Radeon 7500 vs onboard Geforce2MX

I'm considering getting a ATI All-In-Wonder Radeon 7500 for my nForce1. Does anyone know whether this card is faster or slower than the onboard Geforce2MX? I really hate to take a hit in performance playing Counter Strike or Medal of Honor.
I found some performance scores on extremetech.com and tomshardware.com, but they were comparing to the AIW Radeon 8500 and the Geforce Personal Cinema which had a worse score than the AIW7500. AIW8500 is a bit pricey for my budget and the $400 AIW9700Pro is way out of my league.
BTW, would BIOS auto disable onboard Geforce2MX and free up 32Meg RAM when AGP board is installed?

Hello!
I had a radeon 7500 64mb ddr in my nforce.
Counter strike runs a bit better using the onboard gfx gf2.
With the radeon 7500 player and gun model details is a bit blurred, this is due to cs not the card. And fps drops slightly more buts it isnt that bad. CS has always been  with ATi.
For games like sof2 the, using high detail 1024x768 in 32bit colour the radeon 7500 really is quite good, a million times better than the onbaord.
Its far better than the onboard video. I would use it.
But i sold it to my bro for £15 eheh!
Yes the onboard gfx will automatically disable its self and free the 32 mb its uses.
Also set you agp aperature size to 64MB, anything lower on the radeon 7500 and it will run slow.
I benchmarked my 7500 on default settings on the nforce around about 5200.
Tango

Similar Messages

  • Having trouble installing Radeon 7500 into K7T266 Pro

    I am having all sorts of problems switching from my nVidia TNT 2 (MaxiGamer Cougar) video card to my new Radeon 7500.  I am running an AMD Athlon 1400 with 512 MB DDR RAM.  
    I have the K7T266 Pro (MS-6380) chipset.
    Can anyone think of what I am missing here.  I think I have all the updates AGP drivers I need but I am not sure.  I get lock ups prior to windows starting everytime. Even in safe mode.
    Grrrr.

    I ended having to format my c drive.  Windows began doing some really funny things and then never started again with old or new video cards.  I have re-installed windows but now sometimes my monitor stays blank when I start the computer.  It is supposed to wake itself up but when it does, it has no picture.  To solve this I shut down and flick the switch on the back and discharge everything.  It then works again for another few times.  Do you think this may be a problem with my power supply?  I have an Enermax 350W.  I bought it when I built the computer and figured it would have plenty of juice.
    Thanks for you help

  • K7T266 Pro2 and ATI Radeon 7500?

    Ok, first off, I have been in the technical field for about 12 years, so there is no need to "dumb down" your responses...
    All right. I've got the above board, and it has been working fine up until I bought a new ATI Radeon 7500 vid card. I shut down the computer, disconnected the power supply, and removed my old vid card (which, btw, was working fine, but it was an 8MB old card). Then I installed the new vid card and restarted the computer. At this point, it promptly refused to even post. The monitor light flashed as if it were in standby, and there were no sounds from the board. Everything is still recieving power, so that's not the problem. The "D-bracket" showed 1-Red, 2-Green, 3 and 4-Red. Now this says that there is something wrong with the memory (?). Switched RAM chips, then the d-bracket shows all red = CPU problems? So, I shut it down and waited for a bit. Restarted it again, and the same lighting on the d-bracket, with 1,3,4-Red, and 2-Green. Now the motherboard repeatedly emits 3 fast beeps, then a pause, then 3 fast beeps, etc.. So, I put in the old video card, and the same thing occurred, in a RANDOM order. So, keeping in mind that NOTHING other than the vid card was removed OR touched before the problem occurred. RANDOM errors are NOT the way to run technical items. RANDOM problems are meant for EXPERIMENTAL items...
    I would really hate to have to send in my motherboard to MSI to get it fixed (on warranty), because my business RELIES on my ability to access my computer, and 3 months computer-less is unacceptable. If there is not some LOGICAL thing that may be wrong, I will have to simply go out and buy another new motherboard. Unfortunate as it is, I am afraid that it will NOT be an MSI, because all I have ever had is problems with this board, and the lack of technical support is a real problem.
    Any ideas will be tried, and I will post results as soon as I see the suggestion. Thanks.

    well if you can and I know I would take the ATI card back and get a refund and by a nvidia I got a $250 ATI AIW setting on my file cabnet as a paper wait
    one other thing you could try if you have one a old PCI video card remove the ATi card put a PCi video card in and try to boot useing it if that works go into bios setup and under advanced chipset settings make sure all the agp settings are set to auto I know I had this problem before I had the AGP driver setting set manule to a setting that would not work with my video card and clearing cmos would not reset this setting to auto.
    I had to use a old pci card to boot so I could reset this to auto.

  • [Solved] Conflict: ATI Radeon HDMI vs onboard sound crashes PulseAudio

    Firstly, please excuse my ignorance about audio issues!
    I have a mate running Arch who has an ATI Radeon HD5450 graphics card (using radeon driver) and onboard sound also. He doesn't want to use the graphics card for audio purposes at all. He's getting (seemingly) random switches between PulseAudio thinking its default audio sink is the onboard sound and the graphics card. When the latter happens, PulseAudio crashes out.
    (Tried setting the kernel boot parameter 'radeon.audio=1' to try and make the HDMI audio work, but to no avail. Though card is in radeon driver matrix saying HDMI audio feature should work with this card.)
    Issuing these commands usually gets things up and running again:
    pulseaudio --start && pacmd set-default-sink alsa_output.xxxxx.analog-stereo
    where alsa_output.xxxxx.analog-stereo is the appropriate string from the 'Default Sink' line of the ouput from the command:
    pactl stat
    Tried switching the HDMI input/output off using pavucontrol but after an indeterminate time it creeps back and kills off PulseAudio.
    Can the graphics card be blacklisted as a soundcard by PulseAudio or Alsa in some way?
    Any ideas to resolve this most welcome!
    PS: Had a look through the Arch Wiki on PulseAudio and it helped quite a bit with understanding pactl and pacmd commands.
    Edit @29/01/14: Problem solved - by going deeper to kernel level!
    From the wiki:
    If both devices use the same module then we can use the *enable* parameter from snd-hda-intel module, it's an array of booleans that can enable/disable the desired sound card [put in /etc/modprobe.d/modprobe.conf]:
    e.g
    options snd-hda-intel enable=1,0
    Useful commands to check situation:
    cat /proc/asound/cards
    cat /proc/asound/modules
    aplay -l
    Last edited by ninian (2014-01-29 23:14:35)

    Silex89 wrote:
    Hi there!
    If you're using the latest kernel spin (3.13), you don't have to really put that kernel parameter in your bootloader config anymore because it's enabled by default already. Which DE are you using? GNOME, GNOME Flashback, Cinnamon and Unity have all integrated with pulseaudio and no extra configuration is needed. If you're using Xfce, LXDE, KDE or any other WM/DE, you'll have to install pulseaudio-alsa and alsa-utils to get it working. That made my HDMI audio work out of the box on my ancient KDE session with the open source driver.
    I hope this helps!
    Best of Luck
    Hi,
    okay I just removed the kernel option, thanks for the advice!
    I'm using xfce and I already had installed pulseaudio-alsa and alsa-utils, anyway the strange thing is that before switching to headphones (on the other card) it worked, but now it seems that is dead...
    Thank you for helping!

  • How to get the Windows Vista Driver for ATI Radeon 7500 card?

    How to get the Windows Vista Driver for ATI Radeon 7500 card?
    I am using a IBM Thinkpad T42 with a 32Mb ATI Radeon 7500 graphic card AGP.
    Is there any Vista 32-bit driver to update my card so that this system support Aero effect?
    Thank you.
    regards,
    W. Thong

    wthong wrote:
    How to get the Windows Vista Driver for ATI Radeon 7500 card?
    The Radeon 9000 driver works for the Radeon 7500 card.  I have successfully used it on a T43 with Vista Ultimate x86
    wthong wrote:
    Is there any Vista 32-bit driver to update my card so that this system support Aero effect?
    Unfortunately no.  The Radeon 9000 driver should bring your graphics score up to close to 2, but it will not get it high enough to enable Aero support.
    Cheers,
    Bill
    I don't work for Lenovo

  • 15" Studio Flat ADC Display PowerMac G4 400 MHz Radeon 7500 no video

    Purchased a video card - Radeon 7500
    ATI Radeon 7500 32MB ADC VGA MAC Edition video card
    Computer is PowerMac G4 AGP Graphics (CPU type 2.7) 1 MB Level 2 cache
    VGA works fine.
    ADC is not operational. 15 inch (clear case) display not getting a signal, Profiler not showing any display connected to the ATY,Bluestone_B
    SYSTEM REQUIREMENTS (VIDEO CARD)
    Power Mac™ G4 with AGP 2X or AGP 2X/4X universal slot
    DVD playback requires DVD drive
    !!!!!!!!! WHATS WRONG?
    PowerMac G4 400 MHz   Mac OS X (10.3.9)  

    Hi Gary,
    The G4 AGP graphics model is pre-ADC and its motherboard will not support a video card with a native ADC port. The ADC ports on such cards draw their power and USB feed via an extra leg on the card that fits into an extra slot at one end of the AGP slot on the computer motherboard. Your computer does not have this extra slot.
    To run an ADC display off your computer, you can run a video card with a DVI output, then use a DVI to ADC adaptor such as this one:
    http://www.drbott.com/prod/db.lasso?code=0111-DVAD
    You can use VGA to ADC adaptors, but they are much more expensive (than a DVI to ADC adaptor plus another video card), and don't give as good a result.
    Cheers!
    Karl

  • Installing Radeon 7500

    I am going to install a Radeon 7500 PCI card is there any thing I need to do before I in stall it on this MS6378 board?

    thank u for the support. I am also increasing my memory from 256 to 334 megs. :D

  • Radeon 7500 AGP identification problem

    I think I may have asked before, but I don't remember.  My system specs are listed below.  My problem is that my Radeon 7500 AGP card shows up as PCI under properties in the hardware listing.  Why is this?  Is it a problem?
    Thanks

    Quote
    Originally posted by Rob454
    How many IRQs does your device manager go up to?
    More than 16?
    You might have to enable APIC to get more irqs for your devices. But could cause trouble.  
    Also here is the newest Catylist drivers from Ati
    They are newer than on the Power color site.
    http://mirror.ati.com/support/drivers/powered.html
    I momentarily lost track of this thread. :D
    Yes, more than 16.  I'm pretty sure there are 22.  I don't have any sharing now except for the USB, they all share the same IRQ.  I don't have any device conflicts, so that's good.
    Thanks for the link.

  • Radeon 7500 Normal AGP card Without ADC (Used before on Windows Vista PC)

    Dear ...
    i read in some articals on internet that you can use this kind of Cards "Radeon 7500 Normal AGP card Without ADC (Used before on Windows Vista PC)" with Mac G4 Quicksliver 733Mhz ... just u have to install it and leave Machine on for sometimes till dedicated it is thatture ?
    Message was edited by: waldhin

    A Radeon 7500 (as well as any other AGP graphics card) that was removed from a PC must have its EEPROM chip re-programmed to function in an Apple computer. This is usually done while the card is installed in a PC, using a compatible flash utility program and the correct ROM code taken from the Mac version of the same card.

  • 845e max and radeon 7500

    ok my problem is that i just bought this video card(ati radeon 7500) and on my mobo it says only use agp 4x 1.5v only but this card is a 4x/2x. it also says in my mobo manuel to use a 2x/4x card switch to 4x in the jumpers. my problem is that there is no jumpers on the card so what do i do. i dont want to distroy my mobo so what do i do.

    I am pretty sure that ATI Radeon 7500 is a 1.5V 4X-compliant card. Just put it in and try it out. The motherboard has this routing thing that won't boot the computer if you have a 3.3V AGP card installed anyway, so you are safe. 8)

  • Radeon 7500 Mac Edition Quicksilver 2001

    I have installed a Radeon 7500 Mac Edition video card in my 2001 Quicksilver. This card was an option in the 2002 Quicksilver. I am having problems installing OSX software and notice that Mac warns that it may be necessary to install the original graphics card for installation. I no longer have my original card.
    Is the 7500 compatible with my machine? In general the card works fine with my dual moniotrs but I do have problems running iChat with frequent freezes and dropped service.
    If the 7500 is not a good choice for my machine what should I buy for dual monitor support and Mac compatibility?

    Hi,
    The 7500 Mac Edition is kind of an oddball. Good card, but ATI doesn't support it with Mac Drivers. You can download the latest Radeon Universal Driver ROM's from here;
    https://support.ati.com/ics/support/default.asp?deptID=894&task=knowledge&folder ID=27
    Run the program and see if it helps.
    If not, depending on budget, I'd get an ATI 9800 Pro Mac Edition, either the 128MB or 256MB. You will then have the best video card available for a G4, the QS will handle it just fine. I just noticed that Newegg.com has the 256MB available for $199 after rebate, a deal -for the best.
    Regards,
    Dave

  • K7-Master 6341 &ATI Radeon 7500 4x/"1x2x" AGP Video Issue (XP Crashes

    I know the K7-master is old.... but maybe someone will know how to help me keep my PC from crashing if I put the bios setting on 4x instead of 1x/2x. Thanks.
    System: MSI K7-Master (MS6341)
    BIOS V. 1.5 (Newest)
    OS: WindowsXP(SP1)
    CPU: AthlonXP 2000+ Model 6
    AMD AGP Miniport V5.33 Installed
    Radeon 7500 AGP 64Mb
    Video Drivers V6.13.10.6166
    Display Driver V7.76-020815b-005727c-ATI
    Control Panel V6.13.10.3027
    Catalyst V02.3
    Clean XP install.... no software... only AGP Card in Machine... no PCI or other cards.
    Card Bought New in Box
    Issue: WindowsXP crashes on boot (apprx 4seconds into loading desktop)and recovers to largest resuloution 640x??? 4 colors if BIOS setting for "AGP Data Transfer Mode"="4x" If BIOS is set to "1x/2x" system boots and runs without error.
    ErrorMessages: "Windows has revovered from a serious error" Possible cause "ATI Radeon 7500 display driver" Sent to Microsoft with no help back from Microsoft.
    Current System Bios Settings and Values.
    "Video BIOS Shadow" = "Disabled" (Possible Settings, Enabled-Disabled)
    "System BIOS Cachable"="Disabled" (Enabled-Disabled)
    "Video RAM Cacheable"="Disabled" (Enabled-Disabled)
    "Memory Hole at 15M-16M"="Disabled" (Enabled,Disabled)
    "AGP Aperture Size MB"="64" (32,64,128,256)
    "AGP ISA Aliasing" = "Disabled" (Enabled,Disabled) I dont know what that is anyway.
    "AGP Secondary Lat Timer" = "20h" (00h,20h,40h,60h,80h,C0h,FFh)Unknown what this is too.
    "AGP Fast Write"= "Disabled" (Enabled,Disabled)
    "AGP Data Transfer Mode" = ("4x" Crashes & "1x/2x" No system crash)
    "Init Display First" = "AGP" (PCI Slot,AGP)
    "PNP OS Installed" ="YES" (No,Yes)
    "Resources Controlled By"= "AUTO ESCD"
    "PCI/VGA Palette Snoop" = "Disabled" (Enable,Disable)
    I know this is alot of information I just hope you can help me get my ATI Radeon 7500 transfering at 4x bus speed. I know the card is "older" than the super powerful ones but I want to get everyting out of this card I paid for. I thank you in advance for your help. Please let me know if you need any more information.
    Thanks,
    Dan

    Quote
    Originally posted by nutt2118
    Here is part of the message from ATI about this problem that I need help with.
    "Try lowering the AGP support (i.e. from AGP 4X to AGP 2X). If this resolves
    the issue, you may consider contacting the motherboard/chipset vendor for more
    information regarding the GART support available on the motherboard/chipset."
    Does the MS-6341 K7-Master support "GART" and what is "GART"
    Thanks,
    Dan
    I returned my Nvidia GeForce4 Ti4600 PNY Verto back to PNY last year, after I had it for a few months, and it kept crashing at AGP 4x. They sent me a new one, I tried it at 4x, with the latest Nvidia Detonator drivers, I have tried it under fresh installs of Windows 2000 SP3, and WindowsXP, both crashing when the card is set to 4x. I believe there is major bugs in this board and it does not truly support AGP 4x. I am goin to try and RMA my board back to MSI, demanding a board that can support my card, or a suitable replacement that will support my current CPU and memory. This is the first MB I ever bought from MSI, and depending on how they resolve this situation, it will probably be the last. This is the 10th machine I have built on my own, I have just not had to time to deal with this issue, and have dealt with it at AGP 2x, but it is slow as hell, especially with games like Battlefield 1942.

  • Mobility Radeon 7500 OpenGL issues

    Whenever I attempt to use anything involving openGL, my CPU usage hits 100%. Complex openGL programs will drop to a framerate of less than 10, and sometimes crash Xorg.  How can I fix this?
    General system info:
    lspci
    00:00.0 Host bridge: Intel Corporation 82845 845 [Brookdale] Chipset Host Bridge (rev 04)
    00:01.0 PCI bridge: Intel Corporation 82845 845 [Brookdale] Chipset AGP Bridge (rev 04)
    00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB Controller #1 (rev 02)
    00:1d.1 USB Controller: Intel Corporation 82801CA/CAM USB Controller #2 (rev 02)
    00:1d.2 USB Controller: Intel Corporation 82801CA/CAM USB Controller #3 (rev 02)
    00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 42)
    00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 02)
    00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 Controller (rev 02)
    00:1f.3 SMBus: Intel Corporation 82801CA/CAM SMBus Controller (rev 02)
    00:1f.5 Multimedia audio controller: Intel Corporation 82801CA/CAM AC'97 Audio Controller (rev 02)
    00:1f.6 Modem: Intel Corporation 82801CA/CAM AC'97 Modem Controller (rev 02)
    01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500]
    02:00.0 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller (rev 01)
    02:00.1 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller (rev 01)
    02:02.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
    02:08.0 Ethernet controller: Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller (rev 42)
    lsmod
    Module Size Used by
    ipv6 279604 16
    oss_usb 106284 2
    oss_ich 18832 4
    osscore 552820 4 oss_usb,oss_ich
    ext2 68964 1
    fan 4448 0
    fuse 64856 2
    arc4 1756 2
    ecb 2812 2
    b43 137208 0
    radeon 666112 2
    ttm 37164 1 radeon
    joydev 10528 0
    drm 156160 4 radeon,ttm
    i2c_algo_bit 5888 1 radeon
    e100 34308 0
    ssb 45988 1 b43
    ppdev 7008 0
    yenta_socket 25384 2
    rsrc_nonstatic 12316 1 yenta_socket
    mii 4892 1 e100
    thinkpad_acpi 67988 0
    battery 10816 0
    nvram 6984 1 thinkpad_acpi
    video 20116 0
    output 2908 1 video
    pcmcia 36168 2 b43,ssb
    parport_pc 37060 1
    irtty_sir 5564 0
    sir_dev 11712 1 irtty_sir
    psmouse 60084 0
    ac 4224 0
    processor 36076 1
    iTCO_wdt 11072 0
    iTCO_vendor_support 3136 1 iTCO_wdt
    mac80211 155788 1 b43
    irda 126744 1 sir_dev
    crc_ccitt 1724 1 irda
    thermal 13912 0
    uhci_hcd 23692 0
    button 5612 0
    ehci_hcd 36620 0
    serio_raw 5792 0
    shpchp 34384 0
    intel_agp 28604 1
    lp 9732 0
    parport 34412 3 ppdev,parport_pc,lp
    evdev 10240 15
    cfg80211 90364 2 b43,mac80211
    pci_hotplug 28732 1 shpchp
    pcspkr 2492 0
    i2c_i801 9616 0
    i2c_core 21808 4 radeon,drm,i2c_algo_bit,i2c_i801
    rfkill 19696 2 thinkpad_acpi,cfg80211
    sg 27728 0
    agpgart 32660 3 ttm,drm,intel_agp
    led_class 4000 2 b43,thinkpad_acpi
    usbcore 154032 5 oss_usb,uhci_hcd,ehci_hcd
    pcmcia_core 35920 5 b43,ssb,yenta_socket,rsrc_nonstatic,pcmcia
    rtc_cmos 11344 0
    rtc_core 17976 1 rtc_cmos
    rtc_lib 2524 1 rtc_core
    ext4 334112 2
    mbcache 7104 2 ext2,ext4
    jbd2 82016 1 ext4
    crc16 1660 1 ext4
    sr_mod 16644 0
    cdrom 36032 1 sr_mod
    sd_mod 28344 5
    pata_acpi 4252 0
    ata_piix 23268 4
    ata_generic 4704 0
    libata 169548 3 pata_acpi,ata_piix,ata_generic
    floppy 56356 0
    scsi_mod 112468 4 sg,sr_mod,sd_mod,libata
    dmesg
    Linux version 2.6.31-ARCH (root@architect) (gcc version 4.4.2 (GCC) ) #1 SMP PREEMPT Tue Nov 10 19:48:17 CET 2009
    KERNEL supported cpus:
    Intel GenuineIntel
    AMD AuthenticAMD
    NSC Geode by NSC
    Cyrix CyrixInstead
    Centaur CentaurHauls
    Transmeta GenuineTMx86
    Transmeta TransmetaCPU
    UMC UMC UMC UMC
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
    BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000003ff70000 (usable)
    BIOS-e820: 000000003ff70000 - 000000003ff7e000 (ACPI data)
    BIOS-e820: 000000003ff7e000 - 000000003ff80000 (ACPI NVS)
    BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
    BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
    DMI present.
    last_pfn = 0x3ff70 max_arch_pfn = 0x100000
    MTRR default type: uncachable
    MTRR fixed ranges enabled:
    00000-9FFFF write-back
    A0000-BFFFF uncachable
    C0000-CFFFF write-protect
    D0000-DBFFF uncachable
    DC000-DFFFF write-back
    E0000-FFFFF write-protect
    MTRR variable ranges enabled:
    0 base 000000000 mask FC0000000 write-back
    1 base 03FF80000 mask FFFF80000 uncachable
    2 disabled
    3 disabled
    4 disabled
    5 disabled
    6 disabled
    7 disabled
    x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    e820 update range: 0000000000002000 - 0000000000006000 (usable) ==> (reserved)
    Scanning 1 areas for low memory corruption
    modified physical RAM map:
    modified: 0000000000000000 - 0000000000002000 (usable)
    modified: 0000000000002000 - 0000000000006000 (reserved)
    modified: 0000000000006000 - 000000000009f000 (usable)
    modified: 000000000009f000 - 00000000000a0000 (reserved)
    modified: 00000000000dc000 - 0000000000100000 (reserved)
    modified: 0000000000100000 - 000000003ff70000 (usable)
    modified: 000000003ff70000 - 000000003ff7e000 (ACPI data)
    modified: 000000003ff7e000 - 000000003ff80000 (ACPI NVS)
    modified: 000000003ff80000 - 0000000040000000 (reserved)
    modified: 00000000ff800000 - 0000000100000000 (reserved)
    initial memory mapped : 0 - 01800000
    init_memory_mapping: 0000000000000000-00000000377fe000
    0000000000 - 0000400000 page 4k
    0000400000 - 0037400000 page 2M
    0037400000 - 00377fe000 page 4k
    kernel direct mapping tables up to 377fe000 @ 7000-c000
    RAMDISK: 3fea7000 - 3ff5fb2e
    Allocated new RAMDISK: 00100000 - 001b8b2e
    Move RAMDISK from 000000003fea7000 - 000000003ff5fb2d to 00100000 - 001b8b2d
    ACPI: RSDP 000f7010 00024 (v02 IBM )
    ACPI: XSDT 3ff731cd 0004C (v01 IBM TP-1I 00002080 LTP 00000000)
    ACPI: FACP 3ff73300 00081 (v01 IBM TP-1I 00002080 IBM 00000001)
    ACPI: DSDT 3ff733e7 0AAD5 (v01 IBM TP-1I 00002080 MSFT 0100000D)
    ACPI: FACS 3ff7f000 00040
    ACPI: SSDT 3ff733b4 00033 (v01 IBM TP-1I 00002080 MSFT 0100000D)
    ACPI: ECDT 3ff7debc 00052 (v01 IBM TP-1I 00002080 IBM 00000001)
    ACPI: TCPA 3ff7df0e 00032 (v01 IBM TP-1I 00002080 PTL 00000001)
    ACPI: BOOT 3ff7dfd8 00028 (v01 IBM TP-1I 00002080 LTP 00000001)
    135MB HIGHMEM available.
    887MB LOWMEM available.
    mapped low ram: 0 - 377fe000
    low ram: 0 - 377fe000
    node 0 low ram: 00000000 - 377fe000
    node 0 bootmap 00008000 - 0000ef00
    (9 early reservations) ==> bootmem [0000000000 - 00377fe000]
    #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
    #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
    #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
    #3 [0001000000 - 000156da44] TEXT DATA BSS ==> [0001000000 - 000156da44]
    #4 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000]
    #5 [000156e000 - 0001574128] BRK ==> [000156e000 - 0001574128]
    #6 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
    #7 [0000100000 - 00001b8b2e] NEW RAMDISK ==> [0000100000 - 00001b8b2e]
    #8 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000]
    Zone PFN ranges:
    DMA 0x00000000 -> 0x00001000
    Normal 0x00001000 -> 0x000377fe
    HighMem 0x000377fe -> 0x0003ff70
    Movable zone start PFN for each node
    early_node_map[3] active PFN ranges
    0: 0x00000000 -> 0x00000002
    0: 0x00000006 -> 0x0000009f
    0: 0x00000100 -> 0x0003ff70
    On node 0 totalpages: 261899
    free_area_init_node: node 0, pgdat c141b740, node_mem_map c1575000
    DMA zone: 32 pages used for memmap
    DMA zone: 0 pages reserved
    DMA zone: 3963 pages, LIFO batch:0
    Normal zone: 1744 pages used for memmap
    Normal zone: 221486 pages, LIFO batch:31
    HighMem zone: 271 pages used for memmap
    HighMem zone: 34403 pages, LIFO batch:7
    Using APIC driver default
    ACPI: PM-Timer IO Port: 0x1008
    SMP: Allowing 1 CPUs, 0 hotplug CPUs
    Local APIC disabled by BIOS -- you can enable it with "lapic"
    APIC: disable apic facility
    nr_irqs_gsi: 16
    PM: Registered nosave memory: 0000000000002000 - 0000000000006000
    PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000
    PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
    Allocating PCI resources starting at 40000000 (gap: 40000000:bf800000)
    NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
    PERCPU: Embedded 14 pages at c1d7a000, static data 34332 bytes
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259852
    Kernel command line: root=/dev/disk/by-uuid/ce79e597-2b00-4812-95b4-eda62758ab6c ro vga=792 nomodeset
    PID hash table entries: 4096 (order: 12, 16384 bytes)
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    Initializing HighMem for node 0 (000377fe:0003ff70)
    Memory: 1031828k/1048000k available (3111k kernel code, 15416k reserved, 1120k data, 416k init, 138696k highmem)
    virtual kernel memory layout:
    fixmap : 0xfff1e000 - 0xfffff000 ( 900 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
    lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
    .init : 0xc1422000 - 0xc148a000 ( 416 kB)
    .data : 0xc1309ddd - 0xc1421ea8 (1120 kB)
    .text : 0xc1000000 - 0xc1309ddd (3111 kB)
    Checking if this processor honours the WP bit even in supervisor mode...Ok.
    SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    NR_IRQS:512
    Fast TSC calibration using PIT
    Detected 2192.708 MHz processor.
    Console: colour dummy device 80x25
    console [tty0] enabled
    Calibrating delay loop (skipped), value calculated using timer frequency.. 4387.14 BogoMIPS (lpj=7309026)
    Security Framework initialized
    Mount-cache hash table entries: 512
    CPU: Trace cache: 12K uops, L1 D cache: 8K
    CPU: L2 cache: 512K
    CPU: Hyper-Threading is disabled
    mce: CPU supports 4 MCE banks
    ------------[ cut here ]------------
    WARNING: at arch/x86/kernel/apic/apic.c:247 native_apic_write_dummy+0x4b/0x60()
    Hardware name: 236686U
    Modules linked in:
    Pid: 0, comm: swapper Not tainted 2.6.31-ARCH #1
    Call Trace:
    [<c10464da>] ? warn_slowpath_common+0x7a/0xc0
    [<c101f2ab>] ? native_apic_write_dummy+0x4b/0x60
    [<c1046540>] ? warn_slowpath_null+0x20/0x40
    [<c101f2ab>] ? native_apic_write_dummy+0x4b/0x60
    [<c1016601>] ? intel_init_thermal+0xd1/0x1d0
    [<c10149c3>] ? mce_init+0xc3/0xf0
    [<c10ed693>] ? __kmalloc+0x93/0x210
    [<c1015bc5>] ? mce_intel_feature_init+0x15/0x70
    [<c13014ed>] ? mcheck_init+0x261/0x2b5
    [<c12ff55a>] ? identify_cpu+0x377/0x386
    [<c10ecabf>] ? kmem_cache_alloc+0x6f/0x170
    [<c1429dc9>] ? identify_boot_cpu+0xa/0x1e
    [<c1429f90>] ? check_bugs+0x14/0x108
    [<c109add0>] ? __delayacct_tsk_init+0x20/0x50
    [<c1422a31>] ? start_kernel+0x332/0x353
    [<c14224f0>] ? unknown_bootoption+0x0/0x1bd
    ---[ end trace a7919e7f17c0a725 ]---
    CPU0: Thermal monitoring enabled (TM1)
    Performance Counters: no PMU driver, software counters only.
    Checking 'hlt' instruction... OK.
    SMP alternatives: switching to UP code
    Freeing SMP alternatives: 11k freed
    ACPI: Core revision 20090521
    ACPI: setting ELCR to 0200 (from 0800)
    weird, boot CPU (#0) not listed by the BIOS.
    SMP motherboard not detected.
    Local APIC not detected. Using dummy APIC emulation.
    SMP disabled
    Brought up 1 CPUs
    Total of 1 processors activated (4387.14 BogoMIPS).
    CPU0 attaching NULL sched-domain.
    Booting paravirtualized kernel on bare hardware
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: PCI BIOS revision 2.10 entry at 0xfd8fe, last bus=8
    PCI: Using configuration type 1 for base access
    bio: create slab <bio-0> at 0
    ACPI: EC: EC description table is found, configuring boot EC
    ACPI: EC: non-query interrupt received, switching to interrupt mode
    ACPI: Interpreter enabled
    ACPI: (supports S0 S3 S4 S5)
    ACPI: Using PIC for interrupt routing
    ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
    ACPI: EC: driver started in interrupt mode
    ACPI: Power Resource [PUBS] (on)
    ACPI: ACPI Dock Station Driver: 3 docks/bays found
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    pci 0000:00:00.0: reg 10 32bit mmio: [0xe0000000-0xe3ffffff]
    pci 0000:00:1d.0: reg 20 io port: [0x1800-0x181f]
    pci 0000:00:1d.1: reg 20 io port: [0x1820-0x183f]
    pci 0000:00:1d.2: reg 20 io port: [0x1840-0x185f]
    pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
    pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH4 GPIO
    pci 0000:00:1f.1: reg 10 io port: [0x1f0-0x1f7]
    pci 0000:00:1f.1: reg 14 io port: [0x3f4-0x3f7]
    pci 0000:00:1f.1: reg 18 io port: [0x170-0x177]
    pci 0000:00:1f.1: reg 1c io port: [0x374-0x377]
    pci 0000:00:1f.1: reg 20 io port: [0x1860-0x186f]
    pci 0000:00:1f.1: reg 24 32bit mmio: [0x000000-0x0003ff]
    pci 0000:00:1f.3: reg 20 io port: [0x1880-0x189f]
    pci 0000:00:1f.5: reg 10 io port: [0x1c00-0x1cff]
    pci 0000:00:1f.5: reg 14 io port: [0x18c0-0x18ff]
    pci 0000:00:1f.6: reg 10 io port: [0x2400-0x24ff]
    pci 0000:00:1f.6: reg 14 io port: [0x2000-0x207f]
    pci 0000:01:00.0: reg 10 32bit mmio: [0xe8000000-0xefffffff]
    pci 0000:01:00.0: reg 14 io port: [0x3000-0x30ff]
    pci 0000:01:00.0: reg 18 32bit mmio: [0xd0100000-0xd010ffff]
    pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
    pci 0000:01:00.0: supports D1 D2
    pci 0000:00:01.0: bridge io port: [0x3000-0x3fff]
    pci 0000:00:01.0: bridge 32bit mmio: [0xd0100000-0xd01fffff]
    pci 0000:00:01.0: bridge 32bit mmio pref: [0xe8000000-0xefffffff]
    pci 0000:02:00.0: reg 10 32bit mmio: [0x50000000-0x50000fff]
    pci 0000:02:00.0: supports D1 D2
    pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:02:00.0: PME# disabled
    pci 0000:02:00.1: reg 10 32bit mmio: [0x51000000-0x51000fff]
    pci 0000:02:00.1: supports D1 D2
    pci 0000:02:00.1: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:02:00.1: PME# disabled
    pci 0000:02:02.0: reg 10 32bit mmio: [0xd0200000-0xd0201fff]
    pci 0000:02:08.0: reg 10 32bit mmio: [0xd0202000-0xd0202fff]
    pci 0000:02:08.0: reg 14 io port: [0x8000-0x803f]
    pci 0000:02:08.0: supports D1 D2
    pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:02:08.0: PME# disabled
    pci 0000:00:1e.0: transparent bridge
    pci 0000:00:1e.0: bridge io port: [0x4000-0x8fff]
    pci 0000:00:1e.0: bridge 32bit mmio: [0xd0200000-0xdfffffff]
    pci 0000:00:1e.0: bridge 32bit mmio pref: [0xf0000000-0xf7ffffff]
    pci_bus 0000:00: on NUMA node 0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
    PCI: Using ACPI for IRQ routing
    NetLabel: Initializing
    NetLabel: domain hash size = 128
    NetLabel: protocols = UNLABELED CIPSOv4
    NetLabel: unlabeled traffic allowed by default
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp: PnP ACPI: found 13 devices
    ACPI: ACPI bus type pnp unregistered
    system 00:00: iomem range 0x0-0x9ffff could not be reserved
    system 00:00: iomem range 0xc0000-0xc3fff could not be reserved
    system 00:00: iomem range 0xc4000-0xc7fff could not be reserved
    system 00:00: iomem range 0xc8000-0xcbfff could not be reserved
    system 00:00: iomem range 0xcc000-0xcffff could not be reserved
    system 00:00: iomem range 0xdc000-0xdffff could not be reserved
    system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
    system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
    system 00:00: iomem range 0xe8000-0xebfff could not be reserved
    system 00:00: iomem range 0xec000-0xeffff could not be reserved
    system 00:00: iomem range 0xf0000-0xfffff could not be reserved
    system 00:00: iomem range 0x100000-0x3fffffff could not be reserved
    system 00:00: iomem range 0xfec00000-0xffffffff could not be reserved
    system 00:02: ioport range 0x1000-0x107f has been reserved
    system 00:02: ioport range 0x1180-0x11bf has been reserved
    system 00:02: ioport range 0x15e0-0x15ef has been reserved
    system 00:02: ioport range 0x1600-0x167f has been reserved
    pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
    pci 0000:00:01.0: IO window: 0x3000-0x3fff
    pci 0000:00:01.0: MEM window: 0xd0100000-0xd01fffff
    pci 0000:00:01.0: PREFETCH window: 0xe8000000-0xefffffff
    pci 0000:02:00.0: CardBus bridge, secondary bus 0000:03
    pci 0000:02:00.0: IO window: 0x004000-0x0040ff
    pci 0000:02:00.0: IO window: 0x004400-0x0044ff
    pci 0000:02:00.0: PREFETCH window: 0xf0000000-0xf3ffffff
    pci 0000:02:00.0: MEM window: 0xd4000000-0xd7ffffff
    pci 0000:02:00.1: CardBus bridge, secondary bus 0000:07
    pci 0000:02:00.1: IO window: 0x004800-0x0048ff
    pci 0000:02:00.1: IO window: 0x004c00-0x004cff
    pci 0000:02:00.1: PREFETCH window: 0xf4000000-0xf7ffffff
    pci 0000:02:00.1: MEM window: 0xd8000000-0xdbffffff
    pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
    pci 0000:00:1e.0: IO window: 0x4000-0x8fff
    pci 0000:00:1e.0: MEM window: 0xd0200000-0xdfffffff
    pci 0000:00:1e.0: PREFETCH window: 0xf0000000-0xf7ffffff
    pci 0000:00:1e.0: setting latency timer to 64
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
    PCI: setting IRQ 11 as level-triggered
    pci 0000:02:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
    pci 0000:02:00.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
    pci_bus 0000:00: resource 0 io: [0x00-0xffff]
    pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
    pci_bus 0000:01: resource 0 io: [0x3000-0x3fff]
    pci_bus 0000:01: resource 1 mem: [0xd0100000-0xd01fffff]
    pci_bus 0000:01: resource 2 pref mem [0xe8000000-0xefffffff]
    pci_bus 0000:02: resource 0 io: [0x4000-0x8fff]
    pci_bus 0000:02: resource 1 mem: [0xd0200000-0xdfffffff]
    pci_bus 0000:02: resource 2 pref mem [0xf0000000-0xf7ffffff]
    pci_bus 0000:02: resource 3 io: [0x00-0xffff]
    pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
    pci_bus 0000:03: resource 0 io: [0x4000-0x40ff]
    pci_bus 0000:03: resource 1 io: [0x4400-0x44ff]
    pci_bus 0000:03: resource 2 pref mem [0xf0000000-0xf3ffffff]
    pci_bus 0000:03: resource 3 mem: [0xd4000000-0xd7ffffff]
    pci_bus 0000:07: resource 0 io: [0x4800-0x48ff]
    pci_bus 0000:07: resource 1 io: [0x4c00-0x4cff]
    pci_bus 0000:07: resource 2 pref mem [0xf4000000-0xf7ffffff]
    pci_bus 0000:07: resource 3 mem: [0xd8000000-0xdbffffff]
    NET: Registered protocol family 2
    IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
    TCP: Hash tables configured (established 131072 bind 65536)
    TCP reno registered
    NET: Registered protocol family 1
    Unpacking initramfs...
    Freeing initrd memory: 738k freed
    Simple Boot Flag at 0x35 set to 0x1
    IBM machine detected. Enabling interrupts during APM calls.
    apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    apm: overridden by ACPI.
    Scanning for low memory corruption every 60 seconds
    audit: initializing netlink socket (disabled)
    type=2000 audit(1259350175.183:1): initialized
    highmem bounce pool size: 64 pages
    VFS: Disk quotas dquot_6.5.2
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    msgmni has been set to 1746
    alg: No test for stdrng (krng)
    Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    pci 0000:01:00.0: Boot video device
    pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
    vesafb: framebuffer at 0xe8000000, mapped to 0xf8080000, using 4608k, total 16320k
    vesafb: mode is 1024x768x24, linelength=3072, pages=6
    vesafb: protected mode interface info at c000:5701
    vesafb: pmi: set display start = c00c5795, set palette = c00c57e1
    vesafb: pmi: ports = 3010 3016 3054 3038 303c 305c 3000 3004 30b0 30b2 30b4
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
    Console: switching to colour frame buffer device 128x48
    fb0: VESA VGA frame buffer device
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
    serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
    00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
    serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
    serial 0000:00:1f.6: PCI INT B disabled
    input: Macintosh mouse button emulation as /devices/virtual/input/input0
    PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    cpuidle: using governor ladder
    cpuidle: using governor menu
    TCP cubic registered
    NET: Registered protocol family 17
    Using IPI No-Shortcut mode
    Switched to high resolution mode on CPU 0
    registered taskstats version 1
    Initalizing network drop monitor service
    Freeing unused kernel memory: 416k freed
    input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
    Floppy drive(s): fd0 is 1.44M
    SCSI subsystem initialized
    FDC 0 is a National Semiconductor PC87306
    libata version 3.00 loaded.
    ata_piix 0000:00:1f.1: version 2.13
    ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
    ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
    ata_piix 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    ata_piix 0000:00:1f.1: setting latency timer to 64
    scsi0 : ata_piix
    scsi1 : ata_piix
    ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1860 irq 14
    ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1868 irq 15
    ata1.00: ATA-7: SAMSUNG MP0201H, YP200-06, max UDMA/100
    ata2.00: ATAPI: HL-DT-STCD-RW/DVD DRIVE GCC-4240N, 0211, max UDMA/33
    ata1.00: 39179952 sectors, multi 16: LBA48
    ata1.00: configured for UDMA/100
    ata2.00: configured for UDMA/33
    scsi 0:0:0:0: Direct-Access ATA SAMSUNG MP0201H YP20 PQ: 0 ANSI: 5
    scsi 1:0:0:0: CD-ROM HL-DT-ST RW/DVD GCC-4240N 0211 PQ: 0 ANSI: 5
    sd 0:0:0:0: [sda] 39179952 512-byte logical blocks: (20.0 GB/18.6 GiB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda: sda1 sda2 sda3 sda4
    sd 0:0:0:0: [sda] Attached SCSI disk
    sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 1:0:0:0: Attached scsi CD-ROM sr0
    EXT4-fs (sda3): INFO: recovery required on readonly filesystem
    EXT4-fs (sda3): write access will be enabled during recovery
    EXT4-fs (sda3): barriers enabled
    kjournald2 starting: pid 500, dev sda3:8, commit interval 5 seconds
    EXT4-fs (sda3): delayed allocation enabled
    EXT4-fs: file extents enabled
    EXT4-fs: mballoc enabled
    EXT4-fs (sda3): orphan cleanup on readonly fs
    EXT4-fs (sda3): ext4_orphan_cleanup: deleting unreferenced inode 212034
    EXT4-fs (sda3): 1 orphan inode deleted
    EXT4-fs (sda3): recovery complete
    EXT4-fs (sda3): mounted filesystem with ordered data mode
    rtc_cmos 00:06: RTC can wake from S4
    rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one month, y3k, 114 bytes nvram
    udev: starting version 146
    intel_rng: FWH not detected
    Linux agpgart interface v0.103
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    sr 1:0:0:0: Attached scsi generic sg1 type 5
    i801_smbus 0000:00:1f.3: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
    input: PC Speaker as /devices/platform/pcspkr/input/input2
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    agpgart-intel 0000:00:00.0: Intel 845G Chipset
    agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xe0000000
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    cfg80211: Using static regulatory domain info
    cfg80211: Regulatory domain: US
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
    (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
    cfg80211: Calling CRDA for country: US
    lp: driver loaded but no devices found
    input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    ACPI: Power Button [PWRF]
    input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input4
    uhci_hcd: USB Universal Host Controller Interface driver
    uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
    uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
    uhci_hcd 0000:00:1d.0: setting latency timer to 64
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
    uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
    uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
    uhci_hcd 0000:00:1d.1: setting latency timer to 64
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    uhci_hcd 0000:00:1d.2: setting latency timer to 64
    uhci_hcd 0000:00:1d.2: UHCI Host Controller
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    thermal LNXTHERM:01: registered as thermal_zone0
    ACPI: Thermal Zone [THM0] (58 C)
    ACPI: Lid Switch [LID]
    input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
    ACPI: Sleep Button [SLPB]
    NET: Registered protocol family 23
    usb 2-2: new full speed USB device using uhci_hcd and address 2
    iTCO_vendor_support: vendor-support=0
    iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
    iTCO_wdt: Found a ICH3-M TCO device (Version=1, TCOBASE=0x1060)
    iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    Marking TSC unstable due to TSC halts in idle
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    processor LNXCPU:00: registered as cooling_device0
    ACPI: Processor [CPU0] (supports 8 throttling states)
    ACPI: AC Adapter [AC] (on-line)
    parport_pc 00:0b: reported by Plug and Play ACPI
    parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
    usb 2-2: configuration #1 chosen from 4 choices
    lp0: using parport0 (interrupt-driven).
    nsc-ircc, chip->init
    nsc-ircc, Found chip at base=0x02e
    nsc-ircc, driver loaded (Dag Brattli)
    nsc_ircc_open(), can't get iobase of 0x2f8
    nsc-ircc, Found chip at base=0x02e
    nsc-ircc, driver loaded (Dag Brattli)
    nsc_ircc_open(), can't get iobase of 0x2f8
    nsc-ircc 00:0c: disabled
    input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:03/device:04/input/input6
    ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
    Non-volatile memory driver v1.3
    thinkpad_acpi: ThinkPad ACPI Extras v0.23
    thinkpad_acpi: http://ibm-acpi.sf.net/
    thinkpad_acpi: ThinkPad BIOS 1IET69WW (2.08 ), EC 1IHT20WW-1.07
    ACPI: Battery Slot [BAT0] (battery present)
    Registered led device: tpacpi::thinklight
    Registered led device: tpacpi::power
    Registered led device: tpacpi::standby
    input: ThinkPad Extra Buttons as /devices/virtual/input/input7
    ppdev: user-space parallel port driver
    yenta_cardbus 0000:02:00.0: CardBus bridge found [1014:0512]
    yenta_cardbus 0000:02:00.0: Using INTVAL to route CSC interrupts to PCI
    yenta_cardbus 0000:02:00.0: Routing CardBus interrupts to PCI
    yenta_cardbus 0000:02:00.0: TI: mfunc 0x01d21022, devctl 0x64
    e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
    e100: Copyright(c) 1999-2006 Intel Corporation
    Synaptics Touchpad, model: 1, fw: 5.9, id: 0x2c6ab1, caps: 0x884793/0x0
    serio: Synaptics pass-through port at isa0060/serio1/input0
    input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
    yenta_cardbus 0000:02:00.0: ISA IRQ mask 0x0438, PCI irq 11
    yenta_cardbus 0000:02:00.0: Socket status: 30000006
    yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0x4000-0x8fff: clean.
    yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xdfffffff
    yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge Memory window: 0xf0000000 - 0xf7ffffff
    [drm] Initialized drm 1.1.0 20060810
    [drm] VGACON disable radeon kernel modesetting.
    pci 0000:01:00.0: power state changed by ACPI to D0
    pci 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
    [drm] Initialized radeon 1.31.0 20080528 for 0000:01:00.0 on minor 0
    ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
    e100 0000:02:08.0: PCI INT A -> Link[LNKE] -> GSI 11 (level, low) -> IRQ 11
    e100 0000:02:08.0: PME# disabled
    e100: eth0: e100_probe: addr 0xd0202000, irq 11, MAC addr 00:0d:60:37:df:cb
    b43-pci-bridge 0000:02:02.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0
    yenta_cardbus 0000:02:00.1: CardBus bridge found [1014:0512]
    yenta_cardbus 0000:02:00.1: Using INTVAL to route CSC interrupts to PCI
    yenta_cardbus 0000:02:00.1: Routing CardBus interrupts to PCI
    yenta_cardbus 0000:02:00.1: TI: mfunc 0x01d21022, devctl 0x64
    b43-phy0: Broadcom 4318 WLAN found (core revision 9)
    phy0: Selected rate control algorithm 'minstrel'
    Broadcom 43xx driver loaded [ Features: PML, Firmware-ID: FW13 ]
    yenta_cardbus 0000:02:00.1: ISA IRQ mask 0x0438, PCI irq 11
    yenta_cardbus 0000:02:00.1: Socket status: 30000006
    yenta_cardbus 0000:02:00.1: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff
    pcmcia_socket pcmcia_socket1: cs: IO port probe 0x4000-0x8fff: clean.
    yenta_cardbus 0000:02:00.1: pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xdfffffff
    yenta_cardbus 0000:02:00.1: pcmcia: parent PCI bridge Memory window: 0xf0000000 - 0xf7ffffff
    fuse init (API version 7.12)
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
    pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af: clean.
    pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff: clean.
    pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7: clean.
    pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
    psmouse serio2: ID: 10 00 64
    EXT4-fs (sda3): internal journal on sda3:8
    EXT4-fs (sda4): barriers enabled
    kjournald2 starting: pid 2051, dev sda4:8, commit interval 5 seconds
    EXT4-fs (sda4): internal journal on sda4:8
    EXT4-fs (sda4): delayed allocation enabled
    EXT4-fs: file extents enabled
    EXT4-fs: mballoc enabled
    EXT4-fs (sda4): mounted filesystem with ordered data mode
    Adding 265064k swap on /dev/sda2. Priority:-1 extents:1 across:265064k
    usb 2-2: USB disconnect, address 2
    IBM TrackPoint firmware: 0x0e, buttons: 3/3
    input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input9
    Clocksource tsc unstable (delta = -78033180 ns)
    oss_ich 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
    usbcore: registered new interface driver oss_usb
    ttyS1: LSR safety check engaged!
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    ADDRCONF(NETDEV_UP): eth0: link is not ready
    agpgart-intel 0000:00:00.0: AGP 2.0 bridge
    agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
    pci 0000:01:00.0: putting AGP V2 device into 4x mode
    [drm] Setting GART location based on new memory map
    [drm] Loading R100 Microcode
    [drm] writeback test succeeded in 1 usecs
    b43 ssb0:0: firmware: requesting b43/ucode5.fw
    b43 ssb0:0: firmware: requesting b43/pcm5.fw
    b43 ssb0:0: firmware: requesting b43/b0g0initvals5.fw
    b43 ssb0:0: firmware: requesting b43/b0g0bsinitvals5.fw
    b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
    Registered led device: b43-phy0::tx
    Registered led device: b43-phy0::rx
    Registered led device: b43-phy0::radio
    ADDRCONF(NETDEV_UP): wlan0: link is not ready
    wlan0: authenticate with AP 00:1e:e5:79:4e:41
    wlan0: authenticated
    wlan0: associate with AP 00:1e:e5:79:4e:41
    wlan0: RX AssocResp from 00:1e:e5:79:4e:41 (capab=0x11 status=0 aid=1)
    wlan0: associated
    ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    wlan0: no IPv6 routers present
    usb 2-2: new full speed USB device using uhci_hcd and address 3
    usb 2-2: configuration #1 chosen from 4 choices
    Consoledump from an openGL game:
    [nick@myhost nick]# tremulous
    tremulous 1.1.0 linux-x86 Mar 17 2009
    ----- FS_Startup -----
    Current search path:
    /root/.tremulous/base
    /opt/tremulous/base/vms-1.1.0.pk3 (4 files)
    /opt/tremulous/base/map-uncreation-1.1.0.pk3 (110 files)
    /opt/tremulous/base/map-tremor-1.1.0.pk3 (45 files)
    /opt/tremulous/base/map-transit-1.1.0.pk3 (135 files)
    /opt/tremulous/base/map-niveus-1.1.0.pk3 (134 files)
    /opt/tremulous/base/map-nexus6-1.1.0.pk3 (151 files)
    /opt/tremulous/base/map-karith-1.1.0.pk3 (118 files)
    /opt/tremulous/base/map-atcs-1.1.0.pk3 (87 files)
    /opt/tremulous/base/map-arachnid2-1.1.0.pk3 (67 files)
    /opt/tremulous/base/data-1.1.0.pk3 (1229 files)
    /opt/tremulous/base
    2080 files in pk3 files
    execing default.cfg
    couldn't exec autogen.cfg
    couldn't exec autoexec.cfg
    Hunk_Clear: reset the hunk ok
    ----- Client Initialization -----
    ----- Initializing Renderer ----
    ----- Client Initialization Complete -----
    ----- R_Init -----
    ------- Input Initialization -------
    Joystick is not active.
    ...loading libGL.so.1:
    Calling SDL_Init(SDL_INIT_VIDEO)...
    SDL_Init(SDL_INIT_VIDEO) passed.
    Initializing OpenGL display
    ...setting mode 3: 640 480
    Using 8/8/8 Color bits, 24 depth, 8 stencil display.
    GL_RENDERER: Mesa DRI R100 (RV200 4C57) 20090101 AGP 4x x86/MMX/SSE2 TCL
    Initializing OpenGL extensions
    ...GL_S3_s3tc not found
    ...ignoring GL_EXT_texture_env_add
    ...using GL_ARB_multitexture
    ...using GL_EXT_compiled_vertex_array
    GL_VENDOR: Tungsten Graphics, Inc.
    GL_RENDERER: Mesa DRI R100 (RV200 4C57) 20090101 AGP 4x x86/MMX/SSE2 TCL
    GL_VERSION: 1.3 Mesa 7.6
    GL_EXTENSIONS: GL_ARB_draw_buffers GL_ARB_imaging GL_ARB_multisample GL_ARB_multitexture GL_ARB_texture_border_clamp GL_ARB_texture_compression GL_ARB_texture_cube_map GL_ARB_texture_env_add GL_ARB_texture_env_combine GL_ARB_texture_env_crossbar GL_ARB_texture_env_dot3 GL_ARB_texture_mirrored_repeat GL_ARB_texture_rectangle GL_ARB_transpose_matrix GL_ARB_vertex_buffer_object GL_ARB_window_pos GL_EXT_abgr GL_EXT_bgra GL_EXT_blend_color GL_EXT_blend_logic_op GL_EXT_blend_minmax GL_EXT_blend_subtract GL_EXT_compiled_vertex_array GL_EXT_convolution GL_EXT_copy_texture GL_EXT_draw_range_elements GL_EXT_fog_coord GL_EXT_histogram GL_EXT_multi_draw_arrays GL_EXT_packed_depth_stencil GL_EXT_packed_pixels GL_EXT_polygon_offset GL_EXT_rescale_normal GL_EXT_secondary_color GL_EXT_separate_specular_color GL_EXT_stencil_wrap GL_EXT_subtexture GL_EXT_texture GL_EXT_texture3D GL_EXT_texture_edge_clamp GL_EXT_texture_env_add GL_EXT_texture_env_combine GL_EXT_texture_env_dot3 GL_EXT_texture_filter_anisotropic GL_EXT_texture_lod_bias GL_EXT_texture_mirror_clamp GL_EXT_texture_object GL_EXT_texture_rectangle GL_EXT_vertex_array GL_APPLE_packed_pixels GL_ATI_texture_env_combine3 GL_ATI_texture_mirror_once GL_IBM_multimode_draw_arrays GL_IBM_rasterpos_clip GL_IBM_texture_mirrored_repeat GL_MESA_ycbcr_texture GL_MESA_window_pos GL_NV_blend_square GL_NV_light_max_exponent GL_NV_texture_rectangle GL_NV_texgen_reflection GL_OES_read_format GL_SGI_color_matrix GL_SGI_color_table GL_SGIS_generate_mipmap GL_SGIS_texture_border_clamp GL_SGIS_texture_edge_clamp GL_SGIS_texture_lod GL_SUN_multi_draw_arrays
    GL_MAX_TEXTURE_SIZE: 2048
    GL_MAX_ACTIVE_TEXTURES_ARB: 3
    PIXELFORMAT: color(24-bits) Z(24-bit) stencil(8-bits)
    MODE: 3, 640 x 480 fullscreen hz:N/A
    GAMMA: hardware w/ 0 overbright bits
    CPU:
    rendering primitives: single glDrawElements
    texturemode: GL_LINEAR_MIPMAP_LINEAR
    picmip: 0
    texture bits: 0
    multitexture: enabled
    compiled vertex arrays: enabled
    texenv add: disabled
    compressed textures: disabled
    Initializing Shaders
    ...loading 'scripts/uncreation.shader'
    ...loading 'scripts/q3map2_tremor.shader'
    ...loading 'scripts/tremor.shader'
    ...loading 'scripts/transit.shader'
    ...loading 'scripts/niveus.shader'
    ...loading 'scripts/nexus6.shader'
    ...loading 'scripts/karith.shader'
    ...loading 'scripts/atcs.shader'
    ...loading 'scripts/arachnid2.shader'
    ...loading 'scripts/jetpack.shader'
    ...loading 'scripts/core.shader'
    ...loading 'scripts/flame.shader'
    ...loading 'scripts/misc.shader'
    ...loading 'scripts/common-trem.shader'
    ...loading 'scripts/titan.shader'
    ...loading 'scripts/water.shader'
    ...loading 'scripts/displays.shader'
    ...loading 'scripts/plant_life.shader'
    ...loading 'scripts/stasis.shader'
    ...loading 'scripts/booster.shader'
    ...loading 'scripts/eggpod.shader'
    ...loading 'scripts/medistat.shader'
    ...loading 'scripts/mgturret.shader'
    ...loading 'scripts/reactor.shader'
    ...loading 'scripts/telenode.shader'
    ...loading 'scripts/trapper.shader'
    ...loading 'scripts/overmind.shader'
    ...loading 'scripts/tesla.shader'
    ...loading 'scripts/dcc.shader'
    ...loading 'scripts/hive.shader'
    ...loading 'scripts/level2.shader'
    ...loading 'scripts/human.shader'
    ...loading 'scripts/null.shader'
    ...loading 'scripts/weapons.shader'
    ...loading 'scripts/conkit.shader'
    ...loading 'scripts/advckit.shader'
    ...loading 'scripts/psaw.shader'
    ...loading 'scripts/mdriver.shader'
    ...loading 'scripts/flamer.shader'
    ...loading 'scripts/crosshairs.shader'
    ...loading 'scripts/grenade.shader'
    ...loading 'scripts/splash.shader'
    ...loading 'scripts/marks.shader'
    ...loading 'scripts/sprites.shader'
    ...loading 'scripts/muzzleflashes.shader'
    ----- finished R_Init -----
    ------ Initializing Sound ------
    Initializing SDL audio driver...
    ALSA lib confmisc.c:768:(parse_card) cannot find card '0'
    ALSA lib conf.c:4154:(_snd_config_evaluate) function snd_func_card_driver returned error: No such file or directory
    ALSA lib confmisc.c:392:(snd_func_concat) error evaluating strings
    ALSA lib conf.c:4154:(_snd_config_evaluate) function snd_func_concat returned error: No such file or directory
    ALSA lib confmisc.c:1251:(snd_func_refer) error evaluating name
    ALSA lib conf.c:4154:(_snd_config_evaluate) function snd_func_refer returned error: No such file or directory
    ALSA lib conf.c:4633:(snd_config_expand) Evaluate error: No such file or directory
    ALSA lib pcm.c:2211:(snd_pcm_open_noupdate) Unknown PCM default
    SDL audio driver is "dsp".
    SDL_AudioSpec:
    Format: AUDIO_S16LSB
    Freq: 22050
    Samples: 512
    Channels: 2
    Starting SDL audio callback...
    SDL audio initialized.
    ----- Sound Info -----
    1 stereo
    16384 samples
    16 samplebits
    1 submission_chunk
    22050 speed
    0xa4241f8 dma buffer
    No background file.
    Sound intialization successful.
    Sound memory manager started
    Loading vm file vm/ui.qvm...
    ...which has vmMagic VM_MAGIC_VER2
    Loading 1075 jump table targets
    VM file ui compiled to 786313 bytes of code
    ui loaded in 4596672 bytes on the hunk
    UI menu load time = 705 milli seconds
    UI menu load time = 55 milli seconds
    UI menu load time = 51 milli seconds
    --- Common Initialization Complete ---
    Opening IP socket: localhost:30720
    Hostname: myhost.localdomain
    Alias: myhost
    IP: 127.0.0.1
    Started tty console (use +set ttycon 0 to disable)
    *********************************WARN_ONCE*********************************
    File radeon_tcl.c function radeon_run_tcl_render line 499
    Rendering was 734 commands larger than predicted size. We might overflow command buffer.
    ----- CL_Shutdown -----
    Closing SDL audio device...
    SDL audio device shut down.
    RE_Shutdown( 1 )
    ----- CL_Shutdown -----
    Shutdown tty console
    [nick@myhost nick]#
    Display all 3035 possibilities? (y or n)

    radionecrotic wrote:
    Has this always been the case for you or did you update recently and it started happening?  There appears to be some sort of conflict with some machines and new changes to the kernel to allow quicker mode setting.  See http://bbs.archlinux.org/viewtopic.php? … 47#p659347.  I had to add !radeon to my MODULES list in /etc/rc.conf to get X to even work at all.  I don't run anything that uses OpenGL so I don't know if it'll address your issue.
    You may also want to take a look at http://bbs.archlinux.org/viewtopic.php? … 20#p662920 and add intel_agp radeon (that's two modules, in that order) to your MODULES list.
    Well, I was having the graphical corruption issue in that first thread until I added the nomodeset boot flag. As for the modesetting, I think it directly conflicts with my boot flag, and without it, I get corruption. =/

  • Display resolution on ATI Radeon 7500

    Just bought a LG 22" which runs 1650x1050 native resolution (WSXGA+) and although the dropdown box in XP says I'm there I'm really not. The fonts are obviously wider than they should be,images that are 1650x1050 require scrolling, etc.
    Any idea what can be done to get this video card to do what it says? Is this a windows problem?
    any help is appreciated. thx

    Hey, thanks. Took me all night to find that documented on the ATI (AMD) website.
    I found a driver that works great and supports the resolution I needed.... pass it on.
     http://www.omegadrivers.net/ati_winxp.php
    thanks,
    - Drew
    Message Edited by Drew on 03-22-2008 06:43 PM
    Moderator Note: converted to clickable link
    Message Edited by andyP on 03-24-2008 10:58 PM

  • [Solved] xf86-video-ati driver and [Radeon Mobility 7500] help

    I have an thinkpad T42 laptop (video card is ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500]) with openbox and slim and I instaled xf86-video-ati. My problem is that minimizing and maximizing are very slow, lxterminal decoration bar disapear..... I also tried to install xf86-video-ati-git without any improuvements.
    this is my xorg.conf:
    Section "ServerLayout"
    Identifier "Default Layout"
    Screen 0 "Screen0" 0 0
    InputDevice "Mouse0" "CorePointer"
    InputDevice "SynapticsTouchpad" "SendCoreEvents"
    InputDevice "Keyboard0" "CoreKeyboard"
    Option "AIGLX" "true
    EndSection
    Section "ServerFlags"
    Option "AutoAddDevices" "False"
    EndSection
    Section "Files"
    ModulePath "/usr/lib/xorg/modules"
    FontPath "/usr/share/fonts/misc:unscaled"
    FontPath "/usr/share/fonts/misc"
    FontPath "/usr/share/fonts/75dpi:unscaled"
    FontPath "/usr/share/fonts/75dpi"
    FontPath "/usr/share/fonts/100dpi:unscaled"
    FontPath "/usr/share/fonts/100dpi"
    # FontPath "/usr/share/fonts/PEX"
    # Additional fonts: Locale, Gimp, TTF...
    # FontPath "/usr/share/fonts/cyrillic"
    # FontPath "/usr/share/lib/X11/fonts/latin2/75dpi"
    # FontPath "/usr/share/lib/X11/fonts/latin2/100dpi"
    # True type and type1 fonts are also handled via xftlib, see /etc/X11/XftConfig!
    FontPath "/usr/share/fonts/Type1"
    # FontPath "/usr/share/fonts/ttf/western"
    # FontPath "/usr/share/fonts/ttf/decoratives"
    # FontPath "/usr/share/fonts/truetype"
    # FontPath "/usr/share/fonts/truetype/openoffice"
    # FontPath "/usr/share/fonts/truetype/ttf-bitstream-vera"
    # FontPath "/usr/share/fonts/latex-ttf-fonts"
    # FontPath "/usr/share/fonts/defoma/CID"
    # FontPath "/usr/share/fonts/defoma/TrueType"
    EndSection
    Section "Module"
    Load "ddc" # ddc probing of monitor
    Load "bitmap" # bitmap-fonts
    Load "type1"
    Load "freetype"
    Load "record"
    Load "dbe"
    Load "glx"
    Load "dri2"
    Load "dri"
    Load "synaptics"
    Load "extmod"
    EndSection
    Section "InputDevice"
    Identifier "Keyboard0"
    Driver "kbd"
    EndSection
    Section "InputDevice"
    Identifier "Mouse0"
    Driver "mouse"
    Option "CorePointer"
    Option "Protocol" "ExplorerPS/2"
    Option "Device" "/dev/input/mice"
    Option "Emulate3Buttons" "on"
    Option "YAxisMapping" "4 5"
    Option "XAxisMapping" "6 7"
    Option "ZAxisMapping" "4 5"
    EndSection
    Section "InputDevice"
    Identifier "SynapticsTouchpad"
    Driver "synaptics"
    Option "AlwaysCore" "true" # send events to CorePointer
    Option "VertEdgeScroll" "true" # enable vertical scroll zone
    EndSection
    Section "Monitor"
    Identifier "Monitor0"
    Option "DPMS" "true"
    # HorizSync 28.0 - 78.0 # Warning: This may fry very old Monitors
    HorizSync 28.0 - 96.0 # Warning: This may fry old Monitors
    VertRefresh 50.0 - 75.0 # Very conservative. May flicker.
    # VertRefresh 50.0 - 62.0 # Extreme conservative. Will flicker. TFT default.
    # Default modes distilled from
    # "VESA and Industry Standards and Guide for Computer Display Monitor
    # Timing", version 1.0, revision 0.8, adopted September 17, 1998.
    # $XFree86: xc/programs/Xserver/hw/xfree86/etc/vesamodes,v 1.4 1999/11/18 16:52:17 tsi Exp $
    # 640x350 @ 85Hz (VESA) hsync: 37.9kHz
    ModeLine "640x350" 31.5 640 672 736 832 350 382 385 445 +hsync -vsync
    # 640x400 @ 85Hz (VESA) hsync: 37.9kHz
    ModeLine "640x400" 31.5 640 672 736 832 400 401 404 445 -hsync +vsync
    # 720x400 @ 85Hz (VESA) hsync: 37.9kHz
    ModeLine "720x400" 35.5 720 756 828 936 400 401 404 446 -hsync +vsync
    # 640x480 @ 60Hz (Industry standard) hsync: 31.5kHz
    ModeLine "640x480" 25.2 640 656 752 800 480 490 492 525 -hsync -vsync
    # 640x480 @ 72Hz (VESA) hsync: 37.9kHz
    ModeLine "640x480" 31.5 640 664 704 832 480 489 491 520 -hsync -vsync
    # 640x480 @ 75Hz (VESA) hsync: 37.5kHz
    ModeLine "640x480" 31.5 640 656 720 840 480 481 484 500 -hsync -vsync
    # 640x480 @ 85Hz (VESA) hsync: 43.3kHz
    ModeLine "640x480" 36.0 640 696 752 832 480 481 484 509 -hsync -vsync
    # 800x600 @ 56Hz (VESA) hsync: 35.2kHz
    ModeLine "800x600" 36.0 800 824 896 1024 600 601 603 625 +hsync +vsync
    # 800x600 @ 60Hz (VESA) hsync: 37.9kHz
    ModeLine "800x600" 40.0 800 840 968 1056 600 601 605 628 +hsync +vsync
    # 800x600 @ 72Hz (VESA) hsync: 48.1kHz
    ModeLine "800x600" 50.0 800 856 976 1040 600 637 643 666 +hsync +vsync
    # 800x600 @ 75Hz (VESA) hsync: 46.9kHz
    ModeLine "800x600" 49.5 800 816 896 1056 600 601 604 625 +hsync +vsync
    # 800x600 @ 85Hz (VESA) hsync: 53.7kHz
    ModeLine "800x600" 56.3 800 832 896 1048 600 601 604 631 +hsync +vsync
    # 1024x768i @ 43Hz (industry standard) hsync: 35.5kHz
    ModeLine "1024x768" 44.9 1024 1032 1208 1264 768 768 776 817 +hsync +vsync Interlace
    # 1024x768 @ 60Hz (VESA) hsync: 48.4kHz
    ModeLine "1024x768" 65.0 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
    # 1024x768 @ 70Hz (VESA) hsync: 56.5kHz
    ModeLine "1024x768" 75.0 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
    # 1024x768 @ 75Hz (VESA) hsync: 60.0kHz
    ModeLine "1024x768" 78.8 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
    # 1024x768 @ 85Hz (VESA) hsync: 68.7kHz
    ModeLine "1024x768" 94.5 1024 1072 1168 1376 768 769 772 808 +hsync +vsync
    # Extended modelines with GTF timings
    # 640x480 @ 100.00 Hz (GTF) hsync: 50.90 kHz; pclk: 43.16 MHz
    ModeLine "640x480" 43.16 640 680 744 848 480 481 484 509 -HSync +Vsync
    # 768x576 @ 60.00 Hz (GTF) hsync: 35.82 kHz; pclk: 34.96 MHz
    ModeLine "768x576" 34.96 768 792 872 976 576 577 580 597 -HSync +Vsync
    # 768x576 @ 72.00 Hz (GTF) hsync: 43.27 kHz; pclk: 42.93 MHz
    ModeLine "768x576" 42.93 768 800 880 992 576 577 580 601 -HSync +Vsync
    # 768x576 @ 75.00 Hz (GTF) hsync: 45.15 kHz; pclk: 45.51 MHz
    ModeLine "768x576" 45.51 768 808 888 1008 576 577 580 602 -HSync +Vsync
    # 768x576 @ 85.00 Hz (GTF) hsync: 51.42 kHz; pclk: 51.84 MHz
    ModeLine "768x576" 51.84 768 808 888 1008 576 577 580 605 -HSync +Vsync
    # 768x576 @ 100.00 Hz (GTF) hsync: 61.10 kHz; pclk: 62.57 MHz
    ModeLine "768x576" 62.57 768 816 896 1024 576 577 580 611 -HSync +Vsync
    # 800x600 @ 100.00 Hz (GTF) hsync: 63.60 kHz; pclk: 68.18 MHz
    ModeLine "800x600" 68.18 800 848 936 1072 600 601 604 636 -HSync +Vsync
    # 1024x768 @ 100.00 Hz (GTF) hsync: 81.40 kHz; pclk: 113.31 MHz
    ModeLine "1024x768" 113.31 1024 1096 1208 1392 768 769 772 814 -HSync +Vsync
    EndSection
    Section "Device"
    Identifier "Card0"
    Boardname "ATI Radeon"
    Busid "PCI:1:0:0"
    Driver "radeon"
    Screen 0
    Vendorname "ATI"
    Option "MergedFB" "off"
    Option "AccelMethod" "EXA"
    Option "EXANoComposite" "false"
    Option "FBTexPercent" "50"
    Option "MigrationHeuristic" "greedy"
    Option "DRI" "true"
    Option "GARTSize" "1536"
    Option "AGPMode" "4"
    Option "Colortiling" "On"
    EndSection
    Section "Screen"
    Identifier "Screen0"
    Device "Card0"
    Monitor "Monitor0"
    DefaultColorDepth 24
    SubSection "Display"
    Depth 1
    Modes "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
    Depth 4
    Modes "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
    Depth 8
    Modes "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
    Depth 15
    Modes "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
    Depth 16
    Modes "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
    Depth 24
    Modes "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
    Depth 32
    Modes "1024x768" "800x600" "640x480"
    EndSubSection
    EndSection
    Section "DRI"
    Mode 0666
    EndSection
    Section "Extensions"
    Option "Composite" "Enable"
    EndSection
    Last edited by botzoboy (2010-05-29 07:39:30)

    theapodan
    this is my Xorg.0.log:
    X.Org X Server 1.7.6
    Release Date: 2010-03-17
    X Protocol Version 11, Revision 0
    Build Operating System: Linux 2.6.33-ARCH i686
    Current Operating System: Linux arch 2.6.33-ARCH #1 SMP PREEMPT Thu May 13 12:06:25 CEST 2010 i686
    Kernel command line: root=/dev/disk/by-uuid/7e750225-da5a-470f-a024-af37495f11d5 ro
    Build Date: 01 April 2010 05:35:33PM
    Current version of pixman: 0.18.2
    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
    Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
    (==) Log file: "/var/log/Xorg.0.log", Time: Sat May 29 09:20:42 2010
    (==) Using config file: "/etc/X11/xorg.conf"
    (==) ServerLayout "Default Layout"
    (**) |-->Screen "Screen0" (0)
    (**) | |-->Monitor "Monitor0"
    (**) | |-->Device "Card0"
    (**) |-->Input Device "Mouse0"
    (**) |-->Input Device "SynapticsTouchpad"
    (**) |-->Input Device "Keyboard0"
    (**) Option "AIGLX" "true"
    (**) Option "AutoAddDevices" "False"
    (**) Not automatically adding devices
    (==) Automatically enabling devices
    (**) FontPath set to:
    /usr/share/fonts/misc:unscaled,
    /usr/share/fonts/misc,
    /usr/share/fonts/75dpi:unscaled,
    /usr/share/fonts/75dpi,
    /usr/share/fonts/100dpi:unscaled,
    /usr/share/fonts/100dpi,
    /usr/share/fonts/Type1,
    /usr/share/fonts/misc,
    /usr/share/fonts/100dpi:unscaled,
    /usr/share/fonts/75dpi:unscaled,
    /usr/share/fonts/TTF,
    /usr/share/fonts/Type1
    (**) ModulePath set to "/usr/lib/xorg/modules"
    (**) Extension "Composite" is enabled
    (II) Loader magic: 0x81e4c60
    (II) Module ABI versions:
    X.Org ANSI C Emulation: 0.4
    X.Org Video Driver: 6.0
    X.Org XInput driver : 7.0
    X.Org Server Extension : 2.0
    (++) using VT number 7
    (--) PCI:*(0:1:0:0) 1002:4c57:1014:0530 ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] rev 0, Mem @ 0xe0000000/134217728, 0xc0100000/65536, I/O @ 0x00003000/256, BIOS @ 0x????????/131072
    (II) Open ACPI successful (/var/run/acpid.socket)
    (II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
    (II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
    (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
    (II) "record" will be loaded. This was enabled by default and also specified in the config file.
    (II) "dri" will be loaded. This was enabled by default and also specified in the config file.
    (II) "dri2" will be loaded. This was enabled by default and also specified in the config file.
    (II) LoadModule: "ddc"
    (II) Module "ddc" already built-in
    (II) LoadModule: "record"
    (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
    (II) Module record: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.13.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
    (II) Loading extension RECORD
    (II) LoadModule: "dbe"
    (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
    (II) Module dbe: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
    (II) Loading extension DOUBLE-BUFFER
    (II) LoadModule: "glx"
    (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
    (II) Module glx: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.0.0
    ABI class: X.Org Server Extension, version 2.0
    (**) AIGLX enabled
    (II) Loading extension GLX
    (II) LoadModule: "dri2"
    (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
    (II) Module dri2: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.1.0
    ABI class: X.Org Server Extension, version 2.0
    (II) Loading extension DRI2
    (II) LoadModule: "dri"
    (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
    (II) Module dri: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.0.0
    ABI class: X.Org Server Extension, version 2.0
    (II) Loading extension XFree86-DRI
    (II) LoadModule: "synaptics"
    (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
    (II) Module synaptics: vendor="X.Org Foundation"
    compiled for 1.7.3, module version = 1.2.1
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 7.0
    (II) LoadModule: "extmod"
    (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
    (II) Module extmod: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
    (II) Loading extension MIT-SCREEN-SAVER
    (II) Loading extension XFree86-VidModeExtension
    (II) Loading extension XFree86-DGA
    (II) Loading extension DPMS
    (II) Loading extension XVideo
    (II) Loading extension XVideo-MotionCompensation
    (II) Loading extension X-Resource
    (II) LoadModule: "radeon"
    (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
    (II) Module radeon: vendor="X.Org Foundation"
    compiled for 1.7.5.902, module version = 6.12.192
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 6.0
    (II) LoadModule: "mouse"
    (II) Loading /usr/lib/xorg/modules/input/mouse_drv.so
    (II) Module mouse: vendor="X.Org Foundation"
    compiled for 1.7.0.901, module version = 1.5.0
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 7.0
    (II) LoadModule: "synaptics"
    (II) Reloading /usr/lib/xorg/modules/input/synaptics_drv.so
    (II) LoadModule: "kbd"
    (II) Loading /usr/lib/xorg/modules/input/kbd_drv.so
    (II) Module kbd: vendor="X.Org Foundation"
    compiled for 1.7.0.901, module version = 1.4.0
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 7.0
    (II) RADEON: Driver for ATI Radeon chipsets:
    ATI Radeon Mobility X600 (M24) 3150 (PCIE), ATI FireMV 2400 (PCI),
    ATI Radeon Mobility X300 (M24) 3152 (PCIE),
    ATI FireGL M24 GL 3154 (PCIE), ATI Radeon X600 (RV380) 3E50 (PCIE),
    ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
    ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
    ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
    ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
    ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
    ATI FireGL X2 AK (AGP), ATI Radeon 9600 AP (AGP),
    ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
    ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP), ATI Radeon 9650,
    ATI FireGL RV360 AV (AGP), ATI Radeon 7000 IGP (A4+) 4237,
    ATI Radeon 8500 AIW BB (AGP), ATI Radeon 8500 AIW BC (AGP),
    ATI Radeon IGP320M (U1) 4336, ATI Radeon IGP330M/340M/350M (U2) 4337,
    ATI Radeon Mobility 7000 IGP 4437, ATI Radeon 9000/PRO If (AGP/PCI),
    ATI Radeon 9000 Ig (AGP/PCI), ATI Radeon X800 (R420) JH (AGP),
    ATI Radeon X800PRO (R420) JI (AGP),
    ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
    ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
    ATI Radeon Mobility 9800 (M18) JN (AGP),
    ATI Radeon X800 SE (R420) (AGP), ATI Radeon X800XT (R420) JP (AGP),
    ATI Radeon X800 VE (R420) JT (AGP), ATI Radeon X850 (R480) (AGP),
    ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
    ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP),
    ATI Radeon Mobility M7 LW (AGP),
    ATI Mobility FireGL 7800 M7 LX (AGP),
    ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
    ATI FireGL Mobility 9000 (M9) Ld (AGP),
    ATI Radeon Mobility 9000 (M9) Lf (AGP),
    ATI Radeon Mobility 9000 (M9) Lg (AGP), ATI Radeon 9700 Pro ND (AGP),
    ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9600TX NF (AGP),
    ATI FireGL X1 NG (AGP), ATI Radeon 9800PRO NH (AGP),
    ATI Radeon 9800 NI (AGP), ATI FireGL X2 NK (AGP),
    ATI Radeon 9800XT NJ (AGP),
    ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
    ATI Radeon Mobility 9600 (M10) NQ (AGP),
    ATI Radeon Mobility 9600 (M11) NR (AGP),
    ATI Radeon Mobility 9600 (M10) NS (AGP),
    ATI FireGL Mobility T2 (M10) NT (AGP),
    ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon QD (AGP),
    ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
    ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
    ATI Radeon 9100 QM (AGP), ATI Radeon 7500 QW (AGP/PCI),
    ATI Radeon 7500 QX (AGP/PCI), ATI Radeon VE/7000 QY (AGP/PCI),
    ATI Radeon VE/7000 QZ (AGP/PCI), ATI ES1000 515E (PCI),
    ATI Radeon Mobility X300 (M22) 5460 (PCIE),
    ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
    ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R423) UH (PCIE),
    ATI Radeon X800PRO (R423) UI (PCIE),
    ATI Radeon X800LE (R423) UJ (PCIE),
    ATI Radeon X800SE (R423) UK (PCIE),
    ATI Radeon X800 XTP (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
    ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 (R430) (PCIE),
    ATI FireGL V7100 (R423) (PCIE), ATI FireGL V5100 (R423) UQ (PCIE),
    ATI FireGL unknown (R423) UR (PCIE),
    ATI FireGL unknown (R423) UT (PCIE),
    ATI Mobility FireGL V5000 (M26) (PCIE),
    ATI Mobility FireGL V5000 (M26) (PCIE),
    ATI Mobility Radeon X700 XL (M26) (PCIE),
    ATI Mobility Radeon X700 (M26) (PCIE),
    ATI Mobility Radeon X700 (M26) (PCIE),
    ATI Radeon X550XTX 5657 (PCIE), ATI Radeon 9100 IGP (A5) 5834,
    ATI Radeon Mobility 9100 IGP (U3) 5835,
    ATI Radeon XPRESS 200 5954 (PCIE),
    ATI Radeon XPRESS 200M 5955 (PCIE), ATI Radeon 9250 5960 (AGP),
    ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
    ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
    ATI ES1000 5969 (PCI), ATI Radeon XPRESS 200 5974 (PCIE),
    ATI Radeon XPRESS 200M 5975 (PCIE),
    ATI Radeon XPRESS 200 5A41 (PCIE),
    ATI Radeon XPRESS 200M 5A42 (PCIE),
    ATI Radeon XPRESS 200 5A61 (PCIE),
    ATI Radeon XPRESS 200M 5A62 (PCIE),
    ATI Radeon X300 (RV370) 5B60 (PCIE),
    ATI Radeon X600 (RV370) 5B62 (PCIE),
    ATI Radeon X550 (RV370) 5B63 (PCIE),
    ATI FireGL V3100 (RV370) 5B64 (PCIE),
    ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
    ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
    ATI Radeon Mobility 9200 (M9+) 5C63 (AGP),
    ATI Mobility Radeon X800 XT (M28) (PCIE),
    ATI Mobility FireGL V5100 (M28) (PCIE),
    ATI Mobility Radeon X800 (M28) (PCIE), ATI Radeon X850 5D4C (PCIE),
    ATI Radeon X850 XT PE (R480) (PCIE),
    ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
    ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
    ATI Radeon X850 XT (R480) (PCIE),
    ATI Radeon X800XT (R423) 5D57 (PCIE),
    ATI FireGL V5000 (RV410) (PCIE), ATI Radeon X700 XT (RV410) (PCIE),
    ATI Radeon X700 PRO (RV410) (PCIE),
    ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
    ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X1800,
    ATI Mobility Radeon X1800 XT, ATI Mobility Radeon X1800,
    ATI Mobility FireGL V7200, ATI FireGL V7200, ATI FireGL V5300,
    ATI Mobility FireGL V7100, ATI Radeon X1800, ATI Radeon X1800,
    ATI Radeon X1800, ATI Radeon X1800, ATI Radeon X1800,
    ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
    ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
    ATI Mobility Radeon X1400, ATI Radeon X1300/X1550,
    ATI Radeon X1550 64-bit, ATI Mobility Radeon X1300,
    ATI Mobility Radeon X1300, ATI Mobility Radeon X1300,
    ATI Mobility Radeon X1300, ATI Radeon X1300, ATI Radeon X1300,
    ATI RV505, ATI RV505, ATI FireGL V3300, ATI FireGL V3350,
    ATI Radeon X1300, ATI Radeon X1550 64-bit, ATI Radeon X1300/X1550,
    ATI Radeon X1600, ATI Radeon X1300/X1550, ATI Mobility Radeon X1450,
    ATI Radeon X1300/X1550, ATI Mobility Radeon X2300,
    ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
    ATI Mobility Radeon X1350, ATI Mobility Radeon X1450,
    ATI Radeon X1300, ATI Radeon X1550, ATI Mobility Radeon X1350,
    ATI FireMV 2250, ATI Radeon X1550 64-bit, ATI Radeon X1600,
    ATI Radeon X1650, ATI Radeon X1600, ATI Radeon X1600,
    ATI Mobility FireGL V5200, ATI Mobility Radeon X1600,
    ATI Radeon X1650, ATI Radeon X1650, ATI Radeon X1600,
    ATI Radeon X1300 XT/X1600 Pro, ATI FireGL V3400,
    ATI Mobility FireGL V5250, ATI Mobility Radeon X1700,
    ATI Mobility Radeon X1700 XT, ATI FireGL V5200,
    ATI Mobility Radeon X1700, ATI Radeon X2300HD,
    ATI Mobility Radeon HD 2300, ATI Mobility Radeon HD 2300,
    ATI Radeon X1950, ATI Radeon X1900, ATI Radeon X1950,
    ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
    ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
    ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
    ATI AMD Stream Processor, ATI Radeon X1900, ATI Radeon X1950,
    ATI RV560, ATI RV560, ATI Mobility Radeon X1900, ATI RV560,
    ATI Radeon X1950 GT, ATI RV570, ATI RV570, ATI FireGL V7400,
    ATI RV560, ATI Radeon X1650, ATI Radeon X1650, ATI RV560,
    ATI Radeon 9100 PRO IGP 7834, ATI Radeon Mobility 9200 IGP 7835,
    ATI Radeon X1200, ATI Radeon X1200, ATI Radeon X1200,
    ATI Radeon X1200, ATI Radeon X1200, ATI RS740, ATI RS740M, ATI RS740,
    ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 XT,
    ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro, ATI Radeon HD 2900 GT,
    ATI FireGL V8650, ATI FireGL V8600, ATI FireGL V7600,
    ATI Radeon 4800 Series, ATI Radeon HD 4870 x2,
    ATI Radeon 4800 Series, ATI Radeon HD 4850 x2,
    ATI FirePro V8750 (FireGL), ATI FirePro V7760 (FireGL),
    ATI Mobility RADEON HD 4850, ATI Mobility RADEON HD 4850 X2,
    ATI Radeon 4800 Series, ATI FirePro RV770, AMD FireStream 9270,
    AMD FireStream 9250, ATI FirePro V8700 (FireGL),
    ATI Mobility RADEON HD 4870, ATI Mobility RADEON M98,
    ATI Radeon 4800 Series, ATI Radeon 4800 Series, ATI FirePro M7750,
    ATI M98, ATI M98, ATI M98, ATI Mobility Radeon HD 4650,
    ATI Radeon RV730 (AGP), ATI Mobility Radeon HD 4670,
    ATI FirePro M5750, ATI Radeon RV730 (AGP),
    ATI RV730XT [Radeon HD 4670], ATI RADEON E4600,
    ATI Radeon HD 4600 Series, ATI RV730 PRO [Radeon HD 4650],
    ATI FirePro V7750 (FireGL), ATI FirePro V5700 (FireGL),
    ATI FirePro V3750 (FireGL), ATI Mobility Radeon HD 4830,
    ATI Mobility Radeon HD 4850, ATI FirePro M7740, ATI RV740,
    ATI Radeon HD 4770, ATI Radeon HD 4700 Series, ATI Radeon HD 4770,
    ATI FirePro M5750, ATI RV610, ATI Radeon HD 2400 XT,
    ATI Radeon HD 2400 Pro, ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000,
    ATI RV610, ATI Radeon HD 2350, ATI Mobility Radeon HD 2400 XT,
    ATI Mobility Radeon HD 2400, ATI RADEON E2400, ATI RV610,
    ATI FireMV 2260, ATI RV670, ATI Radeon HD3870,
    ATI Mobility Radeon HD 3850, ATI Radeon HD3850,
    ATI Mobility Radeon HD 3850 X2, ATI RV670,
    ATI Mobility Radeon HD 3870, ATI Mobility Radeon HD 3870 X2,
    ATI Radeon HD3870 X2, ATI FireGL V7700, ATI Radeon HD3850,
    ATI Radeon HD3690, AMD Firestream 9170, ATI Radeon HD 4550,
    ATI Radeon RV710, ATI Radeon RV710, ATI Radeon HD 4350,
    ATI Mobility Radeon 4300 Series, ATI Mobility Radeon 4500 Series,
    ATI Mobility Radeon 4500 Series, ATI FirePro RG220, ATI RV630,
    ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
    ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
    ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
    ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
    ATI FireGL V3600, ATI Radeon HD 2600 LE,
    ATI Mobility FireGL Graphics Processor, ATI Radeon RV710,
    ATI Radeon HD 3470, ATI Mobility Radeon HD 3430,
    ATI Mobility Radeon HD 3400 Series, ATI Radeon HD 3450,
    ATI Radeon HD 3450, ATI Radeon HD 3430, ATI Radeon HD 3450,
    ATI FirePro V3700, ATI FireMV 2450, ATI FireMV 2260, ATI FireMV 2260,
    ATI Radeon HD 3600 Series, ATI Radeon HD 3650 AGP,
    ATI Radeon HD 3600 PRO, ATI Radeon HD 3600 XT,
    ATI Radeon HD 3600 PRO, ATI Mobility Radeon HD 3650,
    ATI Mobility Radeon HD 3670, ATI Mobility FireGL V5700,
    ATI Mobility FireGL V5725, ATI Radeon HD 3200 Graphics,
    ATI Radeon 3100 Graphics, ATI Radeon HD 3200 Graphics,
    ATI Radeon 3100 Graphics, ATI Radeon HD 3300 Graphics,
    ATI Radeon HD 3200 Graphics, ATI Radeon 3000 Graphics,
    ATI Radeon HD 4200, ATI Radeon 4100, ATI Mobility Radeon HD 4200,
    ATI Mobility Radeon 4100, ATI Radeon HD 4290, ATI Radeon HD 4290,
    CYPRESS, ATI FirePro (FireGL) Graphics Adapter,
    ATI FirePro (FireGL) Graphics Adapter,
    ATI FirePro (FireGL) Graphics Adapter, ATI Radeon HD 5800 Series,
    ATI Radeon HD 5800 Series, ATI Radeon HD 5800 Series,
    ATI Radeon HD 5900 Series, ATI Radeon HD 5900 Series,
    ATI Mobility Radeon HD 5800 Series,
    ATI Mobility Radeon HD 5800 Series,
    ATI FirePro (FireGL) Graphics Adapter,
    ATI FirePro (FireGL) Graphics Adapter,
    ATI Mobility Radeon HD 5800 Series, ATI Radeon HD 5700 Series,
    ATI Radeon HD 5700 Series, ATI Radeon HD 5700 Series,
    ATI Mobility Radeon HD 5000 Series,
    ATI Mobility Radeon HD 5000 Series,
    ATI FirePro (FireGL) Graphics Adapter,
    ATI FirePro (FireGL) Graphics Adapter, ATI Radeon HD 5670,
    ATI Radeon HD 5570, ATI Radeon HD 5500 Series, REDWOOD,
    ATI Mobility Radeon HD 5000 Series,
    ATI Mobility Radeon HD 5000 Series, CEDAR, CEDAR, CEDAR,
    ATI FirePro (FireGL) Graphics Adapter,
    ATI FirePro (FireGL) Graphics Adapter, CEDAR, ATI Radeon HD 5450,
    CEDAR
    (II) Primary Device is: PCI 01@00:00:0
    (II) [KMS] Kernel modesetting enabled.
    (**) RADEON(0): Depth 24, (--) framebuffer bpp 32
    (II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
    (==) RADEON(0): Default visual is TrueColor
    (**) RADEON(0): Option "ColorTiling" "On"
    (**) RADEON(0): Option "AccelMethod" "EXA"
    (**) RADEON(0): Option "DRI" "true"
    (==) RADEON(0): RGB weight 888
    (II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
    (--) RADEON(0): Chipset: "ATI Radeon Mobility M7 LW (AGP)" (ChipID = 0x4c57)
    (II) RADEON(0): AGP card detected
    (II) RADEON(0): KMS Color Tiling: enabled
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is 9, (OK)
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is 9, (OK)
    drmOpenByBusid: Searching for BusID pci:0000:01:00.0
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is 9, (OK)
    drmOpenByBusid: drmOpenMinor returns 9
    drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
    (II) [drm] DRM interface version 1.3
    (II) [drm] DRM open master succeeded.
    (II) RADEON(0): Output VGA-0 using monitor section Monitor0
    (II) RADEON(0): Output DVI-0 has no monitor section
    (II) RADEON(0): Output LVDS has no monitor section
    (II) RADEON(0): Output S-video has no monitor section
    (II) RADEON(0): Output VGA-0 disconnected
    (II) RADEON(0): Output DVI-0 disconnected
    (II) RADEON(0): Output LVDS connected
    (II) RADEON(0): Output S-video disconnected
    (II) RADEON(0): Using user preference for initial modes
    (II) RADEON(0): Output LVDS using initial mode 1024x768
    (II) RADEON(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
    (II) RADEON(0): mem size init: gart size :fdff000 vram size: s:2000000 visible:1f00000
    (II) RADEON(0): EXA: Driver will not allow EXA pixmaps in VRAM
    (==) RADEON(0): DPI set to (96, 96)
    (II) Loading sub module "fb"
    (II) LoadModule: "fb"
    (II) Loading /usr/lib/xorg/modules/libfb.so
    (II) Module fb: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.0.0
    ABI class: X.Org ANSI C Emulation, version 0.4
    (II) Loading sub module "ramdac"
    (II) LoadModule: "ramdac"
    (II) Module "ramdac" already built-in
    (II) Loading sub module "exa"
    (II) LoadModule: "exa"
    (II) Loading /usr/lib/xorg/modules/libexa.so
    (II) Module exa: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 2.5.0
    ABI class: X.Org Video Driver, version 6.0
    (--) Depth 24 pixmap format is 32 bpp
    (II) RADEON(0): [DRI2] Setup complete
    (II) RADEON(0): Front buffer size: 3072K
    (II) RADEON(0): VRAM usage limit set to 25804K
    (==) RADEON(0): Backing store disabled
    (II) RADEON(0): Direct rendering enabled
    (II) RADEON(0): Render acceleration enabled for R100 type cards.
    (II) RADEON(0): Setting EXA maxPitchBytes
    (**) RADEON(0): Option "MigrationHeuristic" "greedy"
    (**) RADEON(0): Option "EXANoComposite" "false"
    (II) EXA(0): Driver allocated offscreen pixmaps
    (II) EXA(0): Driver registered support for the following operations:
    (II) Solid
    (II) Copy
    (II) Composite (RENDER acceleration)
    (II) UploadToScreen
    (II) DownloadFromScreen
    (II) RADEON(0): Acceleration enabled
    (**) RADEON(0): DPMS enabled
    (==) RADEON(0): Silken mouse enabled
    (II) RADEON(0): Set up textured video
    (II) RADEON(0): RandR 1.2 enabled, ignore the following RandR disabled message.
    (WW) RADEON(0): Option "MergedFB" is not used
    (WW) RADEON(0): Option "FBTexPercent" is not used
    (WW) RADEON(0): Option "GARTSize" is not used
    (WW) RADEON(0): Option "AGPMode" is not used
    (--) RandR disabled
    (II) Initializing built-in extension Generic Event Extension
    (II) Initializing built-in extension SHAPE
    (II) Initializing built-in extension MIT-SHM
    (II) Initializing built-in extension XInputExtension
    (II) Initializing built-in extension XTEST
    (II) Initializing built-in extension BIG-REQUESTS
    (II) Initializing built-in extension SYNC
    (II) Initializing built-in extension XKEYBOARD
    (II) Initializing built-in extension XC-MISC
    (II) Initializing built-in extension SECURITY
    (II) Initializing built-in extension XINERAMA
    (II) Initializing built-in extension XFIXES
    (II) Initializing built-in extension RENDER
    (II) Initializing built-in extension RANDR
    (II) Initializing built-in extension COMPOSITE
    (II) Initializing built-in extension DAMAGE
    (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
    (II) AIGLX: enabled GLX_SGI_make_current_read
    (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
    (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
    (II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/radeon_dri.so
    (II) GLX: Initialized DRI2 GL provider for screen 0
    (II) RADEON(0): Setting screen physical size to 270 x 203
    (**) Option "Protocol" "ExplorerPS/2"
    (**) Mouse0: Device: "/dev/input/mice"
    (**) Mouse0: Protocol: "ExplorerPS/2"
    (**) Option "CorePointer"
    (**) Mouse0: always reports core events
    (**) Option "Device" "/dev/input/mice"
    (**) Option "Emulate3Buttons" "on"
    (**) Mouse0: Emulate3Buttons, Emulate3Timeout: 50
    (**) Option "ZAxisMapping" "4 5"
    (**) Mouse0: ZAxisMapping: buttons 4 and 5
    (**) Mouse0: Buttons: 9
    (**) Mouse0: Sensitivity: 1
    (II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
    (**) Mouse0: (accel) keeping acceleration scheme 1
    (**) Mouse0: (accel) acceleration profile 0
    (II) Mouse0: ps2EnableDataReporting: succeeded
    (II) Synaptics touchpad driver version 1.2.1
    (--) SynapticsTouchpad auto-dev sets device to /dev/input/event7
    (**) Option "Device" "/dev/input/event7"
    (II) SynapticsTouchpad: x-axis range 1472 - 5472
    (II) SynapticsTouchpad: y-axis range 1408 - 4448
    (II) SynapticsTouchpad: pressure range 0 - 255
    (II) SynapticsTouchpad: finger width range 0 - 0
    (II) SynapticsTouchpad: buttons: left right double triple
    (**) Option "VertEdgeScroll" "true"
    (--) SynapticsTouchpad: touchpad found
    (**) Option "AlwaysCore" "true"
    (**) Option "SendCoreEvents"
    (**) SynapticsTouchpad: always reports core events
    (II) XINPUT: Adding extended input device "SynapticsTouchpad" (type: TOUCHPAD)
    (**) SynapticsTouchpad: (accel) keeping acceleration scheme 1
    (**) SynapticsTouchpad: (accel) acceleration profile 0
    (--) SynapticsTouchpad: touchpad found
    (**) Option "CoreKeyboard"
    (**) Keyboard0: always reports core events
    (**) Option "Protocol" "standard"
    (**) Keyboard0: Protocol: standard
    (**) Option "XkbRules" "base"
    (**) Keyboard0: XkbRules: "base"
    (**) Option "XkbModel" "pc105"
    (**) Keyboard0: XkbModel: "pc105"
    (**) Option "XkbLayout" "us"
    (**) Keyboard0: XkbLayout: "us"
    (**) Option "CustomKeycodes" "off"
    (**) Keyboard0: CustomKeycodes disabled
    (II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
    (II) config/hal: Adding input device TPPS/2 IBM TrackPoint
    (II) AutoAddDevices is off - not adding device.
    (EE) config/hal: NewInputDeviceRequest failed (8)
    (II) config/hal: Adding input device ThinkPad Extra Buttons
    (II) AutoAddDevices is off - not adding device.
    (EE) config/hal: NewInputDeviceRequest failed (8)
    (II) config/hal: Adding input device Macintosh mouse button emulation
    (II) AutoAddDevices is off - not adding device.
    (EE) config/hal: NewInputDeviceRequest failed (8)
    (II) config/hal: Adding input device SynPS/2 Synaptics TouchPad
    (II) AutoAddDevices is off - not adding device.
    (EE) config/hal: NewInputDeviceRequest failed (8)
    (II) config/hal: Adding input device AT Translated Set 2 keyboard
    (II) AutoAddDevices is off - not adding device.
    (EE) config/hal: NewInputDeviceRequest failed (8)
    (II) config/hal: Adding input device Sleep Button
    (II) AutoAddDevices is off - not adding device.
    (EE) config/hal: NewInputDeviceRequest failed (8)
    (II) config/hal: Adding input device Video Bus
    (II) AutoAddDevices is off - not adding device.
    (EE) config/hal: NewInputDeviceRequest failed (8)
    (II) config/hal: Adding input device Power Button
    (II) AutoAddDevices is off - not adding device.
    (EE) config/hal: NewInputDeviceRequest failed (8)
    (II) AIGLX: Suspending AIGLX clients for VT switch
    (II) Open ACPI successful (/var/run/acpid.socket)
    (II) AIGLX: Resuming AIGLX clients after VT switch
    (II) Mouse0: ps2EnableDataReporting: succeeded
    (--) SynapticsTouchpad: touchpad found

Maybe you are looking for