R25desm gives rep-3000 error

Hi,
I am trying to start reports2.5 in UNIX and I am using r25desm to start the report. It gives me rep-3000 error. Can anyone help on this?
Thanks
null

You might want to check if NLS_LANG and DISPLAY environment variables are set before
you start the designer session.
Mine is set as follows:
NLS_LANG=American_America.WE8ISO8859P1
DISPLAY=my_ip_address:0
Hope this helps.
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by dron:
Hi,
I am trying to start reports2.5 in UNIX and I am using r25desm to start the report. It gives me rep-3000 error. Can anyone help on this?
Thanks<HR></BLOCKQUOTE>
null

Similar Messages

REP-3000 Error Message

I have install Web Reports Server 6i on Solaris 2.8 x_86 platform and i hav configure its above documentation. I can start it under OAS 4.0.7 web listener. Then, if i want to create the test report on the web, i receive an error message:
REP-3000: Internal error starting Oracle Toolkit.
Tell me please, what can i do.

You may be right. But in this case i don't know another plase, there nls-support (*.nlb) files are may be installd. In my $ORACLE_HOME there are no directory, naming like datad2k. I think, that Developer 2k use nls-support files from base nls directory, because i install if after RDBMS, but after installation of Developer 2k in the list of installed products i so, that it content the 8.0.6 NLS-Support Files and Libraris. I in the firm belief that it is not RDBMS files, becouse the version of RDBMS is 8.0.5.
It meens, that the cause of REP-3000 error is other. If you know some more about it, tell me please.
null

REP-3000 Error Urgent!!!

Hi, When I running report on Oracle 9iAs Rel2, I Receive REP-3000 error.
My Platform Info. : Linux Advanced server 2.1
I can run xclock on my linux box;
I Set NLS_Lang="SIMLIFIED CHINESE_CHINA.ZHS16GBK" in reports.sh
when I comment the NLS_LANG=.... in my reports.sh, I have not receive this error msg, But I can not see any chinese character, I only can see "????"
How to solve this problem?
Thank you very much !

My Platform Info. : Linux Advanced server 2.1I assume you mean Red Hat Linux Advance Server 2.1. There are too many Linuxes out there, so it's hard to tell without the vendor name.
I can run xclock on my linux box;Why does running xclock successfully always have to be the test? :-))
(Don't take me seriously, for I have no better suggestions)
I Set NLS_Lang="SIMLIFIED CHINESE_CHINA.ZHS16GBK" in
reports.sh
when I comment the NLS_LANG=.... in my reports.sh, I
have not receive this error msg, But I can not see
any chinese character, I only can see "????"I've noticed a few problems with NLS_LANG and rwservlet. Can you explain how you're running the report. What is the input, and whether you're using rwclient, rwservlet, rwrun, etc.? Also, if you could post the relevant portion of the server and engine trace files (<server></server>.trc and <server></server>-rwEng-0.trc).
-Manish

Reports: REP-0177 & REP-3000 errors :-( (RH 6.2.2 HA 1.0)

Hi Folks, hi Oracle,
we have some serious problems here with Oracle Reports 6i Patch 6 which is running under Red Hat HA (Red Hat 6.2.2 High Aviability Server 1.0, based on Zoot)
Because HA installs without X i have installed all needed X-packes to get a X11 system, and it runs fine.
Then i set up request for a reports from the console i get the following message:
[oracle@webserver1-do bin]$ ./rwcli60 REPORT=xxxx.rdf USERID=xxxxx/xxxxx@xxxx SERVER=xxxxx DESTYPE=SYSOUT DESFORMAT=PDF benu_id=x masszeile=xxx
REP-0177: Error while running in remote server
REP-3000: Internal error starting Oracle Toolkit.
REP-3000: Internal error starting Oracle Toolkit.
If i change the DISPLAY to a faked adress, i become the 111-errors (cant connect to X11-Socket), so i think the repserver connects to X but have some other problems with X.
If i change DISPLAY to an another Linux-Server with fully installed X11 & KDE, the report runs fine.
And all the same if the call the report over apache.
I have read the Bug-Info about Bug 1108326, but i have the same, if i change the format to HTML.
Any suggestions?
H.-C.G|rsoy
null

hello,
be aware, that you have to set the display in the environtment of the server (meaning the startup-script of the server).
regards,
the oracle reports team

REP-3000 error after installing OAS 10.1.2.0.2

Hello All,
I've searched the forum and it looks like REP-3000 is a common error encountered when DISPLAY or NLS_LANG aren't set up properly. However, my variables are setup properly. I can run xclock without any problem.
This is after a brand new installation of OAS v10.1.2.0.2 (only forms and reports services). I already had the rdbms software installed v10.2 on my AIX server. I've installed OAS in another ORACLE_HOME.
After the installation, i tried to run the demonstrations....The forms services is ok but not the reports services. I know the variables are set properly but not sure what else to try. I've updated scripts like report.sh and rwrun.sh to add the DISPLAY variable there. I've also altered the opmn.xml file per some other documentation but to no avail.
Has anyone done this Forms and Reports Services installation on AIX or any non-windows server?
Thanks.

I checked the Metalink note# 264159.1 (I am setting the paramform=no when calling the report) as indicated in this document. Bug#3442598 status is "Fixed in 10.1.2.0.2" in Metalink. Is this might be another bug ?
FS, thank you for replying but using a table does not seem to be as a viable option - it is against the idea of dynamically striping the where clause on the form side. I have no problem passing individual parameter or group of parameters from forms to reports. This only happens if I dynamically strip the where clause from the system.last_query and pass it to the report. I don't know how to decipher the dynamically stripped where clause and parse it into individual values (parameters) that I can pass into the report. I just want to pass the where clause of the last executed query to the report. If we can not do it, what is the point of dynamically striping the last query. You mention putting the values into a table, can you please elaborate how should I parse the where clause that form generates (should be dynamic) into a table? The selected columns in each query can be different each time the users execute a custom query. This is why I don't think this table method you suggested will work. Maybe I am wrong. Have you done this before? Have you dynamically parsed a dynamically stripped forms query into table/s ? Any working example is really appreaciated.
I did not understand the length of the URL ? the P_WC user variable on the report side is 2000 characters long - more than sufficient to hold the where clause. What is the limit on the URL length? The error message shows the entire where clause with added %22 and %20 's - therefore I don't think the URL length is an issue here. But I maybe wrong. If the URL length is an issue, then the error message is ambiguous.
Thank you.

GraphicAntialiasing="true" gives REP-0606 error

Hi Friends,
When i am using graphicAntialiasing="true" to make lines in my graphs smooth it gives me Rep-0606 error.
I am using reports 9.2.0.4.0. Is enviorment variable REPORTS_GRAPH_IMAGE_DPI available with this version of reports.
Thanks in advance
Regards
Kamal

Kamal,
I would assume that REPORTS_GRAPH_IMAGE_DPI is available with your version. I am running Reports Builder 9.0.4.0.33 and it is available with my version. Be sure to restart your Reports Builder after making any changes to the REPORTS_GRAPH_IMAGE_DPI environment variable. I didn't think it was working yesterday, because I changed the variable while Reports Builder was still open, but my report graphs improved dramatically after closing and restarting Reports Builder.
graphicAntialiasing="true" did not give me an error, but did not improve the graphics output as much as the REPORTS_GRAPH_IMAGE_DPI setting. I took the Antialiasing parameter out again.
Andrew

Reports Server: REP-3000

Hi all,
I have the following system setup:
OS: SuSE SLES-7 Linux
Kernel: 2.4.7-64GB-SMP
Memory: 1GB RAM
SWAP: 2GB
When I try to run the test report on the "Getting Started with Oracle9i Reports" I get the following error in a new Browser Window:
- Error
REP-3000: Internal error starting Oracle Toolkit.
REP-3000: Internal error starting Oracle Toolkit.
I don't want to use the standard X server. I decided to use Xvfb.
I performed the following steps:
- Shutdown of Oracle9iASr2, according to metalink note: 200475.1 (oracle)
- $ emctl stop
- $ webcachectl stop
- $ dcmctl shutdown
After that the 9iASr2 instance was sucessfully halted.
- Shutdown the standard X server which was running on display number 0 (root)
- Start Xfvb as root, according metalink note: 208745.1 (root)
- $ nohup /usr/bin/X11/Xvfb :50 -screen 0 1024x800x8 -pn -fp /usr/lib/X11/fonts/misc -sp /etc/X11/xserver/SecurityPolicy &
- $ DISPLAY=$(hostname):50.0; export DISPLAY
- $ /usr/X11R6/bin/xhost +
I also tested to execute the command xclock and I got no error.
- 9iASr2 config changes (oracle)
- Changed DISPLAY variable in .profile to the new value
- $ORACLE_HOME/bin/reports.sh
- DISPLAY=lindi:50; export DISPLAY
- $ORACLE_HOME/opmn/conf/opmn.xml
- <prop name="DISPLAY" value="localhost:50.0"/>
- This entry is in the OC4J_BI_Forms config tag. is that correct?
- Startup 9iASr2 (oracle)
- $ emctl start
- Connect to OEM and started the whole instance. All processed were sucessfull started
- I was able to connect to OEM, this means the Xvfb Frame Buffer is setup correctly otherwise I would not be able to connect to the EnterpriseManager. Is that correct?
- I was able to check the failed jobs in the reports server. That means the report server is running.
- I was able to run my forms application.
- I open the "Getting Started with Oracle9i Reports" page in a browser and got the error decribed above.
To me it seems that there has to be another DISPLAY variable I did not set correctly. Because when I start another X server with the user oracle on display 0 then I'm able to run the report sucessfully. But I don't want to start the standard X server, because then I need access to the console, and I not always have access to it.
Does anybody know what that could be and help me,
thanks
Oliver

Try the solution provided in the Release Notes Addendum section 5.10.15 (Component issues)
Anyway I am providing the notes here.
5.10.15 Reports in-process server gives REP-3000 error when running report
When running a sample report using the report in-process server, an error message
like the following can appear in the browser:
REP-3000: Internal error starting Oracle Toolkit.
REP-3000: Internal error starting Oracle Toolkit.
Use the following sample URL to test for this error message using the appropriate
hostname, domainname, port and two_task entries:
http://hostname.domainname:port/reports/rwservlet?report=test.rdf&userid=scott/t
iger@two_task&destype=cache&desformat=htmlcss
If the REP-3000 error message appears, the display is not set correctly. When
running a report server from the command line, the environment variable DISPLAY
setting is used. However, the reports in-process server uses the following
configuration file for the display setting:
$ORACLE_HOME/j2ee/OC4J_BI_Forms/config/oc4j.properties
The default display entry is as follows:
oracle.display=:0.0
On some servers, there might not be an X server running on :0.0 or this entry
might not be resolved correctly. In such cases, change the display setting to a
machine where an X server is present and can be accessed by this server.
To test whether an X server is running on given machine and you have permissions
to connect to it, you can use the following command:
xterm -display myserver:0.0
If you do not have permissions to access the display or if there is no such display
running on the given machine, an error similar to the following is displayed:
Xlib: connection to "myserver:0.0" refused by server
Xlib: Client is not authorized to connect to Server
xterm Xt error: Can't open display: myserver:0.0
Once you have identified a machine with a valid X server, or started the display on
the server machine being used, you can change the default entry to the new display.
For example to use the X server running on myserver:0.0 we would change the
default entry to:
oracle.display=myserver:0.0
After these changes are completed, it is necessary to restart the Forms/Reports oc4j
instance with the following commands:
$ cd $ORACLE_HOME/opmn/bin
$ ./opmnctl stopproc type=oc4j instancename=oc4j_bi_forms
$ ./opmnctl startproc type=oc4j instancename=oc4j_bi_forms
You can now test the sample URL again to make sure that the in-process server
works correctly. When using the sample URL, the sample test.rdf report should
be displayed in the browser.

REP-3000: An internal error occured starting Oracle Toolkit Solaris 10 SPARC

I am running WL 10.3.6.0 with Forms/Reports 11.1.2.1.0 on a Solaris SPARC 10 64-bit box, specifically a T4.
Brand new install of Solaris 10 with only Forms/Reports installed as the user "oracle".
When I run rwbuilder.sh I get the dreaded REP-3000 error. I currently have an SR opened with Oracle but its taking forever and I've scoured the net for many different fixes which do not work. Forms Builder does work fine however.
Some things I have checked and/or changes I have made:
DISPLAY - set properly. I use ReflectionsX to get to my server, I can run xclock also, I've even tried xhost+.
I've tried running rwbuilder.sh direct at the console to make sure its not a ReflectionsX issue, same error.
NLS_LANG=AMERICAN_AMERICA.WE8ISO8859P1
I've done an ldd on "rwbuilder" to make sure the binary's dependencies were met, all fulfilled with no problems.
Updated reports.sh:
REPORTS_DEFAULT_DISPLAY=NO
DISPLAY=(updated with my direct IP:0.0)
Relinked reports builder.
At this point I'm stumped. Anyone actually have Reports Builder working on a Solaris 10 SPARC box or am I poineering this? LOL

REPORTS_DEFAULT_DISPLAY=NO is correct on AIX
Take a look at http://download-uk.oracle.com/docs/html/B14048_02/pbr_rfap.htm#sthref3930
To revert to the dependency on DISPLAY and use screen fonts (old font look up algorithm):
* Set REPORTS_DEFAULT_DISPLAY=NO
* Remove the screenprinter.ppd entry in the uiscreenprint.txt file.
* Set the DISPLAY variable to the active X-Windows display surface.
Regards,
Martin

Error --REP-3000: Internal error starting Oracle Toolkit.

Hi
While submitting the concurrent request (active user) im getting error if i submit the active responsibilities
its completed successfully i have set display also still im getting error.
Xlib: connection to "omega:0.0" refused by server
Xlib: Client is not authorized to connect to Server
Xlib: connection to "omega:0.0" refused by server
Xlib: Client is not authorized to connect to Server
REP-3000: Internal error starting Oracle Toolkit.
REP-3000: Internal error starting Oracle Toolkit.

Please verify the DISPLAY on the server as follows:
- Issue "xhost +" as root user
- Issue "xclock" as applmgr user --> Make sure you can display the clock
If the above does not work, please set the DISPLAY properly in the application context file and run AutoConfig.
More details can be found in the following note:
Note: 200474.1 - Comprehensive REP-3000 Troubleshooting and Overview Guide
https://metalink.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=200474.1

Parameter Form not calling the Main report - Gives REP-0110, REP-1070, REP-0110 error

I am using run_report_object to call a report in which the user has to input some paramters. I have followed the instructions as in the Oracle White paper document on Forms/Reports integration.
The paramter report does come up but when I hit the submit button, I get an error
REP-0110: Unable to open file 'rclug005'.
REP-1070: Error while opening or saving a document.
REP-0110: Unable to open file 'rclug005
I've checked the privileges and everything's fine on that front. Also, I can get to open the report with the web.show document built-in with paramform setting = No.
I am guessing something's wrong with the html constructed in the parameter form which is,
<form method=post action="http://myserver/dev60cgi/RWCGI60.EXE?">
<input name="hidden_run_parameters" type=hidden value="server=myserver &report=rclug005&destype=Cache&desformat=html&userid=uid/pwd@test">
In the Report Before Form trigger, I've copied the foll. html code from the Oracle White paper,
vc_parameter_form :=
'<html><body bgclor="ffffff"><form method=post action="'||:p_action||'">'||
'<input name="hidden_run_parameters" type=hidden
value= "'||vc_hidden_runtime_values||'">'||'<center><p>
<table border=0 cellspacing=0 cellpadding=0><tr><td>
<input type=submit></td><td> width=15
<td><input type=reset></td></tr></table><p><hr></p>';
I've set the :p_action parameter to a value of http://myserver/dev60cgi/RWCGI60.EXE?
Also, In the end of the report before form trigger I added this
srw.set_before_form_html(srw.text_escape, vc_parameter_form);
Any help/tips is appreciated & Thanks.

Thanks Danny,
I am building the variable exactly as in the White paper in the "before form" trigger using exactly the same values give there.
vc_hidden_runtime_values := 'server='||:p_servername||'&report='||vc_report_name||'.rep&destype='||:destype||'&desformat='||:desformat||'&userid='||:p_userinfo;
My report has some extra parameters too it expects. So do I have to include the names of those parameters too in the string above?
For example, in my report a user parameter is named 'print_date', which I do see and populate with value in the parameter form, then do I have to build that in the vc_hidden_runtime_values string above.
I am using Report 6.0.8.11.3 on 9iAS.

Error REP-3000 with parameter BATCH=NO in rwconverter

Hi all:
So we compile our modules in unix environment with this kind of sentence for reports.
$ORACLE_HOME/bin/rwconverter.sh userid=sintesis/[email protected] batch=yes source=$fichcompilar stype=rdffile dtype=repfile overwrite=yes
So we have the message in prompt...
Report Builder: Release 10.1.2.3.0 - Production on Mar Nov 8 10:15:21 2011
Copyright (c) 1982, 2005, Oracle. All rights reserved.
I've read in the documentation that If want to supress this message we have to change batch=yes to batch=no.
Changing batch=no makes the compilation fail retrieving Error REP-3000
We don't have to use Xserver.

Moderator Action:
This post was originally placed into the Oracle Linux sub-forum.
It does not appear to be a Linux issue.
It has been moved to the Reports forum, hopefully for closer topic alignment.

Postscript report fail - REP-3000: Internal error starting Oracle toolkit

Hi,
I am receiving the error REP-3000: Internal error starting Oracle Toolkit when I am running a conc. program with postscript as output. I changed Active Users program and tested it. It failed.
Metalink says DISPLAY issue. I ran the concurrent program - "Prints environment variable values" giving DISPLAY as variable. I received a value. like <hostname>:0.0
What could be the issue?
Release - 11.5.10.2
OS -Linux
Apache, Forms on 1 Node, Concurrent Manager on the second one.
Database - 10g R2 on Unix.
Thanks
Cherrish Vaidiyan
Edited by: Cherrish on Aug 19, 2010 5:01 PM

Hi Hussein,
Please find the complete concurrent program log:
Application Object Library: Version : 11.5.0
Copyright (c) 1979, 1999, Oracle Corporation. All rights reserved.
FNDSCURS module: Active Users
Current system time is 19-AUG-2010 15:34:33
+-----------------------------
| Starting concurrent program execution...
+-----------------------------
Current NLS_LANG and NLS_NUMERIC_CHARACTERS Environment Variables are :
American_America.WE8ISO8859P1
REP-3000: Internal error starting Oracle Toolkit.
REP-3000: Internal error starting Oracle Toolkit.
Report Builder: Release 6.0.8.28.0 - Production on Thu Aug 19 15:34:33 2010
(c) Copyright 1999 Oracle Corporation. All rights reserved.
Enter Username:
Start of log messages from FND_FILE
End of log messages from FND_FILE
Program exited with status 1
Concurrent Manager encountered an error while running Oracle*Report for your concurrent request 73686471.
Review your concurrent request log and/or report output file for more detailed information.
Executing request completion options...
Finished executing request completion options.
Concurrent request completed
Current system time is 19-AUG-2010 15:34:46
I will check the old forums too.
Thanks

REP-3000: Internal error starting Oracle Toolkit twice

Hi,
When I call reports from the web i get the
REP-3000: Internal error starting Oracle Toolkit
error message twice.
I am reading from the forum related to the same issue, everyone saying its related to environment variable DISPLAY.
DISPALY=localhost:12.0 is already set on Sun Solaris before starting the report60_server script to start/stop oracle 6i report server.
Through secure shell client, I logged on to the Solaris server and trying to stop and start the report6i server and trying to run the reports from the IE browser through Apache webserver.
Thanks in advance,
Usha

DISPALY=localhost:12.0 is already set on Sun SolarisSimply setting DISPLAY in the current shell won't help. The variable must be exported.
On csh:
setenv DISPLAY 'localhost:12.0'
On sh:
DISPLAY='localhost:12.0'
export DISPLAY
In either case, it can be verified:
env | grep DISPLAY
-Manish

REP-3000 Internal error starting Oracle Toolkit in oracle9ias

I want to use the Report Server included in my oracle9ias R2 installation (Business Intelligence and Forms) on Linux RH.
When I call a report from a browser, I get the message:
"REP-3000. Internal error starting Oracle Toolkit in oracle9ias".
XClock is working fine.
Somebody know what can I do?
Regards,
Sergio Castro

Hi Sergio,
You need the DISPLAY variable set on the system. Some servers don't have a graphic adapter.Install Xvfb on
your system. If you need more info please visit at
http://otn.oracle.com
under Products -> Oracle 9i Application Server ->
Utilities For Oracle9iAS -> X Virtual Frame Buffer(XVFB)

REP-3000: Internal error starting Oracle Toolkit in multinode environment

Dear All,
We are facing one issue with reports.
Breifing the environment:
Multinode 11.5.10.2 with 9.2.0.6 database on Solaris.
Node a: Database
Node b: Concurent+admin installed in /u02/applprod
Node c: web+forms installed in /u02/applprod
When we ran XML reports the reports are getting ending in "warning" status,
==========================================================
XML_REPORTS_XENVIRONMENT is :
/u02/applprod/prodora/8.0.6/guicommon6/tk60/admin/Tk2Motif_UTF8.rgb
XENVIRONMENT is set to /u02/applprod/prodora/8.0.6/guicommon6/tk60/admin/Tk2Motif_UTF8.rgb
Current NLS_LANG and NLS_NUMERIC_CHARACTERS Environment Variables are :
American_America.UTF8
REP-3000: Internal error starting Oracle Toolkit.
==================================
I have tried set
DISPLAY in user profile to <hostname>:0.0 in each node
and i tried setting the DISPLAY in
Node B(conc+admin):
========
adcmctl.sh
adrepctl.sh
gsmstart.sh
Node A(form+web)
============
gsmstart.sh
Still the error is repeating Please helpme out to rectify this error.
Thanks and Regards
Vasu

I have done xhost + through loging into server by VNC viewer.
and changed the DISPLAY in xml as "<hostname>:1.0" then ran autoconfig in conc+admin node, Then started application. now i am not getting the
"REP-3000: Internal error starting Oracle Toolkit " message in log but the log message shows as follows
SaleCo Custom Application: Version : UNKNOWN
Copyright (c) 1979, 1999, Oracle Corporation. All rights reserved.
XXAP_PAYVOUCHER module: SaleCo: Payment Voucher
Current system time is 02-JUL-2008 20:20:48
+-----------------------------
| Starting concurrent program execution...
+-----------------------------
Arguments
p_vendor_id='24'
p_check_id='10888'
Environment will now switch to UTF-8 code-set.
Parts of this log file may not display correctly
as a result. This is an expected behavior.
XML_REPORTS_XENVIRONMENT is :
/u02/applprod/prodora/8.0.6/guicommon6/tk60/admin/Tk2Motif_UTF8.rgb
XENVIRONMENT is set to /u02/applprod/prodora/8.0.6/guicommon6/tk60/admin/Tk2Motif_UTF8.rgb
Current NLS_LANG and NLS_NUMERIC_CHARACTERS Environment Variables are :
American_America.UTF8
Report Builder: Release 6.0.8.27.0 - Production on Wed Jul 2 20:20:49 2008
(c) Copyright 1999 Oracle Corporation. All rights reserved.
Enter Username:
Start of log messages from FND_FILE
End of log messages from FND_FILE
Executing request completion options...
------------- 1) PUBLISH -------------
Beginning post-processing of request 286677 on node APPS001 at 02-JUL-2008 20:20:50.
Post-processing of request 286677 failed at 02-JUL-2008 20:20:50 with the error message:
One or more post-processing actions failed. Consult the OPP service log for details.
------------- 2) PRINT -------------
Not printing the output of this request because post-processing failed.
Finished executing request completion options.
Concurrent request completed
Current system time is 02-JUL-2008 20:20:50
===================================
Please suggest..
Regards
Vasu

R25desm gives rep-3000 error

Similar Messages

Maybe you are looking for