R11 and tablespace issue

Hi hussein;
I want to hear your advice about R11 and tablespace issue... I am following :Subject: Oracle Applications Tablespace Model FAQs Doc ID: 269293.1
I can understand which tablespace using for what in R11 but i wonder one thing. Picture this please:
My AOOS_TS_TX_IDX tablaspace has 6 datafile as a_txn_ind06.dbf ... some of this file has %83 usegae 2 of %97 and %96... The quesiton is when we should resize datafile? I mean when we should say " oo the datafile is %?? using so i have to resize it.
One other question is my APPS_UNDOTS1 tablespace's datafile(those are 3 files) are now %100.. Should i resize them or its unncessarry?
Thanks for advice

Hi,
The quesiton is when we should resize datafile? I mean when we should say " oo the datafile is %?? using so i have to resize it.There is no specific answer to this question, and it depends on how this tablespace is utilized and on the size of the tablespace (for example, 70% used space of 1 GB tablespace is different that 70% used space of 100 MB tablespace). So, I would say whenever you believe you need to add more space to the this tablespace (these datafiles).
One other question is my APPS_UNDOTS1 tablespace's datafile(those are 3 files) are now %100.. Should i resize them or its unncessarry?You do not have to -- See (Note: 413732.1 - Full UNDO Tablespace In 10gR2) for details.
Regards,
Hussein

Similar Messages

Tablespace and performance issue

Hi,
I have Tablespace X and tablespace Y.
I have seven transaction tables in X, which has image tables in Y. X tablespace is my Online tablespace and Y my archive tablespace and I use the archive tablespace to store old data.
I use the same algorithm, only wrapped up in two processes, with only the source and destination alternating. The code performs extremely well for moving data X->Y. And ridiculously slow for Y-> X.
I have just started doing this process of archiving, so the data volume in both the sets of tables are the almost the same.
Any clue on what I could check up for here ?? What should be the problem ??
The trace file shows the similar plans both sides, only there are wait times in process Y->X.
Thanks for your time on this.
Ashok.

ahhh ... you are talking now about "internal" (vs. "external"?) volume instances. This implies probably you have really to talk to the responsible dba, as Justin already proposed.
One small correction, you always can do an "insert /*+ append */ ...". As Oracle will write into new datablocks then, you only would loose the last allocated free blocks. But in the case of the offline tables, this is not a problem as you only add data anyway therefore you'll not loose a lot. And disk space is not really a concern anymore these days.
For the other way around, you only had to do an "alter table X move tablespace <online-tbs>" afterwards to clean up all the unused blocks.
For the truncating, may be you can think about it again. You have a processing going on there ie there is some grouping/selecting criteria. Probably one of these criterias is a partitioning candidate? And with a partitioned table you would be back in the truncating game.
For the "I'm not let to DDL on the objects from inside the code" seems a rather funny restriction, as this doesn't let you do a truncate and instead you need a lot of (probably unnecessary) undo-tablespace for a delete. But as some dba's don't really know, what the job of a good developer is, you can probably ask your dba for a packaged procedure, where this table/partition gets truncated.

Sysaux tablespace issue

hi,
I ve upgraded an database for 9i to 10g. The upgrade was sucessfull and the Db was in normal usage. Due to some functionality testing the database was restored to a state from the backup taken after upgrade. But while restoring the database i forgot to include the path of the datafile of sysaux tablespace in the control file re-creation script.
I didnt notice this issue for long time until i realised the mistake made by me.
I found in the alert logs which showed errors such as
ORA-01157: cannot identify/lock data file 124 - see DBWR trace file
ORA-01110: data file 124: '/oracle/ora/dbs/MISSING00141'
ORA-27037: unable to obtain file status
since the path of the sysaux tablespace was not referred in the script i thought of referring it now and i issued the following command
alter tablespace sysaux add datafile '<path>/sysaux01.dbf' reuse;
i issed this as the datafile was already present and i thought of jus reuing it again.
But what had happened is this datafile had been added as an additional datafile for the sysaux tablespace,which means the sysaux is still referring '/oracle/ora/dbs/MISSING00141' as one of the datafile.
but one important thing is that there isnt any such datafile ie '/oracle/ora/dbs/MISSING00141' when i checked inside the dbs folder.
The path is getting referred as part of the sysaux tablespace but its physical location is not found.
So i did took this datafile offlinedrop issuing
alter database datafile '/oracle/ora/dbs/MISSING00141' ofline drop
but the problem i m facing now is the AWR is not opening up and it throw error stating first datafile of sysaux tablespace '/oracle/ora/dbs/MISSING00141' not found.
ORA-00376: file 124 cannot be read at this time
ORA-01110: data file 141: '/oracle/ora/dbs/MISSING00141'
ORA-06512: at line 21.
any solution for solving the problem would be appreciated
thanks,
ahmed

i m able to start up the database normally....there isnt any errors while starting the DB.These errors are encountered in alert log file and user trace files.As as result AWR is not opening.

Sysaux tablespace issue-missing sysux datafile

hi,
I ve upgraded an database for 9i to 10g. The upgrade was sucessfull and the Db was in normal usage. Due to some functionality testing the database was restored to a state from the backup taken after upgrade. But while restoring the database i forgot to include the path of the datafile of sysaux tablespace in the control file re-creation script.
I didnt notice this issue for long time until i realised the mistake made by me.
I found in the alert logs which showed errors such as
ORA-01157: cannot identify/lock data file 124 - see DBWR trace file
ORA-01110: data file 124: '/oracle/ora/dbs/MISSING00141'
ORA-27037: unable to obtain file status
since the path of the sysaux tablespace was not referred in the script i thought of referring it now and i issued the following command
alter tablespace sysaux add datafile '<path>/sysaux01.dbf' reuse;
i issued this as the datafile was already present and i thought of jus reusing it again.
But what had happened is this datafile had been added as an additional datafile for the sysaux tablespace,which means the sysaux is still referring '/oracle/ora/dbs/MISSING00141' as one of the datafile.
but one important thing is that there isnt any such datafile ie '/oracle/ora/dbs/MISSING00141' when i checked inside the dbs folder.
The path is getting referred as part of the sysaux tablespace but its physical location is not found.
So i did took this datafile offlinedrop issuing
alter database datafile '/oracle/ora/dbs/MISSING00141' ofline drop
but the problem i m facing now is the AWR is not opening up and it throw error stating first datafile of sysaux tablespace '/oracle/ora/dbs/MISSING00141' not found.
ORA-00376: file 124 cannot be read at this time
ORA-01110: data file 141: '/oracle/ora/dbs/MISSING00141'
ORA-06512: at line 21.
any solution for solving the problem would be appreciated
thanks,
ahmed

Hi, I've got exactly the same problem up to the point where I try to offline drop the MISSING0009 datafile.
The command says it completed OK but the phantom datafile does not go and still reports that it's there in dba_data_files, althoguh the online_status is RECOVER, the status is ONLINE.
I'm not sure how to get rid of the entry if the offline drop command doesnt work. I've tried recreating the control file and deleting the entry for this datafile too but somehow it returned after that too!
I''m also not sure what to do when I do get rid of it - since I cant recover the old sysaux01.dbf datafile since it's not consistent with the database since there has been a week inbetween and we're not running archivelogging.
I would assume that all the stuff usually put in the SYSAUX tablespace is therefore lost, but I dont think we use anything that normally puts stuff in there, I've only noticed this since I was trying to install em.
Do I have to rebuild the database from scratch? Or any ideas on how I can recover the situation? Can I do something like startup upgrade and re-run the upgrade scripts which will put their stuff back into sysaux....?
Many thanks for ideas
Rob

Oracle Tablespace issue

Hi,
I am having problem with one of our tablespace. I receive a error message saying unable to extent tablespace very often, even though we have enough space in tablespace, And i also observerd that max(bytes) in dba_free_Space is decreasing everyday. We have oracle 11g and tablespaces are locally manged with ASSM.
Space in our tablespace is as follows:
TSName Tot_Size Tot_free PCT_free Max_Free Chunk_Free
User 44,746,932,224 3,656,908,800 8 1,966,080 4,668
I get the above result when i execute the following query:
select a.tablespace_name,sum(a.tots) Tot_Size,
sum(a.sumb) Tot_Free,
sum(a.sumb)*100/sum(a.tots) Pct_Free,
sum(a.largest) Max_Free,sum(a.chunks) Chunks_Free
from
select tablespace_name,0 tots,sum(bytes) sumb,
max(bytes) largest,count(*) chunks
from dba_free_space a
group by tablespace_name
union
select tablespace_name,sum(bytes) tots,0,0,0 from
dba_data_files
group by tablespace_name) a
group by a.tablespace_name;
Why is the Max_free very less and it keep decreasing daily. I tried to shrink tables and rebuild indexes to gain some space , nothing helped. Can anyone help me if i am missing anything here ? And also please let me know if you need more information
Thanks for your time.

I have read the SAP notes suggested by Alpesh and Harleen. I spoke to the Database admin regarding the following tables for re-organization:
Tables: VIRSA_CC_ACTVL
            VIRSA_CC_BKGINP
            VIRSA_CC_JOBHST
            VIRSA_CC_PRMVL
            VIRSA_CC_SCHEDULER
            VIRSA_CC_THREAD
He said that it will save around 4Gb only.
Can you tell me if by setting the following thing in CC>Config>"Additional Options"
Enable Offline Risk Analysis   - No
Will we be able to save up space? Our main concern is not to increase further the size because of cost issues. We already increased the size twice earlier. The system was designed as per the sizing guidelines earlier. Thhanks both.
Thanks for your reply Sudip as well...We will configure automatic addition of tablespace soon after we resolve this issue....
Regards,
Venkateswara Rao

TABLESPACE Issue with DEV_SOAINFRA

Hi,
I am getting the following error while using the function ora:readBinaryFromFile
ORA-01691: unable to extend lob segment DEV_SOAINFRA.SYS_LOB0000147944C00002$$ by 8192 in tablespace DEV_SOAINFRA.
I know that automatic extending of DEV_SOAINFRA tablespace in em or purging of old instance data will resolve the issue, but is there any other way where I can get rid of storing instance data in SOAINFRA. This is because, I get large amount of size files through FTP adapter and they are getting into dehydration store. Is there any way I can get rid of this so that I wont be storing this data.

Thanks for your response,
1. in Step 1 i am using FTP adapter for copying from source directory to target directory in a single invoke ( i.e. file gets copied from remote location A to local location A) in a single invoke and I have used the following type in <interaction-spec className="oracle.tip.adapter.ftp.outbound.FTPIoInteractionSpec"> jca file.
2. After this I am invoking an webservice adapter which takes the files from local location to remote location B. The elements inside the WSDL are filename, filepath and file content. For file content i am using ora:readBinaryfromfile(). Also, I attached MTOM policy for WS adapter. Everything is working fine, but i am getting tablespace issue frequently as the attachments are getting stored in Attachment table of SOAINFRA.
Thanks,

Failed Hardware Scan and other issues E440

Hi all,
This is probably more rant than anything, but I wanted to give a heads up to others too.
I have a ThinkPad E440 that is a year old. From the very first time I turned it on, there have been issues. The first hardware scan (via Lenovo Solution Center - LSC) showed a warning for the Intel Dual Band Wireless-AC 7260 Local Connection Test. There were also tons of System Events that always show up in the "Configuration History" part of the LSC. You can look at the calendar and tell exactly which days I used the computer because there will be System Events generated each day. Things like app crashes and failed drivers.
In July 2014, I got the first warning for the 16 GB SSD - the SMART Short Self-Test. By February this year it showed as failed for each hardware scan (these were initially set up to run monthly).
Also the whole time I've had it the touch screen would just stop working at some point and I would have to reboot to get it working again.
I finally called Lenovo on March 30th, before my warranty expired. When I called that time, I didn't realize the hard drive failure was the SSD. So they sent me a new 500 GB drive. I also added the other things into the case when I talked to them. For the wireless issue they suggested making sure the driver was up to date. I did this and let them know when I called back that it was up to date and still having the warning. So I called them to tell them to tell them about the wireless and also that I realized it was the SSD having the failure, not the main drive. The first case had already been closed even though none of the other items were addressed.
So they opened another case (this is #2). They said to mail them the laptop since the wireless issue would probably be on the board and it wasn't something I could fix myself. They sent a box with a prepaid overnight shipping label. I was very sick for a few days so I sent it back to them on April 10th (a Friday). Via UPS I saw it was delivered on Saturday. Work was performed on it Monday, April 13th and sent back to me that very day. I received it on April 14th. This part of the service has been excellent - very fast response.
Being in IT, I included a letter with the laptop that outlined the issues that should have been in the case. I also printed the hardware scans and what the system events looked like.
When I got the laptop back, the sheet inside said they had replaced the Speaker because of Distorted Sound. This was not even on the list even though I had noticed it. I didn't even power up the laptop before calling them again - yes, I was furious! Plus our power was out...
So this was noon on the 14th. They opened case #3 and sent me ANOTHER BOX so I could send it back.
After our power came back on the 15th, I powered up my laptop. I opened the browser (I have it set to restore the previous session) and there was a sexually explicit video on YouTube. I opened the other browser and there was a different video on YouTube. So this person was watching YouTube instead of fixing my laptop. I looked through both browser histories and there was quite a bit of activity while my laptop was at the repair center... I ran the hardware scan - still failed and a warning for the wireless. They really hadn't done anything.
I also found two pictures of the repair person in the recycle bin...
So I called back. I was LIVID! They opened another case (this is #4). And sent me ANOTHER BOX. I finally learned the other day that once a case is opened, it cannot be edited or added to at all. Instead, they close the other case and open a new one. I guess their turnaround time for closing cases is excellent! I've never seen a system like that - and I've used a lot of them.
I got a really nice, patient fellow on the line. He took all my info (again). I emailed him the pictures, screen captures of the YouTube videos, the letter I had sent - everything. He entered as much into the new case as he could - he talked to one of the supervisors to make sure he did it right. Somehow he flagged it so that the laptop would get more attention (time) at the repair facility. He also opened a separate case (an escalation ticket?) for a supervisor to call me regarding the person's conduct at the repair facility. He said they would call me that day. (It's now the 25th and I've never heard from anyone)
So, he sent me ANOTHER BOX. I've built up quite a stack of them.
Our power was out AGAIN from the 17th through the 19th (don't get me started).
I noticed a hardware scan had now gotten a failure on the main hard drive. So I called them on the 21st to add this to the case before sending the laptop back. The girl said they can't add anything to an existing case or edit it at all once it's opened. She would have to open a new case and SEND ME ANOTHER BOX. I told her to forget it because I was ready to send it in and didn't want to wait for another box. I also asked for a status on that "escalation case" where the supervisor was supposed to call me. In order to do this she, yes, wait for it, had to open ANOTHER CASE!! So they would know I wanted a status. I'm completely dumbfounded.
So I sent it back on the 21st. This time I practically wiped it. I had already removed all my files the last time, but I had left my bookmarks and browser history intact. I set up a guest logon with admin privileges. I updated my letter and printed off more stuff to include with the box. On one sheet I had only the case number, the serial number and machine type. On another sheet I had "DO NOT SEPARATE THIS PAPERWORK FROM THE LAPTOP" and the case number. I put this sheet on top (The guy on the 15th said my letter and stuff may have gotten separated from the laptop once it was delivered to the repair facility). I used a ton of staples so it would all stay together. I included in my letter the failure on the main hard drive and asked if they could look at it. I wrote about having to open a new case if I wanted to include it.
They received it on the 22nd. A nice gentleman from the repair facility called me that day asking about the password. that. was. written. on the sheet they have you fill out. I told him what happened last time and also mentioned the hard drive failure and asked if he could look into it. He said they would.
I received my laptop back yesterday morning.The sheet that came with it said they had "replaced the following parts to complete the repair of your laptop."
Part Description                                           Symptom
IMAGE                                                             Replaced due to engineering change
System board                                                 Network card error
Hard disk drive                                                Network card error
ECA-WIRELESS                                            <no symptom listed>
There was also a sheet saying they had installed a factory preload of software and I needed to install Lenovo and Windows updates.
When I booted it up, the first thing I noticed, in the lower right corner was:
Windows 8.1
SecureBoot isn’t configured correctly
Build 9600
I ran a hardware scan. Well, I tried. It stopped part way through and said it finished successfully but most of the tasks showed up as cancelled. I tried to run it again - issues - rebooting ensued. It said the LSC wasn’t available and that I should try again or reboot.
Tried several times. Then got what I guess is the new BSOD - kinder, gentler:
Your PC ran into a problem and needs to restart. We're just
collecting some error info, and then we'll restart for you. (xx% complete)
If you'd like to know more, you can search online later for this error: DRIVER_CORRUPTED_EXPOOL
Even though the LSC said my Lenovo files were all up to date, I ran the Update. And first I had to download a new version of Update. Then I downloaded all of the Lenovo updates and installed them (there were quite a few). The BIOS update failed. While I was doing the Lenovo downloads, I got a light blue screen but no text (I was out of the room so I'm not sure what happened). Did CTRL-ALT-DEL and it shows only IE and Task Manager as applications that are running. Could not “Switch to” IE. Hitting window key to go to start didn't do anything. So I had to restart.
By 3pm yesterday there were 34 system events in the configuration history.
I ran the hardware scan again after I updated the Lenovo files, and you guessed it! Failure on the SSD (SMART Short Self-Test) and warning on the wireless. Nothing had changed. Except hardware scan is acting different than it did before I sent in the laptop for repairs. When it finishes, it instantly closes and just shows 100% complete. When I click on "see last results" it shows a screen called
Log Information,
Canceled 04/24/2015 n:nn pm
You have not done a hardware test on your computer
And the calendar in LSC only shows the very first hardware scan I did on Friday. Even the hardware scan screen shows the date and time of the last scan. It also shows the error code. In order to see exactly what is failing, I have to sit there and watch it very closely and snap a picture of the screen as soon as the error (or warning) shows up.
When I would try to run Windows update, it would hang up PC Settings. I couldn't even kill it using task manager because it didn't show up as a task. During this, I got a flag saying the firewall wasn't turned on. I tried to turn it on, but clicking on Turn on Windows Firewall didn't do anything. I tried to setup my Microsoft account but that just hung too.
I ended up running Windows Update FOUR TIMES to get all the updates installed. Every time I ran it, it said "Done!" and I would run it again and more would show up. The last time was this morning.
At some point, the error about SecureBoot went away.
Then, I created a bootable BIOS update disk. Following the ReadMe instructions, I went through ThinkPad Setup and verified several values. Of note:
Secure Boot was DISABLED. According to the ReadMe file, this should be ENABLED in Windows 8.1. I enabled it.
Under Startup/Boot, according to the ReadMe that came with the BIOS update, UEFI/Legacy Boot is supposed to be set at UEFI Only for Windows 8.1. Mine was set to "Both". I changed it.
In Startup, OS Optimized Defaults was DISABLED, even though it says right there (and in the BIOS update ReadMe) it should be ENABLED to meet Microsoft Windows 8 Certification Requirement.
After these updates, I flashed the new BIOS.
Then, I ran hardware scan again...
Now I have TWO failures on the SSD: Random Seek Test and SMART Short Self-Test. Great.
In the Event Viewer (that I recently discovered), it says my disk has a bad block. It just says The device, \Device\Harddisk\DR1, has a bad block. I assume this is the SSD...
There are 867 events in the event viewer - Critical, Error, and Warning...
Fifty-two of these are from October 7, 2013 - before my little laptop was a glimmer.
The rest are from when Lenovo had it and yesterday and today.
64 of them are the disk error.
341 are from DeviceSetupManager. 65 of those are from failed driver installs. 69 are for not being able to establish a connection to the windows update service. 64 are from not being able to establish a connection to the Windows Metadata and Internet Services (WMIS).
3 times it's rebooted without cleanly shutting down
60 of them are from Service Control Manager and say The TDKLIB service failed to start due to the following error: The system cannot find the file specified.
One of them says {Registry Hive Recovered} Registry hive (file): '\??\C:\Users\Default\NTUSER.DAT' was corrupted and it has been recovered. Some data might have been lost.
16 are warnings that various processors in Group 0 are being limited by system firmware.
12 say the certificate for local system with thumbprint <bunch of hex numbers> is about to expire or already expired.
108 are warnings for failure to load the driver \Driver\WUDFRd for various devices
16 are application errors
One is for the computer rebooting from a "bug check"
15 are for name resolutions timing out after none of the configured DNS servers responded.
10 are for SecureBoot being disabled.
14 for services terminating unexpectedly
15 are for WLAN Extensibility Module has stopped
61 are for applications not being able to be restarted because the application SID does not match Conductor SID
12 are for activation of CLSID timing out waiting for the service wuauserv to stop
So, I'll call them on Monday and open. a. new. case (#5?) - but really 7. And get A NEW BOX.
I'll keep you updated!

Hi amycdero and welcome to the HP Forum,
I understand that you are having scanning and printing issues after upgrading to Mavericks OS X v10.9.1. I will try my best to help you resolve this issue.
In this document for Mac OS X: Scanning Software Does Not Open or Stops Responding are steps the may help you with your scanning issue.
This document for Fixing Ink Streaks, Faded Prints, and Other Common Print Quality Problems should help with the streaking printing issue.
I hope this information is helpful. Please let me know.
Thank you,
I worked on behalf of HP.

Battery, heat, and ringer issues

I recently purchased the Iphone 4s.. this is my first iphone
I did the update that Apple sent out to help the battery and it seems like it worse then before the update?? My phone has been off the charger for 45 minutes, I sent 1 text message, and had 1 phone call. The percentage is now at 87. It the last 2 minutes i have watched it go down 2%? Is this normal? Also, the phone gets REALLY hot...
If not, what do I do now??
Also, I keep missing phone calls because I don't hear the phone ring... but the ringer is all the way up..
Any help will be greatly appreciated!!

mdorling wrote:
We've got the same issues, the BBM contacts went, now the BB won't charge ... we've tried all ways to get it to charge ... typically it's just over a month old so we can't get a full refund ... we are on here trying to find out what we need to do as we can't obtain a telephone number for BB customer services nor an email address only a tweet address which I haven't downloaded onto my handset. So am stuck!!! Any and all advice very gratefully received as seriously peeved with BB models now. My first BB was fantastic ... but all newer models have had problems ... think BB needs to ensure that all techy problems are fully ironed out prior to launching their new BB handset!
1. Connect your Z10 to the wall outlet charger for an hour and then with the Z10 powered on, and with it STILL CONNECTED, remove the battery for a minute and replace. This will normally reset the the on-device battery meter and allow the charging status and percentage to show more correctly.
2. Orange is your tech support contact and any issue which they cannot resolve, they should escalate up to BlackBerry tier two tech support, or you should ask/demand that.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

New Airport Extreme and iPhone Issues

I've had the networking day from ****. I previously had a 3rd Gen Time Capsule at our restaurant, connected to a Cisco 26port gigabit POE switch and Comcast digital voice and internet. Over the past few days, employees have reported trouble accessing the the Wifi network. After several restarts and firmware upgrades (including the dreaded "firmware problem" to fine update), nothing worked. I changed channels, back to auto, back to specific channels, back to auto. Made open guest networks. Nothing worked consistently. My iPhone might connect and my friend's might not. Nor his laptop consistently. Our Axis network cameras might take a bit extra time to connect. All quite random and quite frustrating.
So I swap out an older Airport Extreme (4th gen I believe) using the same configuration as the TC (Time Capsule). It works fine, except for the last port not working as expected. No matter, I plug the mac mini into the Cisco switch and off we go. Nevertheless, I'm still told we are suffering random Wifi issues. So I buy a brand new AE (5th gen) today to replace that one. Should work like a charm I thought. Right....
Several hours later, I finally have the new AE working, but only after doing several hard resets/factory restores, the works. For some reason, the mac mini could not successfully update any of the connected AEs - whether connected directly into the same AE, or if the Mini was connected to the switch. Nothing worked. Every time I tried to update the AE, it would hang and force me to unplug and plug it back in. It would also never save setting changes. I finally resorted to a friend's macbook to be able to restore it successfully. And once that worked, the mini was able to update the AE flawlessly. Our Point of Sales (POS) machines connect fine, our cameras connect fine, wifi printer connects, and the mini connects, and everything has internet.
Except my iPhone 5. Of course. It gets a signal fine (full bars). It gets an IP address. But I can't surf the web. Or download email. Or iMessages. Anything. No internet access. I try hard restarts on my iphone. I try assigning IP addresses by MAC address. I try resetting the AE. I try renaming the WiFi name. Nothing. I can make a guest network that works (on a different IP table, btw - 172, not 192.) But other than that, no access. Grrrr.
So I have a "working" AE router where some devices successfully connect (through wifi and ethernet) and some dont' (wifi iPhone). My iPhone connects fine to my home TC. So shouldn't be anything to do with that. But I'm at a loss. I'm going to go back and restore everything and power cycle everything tonight or tomorrow night. I don't know if that will help, but it's worth a try. Lord knows it feels like I've tried everything else.
Anyone have any good ideas of where to start besides voodoo dolls and baseball bats?

I took mine back, because I was having these very same issues. We use contivity too. I was able to connect only to one of three of the servers we manage (in Europe). I couldn't connect to the servers in Asia or here in the USA.
Replaced the Airport Extreme with my trusty old d-link 624, and no issues connecting to any of the three hubs.
Otherwise, I liked the Airport Extreme, and I'll consider buying it again when and if they address this VPN issue. I work at home so its obviously a "deal breaker" for me.

IQ826t Restart and Heating Issue

One thing I definitely do not like the HP's support especially when they will not allow us to buy a 7 Upgrade from Vista nor will they support something (even when I find their glitches and they admit after telling me it was just the OS).. On Repair work, I had to ship it out and this will be my 2-3 time to do repair on this PC in the past 3 years (and I have to wait a week for the repair to be done...)
Besides that, IQ826t, Win 7 Ultimate SP1
All Drivers are up to date with HP website (utilizing Win 7 64 bit drivers and Firmware is up to date). AVG update/scan (no issue - confirmed even rootkit).. Malwarebyte - Scan and no issue
Disk Cleanup, Disk Defragmentation done on a monthly and quarterly schedule
Biggest Issue:
I am getting a crash with Win 7 0x124 Stop Error Message (happens periodically and even after a reboot)
Never had this issue until May and the upgrade to Win 7 was done last year with SP1 update done on March (so it is not an issue with the OS as HP support personnel seems to think... I proved them the issue with Windows Update History, The Bluescreen error code on my error code reader).. This machine under warranty and I had issues with it constant (even in Vista)
They state that it is the OS.. Again, if that was the case, I would think it would happen right away like my Toshiba on SP1 upgrade... That was not the case in the matter. I have a firmware reset (default settings) and the issue persist..
The Error Code relates always HAL.dll or ntoskrnl.exe
One if hardware compatiblity and the other is an OS kernel exe file.. And this usually checking knowledge base relates to hardware failing due to 1) Compatibility (which HP website confirms is not the case) 2) OS corruption (which is not the case checking on safe mode and this happening STILL 3) Heat Issue (which I believe is the issue and was been documented on the Internet
What I am noticing is the unit is extremely HOT (vent is almost burning when it has been off and just turned on).. I wonder if the hardware pieces are literally melting to destruction since I can't just open it up (they state it will void my warranty)
The Symptoms before the Crash (happens any time.. Even right after a power up)
If you are playing audio or video, you will start to hear jitters and sound seems to echo itself .. Video would start to lag and become choppy.. Systems start to slow down and things seem to run very slow.. I have seen the power light on the PC start on but the touchscreen just go black (will not restart sometimes)..
Minor Issues (but could be related)
1) When running PC Hardware Diagnostic, they will come up with an error code in the past and that was warranted for a motherboard replacement (of course, they ship the box to the wrong location and I was in the middle of my wedding so I get to it now).. It was pertaining to PCI Express Status ICH9 PCI Express Root Port where it will generate an error code... Now, running the diagnostic... I will not get any error but PCI Express Root Port 3 & 5 do not show up on the diagnostic... Wouldn't that obvious show something that is a problem when there are 6 ports (which on the previous diagnostic that I can't grab past logs shows that). That is not warranted for a warranty work? Just a note, I got the fail test code (which was intermittent but keep happening and the tech support would not look at previous case.. Port 4 failed and a fatal device code)
2) Blu-Ray player will not run and their answer is that it is your Blu-Ray until they realize that I ran it on 3 different Blu-Ray player standalone, different Blu-Ray, and confirm DVD will work.. They still think it is a software issue until they can't deny my point when it will not read the Blu-Ray no matter what (they took control and confirmed it).. They believe the HP SmartDVD software was failing because of Win 7 and not Vista (even when I downgrade and confirm it works, I stated the software is the issue... Lone and behold, 2 months later they had an update that they refuse to admit I was RIGHT on the matter and done 15 hours of troubleshooting that they were wrong about)
3) Wireless Keyboard and Mouse lost connectivity even if the battery is not low... Just stop typing or omit letters.. This is considering the keyboard is literally in front of the touchscreen
4) Touchscreen is sensitive when it wants to be but won't in other... Constant issues there
This is why I have so much issue with support.. They seem to show that they will do anything to deny the issue.. Heck, I am a computer technian calling on the issue.. It ain't like I didn't troubleshoot on the matter... But they think we are all morons and when I prove them wrong, they will use any excuse to honor warranty... That is why it is amazing..

Look in your Settings > App Manager.
Tap Device Monitor.
Tap the Battery tab.
At the upper right, tap "Since Last Charge" to change to "Last 48 Hours".
What apps or processes are consuming the most battery power?
ALSO, in setting up your new Z30, are you syncing many contacts or calendar data from a connected email account?
Social accounts such as Facebook or Twitter?
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Just updated to IOS 7 and two issues: First when I connect my iPhone to my computer I get this error message:itunes was unable to provider data from sync services".

Just updated to IOS 7 and two issues:
First when I connect my iPhone to my computer I get this error message:itunes was unable to provider data from sync services". I'm not sure what this really means...
The second issue is when I try to select "Manually Manage Music"
The iPhone "My iPhone" is synced with another iTunes libary on "MY-PC". Do you want to erase this iPhone and sync with this iTunes library? An iPhone can be synced with only one iTunes library at a time. Erasing and syncing replaces the contents of this iPhone with the contents of this iTunes library."
So... I don't want to do that, but I do what to be able to Manage my music. I'm not sure what it means by being synced to another iTunes unless it means to an older version of itunes?
Anyone have any ideas?

I cannot address the sync services error right now, but the error that you receive when you change from sync to manually manage music is what happens when you change. Once you change to manually manage music, it erases all of the music and will only put the music that you want on the phone, content that you manually drag over to it. See if this support document helps you out. http://support.apple.com/kb/HT1535

PO number and material issued against this PO for subcontracting

How to know the link in between the PO number and material issued against this PO for subcontracting.
I have checked that PO history is not getting updated.
Thanks,

Hi,
We have 2 different scenarios where you can post a goods issue to Subcontract Venodrs.
Scenarios 1: You can post the goods issue against a subcontrac vendor with out referencing the Subcon PO from ME2O, at this stage we will be knowing what is the stock at subcontract vendor but we will not be knowing the issues against which and how much Quantities are posted.
So when we are post goods receipt, then we will come to know the consuption quantities.
Scenario: 2, If we use the delivery concept then we can track the goods issues against the subcon POs.
If you really keen to track the material issued to Subcon vendor against a PO so better use with delivery.
Thansk,
Satya.

Memory and No. of Processor calculation for Oracle EBS R11 and R12

Can some one please tell me …. How to calculate required Memory and No. of Processors for Oracle EBS R11 and R12.
For example we have 50 Concurrent users and 100 named (i.e. the users which are doing only Data entry.), so how to How to calculate required Memory and No. of Processors
Please guide me on the same.
Thanks,

Please refer to the following links, it may be helpful:
Oracle Applications Benchmark White Papers
http://www.oracle.com/apps_benchmark/html/white-papers-e-business.html
Oracle Applications Standard Benchmark White Papers
http://www.oracle.com/apps_benchmark/html/white-papers.html
Hardware requirements for Oracle APPS
Hardware requirements for Oracle APPS

Is it possible to use the same OSSO/OID for multiple R11 and R12 instances?

Hello guru's,
We have multiple R11and R12 instances that should be configured for Oracle SSO 10.1.4.3. For OID, we are still trying to decide between OID 10.1.4.3, or OID 11g. OAM is not an option because we also also need OSSO integration with Siteminder. We will also need to SSO-enable Discoverer an Forms.
I have successfully configured SSO for a single-instance EBS R12, but not for multiple instances, let alone include R11 and other components into the mix.
Do you have any special tips, guidance or lessons learned when SSO-enabling multiple instances into the same SSO/OID?
Thanks!
Maria

Interestingly, the article talks about using the same SSO/OID for EBS, JD Edwards, Peoplesoft multiple R11 instances, but did not mention 'multiple EBS versions'. Am I just being picky or there was a reason for it not being mentioned?In Steven Chan blog (in the same link), see the following:
Comprehensive Single Sign-On Solution+
If you have one or more E-Business Suite Release 11i instances and are tired of maintaining users separately for each environment, you can create a central OracleAS 10g environment and manage all 11i users in one place.
If you have a combination of PeopleSoft, JD Edwards, and the E-Business Suite in your organization, you can use OracleAS 10g to manage users for all three environments centrally.
If you have a combination of the E-Business Suite and custom applications based on Oracle databases or OracleAS 10g technology, you can use OracleAS 10g to manage users for all applications in a single place.
Thanks,
Hussein

OS 10.4.10 Update Causing Audio Popping (AND HUM) Issues:

OS 10.4.10 Update Causing Audio Popping (AND HUM) Issues:
The problem on my Intel Mac mini with external Klipsch speakers (two mid-range/high and a subwoofer) is REAL obvious as the system emits a hum like a Spinal Tap amplifier turned up to #11 when 10.4.10 powers down the audio circuitry
Then, if I play a song in iTunes, it first pops and the hum disappears right before playing.
Quite annoying. I restored the mini from a recent backup to 10.4.9. Problem gone.
I'm glad I test updates on the mini before applying them to my Intel iMac 24. I guess I'll just hide & watch what happens before doing any more updates.
Here's what I sent to Apple tech support:
Guys/Gals (OS X Engineers):
Concerning the Snap, Crackle Pop Audio problem in the 10.4.10 update:
Please. Just do the right thing and fix the audio.
There is no need to power cycle the audio subsystem to save .0005 amps on the laptop line.
And then to make your Mac mini/iMac/other desktop users have to put up with it when using AC power is ridiculous.
Put the audio subsystem back like it was in 10.4.9 and let the laptop battery freaks looking for mini-amp savings get a "work-a-round".
Crikey!
iMac 2.16 Ghz Intel Core 2 Duo 2GB RAM Mac OS X (10.4.9) 20 Years of Microsoft-Induced Grey Hair
Mac Mini 1.83 Ghz Intel Core Duo 1GB RAM Mac OS X (10.4.9) 20 Years of Microsoft-Induced Grey Hair

Libby,
Backup is unable to make a restorable by Disk Utility backup. You can restore pieces of the software as outlined in my FAQ about backing up user data:
http://www.macmaps.com/backup.html
But to be able to restore a backup with Disk Utility, you need a cloning utility to have made the backup.
I suggest starting a new thread here, where someone else could help you out better:
http://discussions.apple.com/forum.jspa?forumID=752&start=0
First off, you'll get a wider audience who may be able to solve your problem. Secondly, responses to you won't confuse the original poster with solutions that don't apply to them. And thirdly, you'll know for certain whether or not a response applies to you.

R11 and tablespace issue

Similar Messages

Maybe you are looking for