RAC using QFS on Sun Solaris 10 -VIP configuration

Hi DBA's
how to create Virtual IP address in Virtual Box?
I just add in the host file my IP address but i am not able to Ping the Virtual IP address
My host file is as follows. Kindly guide me how to create Virtual IP Address?
bash-3.00# cat /etc/hosts
# Internet host table
::1 localhost
127.0.0.1 localhost
192.168.1.10 rac1.orademo.com rac1
192.168.1.11 rac2.orademo.com rac2
192.168.0.10 rac1-priv.orademo.com rac1-priv
192.168.0.11 rac2-priv.orademo.com rac2-priv
192.168.1.12 rac1-vip.ordemo.com rac1-vip
192.168.1.13 rac2-vip.orademo.com rac2-vip
192.168.1.100 rac-scan.orademo.com rac-scan
192.168.1.6 win
bash-3.00#
Regards,
SG

HI,
Pls mentioned OS and DB version.
Meanwhile check below MOS document for help:-
Modifying the VIP or VIP Hostname of a 10g or 11g Oracle Clusterware Node [ID 276434.1]
Configuring Solaris IP Multipathing (IPMP) for the Oracle 10g VIP [ID 283107.1]
Configuring Linux for the Oracle 10g VIP or private interconnect using bonding driver [ID 298891.1]
Configuring the IBM AIX 5L Operating System for the Oracle 10g VIP [ID 296856.1]
How to Configure Solaris Link-based IPMP for Oracle VIP [ID 730732.1]
Oracle 10g VIP (Virtual IP) changes in Oracle 10g 10.1.0.4 [ID 296878.1]
Thanks,
JD

Similar Messages

RAC using QFS on Sun Solaris 10

Dear DBA's,
I am planning to implement RAC using QFS on Sun Solaris10, i dont have any idea of QFS, kindly provide any document how to use qfs and implement rac using qfs on solaris.
Best Regards,
SG

Please also see these links:
http://www.lmgtfy.com/?q=QFS+Oracle+RAC
http://www.lmgtfy.com/?q=QFS+Oracle+RAC+Oracle+E-Business+Suite
Thanks,
Hussein

11g r2 non rac using asm for sun cluster os (two node but non-rac)

I am going to install grid installation for non-rac using asm for two node sun cluster environment..
How to create candidate disk in solaris cluster (sparc os) to install grid home in asm.. please provide me the steps if anyone knows

Please refer the thread Re: 11GR2 ASM in non-rac node not starting... failing with error ORA-29701
and this doc http://docs.oracle.com/cd/E11882_01/install.112/e24616/presolar.htm#CHDHAAHE

DO I need SFRAC for Oracle 10g RAC on Sun Solaris

My platform is SUN Solaris 10 64 bit on v490 server. On the backend side, we are using EMC CX500 storage. We will use Veritas File system and Veritas CFS.
I would like to ask, Do I must need SFRAC to configure Oracle 10g RAC or Can I just use only Oracle CRS. I do not want to use ASM.
Please advise
Thanks,
Sam..

The VCFS usually requires a Veritas Cluster, thus you would have to use the product combination that is bundled as SFRAC as mentioned before. Metalink in addition says:
10 10gR2 64-bit Veritas Storage Foundation for Oracle RAC 5.0 Certified
There is one exception to this rule: Linux.
Veritas and Oracle support a standalone version of the Veritas Cluster Files System (and only this component) on Linux. This does not hold true for Solaris.
Concluding, if you want to use the VCFS you would need to get a VCS, which then basically means using SFRAC.
However, in this case, as mentioned before, you would not need ASM.

Oracle 9i RAC on Sun Solaris 5.10/64 bit version.Is that supported ?

I want to install Oracle 9i RAC on Sun Solaris 10 64 bit. Is that officially supported ?
I dont this combination on metalink certify matrix

I know we dont get support from oracle.But, you initially mentioned that you couldn't find the required information on metalink, therefore I provided that information, which I thought you were looking for.
Is anybody still using this combination ? Does it work ? yes, we are using it and it has been working fine for over 4 years...of course we patched it to the latest - 9.2.0.8 to be on the supported release/patch.

How to Configure the Eterprise Manager in sun solaris

Hi
Please help me In configuring the enterprise manager
my environment :
2 node RAC in SUN Solaris 9
database :Oracle 10.1.4.0
if any body have documents regarding configuring(order wise steps) for configuring Enterprise Manager

The Oracle docs should help (Oracle® Enterprise Manager Advanced Configuration).

How to configure the network on Sun Solaris 8

The Sun workstation is a license server, and Window NT workstation need to access the license file that located in the sun workstation.
Now the Window NT workstation cannot connect with the sun solaris, and I guess that I need to configure the network on Sun Solaris 8.
Could you please tell me how to do that step by step?
If there is the system tool like the window system to configure the network easily and quickly.
I appreciate it.
Mark

If your sun system is working then probably it has network configured already .You can check it by the following command on the sun.
ifconfig -a
Generally applications asks where license server is located and you need to give the ip-address or host name only . Application docs will give more detail about it.
You can get ip-address from ifconfig comand above.
Hemant Sharma
http://www.adminschoice.com

How to configure tape to sun solaris server?

Hi
We have a tape "Quantum Super DLT 600 tape drive" connected to Sun solaris 9 and working properly.
Now we want to connect and configure it to Sun solaris 10 server. I want to know how we can do it?
I checked in st.conf file , "#tape-config-list=" is commented in both solaris 9 while in solaris 10 it is not there.
I think i will just have to connect the tape to new srver(solaris 10) and do a reconfiguration boot. Right??
Also, what do i need to do for connecting the tape back to solaris 9 server.
Thanks

You really don't need to reboot the server. Connect the tape to the server and type devfsadm -Cv. Then type dmesg and check whether Solaris detect the tape or not.
if not do a reboot and see.
after doing one of above, insert a tape to the tape drive and type "mt stat" and see you got any output about a tape.
Refer Solaris 9 and Solaris 10 System Administration Guides.
Edited by: Thusith.M on Jul 31, 2009 9:24 AM

Can I use coldfusion 8 standard version in Sun / Solaris?

Hi,
I would like to know if I can use coldfusion 8 standard
version in Sun / Solaris
Thank you.

banguitainf wrote:
> Hi,
>
> I would like to know if I can use coldfusion 8 standard
version in Sun / Solaris
No.
http://www.adobe.com/products/coldfusion/systemreqs/#support_matrix
Mack

Now I am using Windows Xp Labview program now i want control the Sun Solaris OS Board.Is it Possible in Windows XP Labview?

Now I am using Windows Xp Labview program now i want control the Sun Solaris OS Board.Is it Possible in Windows XP Labview?

You better should post your question in the LabVIEW forum - this one here is dedicated to LabWindows/CVI...

VIP configuration problem

This is a 2-node installation on SUN solaris SPARC severs(M4000 and E6900).
installion of Oracle CRS(10.2.0.4) and db oracle_home on 2-node solaris 10 SPARC were completed succesfully.
Since the network interface cards on both the servers are different(the NIC name in M4000 is e1000g1,e1000g2 while in E6900 it is ce0,and ce1), we created symbolic links e1000g1,e1000g2 on e6900 server to point to ce1 and ce2. Im trying to configure vips on both the servers and im facing a weird problem.
Both the VIP's are being created in M4000 server instead of one on each server.
ie:
required config:
node1-vip-192.168.1.191
node2-vip 192.168.1.181
but when i run
srvctl modify nodeapps -n node1 -A 192.168.1.191/255.255.255.0/e1000g2
srvctl modify nodeapps -n node2 -A 192.168.1.181/255.255.255.0/e1000g2
Both the VIPS are being created in node1.
the output of crs_stat -t is
Name Type Target State Host
ora....SM1.asm application OFFLINE OFFLINE
ora....ST.lsnr application ONLINE ONLINE node1
ora....est.gsd application ONLINE ONLINE node1
ora....est.ons application ONLINE ONLINE node1
ora....est.vip application ONLINE ONLINE node1
ora....SM2.asm application OFFLINE OFFLINE
ora....T1.lsnr application ONLINE OFFLINE
ora....st1.gsd application ONLINE ONLINE node2
ora....st1.ons application ONLINE ONLINE node2
ora....st1.vip application ONLINE ONLINE node1(Why is this configuring in node1 instead of node2)
im getting the following error in the vip log file
2009-10-26 13:26:31.387: [    RACG][1] [24377][1][ora.node2vip]: Interface e1000g2 checked failed (host=node2 )
Failed to start VIP 192.168.1.181 (host=node2 )
2009-10-26 13:26:31.388: [    RACG][1] [24377][1][ora.node2vip]: clsrcexecut : env ORACLE_CONFIG_HOME=/u01/oracle/product/10.2.0/crs
2009-10-26 13:26:31.388: [    RACG][1] [24377][1][ora.node2vip]: clsrcexecut : cmd = /u01/oracle/product/10.2.0/crs/bin/racgeut -e USRORA_DEBUG=0 54 /u01/o racle/product/10.2.0/crs/bin/racgvip start node2
2009-10-26 13:26:31.388: [    RACG][1] [24377][1][ora.node2vip]: clsrcexecut : rc = 1, time = 5.620s
2009-10-26 13:26:37.106: [    RACG][1] [24377][1][ora.node2vip]: Interface e1000g2 checked failed (host=node2 )
Failed to start VIP 192.168.1.181 (host=node2 )
2009-10-26 13:26:37.106: [    RACG][1] [24377][1][ora.node2vip]: clsrcexecut : env ORACLE_CONFIG_HOME=/u01/oracle/product/10.2.0/crs
2009-10-26 13:26:37.106: [    RACG][1] [24377][1][ora.node2vip]: clsrcexecut : cmd = /u01/oracle/product/10.2.0/crs/bin/racgeut -e USRORA_DEBUG=0 54 /u01/o racle/product/10.2.0/crs/bin/racgvip check node2
2009-10-26 13:26:37.107: [    RACG][1] [24377][1][ora.node2vip]: clsrcexecut: rc = 1, time = 5.718s
2009-10-26 13:26:37.107: [    RACG][1] [24377][1][ora.node2vip]: end for resource = ora.node2vip, action = start, status = 1, time = 11.434s
2009-10-26 13:26:51.177: [    RACG][1] [24664][1][ora.node2vip]: Interface e1000g2 checked failed (host=node2 )
Failed to start VIP 192.168.1.181 (host=node2 )
2009-10-26 13:26:51.178: [    RACG][1] [24664][1][ora.node2vip]: clsrcexecut: env ORACLE_CONFIG_HOME=/u01/oracle/product/10.2.0/crs
2009-10-26 13:26:51.178: [    RACG][1] [24664][1][ora.node2vip]: clsrcexecut : cmd = /u01/oracle/product/10.2.0/crs/bin/racgeut -e USRORA_DEBUG=0 54 /u01/o racle/product/10.2.0/crs/bin/racgvip start node2
Please help
Thanks and Regards,
Bob

I don't think you can simply create a symlink for a device and expect that this will work. For example, ifconfig won't show the 'new' devicename. That's why clusterware fails to bring the VIP up on one host and then it will bring the vip online on the other node (expected behaviour).
One solution that I can think of is to create a new virtual interface on both nodes and assign the same name to both. You could use Solaris IPMP to create a new interface like this:
on M4000:
dladm create-aggr -d e1000g2 1on E6900:
dladm create-aggr -d ce1 1This will create a new interface called aggr1 on both machines so you should be able to define the VIPs like this:
srvctl modify nodeapps -n node1 -A 192.168.1.191/255.255.255.0/aggr1
srvctl modify nodeapps -n node2 -A 192.168.1.181/255.255.255.0/aggr1Bjoern

Installation problem sun solaris 9 x86 on intel

I am trying to install sun solaris 9 x86 intel platform edition on my home pc hp e-vectra, configuration is PIII 800 Mhz, 10 GB HDD, 128 MB Ram, 17" color monitor, but it giving me following error :-
BooT Panic: trap type e, error 0 at 117499
Cr0: 800000011, cr1: 4, cr3: 17e000
Eax: 0, ebx: 7e2c, ecx: 0 edx: 16e350
Es: fffffffe, edi: 17dfe0, ebp: 7e40, esp: 7e20
Entering boot debugger:
Please help me, how can I install sun solaris 9 x86 on my HP E-Vectra PC.
Kalpesh Mehta

I had similar problems several months ago. I suspect this happens when host pc does not have floppy drive(or bios somehow misreports it) as it was in my case. Solaris 8 seems to work fine in the same environment, so I keep using it for now. Possible workaround might be to use DCA from Solaris 8: Installation of Sol9 started just fine after I entered Sol8 DCA and asked it to boot from Sol9 CD.
Hope this problem will be fixed in subsequent Sol9 releases.
Victor

Oracle 10g R2 installation on sun solaris 10 Sparc machine

Hi there,
I encountered the following problem during oracle 10g R2 installation on sun solaris 10 Sparc machine
Error encountered:
Using paramFile: /u01/Oracle/10gr2_db_sol/install/oraparam.ini
Checking installer requirements...
Checking operating system version: must be 5.8, 5.9 or 5.10. Actual 5.10
Passed
Checking Temp space: must be greater than 250 MB. Actual 2266 MB Passed
Checking swap space: must be greater than 500 MB. Actual 2335 MB Passed
Checking monitor: must be configured to display at least 256 colors Failed <<<<
>>> Could not execute auto check for display colors using command /usr/openwin/bin/xdpyinfo. Check if the DISPLAY variable is set.
Some requirement checks failed. You must fulfill these requirements before
continuing with the installation,at which time they will be rechecked.
Continue? (y/n) [n]
The following were the steps taken before encountering the above error
1. logged into a workstation
2. From its xterm terminal I logged to the oracle server via ssh oracle@ip
3. keyed in the following at the command prompt
DISPLAY=machine_name:0.0; export DISPLAY
4. executed the following from the command prompt
./runInstaller
Note: when executing the ./runInstaller, the preinstallation checking just hangs at Checking monitor: must be configured to display at least 256 colors. But the log file shows it failed during preinstallation checking as shown in Error encountered
Please help me with this problem.
Thank you
Ravindran Kanniah

It is because of UNIX shell. I also faced this error during installation.
First check your shell by the following command.
$ echo $SHELL
Then select the below.
For csh shell
$ setenv DISPLAY 192.168.1.128:0.0
$ export DISPLAY
For sh,ksh and bash
$ DISPLAY=192.168.1.128:0.0
$ export DISPLAY
After you do this check the value of DISPLAY variable.
$ echo $DISPLAY
If the DISPLAY variable is set then run ./runInstaller.
One advice: Keep a complete log of your terminal session. This will help you in future :)
-aijaz

How to install Apache Web Server with PHP on Sun Solaris Sparc machine

Hi,
We are trying to install the Apache Web Server and the PHP package on a Sun Solaris Sparc machine running on SunOS 5.8. We are having compilation problems with the source code of both these packages.
Does anybody know if there are ready solaris packages for Apache and PHP available from where we can download and install instead of source code compilation?
Or any instructions / things to watch for when installing Apache with PHP (if anybody has tried installing Apache with PHP on Sun Solaris earlier) is most welcome.
Thanks,
Harish

Apache should be bundled along with Solaris check in "/var/apache" in Solaris 8 and Solaris 9
php is available at www.php.net
I found an old document for installing PHP maybe this will help.
Cheers
-Dhruva
+++++++++++++++++++++++++++++++++++++++++++++++++++++++Installing PHP 3.x for Apache 1.x.x on Solaris
Introduction
This document describes how to install PHP for Apache on Solaris.
You should have Apache installed before trying to install PHP.
If you want to use PHP with MySQL then you must install MySQL first.
Before we Begin
1. These instructions assume that you have Apache installed according to instructions.
Getting PHP
1. You must be logged in as root to perform this installation.
su root
2. I save all my downloads in:
/usr/local/dist
If you don't already have one, you may need to create that directory now:
mkdir /usr/local/dist
3. You can get PHP 3.0.14 from here(www.php.net).
cd /usr/local/dist
ftp ftp.php.net
cd pub/distributions
bin
get php-3.0.14.tar.gz
bye
Installing PHP
1. We will install PHP in /usr/local/build, but use a tricky tar command
to do it in on hit from the download directory:
cd /usr/local/dist
tar xvfz php-3.0.12.tar.gz -C ../build
Compiling PHP
1. First let's get where the action is:
cd /usr/local/build/php-3.0.14
2. You now have 3 options:
* Simple PHP install without MySQL - goto step 3
* Simple PHP install with MySQL - goto step 4
* Custom PHP install - goto step 5
3. Simple PHP install without MySQL. Next, jump to step 6.
./configure --with-apache=../apache_1.3.12
4. Simple PHP install with MySQL. MySQL must be installed before you can configure PHP to use it. I recommend that MySQL should always be reachable with /usr/local/mysql. Even if you install it else where you
should create a symbolic link from /usr/local/mysql. Otherwise the compiler can have problems finding the mysqlclient library. The command
should look like this:
./configure with-mysql=/usr/local/mysql with-apache=../apache_1.3.12
Next, jump to step 6.
5. Custom PHP install. Take a look at the available configuration directives by using this command:
./configure --help
6. Now we can make the PHP executable. This may take a while.
make
7. Now we install the PHP module with:
make install
Adding the PHP Module to Apache
1. Now we have to setup Apache to include the PHP module:
cd ../apache_1.3.12
2. Re-configure Apache to use the PHP module. You should use your previous Apache configure command along with the PHP activate module directive.
You can see your previous Apache configure command by doing:
cat config.status
You can configure Apache using the previous command with the added PHP module by doing:
./config.status --activate-module=src/modules/php3/libphp3.a
If you used the simple Apache install from instructions the command will look like this:
./configure prefix=/usr/local/apache activate-module=src/modules/php3/libphp3.a
3. Make and install Apache with PHP enabled:
make
4. We need to stop the server before installing the files:
/usr/local/apache/bin/apachectl stop
5. Now we can install the new binaries:
make install
6. Start apache again (now running the new php enabled version):
/usr/local/apache/bin/apachectl start
Setting Up PHP
1. We have to tell Apache to pass certain file extensions to PHP. We do this in Apache's httpd.conf file.
cd /usr/local/apache/conf
2. Edit the httpd.conf file. If you do a search for php you will find a couple of commented out lines telling Apache to use the PHP module. You should uncomment them to look like this.
AddType application/x-httpd-php3 .php3
AddType application/x-httpd-php3-source .phps
3. I prefer to use the extension .phtml, you can use whatever extension you like (even .html) by adding lines to httpd.conf like this:
AddType application/x-httpd-php3 .phtml
Check that it Works
1. We have to restart Apache to make these changes take effect on the running server.
cd /usr/local/apache/bin
./apachectl restart
2. Apache should now be running with PHP enabled. The server version should include PHP/3.0b2.
./apachectl status
Apache Server Status for dev.synop.com
Server Version: Apache/1.3.9 (Unix) PHP/3.0.12
Server Built: Oct 25 1999 00:37:07
3. Now it is time to test PHP with a page. The simplest thing to do is create a page called test.php3. My file is here. This file contains the
following text:
<?php phpinfo(); ?>
4. Point your browser at this file on the virtual host which you used:
http://localhost/test.php3

How to connect sun solaris 10 on sparc to the internet?

hello all. i don't know anything about sun solaris 10.
after installing sun solaris 10 into my sparc pc, i need to register it through internet.
but i don't know how to connect to internet through LAN at my campus. =(
Please help me & give me details how to connect to internet?

Go to docs.sun.com and get the "system administration guide: IP services". This will give you info on how to configure the network card and tcp/ip config files. Since you just installed this, you must have told the install process that the system was not connected to the network, otherwise it would have asked you for name service, hostname, etc. and configured this info for you.
First you need to get info from your network/lan admin on an ip address, netmask, gateway, NIS/NIS+/DNS server, etc.
If the LAN uses DHCP, then see the "DHCP" section of the IP Services guide.
If the LAN uses issued IP addresses, then with the info provided by your network admin in hand, you can do 1.) sys-unconfig to force the system to return to the part of the install where it will ask you for the info and configure it for your -OR- take the info provided and configure the appropriate files specified in the IP Services guide.

RAC using QFS on Sun Solaris 10 -VIP configuration

Similar Messages

Maybe you are looking for