in the devices.  any thoughts on the glich?

    PrinceKavin wrote:
    I need help to fix my iphone 5. i recently plug in my iphone 5 into the computer and tried to play music on youtube, or websites it does not play anysounds....
    Perhaps you need to spend a little bit of time here...
    iPhone User Guide (For iOS 6 Software)

  • IPhone does not show up as device, unless.....

    My iPhone often does not show up as a device in iTunes (Mac version) unless I turn wifi off, then back on.  When I do this, he iPhone appears as a device.  My iPad always shows up as a device.  It's only the iPhone that's a problem. 

    Occassionally if a picture is saved from an email, an MMS or copied from a website, it has had the tendency to create an error when trying to import the pictures from the camera roll. If that is the case on phone "B", then it is suggested that you email the offfending photos and then delete them from the camera roll. Once that is done, most will then appear in Windows. Not sure if this is the case for you, but that is generally the first fix.

  • Iphone 3GS does not show as iTunes Device

    I've followed all instructions and the troubleshooter and my Iphone 3GS still does not show in Itunes 10.5 on my Macbook Pro with Lion installed.  Any suggestions?

    I tried a different cable and the iphone now shows up so I believe my cable had failed. Hope this is help to others troubleshooting a similar problem.

Maybe you are looking for