R6870 setup

Please can you assist me with a proper manual and / or additional info.
My situation is as follows.
OS = fully up to date windows 7 32bit ultimate.
Motherboard = intel bad axe 2
Graphics card = R6870 2pm2digd5
Stage 1 – current = monitors are:
- a 27 inch Mecer 1920x1200 DVi connector,
- Samsung HDTV 1920x1080p HDMI connector (via cat 6 HDMI powered extender),
- Sansui HDTV HD ready ?x720 VGA connector
Stage 2 – will replace Mecer monitor with 3x 23” 1920x1080 monitors. (so since card will only handle 4 monitors will need a switch or splitter somewhere.
Stage 3 – will upgrade Sansui TV to full HD probably with HDMI connector.
So, now at stage 1, I have connected the Samsung to the HDMI port on the graphics card, and connected the VGA to the card via an DVI to VGA adapter plug, and the mecer to the card via DVI. Have tried the two DVI connectors both ways around (DVI and DVI-I sockets). However with both variants of connections there are problems. With Mecer in the DVI-I port, all 3 monitors are detected and I can set either the Mecer (desired) or the Samsung to the main monitor, but the other one is then completely off (while the sansui is enabled in both cases).
If I swap the Mecer to the DVI port and the sansui to the DVI-I port, ten only the mecer and the Samsung get detected and the snasui is not even detected.
So I need to know which ports to connect each monitor to for each of my 3 stages. There are simply too many combinations for me to try them all out by trial and error. Also I need to know what mini display port adapters to buy first.
Also, I need to know once I can get 4 monitors working whether I can use eyefinity for the 3 monitors and still have the two TV’s not part of the eyefinity group (or rather the one TV with a splitter or switch for the other), or whether I have to make them part of the eyefinity group as well which could be problematic? Or whether I can duplicate on of the 3 eyefinity monitors onto the tv/s which would be cool.
Cant believe such a well branded product is so sloppy in providing proper info on the product???!!!! Please can you try to help me to get the needed info.

maybe this can help you? http://www.amd.com/us/products/technologies/amd-eyefinity-technology/Pages/eyefinity.aspx

Similar Messages

R6870 Twin Frozr II for a 3 monitor setup

Building a new computer for my dad and was wanting to use just one vid card for 3 monitors, the system will be used for online stock trading where there will be a different application on each monitor and other use will be general stuff not much for gaming, this will be my first attempt with multiple monitors here are the main components,this computer will not be over clocked.
mb- msi p67a-gd53 [b3]
cpu- i5-2400
vid- msi r6870 twin frozr II 1gb 256bit
pws- corsair gs600 600w
mem- corsair vengeance 8gb [2x4gb] ddr3 1600 [pc3 12800] cmz8gx3m2a1600c9
hd- wd 500gb
monitors- LG e2340v
not even for sure how to hook the monitors up thanks

Here is an article that uses a 6870 card. Probably has the same output ports as yours.
They connected 3 monitors, all with DVI in connections.
http://icrontic.com/article/sapphire-radeon-hd-6870-review-triple-monitors-on-a-budget
No reason your connections shouldn't work the same.
You may have to get HDMI to VGA and/or DVI to VGA converters if your screens only have VGA in connectors.

MSI R6870 (2PM2DIGD5) dual-screen capabilities.

Good afternoon. I am having some issues with my graphics card, which I was hoping someone here could help out with.
I decided upon a new system a few days ago, and seeing how the R6870 is a very nice card for a very nice price I decided upon that one, also keeping in mind the option to expand later in life using Xfire. I've been building my own systems since I was 12 so naturally I decided upon that. Preferring to spend an hour assembling the system over waiting two weeks for someone else to get around to it.
The issue is as follows: DVI port 2 does *not* give off a signal (bottom one when the card is built in). Not even during bootup.
The setup:
Code: [Select]
MoBo: MSI G70A-G54
CPU: AMD Phenom II X6 (2.8Ghz)
GPU: MSI R6870 2PM2DIGD5
PS: Coolermaster SilentProM 700W
Both screens are connected with a dvi-vga adapter
The system is a clean install of Windows 7 Ultimate 64bit.
What I've tried:
1. I swapped the cables around. Whatever screen is on port 1 works flawlessly.
2. Updated the drivers.
3. Booted in safe mode.
4. Went to the shop and got myself a new graphics card (same type).
What I suspect:
1. The card is not capable of running two screens through a dvi-vga convertor? (would be pretty sad for a brand new card)
2. It needs to be connected to the power supply using seperate cables for both of it's connectors? Is it that big of a drain on power? Could this be the cause of my problems?
Is there anyone here that has had similar issues, or knows someone that had, and has a solution for me? All the shops are closed for now, but if this isn't fixed by monday I'm afraid I'm going to have to go for a different brand, this is getting really annoying.
Hoping for a quick reply,
-- M.

Not the perfect testing setup, but currently have the card running in a windows vista 64bit machine. It also has an MSI Mobo and a Phenom CPU. Just slightly older types.
I can get dual screen on this setup, but only if the second port is connected WITHOUT a dvi-vga convertor. Two VGA monitors still doesn't work which makes me think this is something that just doesn't work with this card.
The crashing problem could not be simulated.
I'm severely tempted to just exchange the graphics card for a different type, unless anyone has a better suggestion?

Problem with R6870 Twin Frozr II/OC in 32-bit mode

hi,
i have a R6870 Twin Frozr II/OC vga.
cpu : amd phenom ii x4 965
ram : 2x2gb geil 1333
main: msi 870a-g54
display : asus ve228h(full hd)
os: xp pro 32-bit
in 32-bit color mode and full hd resolution, when i work with iexplorer or notepad or ... and scroll the screen, the content becomes squared and Disassembled.
i tried to download the latest version of vga driver and install it,but problem didn't solve.
how can i solve this problem?
thanks.

my installed software are in the end of this message.
the first problem didnt solve!
again when i scroll screen in net explorer!
when i click on minimize icon of window to minimize it or click on tab of a minimized program in task bar, the mouse pointer stoped and when the work is done(the window is minimized or maximized),mouse can move!
is it a property of amd cpu's?
thanks
2007 Microsoft Office Suite Service Pack 1 (SP1)
AMD Processor Driver
AMD USB Filter Driver
ATI Catalyst Install Manager 3.0.800.0
ATI Problem Report Wizard 3.0.800.0
Adobe Flash Player 10 ActiveX
Adobe Flash Player 10 Plugin
Adobe Reader 9 new
Advertising Center
Ashampoo Internet Accelerator 2.00
Babylon
Babylon Toolbar
CCC Help Chinese Standard
CCC Help Chinese Traditional
CCC Help Czech
CCC Help Danish
CCC Help Dutch
CCC Help English
CCC Help Finnish
CCC Help French
CCC Help German
CCC Help Greek
CCC Help Hungarian
CCC Help Italian
CCC Help Japanese
CCC Help Korean
CCC Help Norwegian
CCC Help Polish
CCC Help Portuguese
CCC Help Russian
CCC Help Spanish
CCC Help Swedish
CCC Help Thai
CCC Help Turkish
Catalyst Control Center - Branding
Catalyst Control Center Graphics Previews Common
Catalyst Control Center InstallProxy
Catalyst Control Center Localization All
Google Talk (remove only)
Hotfix for Microsoft .NET Framework 3.5 SP1 (KB953595)
Hotfix for Windows XP (KB954550-v7) 7
ImagXpress
K-Lite Mega Codec Pack 6.7.0
MSI Afterburner 2.0.0
MSXML 6.0 Parser (KB933579) 6.10.1200.0
Microsoft .NET Framework 2.0 Service Pack 2 2.2.30729
Microsoft .NET Framework 3.0 Service Pack 2 3.2.30729
Microsoft .NET Framework 3.5 SP1
Microsoft Games for Windows - LIVE
Microsoft Games for Windows - LIVE Redistributable
Microsoft Office Access MUI (English) 2007
Microsoft Office Access Setup Metadata MUI (English) 2007
Microsoft Office Enterprise 2007
Microsoft Office Excel MUI (English) 2007
Microsoft Office Groove MUI (English) 2007
Microsoft Office Groove Setup Metadata MUI (English) 2007
Microsoft Office InfoPath MUI (English) 2007
Microsoft Office Office 64-bit Components 2007 12.0.6215.1000
Microsoft Office OneNote MUI (English) 2007
Microsoft Office Outlook MUI (English) 2007
Microsoft Office PowerPoint MUI (English) 2007
Microsoft Office Proof (English) 2007
Microsoft Office Proof (French) 2007
Microsoft Office Proof (Spanish) 2007
Microsoft Office Proofing (English) 2007
Microsoft Office Publisher MUI (English) 2007
Microsoft Office Shared 64-bit MUI (English) 2007 12.0.6215.1000
Microsoft Office Shared 64-bit Setup Metadata MUI (English) 2007 12.0.6215.1000
Microsoft Office Shared MUI (English) 2007
Microsoft Office Shared Setup Metadata MUI (English) 2007
Microsoft Office Word MUI (English) 2007
Microsoft Software Update for Web Folders (English) 12
Microsoft Text-to-Speech Engine 4.0 (English)
Microsoft Virtual PC 2007 SP1 6.0.192.0
Microsoft Visual C++ 2005 Redistributable
Microsoft Visual C++ 2008 Redistributable - x64 9.0.30729.4148 9.0.30729.4148
Mozilla Firefox 4.0 (x86 en-US)
NOD32 FiX v2.1
NOD32 antivirus system
NVIDIA PhysX
Nero 9 Essentials
Nero BurnRights
Nero BurnRights Help
Nero ControlCenter
Nero CoverDesigner
Nero CoverDesigner Help
Nero DiscSpeed
Nero DriveSpeed
Nero DriveSpeed Help
Nero Express Help
Nero InfoTool
Nero Installer
Nero Online Upgrade
Nero StartSmart
Nero StartSmart Help
NeroExpress
OpenAL
REALTEK GbE & FE Ethernet PCI-E NIC Driver
Rapture3D 2.3.22 Game
Realtek High Definition Audio Driver
Renesas Electronics USB 3.0 Host Controller Driver
SiSoftware Sandra Professional Home XII.SP2 14.20.2008.4
Skins
UltraISO Premium V9.36
WinRAR archiver
Windows Imaging Component 3.0.0.0
Windows XP 2010 (Farsi Fonts Pack Nastaliq Keyboard)
Yahoo! Messenger
ccc-core-static
ccc-utility64 2010.1118.508.9110
neroxml
ooVoo

How can I setup a mail-specific passcode/restriction on iPad used by multiple family members?

How can I setup a mail-specific passcode/restriction on iPad used by multiple family members?
Have an Exchange mail account setup and accessible in my mail on iPad... however my kids use it and i would like to restrict them from accessing this specific portion of the device. I tried viewing restriction options and do not see that i can apply a restriction specifically to Mail. Thanks for your help.

Not a feature of iOS. Check the AppStore to see if there are other
mail apps that allow passcode protection.
Or use Safari to log onto your email via a web-based interface and
enter your credentials each time. A bit slower, but the kids will
not know the details to login.

New setup questions...

Hey Guys,
I'm moving to a new condo on 9/1 and getting Fios (switching from cable) for the first time. In the proverbial nutshell, what I want to do is this: run two HD TiVos (with cablecards), plus my Apple Time Capsule as my primary router. I don't care a bit about VOD or Verizon's channel guides, email, or any other silly thing they provide. An ISP is (or ought to be) just a 'dumb pipe'.
Having done some research online today, it seems as though I need to have my ONT set up to run Ethernet, not MOCA (coax). Is there anything else I've missed that I need to know?
Thanks! Any suggestions greatly appreciated... :-)
Regards,
Ken

You would want to have a CAT5 Cable run from the location where the ONT will be to where your Apple Router will be locatated.
Allow the FIOS Technician to install their Router and get everything up and running. Since you are not planning on using the Verizon Router the location should not mater. I would just have a CAT5 Patch cable available and ask them to use it to make the data conenction from the ONT to the Verizon Router.
Once the technician is done you can release the TCP/IP Address from teh Verizon Router, Power Down, Swap in your Router, and hopefully be all setup. Here is a FAQ with more information on using different routers:
http://www.dslreports.com/faq/verizonfios/3.0_Networking
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it.
If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

I am trying to setup VPN with QuickVPN

Hi I am trying to setup VPN with WRVS4400N and Quick VPN on client side. I am fairly new to VPN and did some research and looked through the manual but can't seem to get it to work so far and from what I noticed many people are having this problem. So hopefully someone can tell what the problem is or at least point to right direction on solving this.
Basically it gives the "Failed to establish connection" generic error, shows it almost instantly..
It also showed the certificate error before but then I read about putting it in the installation directory and it stopped showing it, and whats strange is later I removed it but it doesnt show the error any longer, so don't know if its caching it somewhere or what can be going on...
In effort to look for answer and test things out I tried to connect to another location and setup a WRV200 router, I also get the same error but not instantly, it even shows "Activating Policy" but then doesn't go farther and shows the generic error...
Also with this setup strangly it always shows the certificate error, no matter if I put one in directory or not... Even tried to name it as the WRVS4400N certificate name...
Anyway VPN IPSec is disabled, and Client Accounts are configured and changed password several times to make sure its correct, VPN Passthrough enabled on all 3 options.
I tried to disable Windows Router, I also have a router in place do I possibly need to open some type of ports for the QuickVPN client?
Don't know yet whats going on if I am missing something or if there is some problem that needs work-around but if you know the answer or guesses of answer please let me know.

Hi Aleksandr,
since this question is about a product in the Cisco Small Business / Linksys range, I suggest you move it to the community, where you will have a better chance of getting expert advice.
best regards,
Herbert
Cisco Moderator

Add management server: Setup version: 7.0.9538.0 is not compatible with database version: 7.1.10226.0

I want to add another management server to our existing SCOM environment. But whenever I run this setup on a new server I get stuck in the window for selecting the OperationsManager database. The database field stays blank and in the OpsMgrSetupWizard log
there are lines that the setup version is not compatible with the database version. But I use the same installer as when I installed the other management servers a year ago.
Maybe there is a newer setup installer? But I can't find it.
[10:42:54]: Error:
:Error:setup version: 7.0.9538.0 is not compatible with database version: 7.1.10226.0
[10:42:54]: Info:
:Info:Using DB command timeout = 1800 seconds.
[10:42:54]: Info:
:Info:isOMDatabase: Read returned true. so far, this is OM DB, not an empty DB
[10:42:54]: Debug:
:Connection was not open. We will try to open it.
[10:42:54]: Debug:
:SqlConnectionReady returned True.
[10:42:54]: Info:
:Info:Using DB command timeout = 1800 seconds.
[10:42:54]: Info:
:Info:isOMDatabase: Read did not return true. The MG is missing. This is not OM DB
[10:42:54]: Info:
:Info:Using DB command timeout = 1800 seconds.
[10:42:54]: Always:
:Azman store table not found in OperationsManagerDW table, assuming this is an not a valid OMDB for empty DB scenario.
[10:42:54]: Info:
:Info:DatabaseConfigurationPage: DB connection attempt completed.
[10:42:54]: Info:
:Info:DatabaseConfigurationPage: DB connection attempt completed.

Never mind, found it!
Apparently there was a newer version of SCOM setup in msdn and someone upgraded our existing SCOM environment. Downloaded the new setup, new report viewer controls and a System
CLR Types for Microsoft® SQL Server® 2012 and now it works!!

Can we setup two sets different 7912 logos in one CCM cluster?

Hi,
CCM 4.1(3) cluster within head office. We created the 7912 logo for system default image. However, the remote site 7912 phones, need to use a different logo other than the head office.
as per http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=IP%20Telephony&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddc5d3d/0#selected_message
We can create the 7912 logo, but how can we setup two or more different 7912 logos for different sites?
We noticed on CCM4.1(3), there is idle URL for 7912 phone, what is the callmanager default link for this URL? I am thinking to use different logo file names, and put the related URL on this parameters for remote site 7912 phones.
Could someone let me know or any other better way to do?
Thanks,
JJ

Hi JJ,
This should work just the way you have described. Have a look;
Idle
Enter the URL that displays on the Cisco IP Phone display when the phone has not been used for the time that is specified in Idle Timer field. For example, you can display a logo on the LCD when the phone has not been used for 5 minutes.
Leave this field blank to accept the default setting.
Idle Timer (seconds)
Enter the time (in seconds) that you want to elapse before the URL that is specified in the Idle field displays.
Leave this field blank to accept the value of the Idle URL Timer enterprise parameter.
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00801ecfc7.html#1121361
Here how on CCM;
Method 1:
Choose System > Enterprise Parameters so that the change is propagated to all of the phones from the Cisco CallManager Administration page.
In the URL Idle field, enter http://IP_address_of_CallManager/CCMCIP/filename.xml.
In the URL Idle Time field, enter any positive value in seconds.
Method 2:
Choose Device > Phone under the Cisco IP Phone configuration so that only this phone displays the graphics from the Cisco CallManager Administrator page.
Choose the phone/phones on which you want to put the display.
In the Idle field, enter the path http://IP_address_of_CallManager/CCMCIP/filename.xml.
In the Idle Timer field, enter any positive value in seconds.
From this good doc;
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a00801c0764.shtml#topic4
Hope this helps!
Rob

HT4557 whats the best itunes/appleID setup for family of 3 with 3 ipads, 3 iphones, one PC with all music on. if we use 3 separate ones how do we share purchased and home content?

been with apple for years. one itunes/appleID in use for family - all purchases and downloads on the one account..
now got 3 ipads, 3 iphones and when we update the software, we seem to get text/facetime issues due to multiple email addresses and phone numbers for the different devices that each individual uses. For example, I send a text and it appears to have come from my wife or son to the recipient. Not good !
there seems to be direction from apple that each of us should use our own apple id, thogh how do I link the accounts so enable family sharing of music/media we have purchased etc - Id also like to be able to review and keep a private eye on what my son downloads as he is 11 yrs old ! I manage this currently as we allow him access to the password for itunes (as we all use the same id today)
Am i better setting up accounts for my wife and son independent of my own, or not. Each of us would like access to the family content we have and the master library of synced content. I just want the most simplistic approach that apple, or others would recommend.
Is there a better or optimum setup for a family as we cannot be alone.....

Thanks for the help, but a follow up question now.
My iPhone won't arrive for a little while, but my wife already got hers and she wants to set it up now. Using my Apple ID for the purchases, if she starts setting hers up, can she change her iCloud ID to something else quickly? It keeps telling us that we have to sign in with the AppleID first.
Should we just set up an iCloud account via normal internet before trying all this via iPhone?

MULTIPLE DEVICES SETUP IN ITUNES, SAME APPLE ID

We have one home computer (with Windows), and have 2 IPOD Touch's plus 1 IPAD all setup in ITUNES on this same computer. We are also setup with ICLOUD.
Kids IPOD's get music and FACETIME contacts all mixed up with each other and with the IPAD. What is the best way to keep each other's music/playlists as well as FACETIME contacts from syncing to each other's devices?

Please test after each of the following steps that you haven't already tried. Stop when the problem is resolved. Back up all data before making any changes. Keep in mind that no one here represents Apple or can help with customer-service issues.
Step 1
A purchased app can only be updated by signing in to the App Store with the same Apple ID that was originally used to buy it. There's no way around that limitation, which also applies to free apps. If you can't sign in with the buyer's ID, delete the app and reinstall it. You'll have to pay for it again, if applicable.
Step 2
If you get the alert when trying to update a bundled iLife app, select the Purchases page in the App Store and locate the app in your purchase history. If there's a button marked ACCEPT on the right, click it.
If you have a used Mac, the bundled apps were linked to the original owner's Apple ID and can't be transferred to you. Reportedly, customer service has issued redemption codes to some second owners who asked, but it's not guaranteed.
Step 3
If you're trying to update iLife or iWork apps that were installed from a purchased DVD, or if you have a refurbished Mac bought directly from Apple, contact App Store customer service for a redemption code. You may be asked for the part number of the DVD.
Step 4
From the App Store menu bar, select
Store ▹ View My Account
Enter your Apple ID password at the prompt. At the lower right corner of the window that opens, click the Reset button. Close the window.
Step 5
According to a report, the error can result from changing the language setting of your Apple ID account. I can't confirm.

How do I use family share to setup a new device for my child when I don't already have one with iOS 8?

My kids want apple products.
I don't own any.
I buy an iPad for one and an iPhone for the other, but I can't set them up because they require me to setup Family Share and create accounts. I can't do that because I don't have a device with iOS 8 already setup.
I do have a valid AppleID. I've had it for years. I use it with iTunes.
I wish they would just let me manage the account setup and Family Share through a web page. Right now I'm dead in the water and Christmas is approaching fast.

I have found a solution.
It turns out that all the documentation I could find on the web was wrong. At least in the case of the iPad I just bought. I did manage to borrow a device so that I could setup family share and the kids accounts, but when I went to enter the new existing account into the setup of the iPad, it then started leading me through the process to create the account (clearly it didn't bother to check if it really existed already). In reality, I believe had I just entered a "new ID" for my child, that didn't exist, it would have led me through the same process. As it was, I had to back out to the first screen and skip the creation process, since I had already created the IDs elsewhere.
The only part I'm not clear on, is if I still would first have needed to turn on family sharing for my ID before starting this whole process, or whether it would automate that while creating the child AppleID.

I need help with proper DNS setup for 10.5.8 Server

I'm administering a 10.5.8 server that I sold and setup about a year ago. I'm experiencing issues with getting iCal server to be happy. All of the clients are running 10.5.8, but I'm running 10.6.1. I've heard from others that connecting iCal in 10.6 to a 10.5 iCal Server should be no problem.
I'm beginning to think that I have DNS issues. Probably because I'm not and never have been 100% certain how to set it up completely correctly. I used to be able to get Kerberos tickets, but now I can't. With the new "Ticket Viewer" in 10.6, it asks for two bits of information. First is "Identity" where I'm guessing I should put [email protected] and then password. When I do this I get an alert dialog that says "Kerberos Error -- cannot resolve network address for KDC in realm example.com"
The server is a Mac Pro tower with two Ethernet ports. En2 is connected directly to the Internet and has a static IP with a domain name assigned to it. We'll call it "example.com" for the purposes of the discussion. The En1 is connected to the network switch and has a static LAN IP of 192.168.1.250. All clients inside and outside are able to reach the server via domain name for WWW & AFP, no problem.
nslookup on the static IP address returns "example.com" and nslookup on "example.com" returns the correct static IP address. Open Directory is running and happy including Kerberos. The LDAP search base is "dc=example,dc=com". The LDAP search base is a concept I haven't quite grasped, so I'm just going to assume it's correct.
The domain name is hosted outside by a service provider that forwards all "example.com" requests to the server with the exception of mail.
In DNS, I have three "sections" that look like this:
Name Type Value
1.168.192.in-addr.arpa. Reverse Zone -
192.168.1.250 Reverse Mapping example.com.
000.000.00.in-addr.arpa. Reverse Zone -
000.000.000.000 Reverse Mapping example.com.
com. Primary Zone -
mail.example.com. Alias mail.our-email-isp.com.
example.com. Machine Multiple values
www.example.com. Machine Multiple values
NOTE: the zeros aren't actually zeros, they are the static IP assigned to the server/domain
When I select the top element "1.168.192.in-addr.arpa." down below "Allows zone transfer" is NOT checked. Nameservers shows the zone as "1.168.192.in-addr.arpa." and the Nameserver Hostname as "ns.example.com."
When I select the next line down "192.168.1.250", Resolve 192.168.1.250 to: example.com.
When I select the "000.000.00.in-addr.arpa." element, it has the same settings -- nameservers "000.000.00.in-addr.arpa." and "ns.example.com."
When I select the next line down (our static IP), Resolve 000.000.000.000 to: example.com.
When I select "com." the admin email is populated with a valid email address, Allows zone transfer is NOT checked. In nameservers, Zone is "com." and Nameserver Hostname is "example.com." The mail exchangers are mail2.our-email-isp.com. priority 10 and mail.our-email-isp.com. and priority 20.
When I select the machine "example.com." it shows both the real-world static IP and the 192.168.1.250, same with "www.example.com.".
Am I doing something wrong with this setup? Should "com." be the primary zone or should that be "example.com." ???
I've been thinking about getting rid of the DNS entry for the 192.168.1.250 address altogether, but will the clients in the office suffer performance issues??? I do not think that the client workstations are configured to get DNS from the server anyway. Should the "www.example.com." record be a Machine record or should it be an alias record?
Any help you have to offer is greatly appreciated! Thanks!
In the meantime, I'm going to look around and see if I can understand "Allows zone transfer" and LDAP Search base a bit better.

Okay, I found a lovely article at the following address which I think helps me to clarify what I'm doing wrong. Despite that, I'd still like to have any feedback you have to offer.
http://www.makemacwork.com/configure-internal-dns-1.htm
Also, when editing DNS entries, Server Admin likes to set the nameserver to "ns." -- whatever your domain is. Should I be overriding that and if so, replace it with what?

IPad 2, restore & setup as new, then restore from backup?

Confused yet? I am!
So here we go, yes, I'm new to the forum, I've had my iPad 2 since Oct. 2011. And No, this problem isn't in my head.
Last week, I finally updated to iOS 5.1.1, and I deeply regret doing so. I had NO issue before the update, and now, my battery is garbage.
I used to be able to go 2 - 3 days before having to charge and that's with an average of 4 hours a day. Now, after just a few hours (5) I have to charge and it takes forever. I've been working with Apple, but they having given me an option I'm happy with.
1) Mail my unit back to them to switch out with a refurb. I am against this option as I like my unit. I didn't originally buy a refurb and I should have to accept one now. The screen on my unit is perfect, no bleed or dead pixels. I've taken immaculate care of mine and I'm afraid I'll get a unit I'm not happy with. Plus, it will be running iOS 6, which I'm not ready for.
Option two is...and this needs to be done whether I return my unit or not, is a restore and setup as new. Which means I would loose all my information buried deep within my apps. This would also install iOS 6 on my unit.
My question is this...
If I do a Restore, Setup as new, can I then go back in and do a restore from back up, to put all my stuff back in its place.
I'd love to hear from anyone that has any insight, suggestions, experience, or comments about this.
How did you handle it?
What was the outcome?
Did you involve Apple in the resolution?
Or,
Is it just not worth dealing with and I should just keep using it until it won't take a charge.
I know there have been a million posts about this, and I've read a lot of them, but I just haven't found a solution yet.
And before anyone states the obvious, ALL locations are off, all email accounts are set to manual, there are no notifications set.
In the past week, I've done 3 reset all settings, drained battery until system shut down, and did an uninterrupted full charge.
I've reset network settings. I make sure apps are closed by double tapping Home button, and done a hard reset by holding power button and home button until apple icon appears. I'm at a loss, and don't know what else to do.

First, make sure you are using the most current version of iTunes 11.1.3 (8). Second, what version of iOS 7 was your old phone running, i.e. 7.0, 7.0.1, 7.0.2? If your back-up was made with a version of iOS that is newer than the version on your new phone, it will not sync. For example, if your back-up was of a phone running iOS 7.0.4, and your new phone was running 7.0.2 out of the box, the back up will not sync to the new phone until it is updated to iOS 7.0.4.

Mail server setup issues

Hi.
I am in trouble setting up a basic mail server. I just spent the last 10 or so hours, in one more try to set it, and yet no results.
Please, give some help as i am becoming sort of desperated with it
This time, i followed this guide since the beginning.
What I've done:
- Created a user vmail, with home directory set on /var/mail/vmail/
- Had a LAMP server already working.
- Created two databases: postfix_db and roundcube_db, owned by postfix_user and roundcube_user respectively.
- Since it is for personal use and i don't use "old/odd clients like Outlook" i skipped smtps. And made the following files:
My postfix main.cf(every commented line removed):
queue_directory = /var/spool/postfix
command_directory = /usr/bin
daemon_directory = /usr/lib/postfix
data_directory = /var/lib/postfix
mail_owner = postfix
mydomain = mydomainname.tld
unknown_local_recipient_reject_code = 550
alias_maps = hash:/etc/postfix/aliases
alias_database = $alias_maps
debug_peer_level = 2
debugger_command =
PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin
ddd $daemon_directory/$process_name $process_id & sleep 5
sendmail_path = /usr/bin/sendmail
newaliases_path = /usr/bin/newaliases
mailq_path = /usr/bin/mailq
setgid_group = postdrop
html_directory = no
manpage_directory = /usr/share/man
sample_directory = /etc/postfix/sample
readme_directory = /usr/share/doc/postfix
inet_protocols = ipv4
relay_domains = *
virtual_alias_maps = proxy:mysql:/etc/postfix/virtual_alias_maps.cf
virtual_mailbox_domains = proxy:mysql:/etc/postfix/virtual_domains_maps.cf
virtual_mailbox_maps = proxy:mysql:/etc/postfix/virtual_mailbox_maps.cf
virtual_mailbox_base = /var/mail/vmail
virtual_mailbox_limit = 512000000
virtual_minimum_uid = 5000
virtual_transport = virtual
virtual_uid_maps = static:5000
virtual_gid_maps = static:5000
local_transport = virtual
local_recipient_maps = $virtual_mailbox_maps
transport_maps = hash:/etc/postfix/transport
smtpd_sasl_auth_enable = yes
smtpd_sasl_type = dovecot
smtpd_sasl_path = /var/run/dovecot/auth-client
smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination
smtpd_relay_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination
smtpd_sasl_security_options = noanonymous
smtpd_sasl_tls_security_options = $smtpd_sasl_security_options
smtpd_tls_auth_only = yes
smtpd_tls_cert_file = /etc/ssl/private/server.crt
smtpd_tls_key_file = /etc/ssl/private/server.key
smtpd_sasl_local_domain = $mydomain
broken_sasl_auth_clients = yes
smtpd_tls_loglevel = 1
Postfix master.cf
smtp inet n - n - - smtpd
submission inet n - n - - smtpd
-o smtpd_tls_security_level=encrypt
-o smtpd_sasl_auth_enable=yes
pickup unix n - n 60 1 pickup
cleanup unix n - n - 0 cleanup
qmgr unix n - n 300 1 qmgr
tlsmgr unix - - n 1000? 1 tlsmgr
rewrite unix - - n - - trivial-rewrite
bounce unix - - n - 0 bounce
defer unix - - n - 0 bounce
trace unix - - n - 0 bounce
verify unix - - n - 1 verify
flush unix n - n 1000? 0 flush
proxymap unix - - n - - proxymap
proxywrite unix - - n - 1 proxymap
smtp unix - - n - - smtp
relay unix - - n - - smtp
showq unix n - n - - showq
error unix - - n - - error
retry unix - - n - - error
discard unix - - n - - discard
local unix - n n - - local
virtual unix - n n - - virtual
lmtp unix - - n - - lmtp
anvil unix - - n - 1 anvil
scache unix - - n - 1 scache
/etc/postfix/virtual_alias_maps.cf (sample password)
user = postfix_user
password = m/<~VN4XQ!G=jE[A/-
hosts = localhost
dbname = postfix_db
query = SELECT goto FROM alias WHERE address='%s' AND active = true
/etc/postfix/virtual_domains_maps.cf
user = postfix_user
password = m/<~VN4XQ!G=jE[A/-
hosts = localhost
dbname = postfix_db
query = SELECT domain FROM domain WHERE domain='%s' AND backupmx = false AND active = true
/etc/postfix/virtual_mailbox_limits.cf
user = postfix_user
password = m/<~VN4XQ!G=jE[A/-
hosts = localhost
dbname = postfix_db
query = SELECT quota FROM mailbox WHERE username='%s'
/etc/postfix/virtual_mailbox_maps.cf
user = postfix_user
password = m/<~VN4XQ!G=jE[A/-
hosts = localhost
dbname = postfix_db
query = SELECT maildir FROM mailbox WHERE username='%s' AND active = true
- Created the SSL key with no problem, and put it in place.
Edited dovecot.conf:
protocols = imap pop3
auth_mechanisms = plain
passdb {
driver = sql
args = /etc/dovecot/dovecot-sql.conf
userdb sql {
driver = sql
args = /etc/dovecot/dovecot-sql.conf
service auth {
unix_listener auth-client {
group = postfix
mode = 0660
user = postfix
user = root
mail_home = /var/mail/vmail/%d/%u
mail_location = maildir:~
ssl_cert = </etc/ssl/private/server.crt
ssl_key = </etc/ssl/private/server.key
dict {
#quota = mysql:/etc/dovecot/dovecot-dict-sql.conf.ext
#expire = sqlite:/etc/dovecot/dovecot-dict-sql.conf.ext
!include conf.d/*.conf
!include_try local.conf
/etc/dovecot/dovecot-sql.conf
driver = mysql
connect = host=localhost dbname=postfix_db user=postfix_user password=m/<~VN4XQ!G=jE[A/-
default_pass_scheme = MD5-CRYPT
user_query = SELECT '/var/mail/vmail/%d/%u' as home, 'maildir:/var/mail/vmail/%d/%u' as mail, 5000 AS uid, 5000 AS gid, concat('dirsize:storage=', quota) AS quota FROM mailbox WHERE username = '%u' AND active = '1'
password_query = SELECT username as user, password, '/var/mail/vmail/%d/%u' as userdb_home, 'maildir:/var/mail/vmail/%d/%u' as userdb_mail, 5000 as userdb_uid, 5000 as userdb_gid FROM mailbox WHERE username = '%u' AND active = '1'
- Installed postfixadmin and roundcube and made their apache alias.
- Made directories writable for them.
/etc/webapps/postfixadmin/config.inc.php (note that there is no "?>" to end the script, it came just like that, and since it had no error there ill assume its normal)
<?php
$CONF['configured'] = true;
$CONF['setup_password'] = '562bc24a874b0c2a7340e3da04b3fdf6:d60282f5cbc19340c73cafbb6526379be696a7c7';
$CONF['postfix_admin_url'] = '[url]http://mydomain.com/postfixadmin[/url]';
$CONF['postfix_admin_path'] = dirname(__FILE__);
$CONF['default_language'] = 'en';
$CONF['database_prefix'] = '';
$CONF['database_tables'] = array (
'admin' => 'admin',
'alias' => 'alias',
'alias_domain' => 'alias_domain',
'config' => 'config',
'domain' => 'domain',
'domain_admins' => 'domain_admins',
'fetchmail' => 'fetchmail',
'log' => 'log',
'mailbox' => 'mailbox',
'vacation' => 'vacation',
'vacation_notification' => 'vacation_notification',
'quota' => 'quota',
'quota2' => 'quota2',
$CONF['admin_email'] = '[email protected]';
$CONF['smtp_server'] = 'localhost';
$CONF['smtp_port'] = '25';
$CONF['encrypt'] = 'md5crypt';
$CONF['authlib_default_flavor'] = 'md5raw';
$CONF['dovecotpw'] = "/usr/sbin/dovecotpw";
$CONF['min_password_length'] = 5;
$CONF['generate_password'] = 'NO';
$CONF['show_password'] = 'NO';
$CONF['page_size'] = '10';
$CONF['default_aliases'] = array (
'abuse' => '[email protected]',
'hostmaster' => '[email protected]',
'postmaster' => '[email protected]',
'webmaster' => '[email protected]'
$CONF['domain_path'] = 'NO';
$CONF['domain_in_mailbox'] = 'YES';
$CONF['maildir_name_hook'] = 'NO';
$CONF['aliases'] = '10';
$CONF['mailboxes'] = '10';
$CONF['maxquota'] = '10';
$CONF['quota'] = 'NO';
$CONF['quota_multiplier'] = '1024000';
$CONF['transport'] = 'NO';
$CONF['transport_options'] = array (
'virtual', // for virtual accounts
'local', // for system accounts
'relay' // for backup mx
$CONF['transport_default'] = 'virtual';
$CONF['vacation'] = 'NO';
$CONF['vacation_domain'] = 'autoreply.change-this-to-your.domain.tld';
$CONF['vacation_control'] ='YES';
$CONF['vacation_control_admin'] = 'YES';
$CONF['alias_control'] = 'NO';
$CONF['alias_control_admin'] = 'NO';
$CONF['special_alias_control'] = 'NO';
$CONF['alias_goto_limit'] = '0';
$CONF['alias_domain'] = 'YES';
$CONF['backup'] = 'YES';
$CONF['sendmail'] = 'YES';
$CONF['logging'] = 'YES';
$CONF['fetchmail'] = 'YES';
$CONF['fetchmail_extra_options'] = 'NO';
$CONF['show_header_text'] = 'NO';
$CONF['header_text'] = ':: Postfix Admin ::';
$CONF['user_footer_link'] = "[url]http://mydomain.com[/url]";
$CONF['show_footer_text'] = 'YES';
$CONF['footer_text'] = 'Return to mydomain.com';
$CONF['footer_link'] = '[url]http://mydomain.com[/url]';
$CONF['welcome_text'] = <<<EOM
Welcome to your new account.
EOM;
$CONF['emailcheck_resolve_domain']='YES';
$CONF['show_status']='NO';
$CONF['show_status_key']='NO';
$CONF['show_status_text']='  ';
$CONF['show_undeliverable']='NO';
$CONF['show_undeliverable_color']='tomato';
$CONF['show_undeliverable_exceptions']=array("unixmail.domain.ext","exchangeserver.domain.ext","gmail.com");
$CONF['show_popimap']='NO';
$CONF['show_popimap_color']='darkgrey';
$CONF['show_custom_domains']=array("subdomain.domain.ext","domain2.ext");
$CONF['show_custom_colors']=array("lightgreen","lightblue");
$CONF['recipient_delimiter'] = "";
$CONF['create_mailbox_subdirs_prefix']='INBOX.';
$CONF['used_quotas'] = 'NO';
$CONF['new_quota_table'] = 'NO';
$CONF['theme_logo'] = 'images/logo-default.png';
$CONF['theme_css'] = 'css/default.css';
$CONF['xmlrpc_enabled'] = false;
if (file_exists(dirname(__FILE__) . '/config.local.php')) {
include(dirname(__FILE__) . '/config.local.php');
$CONF['domain_path'] = 'YES';
$CONF['domain_in_mailbox'] = 'YES';
$CONF['database_type'] = 'mysqli';
$CONF['database_host'] = 'localhost';
$CONF['database_user'] = 'postfix_user';
$CONF['database_password'] = 'm/<~VN4XQ!G=jE[A/-';
$CONF['database_name'] = 'postfix_db';
- I went to domain/postfixAdmin/setup.php and domain/roundcube/installer/ and everything was ok.
db.inc.php (roundcube):
<?php
$rcmail_config = array();
$rcmail_config['db_dsnw'] = 'mysql://roundcube_user:%3D%29CYbd9bK%210Z7%29AsWU@localhost/roundcube_db';
$rcmail_config['db_dsnr'] = '';
$rcmail_config['db_persistent'] = FALSE;
$rcmail_config['db_table_users'] = 'users';
$rcmail_config['db_table_identities'] = 'identities';
$rcmail_config['db_table_contacts'] = 'contacts';
$rcmail_config['db_table_contactgroups'] = 'contactgroups';
$rcmail_config['db_table_contactgroupmembers'] = 'contactgroupmembers';
$rcmail_config['db_table_session'] = 'session';
$rcmail_config['db_table_cache'] = 'cache';
$rcmail_config['db_table_cache_index'] = 'cache_index';
$rcmail_config['db_table_cache_thread'] = 'cache_thread';
$rcmail_config['db_table_cache_messages'] = 'cache_messages';
$rcmail_config['db_table_dictionary'] = 'dictionary';
$rcmail_config['db_table_searches'] = 'searches';
$rcmail_config['db_table_system'] = 'system';
$rcmail_config['db_sequence_users'] = 'user_ids';
$rcmail_config['db_sequence_identities'] = 'identity_ids';
$rcmail_config['db_sequence_contacts'] = 'contact_ids';
$rcmail_config['db_sequence_contactgroups'] = 'contactgroups_ids';
$rcmail_config['db_sequence_searches'] = 'search_ids';
main.inc.php(roundcube):
<?php
$rcmail_config = array();
$rcmail_config['debug_level'] = 5;
$rcmail_config['log_driver'] = 'file';
$rcmail_config['log_date_format'] = 'd-M-Y H:i:s O';
$rcmail_config['syslog_id'] = 'roundcube';
$rcmail_config['syslog_facility'] = LOG_USER;
$rcmail_config['smtp_log'] = true;
$rcmail_config['log_logins'] = false;
$rcmail_config['log_session'] = false;
$rcmail_config['sql_debug'] = false;
$rcmail_config['imap_debug'] = false;
$rcmail_config['ldap_debug'] = false;
$rcmail_config['smtp_debug'] = false;
$rcmail_config['default_host'] = 'tls://localhost/';
$rcmail_config['default_port'] = 993;
$rcmail_config['imap_auth_type'] = null;
$rcmail_config['imap_delimiter'] = null;
$rcmail_config['imap_ns_personal'] = null;
$rcmail_config['imap_ns_other'] = null;
$rcmail_config['imap_ns_shared'] = null;
$rcmail_config['imap_force_caps'] = false;
$rcmail_config['imap_force_lsub'] = false;
$rcmail_config['imap_force_ns'] = false;
$rcmail_config['imap_timeout'] = 0;
$rcmail_config['imap_auth_cid'] = null;
$rcmail_config['imap_auth_pw'] = null;
$rcmail_config['imap_cache'] = null;
$rcmail_config['messages_cache'] = false;
$rcmail_config['smtp_server'] = 'tls://localhost/';
$rcmail_config['smtp_port'] = 587;
$rcmail_config['smtp_user'] = '';
$rcmail_config['smtp_pass'] = '';
$rcmail_config['smtp_auth_type'] = '';
$rcmail_config['smtp_auth_cid'] = null;
$rcmail_config['smtp_auth_pw'] = null;
$rcmail_config['smtp_helo_host'] = '';
$rcmail_config['smtp_timeout'] = 0;
$rcmail_config['enable_installer'] = false;
$rcmail_config['dont_override'] = array();
$rcmail_config['support_url'] = '';
$rcmail_config['skin_logo'] = 'sorrybutnocookie';
$rcmail_config['auto_create_user'] = true;
$rcmail_config['user_aliases'] = false;
$rcmail_config['log_dir'] = 'logs/';
$rcmail_config['temp_dir'] = 'temp/';
$rcmail_config['message_cache_lifetime'] = '10d';
$rcmail_config['force_https'] = false;
$rcmail_config['use_https'] = false;
$rcmail_config['login_autocomplete'] = 0;
$rcmail_config['login_lc'] = 2;
$rcmail_config['skin_include_php'] = false;
$rcmail_config['display_version'] = false;
$rcmail_config['session_lifetime'] = 10;
$rcmail_config['session_domain'] = '';
$rcmail_config['session_name'] = null;
$rcmail_config['session_auth_name'] = null;
$rcmail_config['session_path'] = null;
$rcmail_config['session_storage'] = 'db';
$rcmail_config['memcache_hosts'] = null;
$rcmail_config['ip_check'] = true;
$rcmail_config['referer_check'] = false;
$rcmail_config['x_frame_options'] = 'sameorigin';
$rcmail_config['des_key'] = '0JaV%FnEivx9e+JdH2g*?n3n';
$rcmail_config['username_domain'] = '';
$rcmail_config['mail_domain'] = '';
$rcmail_config['password_charset'] = 'ISO-8859-1';
$rcmail_config['sendmail_delay'] = 0;
$rcmail_config['max_recipients'] = 0;
$rcmail_config['max_group_members'] = 0;
$rcmail_config['useragent'] = 'Roundcube Webmail/'.RCMAIL_VERSION;
$rcmail_config['product_name'] = 'Test';
$rcmail_config['include_host_config'] = false;
$rcmail_config['generic_message_footer'] = '';
$rcmail_config['generic_message_footer_html'] = '';
$rcmail_config['http_received_header'] = false;
$rcmail_config['http_received_header_encrypt'] = false;
$rcmail_config['mail_header_delimiter'] = NULL;
$rcmail_config['line_length'] = 72;
$rcmail_config['send_format_flowed'] = true;
$rcmail_config['mdn_use_from'] = false;
$rcmail_config['identities_level'] = 0;
$rcmail_config['client_mimetypes'] = null;
$rcmail_config['mime_magic'] = null;
$rcmail_config['mime_types'] = null;
$rcmail_config['im_identify_path'] = null;
$rcmail_config['im_convert_path'] = null;
$rcmail_config['image_thumbnail_size'] = 240;
$rcmail_config['contact_photo_size'] = 160;
$rcmail_config['email_dns_check'] = false;
$rcmail_config['no_save_sent_messages'] = false;
$rcmail_config['plugins'] = array();
$rcmail_config['message_sort_col'] = '';
$rcmail_config['message_sort_order'] = 'DESC';
$rcmail_config['list_cols'] = array('subject', 'status', 'fromto', 'date', 'size', 'flag', 'attachment');
$rcmail_config['language'] = null;
$rcmail_config['date_format'] = 'Y-m-d';
$rcmail_config['date_formats'] = array('Y-m-d', 'Y/m/d', 'Y.m.d', 'd-m-Y', 'd/m/Y', 'd.m.Y', 'j.n.Y');
$rcmail_config['time_format'] = 'H:i';
$rcmail_config['time_formats'] = array('G:i', 'H:i', 'g:i a', 'h:i A');
$rcmail_config['date_short'] = 'D H:i';
$rcmail_config['date_long'] = 'Y-m-d H:i';
$rcmail_config['drafts_mbox'] = 'Drafts';
$rcmail_config['junk_mbox'] = 'Junk';
$rcmail_config['sent_mbox'] = 'Sent';
$rcmail_config['trash_mbox'] = 'Trash';
$rcmail_config['default_folders'] = array('INBOX', 'Drafts', 'Sent', 'Junk', 'Trash');
$rcmail_config['create_default_folders'] = false;
$rcmail_config['protect_default_folders'] = true;
$rcmail_config['quota_zero_as_unlimited'] = false;
$rcmail_config['enable_spellcheck'] = false;
$rcmail_config['spellcheck_dictionary'] = false;
$rcmail_config['spellcheck_engine'] = 'googie';
$rcmail_config['spellcheck_uri'] = '';
$rcmail_config['spellcheck_languages'] = NULL;
$rcmail_config['spellcheck_ignore_caps'] = false;
$rcmail_config['spellcheck_ignore_nums'] = false;
$rcmail_config['spellcheck_ignore_syms'] = false;
$rcmail_config['recipients_separator'] = ',';
$rcmail_config['max_pagesize'] = 200;
$rcmail_config['min_refresh_interval'] = 60;
$rcmail_config['upload_progress'] = false;
$rcmail_config['undo_timeout'] = 0;
$rcmail_config['address_book_type'] = 'sql';
$rcmail_config['ldap_public'] = array();
$rcmail_config['autocomplete_addressbooks'] = array('sql');
$rcmail_config['autocomplete_min_length'] = 1;
$rcmail_config['autocomplete_threads'] = 0;
$rcmail_config['autocomplete_max'] = 15;
$rcmail_config['address_template'] = '{street}<br/>{locality} {zipcode}<br/>{country} {region}';
$rcmail_config['addressbook_search_mode'] = 0;
$rcmail_config['default_charset'] = 'ISO-8859-1';
$rcmail_config['skin'] = 'larry';
$rcmail_config['mail_pagesize'] = 50;
$rcmail_config['addressbook_pagesize'] = 50;
$rcmail_config['addressbook_sort_col'] = 'surname';
$rcmail_config['addressbook_name_listing'] = 0;
$rcmail_config['timezone'] = 'auto';
$rcmail_config['prefer_html'] = true;
$rcmail_config['show_images'] = 0;
$rcmail_config['message_extwin'] = false;
$rcmail_config['compose_extwin'] = false;
$rcmail_config['htmleditor'] = 0;
$rcmail_config['prettydate'] = true;
$rcmail_config['draft_autosave'] = 300;
$rcmail_config['preview_pane'] = false;
$rcmail_config['preview_pane_mark_read'] = 0;
$rcmail_config['logout_purge'] = false;
$rcmail_config['logout_expunge'] = false;
$rcmail_config['inline_images'] = true;
$rcmail_config['mime_param_folding'] = 0;
$rcmail_config['skip_deleted'] = false;
$rcmail_config['read_when_deleted'] = true;
$rcmail_config['flag_for_deletion'] = false;
$rcmail_config['refresh_interval'] = 60;
$rcmail_config['check_all_folders'] = false;
$rcmail_config['display_next'] = true;
$rcmail_config['autoexpand_threads'] = 0;
$rcmail_config['reply_mode'] = 0;
$rcmail_config['strip_existing_sig'] = true;
$rcmail_config['show_sig'] = 1;
$rcmail_config['force_7bit'] = false;
$rcmail_config['search_mods'] = null;
$rcmail_config['addressbook_search_mods'] = null;
$rcmail_config['delete_always'] = false;
$rcmail_config['delete_junk'] = false;
$rcmail_config['mdn_requests'] = 0;
$rcmail_config['mdn_default'] = 0;
$rcmail_config['dsn_default'] = 0;
$rcmail_config['reply_same_folder'] = false;
$rcmail_config['forward_attachment'] = false;
$rcmail_config['default_addressbook'] = null;
$rcmail_config['spellcheck_before_send'] = false;
$rcmail_config['autocomplete_single'] = false;
$rcmail_config['default_font'] = 'Verdana';
- From what i can see, postfixadmin used and populated its database, but not roundcube.
- I can open postfixadmin and log in with no apparent errors (not that i know what to do with it instead of roundcube, but at least works...)
- Whenever i open roundcube it begins to output errors everywhere about db connection (I was only able after changing its .htaccess to Allow from all, is it a bad idea?)
DB Error in /usr/share/webapps/roundcubemail/program/lib/Roundcube/rcube_db.php (416): [1146] Table 'roundcube_db.session' doesn't exist (SQL Query: SELECT vars, ip, changed FROM session WHERE sess_id = 'pq5ofv7ja0gh2sunsg38jmd3g1')
Warning: session_start(): Cannot send session cache limiter - headers already sent in /usr/share/webapps/roundcubemail/program/lib/Roundcube/rcube.php on line 445
DB Error: [1146] Table 'roundcube_db.session' doesn't exist
DATABASE ERROR: CONNECTION FAILED!
Unable to connect to the database!
Please contact your server-administrator.
DB Error in /usr/share/webapps/roundcubemail/program/lib/Roundcube/rcube_db.php (416): [1146] Table 'roundcube_db.session' doesn't exist (SQL Query: INSERT INTO session (sess_id, vars, ip, created, changed) VALUES ('pq5ofv7ja0gh2sunsg38jmd3g1', 'dGVtcHxiOjE7bGFuZ3VhZ2V8czo1OiJlbl9VUyI7dGFza3xzOjU6ImxvZ2luIjs=', 'xxx.xxx.xxx.xxx', '2014-02-08 07:34:46', '2014-02-08 07:34:46'))
Thats all i know. Whats wrong? (i already tried to set db logins with no pw at all, but still with the same problems)
How far am i to be able to send/receive one email? Please, tell me i am close...
Mail servers could be so much more linear to set up
Thanks for your help. Time to get some sleep!

The roundcube db schema needs to setup manually. See /usr/share/webapps/roundcube/INSTALL
Also, from your /etc/webapps/postfixadmin/config.inc.php:
$CONF['domain_path'] = 'NO';
$CONF['domain_in_mailbox'] = 'YES';
$CONF['maildir_name_hook'] = 'NO';
..which results in /var/mail/vmail/[email protected]
From your dovecot.conf
mail_home = /var/mail/vmail/%d/%u
...which results in /var/mail/vmail/domain.com/user
That doesn't fit together.

R6870 setup

Similar Messages

Maybe you are looking for