RAC 10g windows 2003 with ocfs

Hello,
I have a problem...
How make to install the ocfs in the windows 2003?
Somebody can help me with some documentation or step-by-step?
tanks.

Hi,
OCFS has nothing compare with ORACLE_HOME.
OCFS is only a Filesytem how you can format the drives.
And with this drives you can schare over OCFS drivers the disks over multiple servers.
ASM is a Oracle Product and a very small Database how managed the Files so a Oracle_home is needed by ASM while example you can applay patches to ASM for bugs etc...

Similar Messages

  • Trying to config RAC on Windows 2003 EE

    I am trying top configure 10g RAC on windows 2003 EE with the help of VMWARE Workstation 5.0.
    I am getting the below error while running clusterverification,,
    E:\clusterware\cluvfy>runcluvfy stage -post hwos -n RAC1,RAC2
    The system cannot find the path specified.
    Performing post-checks for hardware and operating system setup
    Checking node reachability...
    Node reachability check passed from node "RAC1".
    Checking user equivalence...
    User equivalence check passed for user "Administrator".
    Checking node connectivity...
    Node connectivity check passed for subnet "192.168.1.0" with node(s) RAC2,RAC1.
    Node connectivity check passed for subnet "10.0.0.0" with node(s) RAC2,RAC1.
    Suitable interfaces for the private interconnect on subnet "192.168.1.0":
    RAC2 public:192.168.1.102
    RAC1 public:192.168.1.101
    Suitable interfaces for the private interconnect on subnet "10.0.0.0":
    RAC2 private:10.10.10.2
    RAC1 private:10.10.10.1
    ERROR:
    Could not find a suitable set of interfaces for VIPs.
    Node connectivity check failed.
    Checking shared storage accessibility...
    Disk Partition Sharing Nodes (2 in count)
    \Device\Harddisk1\Partition1 RAC2 RAC1
    Disk Partition Sharing Nodes (2 in count)
    \Device\Harddisk1\Partition2 RAC2 RAC1
    Disk Partition Sharing Nodes (2 in count)
    \Device\Harddisk1\Partition3 RAC2 RAC1
    Disk Partition Sharing Nodes (2 in count)
    \Device\Harddisk1\Partition4 RAC2 RAC1
    Disk Partition Sharing Nodes (2 in count)
    \Device\Harddisk1\Partition5 RAC2 RAC1
    Shared storage check was successful on nodes "RAC2,RAC1".
    Post-check for hardware and operating system setup was unsuccessful on all the n
    odes.
    my VIP IP address are in the same subnet of public IPs
    ie 192.168.1.151 is RAC1-VIP and 192.168.1.152 is RAC2-VIP,
    Any help appreciated!!!!
    .

    Joy,
    I hope the following presentation might help you.
    http://www.oracle-base.com/articles/10g/OracleDB10gR2RACInstallationOnWindows2003UsingVMware.php
    http://julian.dyke.users.btopenworld.com/com/Presentations/Presentations.html#RACOnWindows2003
    Jaffar

  • Requeriments OS for installation Oracle 11g RAC  in Windows 2003

    I plan to install Oracle 11g Standard with RAC in Windows 2003 Server.
    I will use 2 nodes with the same OS.
    I will use a SAN with fibre channel, to store the DB.
    It is possible to install Oracle RAC in W2003 Standard ?
    I need obligatory W2003 Enterprise?
    The cluster of the 2 nodes is made by OS or by Oracle Clusterware?
    Thanks in advance.

    You can install on Windows 2003 Standard, it works with this OS. On the other hand the cluster is configured by the oracle clusterware. You need to make absolutely sure you are able to write from both nodes to the shared storage. Specific details on the regedit parameters you have to configure and specific OS issues are detailed at the above reference Werner posted.
    ~ Madrid

  • NTLM is not working with EP 6 SP 9 on Windows 2003 with IIS 6.

    I installed EP 6 SP 9 on windiows 2003 server with IIS version 6.
    Configures IisProxy.xml for redirection for filter irj. When  I make a call to default website, it in turn calls server with irj filter.
    Portal page comes up and requesting me to enter user id password.
    I made the changes mentioned by some of the web logs in this site.
    I configured HeaderVariableLoginModule an and added as explined by Gregory Wolf on the following topic.
    Integrated Windows Authentication with SAP EP 6.0 SP 3 and higher.
    I see following log from Ep 6 SP 9 log file security.log from directory E:\usr\sap\DEV\JC00\j2ee\cluster\server0\log\system.
    security#Plain###No user name provided.#
    #1.5#000C2953326B00430000000100000A780003F358EF2132DE#1111988099323#/System/Security#sap.com/irj#com.sap.engine.services.security#Guest#18####200d0cb09f4b11d9926a000c2953326b#SAPEngine_Application_Thread[impl:3]_37##0#0#Info#1#com.sap.engine.services.security#Plain###Cannot log info about the logon attempt because the user name is null.#
    #1.5#000C2953326B00440000000000000A780003F3591D22E168#1111988846027#/System/Security#sap.com/irj#com.sap.engine.services.security#Guest#18####dd1f09b19f4c11d98e98000c2953326b#SAPEngine_Application_Thread[impl:3]_7##0#0#Info#1#com.sap.engine.services.security#Plain###No user name provided.#
    #1.5#000C2953326B00440000000100000A780003F3591D22E215#1111988846027#/System/Security#sap.com/irj#com.sap.engine.services.security#Guest#18####dd1f09b19f4c11d98e98000c2953326b#SAPEngine_Application_Thread[impl:3]_7##0#0#Info#1#com.sap.engine.services.security#Plain###Cannot log info about the logon attempt because the user name is null.#
    #1.5#000C2953326B00450000000000000A780003F359227DE92E#1111988935662#/System/Security#sap.com/irj#com.sap.engine.services.security#Guest#18####128c40e09f4d11d9acb7000c2953326b#SAPEngine_Application_Thread[impl:3]_28##0#0#Info#1#com.sap.engine.services.security#Plain###No user name provided.#
    #1.5#000C2953326B00450000000100000A780003F359227DEDC7#1111988935662#/System/Security#sap.com/irj#com.sap.engine.services.security#Guest#18####128c40e09f4d11d9acb7000c2953326b#SAPEngine_Application_Thread[impl:3]_28##0#0#Info#1#com.sap.engine.services.security#Plain###Cannot log info about the logon attempt because the user name is null.#
    Lots of weblogs are pointing to remote_user value in IisProxy.log file. I am not able to see that.
    I also tried switching IIS 6 to run as IIS 5 and did not help much at all.
    Please help me on the issue.
    I did not change authschemes.xml file.
    My IisProxy.xml file looks as follows:
    <?xml version="1.0" encoding="utf-8" ?>
    <!DOCTYPE ISAPI-config[
         <!ELEMENT ISAPI-config ( filter, extension, ( mapping | config )* )>
         <!ATTLIST ISAPI-config
              version CDATA #REQUIRED
         >
         <!ELEMENT filter (log-path?)>
         <!ATTLIST filter
              name CDATA #IMPLIED
              log-level CDATA "3"
              log-flags CDATA "0x00000001"
              debug-flags CDATA "0x00008000"
              priority ( high | medium | low ) "high"
              extension-url CDATA "/scripts/IisProxy.dll"
              authentication ( skip | normal | forward ) "normal"
              remote-address ( skip | forward ) "skip"
         >
         <!ELEMENT extension (
              keystore-dir?,
              log-path?,
              data-path?,
              trace-path? )>
         <!ATTLIST extension
              name CDATA #IMPLIED
              log-level CDATA "1"
              log-flags CDATA "0"
              debug-flags CDATA "0"
              access ( filter | direct | both ) "filter"
         >
         <!ELEMENT keystore-dir (#PCDATA)>
         <!ELEMENT log-path (#PCDATA)>
         <!ELEMENT data-path (#PCDATA)>
         <!ELEMENT trace-path (#PCDATA)>
         <!ELEMENT mapping (
              source+,
              target,
              compress-types*,
              protocol-header?,
              certificate-header?,
              cert-chain-header?,
              cipher-header?,
              keysize-header?,
              keystore-path?,
              log-path?,
              data-path? )>
         <!ATTLIST mapping
              name CDATA #IMPLIED
              log-level CDATA "1"
              log-flags CDATA "0"
              debug-flags CDATA "0"
              keep-alive ( true | false ) "true"
              use-continue ( true | false ) "true"
              close-socket ( true | false ) "true"
              close-socket-delay CDATA "1000"
              thread-count CDATA "100"
              max-socket-age CDATA "37"
         >
         <!ELEMENT source (protocol, host?, port?, prefix, new-prefix?)>
         <!ATTLIST source
              access ( filter | direct | both ) "filter"
         >
         <!ELEMENT protocol (#PCDATA)>
         <!ELEMENT host (#PCDATA)>
         <!ELEMENT port (#PCDATA)>
         <!ELEMENT prefix (#PCDATA)>
         <!ELEMENT new-prefix (#PCDATA)>
         <!ELEMENT target (protocol, host, port)>
         <!ELEMENT compress-types (#PCDATA)>
         <!ATTLIST compress-types
              min-size CDATA "1024"
         >
         <!ELEMENT protocol-header (#PCDATA)>
         <!ELEMENT certificate-header (#PCDATA)>
         <!ELEMENT cert-chain-header (#PCDATA)>
         <!ELEMENT cipher-header (#PCDATA)>
         <!ELEMENT keysize-header (#PCDATA)>
         <!ELEMENT keystore-path (#PCDATA)>
         <!ELEMENT config ( source+ )>
    ]>
    <ISAPI-config version="1.6">
         <filter name="IisProxy filter"/>
         <extension name="IisProxy extension" />
         <mapping name="IisProxy samples">
              <source>
                   <protocol>http</protocol>
                   <prefix>/irj</prefix>
              </source>
              <source>
                   <protocol>http</protocol>
                   <prefix>/Hello/</prefix>
              </source>
              <source>
                   <protocol>http</protocol>
                   <prefix>/Hello2/</prefix>
                   <new-prefix>/Hello/</new-prefix>
              </source>
              <target>
                   <protocol>http</protocol>
                   <host>slcsepw04vd.pacificorp.us</host>
                   <port>50000</port>
              </target>
              <compress-types>text/html, text/plain</compress-types>
         </mapping>
         <mapping name="Secure IisProxy samples">
              <source>
                   <protocol>https</protocol>
                   <prefix>/Hello/</prefix>
              </source>
              <target>
                   <protocol>https</protocol>
                   <host>localhost.your.corp</host>
                   <port>8443</port>
              </target>
              <keystore-path>c:\sec\SAPSSLC.pse</keystore-path>
         </mapping>
         <config>
              <source>
                   <protocol>http</protocol>
                   <host>localhost</host>
                   <prefix>/IisProxy</prefix>
              </source>
              <source>
                   <protocol>https</protocol>
                   <host>localhost</host>
                   <prefix>/IisProxy</prefix>
              </source>
         </config>
    </ISAPI-config>
    Please help me. I am not sure what is missing. Please make a note that Portal version is EP 6 SP9 & Server is Windows 2003 with IIS 6.

    I made the change as you requested and it did not help.
    I do not see any remote_user entry in IisProxy.log file.
    Please let me know the procedure to get REMOTE_USER into the IisProxy.log file.
    <?xml version="1.0" encoding="utf-8" ?>
    <!DOCTYPE ISAPI-config[
         <!ELEMENT ISAPI-config ( filter, extension, ( mapping | config )* )>
         <!ATTLIST ISAPI-config
              version CDATA #REQUIRED
         >
         <!ELEMENT filter (log-path?)>
         <!ATTLIST filter
              name CDATA #IMPLIED
              log-level CDATA "3"
              log-flags CDATA "0x00000001"
              debug-flags CDATA "0x00008000"
              priority ( high | medium | low ) "high"
              extension-url CDATA "/scripts/IisProxy.dll"
              authentication ( skip | normal | forward ) "normal"
              remote-address ( skip | forward ) "skip"
         >
         <!ELEMENT extension (
              keystore-dir?,
              log-path?,
              data-path?,
              trace-path? )>
         <!ATTLIST extension
              name CDATA #IMPLIED
              log-level CDATA "1"
              log-flags CDATA "0"
              debug-flags CDATA "0"
              access ( filter | direct | both ) "filter"
         >
         <!ELEMENT keystore-dir (#PCDATA)>
         <!ELEMENT log-path (#PCDATA)>
         <!ELEMENT data-path (#PCDATA)>
         <!ELEMENT trace-path (#PCDATA)>
         <!ELEMENT mapping (
              source+,
              target,
              compress-types*,
              protocol-header?,
              certificate-header?,
              cert-chain-header?,
              cipher-header?,
              keysize-header?,
              keystore-path?,
              log-path?,
              data-path? )>
         <!ATTLIST mapping
              name CDATA #IMPLIED
              log-level CDATA "1"
              log-flags CDATA "0"
              debug-flags CDATA "0"
              keep-alive ( true | false ) "true"
              use-continue ( true | false ) "true"
              close-socket ( true | false ) "true"
              close-socket-delay CDATA "1000"
              thread-count CDATA "100"
              max-socket-age CDATA "37"
         >
         <!ELEMENT source (protocol, host?, port?, prefix, new-prefix?)>
         <!ATTLIST source
              access ( filter | direct | both ) "filter"
         >
         <!ELEMENT protocol (#PCDATA)>
         <!ELEMENT host (#PCDATA)>
         <!ELEMENT port (#PCDATA)>
         <!ELEMENT prefix (#PCDATA)>
         <!ELEMENT new-prefix (#PCDATA)>
         <!ELEMENT target (protocol, host, port)>
         <!ELEMENT compress-types (#PCDATA)>
         <!ATTLIST compress-types
              min-size CDATA "1024"
         >
         <!ELEMENT protocol-header (#PCDATA)>
         <!ELEMENT certificate-header (#PCDATA)>
         <!ELEMENT cert-chain-header (#PCDATA)>
         <!ELEMENT cipher-header (#PCDATA)>
         <!ELEMENT keysize-header (#PCDATA)>
         <!ELEMENT keystore-path (#PCDATA)>
         <!ELEMENT config ( source+ )>
    ]>
    <ISAPI-config version="1.6">
         <filter name="IisProxy filter" authentication="forward"/>
         <extension name="IisProxy extension" />
         <mapping name="IisProxy samples">
              <source>
                   <protocol>http</protocol>
                   <prefix>/irj</prefix>
              </source>
              <source>
                   <protocol>http</protocol>
                   <prefix>/Hello/</prefix>
              </source>
              <source>
                   <protocol>http</protocol>
                   <prefix>/Hello2/</prefix>
                   <new-prefix>/Hello/</new-prefix>
              </source>
              <target>
                   <protocol>http</protocol>
                   <host>slcsepw04vd.pacificorp.us</host>
                   <port>50000</port>
              </target>
              <compress-types>text/html, text/plain</compress-types>
         </mapping>
         <mapping name="Secure IisProxy samples">
              <source>
                   <protocol>https</protocol>
                   <prefix>/Hello/</prefix>
              </source>
              <target>
                   <protocol>https</protocol>
                   <host>localhost.your.corp</host>
                   <port>8443</port>
              </target>
              <keystore-path>c:secSAPSSLC.pse</keystore-path>
         </mapping>
         <config>
              <source>
                   <protocol>http</protocol>
                   <host>localhost</host>
                   <prefix>/IisProxy</prefix>
              </source>
              <source>
                   <protocol>https</protocol>
                   <host>localhost</host>
                   <prefix>/IisProxy</prefix>
              </source>
         </config>
    </ISAPI-config>
    Please let me know what is missing.
    Thanks.

  • Upgrade Oracle Client 8.1.7 to 10g on Windows 2003 with IIS / ASP

    I am having problems after I install 10201_client_win32 on Windows 2003 which uses IIS ASP application to connect via ODBC to Oracle databases.
    tnsping and m/s access can connect but for some reason my ASP application can not connect but doesn't give me any error messages just hangs during ASP database connection
    I have a mixture of 8i and 10g DSN connections which I use, I'm not sure if I need to un-install 8.1.7 driver or remove all 8i ODBC to enable this to work
    Should ASP be able to connect to a mix of 8 and 10g drivers?
    Perhaps some DLL incompatibility or install issue.
    Note it works ok on XP workstation but not so far on Win2003 server.
    Any help to verify install or things to check would be appreciated
    Paul

    Since 8.1.7 was never certified on Windows 2003, it's entirely possible that it would cause some problems and might interfere with the 10g client.
    If you are confident that the setup on your XP box is identical to the setup on the 2003 box, I would tend to suspect that the 8.1.7 client was causing the problem.
    Justin

  • Slow response on Windows 2003 with web forms

    We are current running Oracle web forms on thin clients on Windows 2000 terminal server. We have installed Windows 2003 on one node of the cluster. When we run the same application on 2003, it is very slow and the screen flashes a lot. It takes 1-2 seconds to echo a keystroke. This is true for Jinitiator 1.3.1.25 and 1.3.1.18. We are using 1.3.1.18 on the Win 2000 terminal server. When I try form=test on Win 2003, the screen has colors and has poorer resolution that running the same on Win2003. The form has a grey background on Win 2000 but is magenta in Win 2003 and you can barely make out the hammer in the prompt. This happens when running from the same thin client with the same resolution and colors. Is there a setting on IE that could be causing this? Is there a problem with Win 2003? The Oracle application server is 9iAS but we see the same probelm with 10g.
    Thanks,
    Dave

    Copying my response from this thread:
    Report in Designer fast, in Viewer extremely slow
    Thread is now locked.
    A "cool" issue, form my perspective as this may be something new to think about / figure out. Not so cool from where you sit...
    Anyhow, a few things to check:
    1) Compare the runtime of your dev system and the Citrix system. Use Modules to do the comparison.
    2) Not sure what runtime was installed, but the most recent MSI / MSM are from SP 1.4:
    MSI
    https://smpdl.sap-ag.de/~sapidp/012002523100004610752009E/cr2008_fp14_ri.zip
    MSM
    https://smpdl.sap-ag.de/~sapidp/012002523100004610922009E/cr2008_fp14_mm.zip
    Trying the FP 1.4 runtime will be worth a shot.
    3) How is the performance on the Citrix when you actually sit right on the server, and not on a work station?
    4) Where is the slow down occurring (unfortunately this will require a bit of temporary code modification)? But the bottle necks typically are at:
    -report load
    - connection to the data source
    - setting of parameters
    - actual report output, be it to a viewer, export or printer.
    I suggest a possible way of tackling this in the performance article (page 4):
    https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/8029cc96-6ff3-2b10-47a2-b30ea790ea5b
    Ludek

  • Advantages/Disadvantages of installing Oracle RAC on Windows 2003 VS Linux

    Hello Guys,
    I am not very good with linux, have to create a Oracle RAC environment using dataabse 10g.
    I just need to know the advantages/disadvantages of configuring RAC on windows and on linux operating system.
    Please help me with this. Please also specify what is the best available windows and linux version to configure RAC.
    Regards,
    Imran

    Go with th eOS you have the skills in, if you have onsite expertise in windows then it makes no sense to use Linux because some guy on the internet says its better. Windows can be a highly available server OS when is managed by professional well quallified adminstrators.
    Personally I would use linux because I am more familiar with the OS than windows. I also find oracle makes more sense on a *NIX type platform but there are shops that run oracle on windows with the required high availability.                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       

  • Xp_logininfo "Installation problem on windows 2003 with Sql 2005"

    Hi every one
    I am facing a problem during the installation of Solution Manager 4.0 on Windows 2003 server with Ms Sql 2005, I received the following error
    Msg 15404, Level 16, State 19, Procedure xp_logininfo, Line 60.
    Its some how look likes that the user "SID"ADM
    Can any one give me a clue
    thanks
    Kind Regards
    Sohail

    Hi All,
    This would solve your problem
    First of all this error is <b>MSSQL error</b>.
    When you perform an action on an instance of SQL Server that requires SQL Server to resolve the credentials of a Microsoft Windows NT domain user account, you may receive an error message that is similar
    Server: Msg 8198, Level 16, State XX, Procedure <Stored Procedure Name>, Line <line Number>
    Could not obtain information about Windows NT group/user '<Domain\Account Name>'.
    To resolve the credentials of a Windows NT domain user account, SQL Server uses the xp_logininfo system stored procedure. Here is a list of the common scenarios where you may notice that the xp_logininfo system stored procedure fails and causes the 8198 error.
    • When you use an xp_sendmail extended stored procedure.
    • When you set up replication.
    • When you run a SQL Server Agent job.
    SQL Server may run the xp_logininfo system stored procedure to retrieve information about the Windows domains and the user accounts, even if the user does not do so explicitly. Therefore, if you receive an 8198 error message and the error message mentions the xp_logininfo system stored procedure as the procedure, you must use <b>SQL Profiler</b> to trace and to troubleshoot the exact point of failure.
    You can go through this link for more info...
    http://support.microsoft.com/?kbid=834124
    Feel Free to Revert back...
    --Thanks and Regards,
    Ragu
    ERP,
    Suzlon Energy Limted, Pune
    Extn: 2638
    +919370675797
    I have no limits for others sky is only a reason

  • Cisco aironet 1130g and windows 2003 with cisco ACS

      hi
    i  have configured windows 2003 server with  DNS ,Active directory users and dhcp server.  and configured my cisco 1130g AP .
    i have installed cisco access control server 4.0 because i use LEAP authentication protocol and for the ACS for network configuration i give aaa client ip addresss as AP interface ip and  same shared secret for the AP and ACS,.
    so  when i log to wifi it ask username and password
    problem is lap top cannot have a ip address my dhcp server not issue any ip address .
    my hiper terminal massage is like this when i connect to wifi 
    help ...thank you...

    As I mentioned now several times already, it is the client and ACS which do the PEAP. The Access point doesn't have to be configured for an eap type. What you did on the AP was setting the AP as a radius server which is duplicate work with what you did on ACS.
    So you need on your client to configure either PEAP or LEAP.
    Nicolas

  • Oracle upgrade from 32-bit Oracle 9i to 64-bit Oracle 10g (Windows 2003 R2)

    Hello Gurus,
    Existing I have SAP R/3 4.7 200 Oracle 9i Windows 2003 32bit
    I want to upgrade Hardware to x86 EMT64bit 
    I would like to upgrade to 64-bit Oracle 10G from 32-bit Oracle 9i. runs on Windows 2003 32bit. Target DB is Oracle 10G on x64 Windows (EMT64 hardware) on Windwos 2003R2 64bit. & Add Solution manager to new System
    Please give me any advise which is the better way of upgrading Oracle 10g. Or better yet, please advise a safe way of upgrading to Oracle 10g from 9i
    Please guide me about request shipping DVD For This Solution to my site
    Many thank in advance
    Kuekul

    Hi
    You can download Oracle 10g from service market place www.service.sap.com>downlaods>Installations and Upgrades-->
    Installations and Upgrades - Entry by Application Group>SAP NetWeaver>SAP NetWeaver7.0>Installation and upgrade>windows server-->oracle check for below software and download it
      EXE 51031678_1 ORACLE RDBMS 10.2 Windows 1 of 5 
      RAR 51031678_2 ORACLE RDBMS 10.2 Windows 2 of 5 
      RAR 51031678_3 ORACLE RDBMS 10.2 Windows 3 of 5 
      RAR 51031678_4 ORACLE RDBMS 10.2 Windows 4 of 5  
      RAR 51031678_5 ORACLE RDBMS 10.2 Windows 5 of 5
      ZIP 51033272 ORACLE 10.2 Client  
    ZIP 51036971_2 ORACLE RDBMS Patch 10.2.0.4 Windows Server on IA32 32bit 
    ZIP 51036971_3 ORACLE RDBMS Patch 10.2.0.4 Windows Server on IA64 64bit 
    ZIP 51036971_4 ORACLE RDBMS Patch 10.2.0.4 Windows Server on x64 64bit 
    Regards
    Uday

  • Oracle (Linux) to MS SQL Server 2000 (Windows 2003) with OTG

    I have Oracle 9i Release 1 running on linux and i want to use Transparent Gateway to connect to MS SQL Server 2000 running on Windows 2003. Is it possible to setup this connection?
    If yes, please include the detail approach of installation.
    Thank you....

    Dear kgronau
    i tried the transperent gateway in Win2003
    both sqlserver and oracle 10 g onthe same os (win2003)
    Created listener and tnsname settings as per the documention spec..
    then created a database link for sqlserver here.
    my transpernet gateway works without any problem,
    Then,
    I have Oracle on Linux also,
    i created a tnsname settings here for the win2003 listener (for sqlserver connection).
    then created a database link for sqlserver here
    im not able to connect sqlserver.
    i tried to desc one table (sqlserver)
    the following error i get,
    do you have any idea, what i have missed???
    SQL> DESC CUSTOMERS@SQLDB
    ERROR:
    ORA-02068: following severe error form SQLDB
    ORA-03135: connection lost contact
    please give some hints what is the problem
    remember the listener is running on windows 2003
    regards

  • Please kindly tell me how to run autoconfig in r12 on windows 2003 with every step in detail?

    I got installed oracle R12 in windows 2003
    the service oracleconcrmgrvis not starting after 2-3 time the laptop shut in between due to power shutdown
    Please anybody kindly tell me in detail every step
    I don't know how to log in applmgr and where to login applmgr in application tier
    and where to run the autoconfig
    I also don't know how to log in as oracle database tier and where to login
    I also dont have the sqlplus username/password kindly tell me how to change or find the username/password
    I know very less in this subject I spend 4 hrs to to solve the and start the service but in vain
    Dear gurus pls help me

    Check the CM log file under $APPLCSF/$APPLLOG directory, search for <SID>*.mgr file (or from the application -- Concurrent > Manager > Administer).
    For the database log file, issue "show parameter diagnostic_dest" from sqlplus.
    AutoConfig details can be found in (Using AutoConfig to Manage System Configurations in Oracle E-Business Suite Release 12 (Doc ID 387859.1)).
    Thanks,
    Hussein

  • INSTALL Oracle 10g RAC on Windows 2003. ERROR on starting services

    During installation assistances try to configure and start RAC services,
    but I get next message with error:
    Starting to execute configuration assistants
    Launched configuration assistant 'Oracle Cluster Ready Services Configuration Assistant'
    Tool type is: Optional.
    The command being spawned is: 'C:\oracle\product\10.1.0\crs/install/crssetup.config.bat'
    Start output from spawned process:
    clscfg: EXISTING configuration version 2 detected.
    clscfg: version 2 is 10G Release 1.
    Successfully accumulated necessary OCR keys.
    Using ports: CSS=49895 CRS=49896 EVMC=49898 and EVMR=49897.
    node <nodenumber>: <nodename> <private interconnect name> <hostname>
    node 1: bdserver01 oracnode01 bdserver01
    node 2: bdserver02 oracnode02 bdserver02
    clscfg: Arguments check out successfully.
    NO KEYS WERE WRITTEN. Supply -force parameter to override.
    -force is destructive and will destroy any previous cluster
    configuration.
    Step 1: checking status of CRS cluster
    Step 2: configuring OCR repository
    Oracle Cluster Registry already initialized
    Step 3: configuring safe mode for CRS stack
    Step 4: Starting up CRS stack on all nodes
    bdserver01 service OracleCSService in improper PENDING state, err(997)
    bdserver02 service OracleCSService in improper PENDING state, err(997)
    :-(((

    During installation assistances try to configure and start RAC services,
    but I get next message with error:
    Starting to execute configuration assistants
    Launched configuration assistant 'Oracle Cluster Ready Services Configuration Assistant'
    Tool type is: Optional.
    The command being spawned is: 'C:\oracle\product\10.1.0\crs/install/crssetup.config.bat'
    Start output from spawned process:
    clscfg: EXISTING configuration version 2 detected.
    clscfg: version 2 is 10G Release 1.
    Successfully accumulated necessary OCR keys.
    Using ports: CSS=49895 CRS=49896 EVMC=49898 and EVMR=49897.
    node <nodenumber>: <nodename> <private interconnect name> <hostname>
    node 1: bdserver01 oracnode01 bdserver01
    node 2: bdserver02 oracnode02 bdserver02
    clscfg: Arguments check out successfully.
    NO KEYS WERE WRITTEN. Supply -force parameter to override.
    -force is destructive and will destroy any previous cluster
    configuration.
    Step 1: checking status of CRS cluster
    Step 2: configuring OCR repository
    Oracle Cluster Registry already initialized
    Step 3: configuring safe mode for CRS stack
    Step 4: Starting up CRS stack on all nodes
    bdserver01 service OracleCSService in improper PENDING state, err(997)
    bdserver02 service OracleCSService in improper PENDING state, err(997)
    :-(((

  • Reg: Installing Oracle RAC on windows 2003 32 bit

    Hello All,
    I am new to Oracle RAC
    Currently I have two systems with 32bit processor and windows server 2003 installed.
    I need to configure Oracle RAC in the above 32 bit systems using openfiler/vmware
    Is it possible?

    Currently I have two systems with 32bit processor and windows server 2003 installed.
    I need to configure Oracle RAC in the above 32 bit systems using openfiler/vmwareGrid Infrastructure 11.2 for Windows is only 64-bit.
    You can try 11.1.

  • Oracle Secure Backup 10.3.0.3.0 in Windows 2003 with IBM Tape Not Working

    Hi,
    I am currently implementing Oracle Secure Backup. My environment is this:
    OS: Windows Server 2003 (32Bit) for all servers
    Database: Oracle Database 11.2.0.1.0
    Tape Library: IBM-ULT 3580-TD4
    I will have to configure 2 machines to work with OSB: server01 and server02.
    Server01:
    This serves as the client, admin, mediaserver
    Server02:
    This will serve as the client, admin
    When I log in to Server01, in the device manager, I can see the Tape Drives (no warnings, no questions marks) so I think it's good.
    When I log in to Server02, in the device manager, there are no Tape Drives seen. Is is ok or shall i configure the IBM Tape drives to be also accessible since this is just the client, admin host?
    Also I have noticed that when I installed the OSB in Server02 (client,admin), when I am on the SCSI Devices, i dont see any tape device (since its not in the device manager). Because of this i cannot start OSB Services and cannot add this host to the mediaserver.
    Also, I am having issues Configuring the Library and the devices. I have read the official documentation completely but i think its very general and it does not present the detailed step-by-step process in installing and configuring OSB.
    When I issued: lsdev -lvg in the mediaserver , I can read an error: Warning: bus info unknown or drive not installed.
    Help is very much appreciated. Thanks a lot guys!

    I have resolved the issue. Ill close this thread. :))

Maybe you are looking for

  • Website Translation

    Hi all My question is about how to make websites work in different languages. As I operate my business with customers throughout INDIA I need to present my website in several languages. How does this work? Once I have the text translated, do I have t

  • How do I get my music off of my first generation nano to a new library?

    I have the very first nano and I am trying to move the music onto a new library then from the new library onto a new nano. Where do I start?

  • Why my itunes cant open ??

    it says error signature AppName: itunes.exe      AppVer: 10.6.3.25      ModName: unknown ModVer: 0.0.0.0      Offset: 064e1040 i dont know how to fix it if somebody know how to fix this, Please Help me I need my iTunes now ! T_T

  • Amounts in pie charts.

    Hi there. I´m trying to create some pie charts in BIP with MSWord, but I´ve noticed although the source amounts are quantities, only percentages appear in the chart. Can somebody tell me?. I´m blocked by now with it. Thanks a lot. Bye...

  • Cannot e-mail photos from iPhoto

    I have been trying to e-mail a postcard from iphoto and it keeps saying my server is not responding.  What do I do to rectify this problem.