Radio interface Problem in Air-lap1131-a-k9

I have one Air-lap1131-a-k9 and i convert in autonomus system , but when the AP reload the message " the interface radio is not present " apper
so when i type sh run the interfaces radio dont apper...
Please help me

Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(21a)JY, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 28-Apr-10 10:40 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 150 files, 8 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 10304512
flashfs[1]: Bytes available: 5694464
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Radio0 not present 0 0 0 0 0 3
Radio1 not present 0 0 0 0 0 2
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
[email protected]. AIR-LAP1131AG-A-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FTX1253N1KJ
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
If
cisco
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:23:04:B7:BA:8C
Part Number                          : 73-8962-14
PCA Assembly Number                  : 800-24818-13
PCA Revision Number                  : A0
PCB Serial Number                    : FOC125002LQ
Top Assembly Part Number             : 800-29144-03
Top Assembly Serial Number           : FTX1253N1KJ
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-A-K9 
Press RETURN to get started!
*Mar  1 00:00:06.194: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS  SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 28-Apr-10 10:40 by prod_rel_team
*Mar  1 00:00:54.649: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Mar  1 00:00:55.601: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
ap>
ap>
ap>en
Password:
*Mar  1 00:01:06.553: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar  1 00:01:07.553: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
Password:
ap#sh run
Building configuration...
Current configuration : 731 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$yzUD$BN8tHBfXumwWzTMN9YDj20
no aaa new-model
dot11 syslog
username Cisco password 7 1531021F0725
bridge irb
--More--                           !
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp client-id FastEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
--More--                           line vty 0 4
login local
end
ap#
ap#sh      hardware
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(21a)JY, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 28-Apr-10 10:40 by prod_rel_team
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (
fc2)
ap uptime is 3 minutes
System returned to ROM by power-on
System image file is "flash:/c1130-k9w7-mx.124-21a.JY/c1130-k9w7-mx.124-21a.JY"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
[email protected]. AIR-LAP1131AG-A-K9   (PowerPCElvis) processor (revision A0) with 24566K/81
92K bytes of memory.
Processor board ID FTX1253N1KJ
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
If
cisco
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:23:04:B7:BA:8C
Part Number                          : 73-8962-14
PCA Assembly Number                  : 800-24818-13
PCA Revision Number                  : A0
PCB Serial Number                    : FOC125002LQ
Top Assembly Part Number             : 800-29144-03
Top Assembly Serial Number           : FTX1253N1KJ
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-A-K9
Configuration register is 0xF
ap#         sh un
ap#         sh inv
ap#         sh inventory
NAME: "AP1130", DESCR: "Cisco Aironet 1130 Series (IEEE 802.11a/g) Access Point"
PID: AIR-LAP1131AG-A-K9, VID: V05, SN: FTX1253N1KJ

Similar Messages

  • Problem Cisco AIR-LAP1131AG-E-K9 Ethernet LED = Off; Radio LED = RED ; Status LED = RED ;

    hi,
    I have a Cisco AIR-LAP1131AG-E-K9 when I boot one accesspoint it gives  Ethernet LED = Off; Radio LED = RED ; Status LED = RED  and only next listing in the screen:
    Xmodem file system is available.
    Flashfs[0]: unable to allocate available block.
    The system has been interrupted, or encountered an error during initializion of the flash filesystem.
    The foolowing commands will initialize the flash filesystem, and finish loading the operating system software:
    flash_init
    ether_init
    tftp_init
    boot
    When I type this commands, it doesn't help at all. The output will be following:
    ap: flash_init
    Initializing Flash...
    flashfs[0]: out of memory
    ...done Initializing Flash.
    ap: ether_init
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    ap: tftp_init
    Unable to get our ip address: no "IP_ADDR" variable set
    ap: boot
    Loading ""...; permission denied
    Error loading ""
    Interrupt within 5 seconds to abort boot process.
    Boot process failed...
    ap:
    what i do ?  please help , thanks

    Duplicate posts.  
    Go here:  http://supportforums.cisco.com/discussion/12154826/problem-cisco-air-lap1131ag-e-k9-ethernet-led-radio-led-red-status-led-red

  • AP show in WLC but no radio interfaces

    I am have a problem with couple of our APs the model is AIR-LAP1131AG-A-K9 and we have a Cisco 4404 WLC. 2 of them show up on the controller but have no radio interfaces. I have a I have restarted the AP, reset to factory config all to no avail. When I restart or reset it does communicate with the controller, but still no a/b/g/n radios.
    Anyone have any ideas? Here is a snippet from the log when I restart the AP.
    I would appreciate and pointers here.
    Mar 24 14:20:23.948: [ERROR] spam_lrad.c 2016: AP 00:1d:a2:80:75:dc associated. Last AP failure was due to Link Failure
    Mar 24 14:20:23.948 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.948 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.946 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.946 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.946 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.946 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.946 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.946 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.903: [ERROR] spam_lrad.c 7012: 00:1d:a2:80:75:dc AP Country changed from:() to (US ).
    Mar 24 14:20:23.903: [ERROR] spam_lrad.c 6694: AP 00:1d:a2:80:75:dc: Invalid country code ().
    Mar 24 14:20:23.902: [ERROR] spam_lrad.c 7012: 00:1d:a2:80:75:dc AP Country changed from:() to (US ).
    Mar 24 14:20:23.902: [ERROR] spam_lrad.c 6694: AP 00:1d:a2:80:75:dc: Invalid country code ().

    Hi Rob,
    The WLC version is 4.1.171.0. I have been browsing the conversations here and there seems to a few that are having similar issues. I can't find anything related to this except this:
    CSCsl90841-After you upgrade a controller to software release 4.2.61.0, any access point that does not have region coding (such as the Airespace 1250 access point) is unable to join the controller. An "Invalid country code" message with a country code of 0xFFFF appears in the output of the debug lwapp events enable command.
    Workaround: Downgrade the controller to software release 4.1.
    And I am already on that version. This is rather bizarre. I am working from home for the next few day so I can't physically go pull the AP to look at the codes.
    It does associate with the controller but it just doesn't show any radio interfaces ie, a/b/g/n.
    When I go in and look at that AP on the controller it show everything including the country fine except for the radios. Very confusing.

  • Aironet C1140 - Radio Interface Keeps in Reset State

    Hello,
    Recently we noticed that one of our C1142 access points has a radio interface (actually is only happening with the one working in BG, so its dot11radio 0) which is entering in reset state and doesn't leave that state. I've seen an older thread about similar (or equal?) issue but was on a different AP model (C1240 if I remember correctly).
    The radio interface controller information displays in the end a reset code:
    Last radio reset code: 06
    Radio resets - total:1 retries:0 failed:0
       Code/Count: 06/00001
    Although I was not able to find any information about this reset code in Cisco documents (maybe someone knows where I find it?).
    If I try to restart the interface via "shutdown" configuration command it doesn't fix the problem, the workaround that I know of is only by "reload"ing the whole accesspoint.
    Of course while in reset state no client can associate to this interface....
    Did anyone had similar problem? is there any documented BUG related to this?
    Thanks for your time,
    Jean-François Mousinho
    PS: firmware version is 12.4(21a)JA1.

    version information:
    Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2009 by Cisco Systems, Inc.
    Compiled Wed 16-Sep-09 18:09 by prod_rel_team
    ROM: Bootstrap program is C1140 boot loader
    BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1)
    TS_Piso8_SulEsq uptime is 3 days, 1 hour, 16 minutes
    System returned to ROM by reload
    System restarted at 10:47:38 Z Tue Sep 14 2010
    System image file is "flash:/c1140-k9w7-mx.124-21a.JA1/c1140-k9w7-mx.124-21a.JA1"
    This product contains cryptographic features and is subject to United...
    cisco AIR-AP1142N-E-K9     (PowerPC405ex) processor (revision B0) with 98294K/32768K bytes of memory.
    Processor board ID FCZ1426W04V
    PowerPC405ex CPU at 586Mhz, revision number 0x147E
    Last reset from reload
    1 Gigabit Ethernet interface
    2 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: C8:4C:75:AE:8A:CC
    Part Number                          : 73-11451-08
    PCA Assembly Number                  : 800-30554-06
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC14233KEB
    Top Assembly Part Number             : 800-31273-04
    Top Assembly Serial Number           : FCZ1426W04V
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-AP1142N-E-K9   
    Configuration register is 0xF
    TS_Piso8_SulEsq#sh inventory
    NAME: "AP1140", DESCR: "Cisco Aironet 1140 Series (IEEE 802.11n) Access Point"
    PID: AIR-AP1142N-E-K9  , VID: V03, SN: FCZ1426W04V
    Country is Portugal.
    Thanks for your time.
    Jean-François Mousinho

  • Cisco 1142AP Autonomous - Radio interface constantly reset and provides crash file

    Hello All,
    We have 10 Cisco 1142 Access Points currently configured as Autonomous and I'm experiecing very unusual behavior with the 2.4GHz radio interfaces on each of them. The IOS firmware is 15.2.2JB and they're connected to Cisco 2960 PoE switches. I'm not sure what could be causing this problem however it is service impacting and looks bad on me since I don't have a solution for it. One potential fix could be to upgrade the firmware to 15.2.4 but I'm sure if it is a firmware problem. Any advice would help. Here's an excerpt from the AP log:
    Aug 18 14:40:16:  Writing driver stats to flash:/ap_log_r0_0.log..
    Aug 18 14:40:21:
    Aug 18 14:40:21: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    Aug 18 14:40:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    Aug 18 14:40:23: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    Aug 18 14:40:23: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    Thanks,
    Ali Ibrahim

    You should be able to go in and view teh R0_0.log file.
    there might be something in there that you can do a bug search for.
    HTH,
    Steve

  • Radio Interface Reset and Shutdown Frequently

    As recently new office from end-Sept, we have found that the radio interface reset very frequently which has been  happening about over 15 times within 8 weeks for one AP on average. Some of  those (3 AP so far) got the radio interface down eventually and we need to  reload the AP to make it up again.
    the AP model is AIR-LAP1142N-N-K9 and the IOS version is
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:表格內文;
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-fareast-font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    st1\:*{behavior:url(#ieooui) }
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:表格內文;
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-fareast-font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    c1140-k9w7-mx.124-21a.JA1. Power supply is made from the PoE switch c2960s. Is there any issue related to IOS? or some other factors may cause the issue happen? Any debug command can show the status of AP? Please advice.

    Hi Surendra,
    Other than IOS, will this radio interface reset and shutdown issue affect by the nearby AP which is not belongs to the same office.
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-fareast-font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    Scenario:
    The new office gets 2 floors. One is 5/F which has installed 9 APs with different channels and another one is 6/F which has installed 6 APs with different channels as well. We found that there are many events “%DOT11-4-MAXRETRIES: Packet to client reached max retries, removing the client” logged on 5/F and 6/F AP.
    We also found that the radio interface reset very frequently which has been happening about over 15 times within 8 weeks for one AP on average. Some of those (3 AP so far) got the radio interface down eventually and we need to reload the AP to make it up again.
    Is/ are there any possibility caused by otherenvironmental factors? Please advise.
    Best regards,
    Bell

  • 1200 AP missing radio interface

    hi i have a 1200 ap and its radio interface is missing. i mean i am uanble to see its radio interface
    I really need this urgently.Anybody can help me

    cisco AIR-AP1231G-A-K9 (PowerPC405GP) processor (revision A0) with 14838K/1536K bytes of memory.
    Processor board ID FOC09501XL4
    PowerPC405GP CPU at 196Mhz, revision number 0x0145
    Last reset from power-on
    1 FastEthernet interface
    1 802.11 Radio(s)
    That was from an AP with the radio installed.
    Your config
    cisco AIR-AP1230B-E-K9 (PowerPC405GP) processor (revision A0) with 14326K/2048K bytes of memory.
    Processor board ID FOC07410KFY
    PowerPC405GP CPU at 196Mhz, revision number 0x00C4
    Last reset from power-on
    Bridging software.
    1 FastEthernet/IEEE 802.3 interface(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Yours doesn't show a radio module installed,
    You need a radio module

  • Dot11 radio interface reset protocol down

    I have a cisco 1400 that that show interface show int dott1 radio interface reset protocol down. I had a surge in the area and had the problem after. I copied the config over to a new Ap and power injector and the problem persists. The bridge is the non root bridge. I had read a caveat cscea75989 but it said take no action. Take no action is not fixing my problem at this time. Any suggestions would be appreciated. Thanks.

    There are a number of known issues on this. One which sounds similar is CSCea45031. Check if you are hitting the same.

  • Cisco 1142N Radio interface gone

    Hi All,
    I have around 20 1142Ns registered to 4402 WLC. WLC was saying:
         802.11a/n Radios     20
         802.11b/g/n Radios     19
    So I compared and found the AP which had only 802.11a/n Radio. SSH-d to the AP and sh ver:
    1 Gigabit Ethernet interface
    1 802.11 Radio(s)
    and if I try to configure the radio interface:
    apname(config)#interface dot11Radio ?
      <0-1>  Dot11Radio interface number
    apname(config)#interface dot11Radio 0?
    .  :  <0-1>
    apname(config)#interface dot11Radio 0 ?
    % Unrecognized command
    apnameconfig)#interface dot11Radio 1 ?
      <cr>
    So as you can see dot11Radio 0 is gone. I've tried rebooting the AP with no success. I'm thinking there is a hardware failure with the radio antenna.
    Has anyone experienced this kind of problem? What could be the cause?
    Thanks,
    Delgee

    Converted to autonomous, upgraded bootstrap:
    ROM: Bootstrap program is C1140 boot loader
    BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA1, RELEASE SOFTWARE (fc1)
    Converted back to lightweight and the problem is still same:
    APxxxx.xxxx.xxxx#sh ip int br
    Interface                  IP-Address      OK? Method Status                Protocol
    Dot11Radio1                unassigned      NO  unset  up                    up
    GigabitEthernet0           x.x.x.x       YES DHCP   up                    up
    LWAPP image version 7.0.98.0
    1 Gigabit Ethernet interface
    1 802.11 Radio(s)
    Guess the only option left is to get it replaced under its warranty.

  • Radio Interface Locks Up, Jams Up Clients

    Hi there, got a problem with the radio interface on AP350s and 1200s (11b & g, running IOS), occasionally (and not on the same units) the RF interface will lock up and any clients associated to it will not be pingable and lose network connectivity. Doing a shut/no shut (and usually a reload) bumps the clients off to other APs where they're pingable once more. This happens to Cisco and non-Cisco radioed devices, the APs aren't running anything fancy like WDS, just default config. and WEP. The 350s never had this problem running VxWorks but started this behavior when upgraded to IOS. I'm real disappinted the 1200s are doing the same thing. When the lock ups happen it causes major problems at our locations and I need to find a cure...now! Any ideas anyone? Thanks.

    Scott,
    The 350s use the IOS upgrade image, the 1200s use the latest IOS version. The only rogue APs I have problems with are the Ciscos running IOS! Symbol and first generation 802.11b Aironet (pre-Cisco) APs aren't afflicted with this problem even in a mixed AP environment. In locations that are all Cisco APs and devices we still get this problem. The APs are in locations countrywide and away from Joe Public, and no other WLANs nearby. I think, I HOPE it's just a config. problem but all the APs have (more or less) the same standard config. and the issue strikes APs randomly. As advised, as soon as you do a shut/no shut everything's OK...the devices that got bumped off by the s/ns usually 'roam' back to the AP that had the issue within a few seconds or minutes and are pingable once more from the AP's radio interface. I was paged while typing my question last evening and when I went to check, guess what, another 350 with 6 clients (all Cisco devices) all jammed up on it. Shut/No Shut and carry on like nothing happened. If you've got any suggestions I'll take them, I've not had much luck on the Cisco web site, I'll probably have to put in a TAC case at some point soon as I've got better things to do than go around resetting APs. I was even thinking about rebooting our Cisco AP complement once a week in case it was some sort of caching/ARP problem.
    Thanks in advance for any pearls of wisdom!

  • Radio interface

    I am trying to get a DD-WRT router to function as a client bridge on a wireless network off of a 871 router. When the DD-WRT device is configured, you can ping the device from ANY other device on the network except for the 871 and the devices behind the 871 have no internet access. I was thinking that the bridge-group 1 block-unknown-source command on the radio interface might be the problem but it cannot be removed and is an automatic command.
    Does anyone know of a way to either remove this command or to have the bridged device MAC be 'learned'?

    What's a DD-WRT router? It looks like you're using an 871 with a wireless module. Are you trying to bridge something non-Cisco off of the 871? If not, what exactly are you doing, and what are you using each device for? Is the 871 a remote router that has clients hanging off of it that need to pass over a WAN link of some kind to get to the Internet?
    Try applying your command to a subinterface if you have multiple VLANs. Otherwise, if you'd like to post some more information, I'd be glad to help if I can.

  • Interface Problems in Yosemite

    Problem shows up when using software other than the native OS X apps.
    If I attempt to close a window behind the app that has focus by clicking the red x part of the semaphore buttons (top left on every window) it will not work unless I change focus to that app by clicking the bar at the top.
    As an example if I'm using Byword to view a document while composing an email in Airmail once I finished and move on to viewing, say a receipt, in Airmail and want to make a copy of that receipt and place it on the desktop. I'm done with Byword and it is covering the desktop so why not close it and get it out of the way. I move the mouse pointer over the red X part of the semaphore buttons and click, nothing happens. I have to bring Byword into focus by clicking the title bar, then click the red x to finally close the window. If the app below Airmail happened to be Safari the red X works properly.
    On my Mac Mini using Yosemite this works properly for all apps.
    This is only a slight problem but I have been having the odd quirky interface problems for the past while and I'm worried that something has gone south and these may end up adding together to make a very large problem.  Initially I had problems with PopClip which seemed to be screwing around with the interface buttons in Rapidweaver 6. I removed the app to clear that problem using AppDelete.
    While trying to diagnose this problem I have removed all the auto login apps that I can and rebooted several times to no avail.
    Any help would be greatly appreciated!
    EtreCheck version: 2.1.8 (121) log:
    EtreCheck version: 2.1.8 (121)
    Report generated February 5, 2015 at 12:32:53 PM EST
    Download EtreCheck from http://etresoft.com/etrecheck
    Click the [Click for support] links for help with non-Apple products.
    Click the [Click for details] links for more information about that line.
    Hardware Information: ℹ️
        iMac (27-inch, Late 2012) (Technical Specifications)
        iMac - model: iMac13,2
        1 3.4 GHz Intel Core i7 CPU: 4-core
        8 GB RAM Upgradeable
            BANK 0/DIMM0
                4 GB DDR3 1600 MHz ok
            BANK 1/DIMM0
                4 GB DDR3 1600 MHz ok
            BANK 0/DIMM1
                Empty 
            BANK 1/DIMM1
                Empty 
        Bluetooth: Good - Handoff/Airdrop2 supported
        Wireless:  en1: 802.11 a/b/g/n
    Video Information: ℹ️
        NVIDIA GeForce GTX 680MX - VRAM: 2048 MB
            iMac 2048 x 1152
    System Software: ℹ️
        OS X 10.10.2 (14C109) - Time since boot: 0:0:46
    Disk Information: ℹ️
        APPLE HDD WDC WD10EALX-408EA0 disk1 : (1 TB)
            EFI (disk1s1) <not mounted> : 210 MB
            Recovery HD (disk1s3) <not mounted>  [Recovery]: 650 MB
            Macintosh HD (disk2) / : 1.11 TB (263.43 GB free)
                Core Storage: disk0s2 120.99 GB Online
                Core Storage: disk1s2 999.35 GB Online
        APPLE SSD SM128E disk0 : (121.33 GB)
            EFI (disk0s1) <not mounted> : 210 MB
            Boot OS X (disk0s3) <not mounted> : 134 MB
            Macintosh HD (disk2) / : 1.11 TB (263.43 GB free)
                Core Storage: disk0s2 120.99 GB Online
                Core Storage: disk1s2 999.35 GB Online
    USB Information: ℹ️
        Verbatim Portable USB 3.0 Drive 1 TB
            EFI (disk3s1) <not mounted> : 210 MB
            Verbatim HD (disk3s2) /Volumes/Verbatim HD : 999.86 GB (31.06 GB free)
        Apple Inc. FaceTime HD Camera (Built-in)
        Logitech USB Receiver
        Samsung Electronics Co., Ltd. ML-2160 Series
        Wacom Co.,Ltd. Wacom Wireless Receiver
        Razer Razer 1600dpi Mouse
        Apple Inc. BRCM20702 Hub
            Apple Inc. Bluetooth USB Host Controller
    Thunderbolt Information: ℹ️
        Apple Inc. thunderbolt_bus
    Gatekeeper: ℹ️
        Mac App Store and identified developers
    Kernel Extensions: ℹ️
            /Applications/Transmit.app
        [not loaded]    com.panic.TransmitDisk.transmitdiskfs (4.0.0 - SDK 10.6) [Click for support]
            /Applications/VMware Fusion.app
        [not loaded]    com.vmware.kext.vmci (90.6.3) [Click for support]
        [not loaded]    com.vmware.kext.vmioplug.14.1.3 (14.1.3) [Click for support]
        [not loaded]    com.vmware.kext.vmnet (0231.47.74) [Click for support]
        [not loaded]    com.vmware.kext.vmx86 (0231.47.74) [Click for support]
        [not loaded]    com.vmware.kext.vsockets (90.6.0) [Click for support]
            /Library/Extensions
        [loaded]    at.obdev.nke.LittleSnitch (4234 - SDK 10.8) [Click for support]
        [loaded]    com.avatron.AVExFramebuffer (1.7 - SDK 10.9) [Click for support]
        [loaded]    com.avatron.AVExVideo (1.7 - SDK 10.9) [Click for support]
        [loaded]    com.globaldelight.driver.Boom2Device (1.1 - SDK 10.10) [Click for support]
        [loaded]    com.logitech.manager.kernel.driver (4.10.1 - SDK 10.8) [Click for support]
        [loaded]    com.sophos.kext.sav (9.2.50 - SDK 10.8) [Click for support]
        [loaded]    com.sophos.nke.swi (9.2.50 - SDK 10.8) [Click for support]
        [not loaded]    com.wacom.kext.ftdi (1 - SDK 10.9) [Click for support]
            /System/Library/Extensions
        [loaded]    com.Logitech.Control Center.HID Driver (3.7.0 - SDK 10.6) [Click for support]
        [loaded]    com.Logitech.Unifying.HID Driver (1.3.0 - SDK 10.6) [Click for support]
        [loaded]    com.eltima.SyncMate.kext (0.2.5b15) [Click for support]
        [loaded]    com.globaldelight.driver.BoomDevice (1.1 - SDK 10.1) [Click for support]
        [loaded]    com.splashtop.driver.SRXDisplayCard (1.6 - SDK 10.7) [Click for support]
        [not loaded]    com.splashtop.driver.SRXFrameBufferConnector (1.6 - SDK 10.7) [Click for support]
        [not loaded]    com.wacom.kext.wacomtablet (6.3.10 - SDK 10.9) [Click for support]
            /System/Library/Extensions/Soundflower.kext
        [not loaded]    com.Cycling74.driver.Soundflower (1.6.6 - SDK 10.6) [Click for support]
    Launch Agents: ℹ️
        [running]    at.obdev.LittleSnitchUIAgent.plist [Click for support]
        [not loaded]    com.adobe.AAM.Updater-1.0.plist [Click for support]
        [running]    com.Logitech.Control Center.Daemon.plist [Click for support]
        [running]    com.logitech.manager.daemon.plist [Click for support]
        [loaded]    com.oracle.java.Java-Updater.plist [Click for support]
        [running]    com.realvnc.vncserver.peruser.plist [Click for support]
        [not loaded]    com.realvnc.vncserver.prelogin.plist [Click for support]
        [running]    com.sophos.uiserver.plist [Click for support]
        [running]    com.wacom.wacomtablet.plist [Click for support]
    Launch Daemons: ℹ️
        [running]    at.obdev.littlesnitchd.plist [Click for support]
        [loaded]    com.adobe.fpsaud.plist [Click for support]
        [running]    com.backblaze.bzserv.plist [Click for support]
        [loaded]    com.barebones.authd.plist [Click for support]
        [loaded]    com.oracle.java.Helper-Tool.plist [Click for support]
        [loaded]    com.oracle.java.JavaUpdateHelper.plist [Click for support]
        [running]    com.realvnc.vncserver.plist [Click for support]
        [loaded]    com.rogueamoeba.instanton-agent.plist [Click for support]
        [loaded]    com.sharpcast.xfsmond.plist [Click for support]
        [loaded]    com.sheepsystems.CocoaPrivilegedHelper.plist [Click for support]
        [running]    com.sophos.common.servicemanager.plist [Click for support]
        [loaded]    de.appgineers.Mountain.Helper.plist [Click for support]
    User Launch Agents: ℹ️
        [loaded]    com.adobe.AAM.Updater-1.0.plist [Click for support]
        [running]    com.backblaze.bzbmenu.plist [Click for support]
        [running]    com.ecamm.printopia.plist [Click for support]
        [loaded]    com.google.keystone.agent.plist [Click for support]
        [loaded]    com.pia.pia_manager.plist [Click for support]
        [loaded]    com.sheepsystems.BookMacster.3EAE0703-42...plist [Click for support]
        [loaded]    com.sheepsystems.BookMacster.3EAE0703-42...plist [Click for support]
        [loaded]    com.valvesoftware.steamclean.plist [Click for support]
        [failed]    ws.agile.1PasswordAgent.plist [Click for support] [Click for details]
    User Login Items: ℹ️
        WD Quick View    Application  (/Library/Application Support/WDSmartware/WDQuickView.app)
    Internet Plug-ins: ℹ️
        FlashPlayer-10.6: Version: 16.0.0.305 - SDK 10.6 [Click for support]
        QuickTime Plugin: Version: 7.7.3
        Flash Player: Version: 16.0.0.305 - SDK 10.6 [Click for support]
        WacomNetscape: Version: 2.1.0-1 - SDK 10.8 [Click for support]
        Default Browser: Version: 600 - SDK 10.10
        GarminGpsControl: Version: 4.0.2.6 Beta - SDK 10.6 [Click for support]
        WacomTabletPlugin: Version: WacomTabletPlugin 2.1.0.6 - SDK 10.9 [Click for support]
        JavaAppletPlugin: Version: Java 8 Update 31 Check version
    User internet Plug-ins: ℹ️
        Picasa: Version: 1.0 - SDK 10.6 [Click for support]
    Safari Extensions: ℹ️
        1Password
        Clip to DEVONthink
        Choosy
        Ember
        Save to Pocket
        Stache
    3rd Party Preference Panes: ℹ️
        AirServer Preferences  [Click for support]
        Backblaze Backup  [Click for support]
        Choosy  [Click for support]
        Flash Player  [Click for support]
        FUSE for OS X (OSXFUSE)  [Click for support]
        Hazel  [Click for support]
        Java  [Click for support]
        Logitech Control Center  [Click for support]
        Logi Preference Manager  [Click for support]
        Printopia  [Click for support]
        WacomTablet  [Click for support]
        WDQuickView  [Click for support]
        Web Sharing  [Click for support]
    Time Machine: ℹ️
        Skip System Files: NO
        Auto backup: YES
        Volumes being backed up:
            Macintosh HD: Disk size: 1.11 TB Disk used: 848.39 GB
        Destinations:
            Verbatim HD [Local]
            Total size: 999.86 GB
            Total number of backups: 101
            Oldest backup: 2013-11-22 16:26:50 +0000
            Last backup: 2015-02-05 15:55:38 +0000
            Size of backup disk: Too small
                Backup size 999.86 GB < (Disk used 848.39 GB X 3)
    Top Processes by CPU: ℹ️
            12%    mds
             2%    WindowServer
             0%    loginwindow
             0%    fontd
             0%    mds_stores
    Top Processes by Memory: ℹ️
        292 MB    mds_stores
        172 MB    SophosScanD
        172 MB    InterCheck
        155 MB    SophosAntiVirus
        120 MB    Finder
    Virtual Memory Information: ℹ️
        3.32 GB    Free RAM
        2.72 GB    Active RAM
        1.40 GB    Inactive RAM
        1.15 GB    Wired RAM
        1.56 GB    Page-ins
        0 B    Page-outs
    Diagnostics Information: ℹ️
        Feb 5, 2015, 12:30:03 PM    Self test - passed
        Feb 4, 2015, 10:59:58 PM    /Library/Logs/DiagnosticReports/RapidWeaver 6_2015-02-04-225958_[redacted].cpu_resource.diag [Click for details]
        Feb 3, 2015, 03:07:17 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/WebKitPluginHost_2015-02-03-15 0717_[redacted].crash
        Feb 3, 2015, 03:02:23 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/WebKitPluginHost_2015-02-03-15 0223_[redacted].crash
        Jan 15, 2015, 08:04:41 PM    /Library/Logs/DiagnosticReports/Kernel_2015-01-15-200441_[redacted].panic [Click for details]

    Try un-installing Sophos.
    Sophos Un-install

  • Cisco Wireless AP radio interface shutdown/Operation Status Down

    Hi,
    I am trying to troubleshoot the cause of the wireless AP 1142 radio shutdown; I was wondering where may be a good place to start on it/possibility of the radio shutting down. Once the radio is shown as down; I would just need to re-enable (disable/enable) it and the status changes to up status. I have attached a screen catpure of the radio interface showning down.
    The AP radios shutting down is intermittent; some APs has their "A/N" radio interface shutdown while others has their "G/N" radio interface shutdown. Not too sure what may most likely be causing it to shutdown?
    Any input is appreciated.
    Thanks.

    Do you have controller ?? if yes then posts out put of sh sysinfo commad.
    Paste the output of sh version command from AP.
    Also check: 
    1. Choose Wireless > 802.11a/n or 802.11b/g/n > Network
    Select the 802.11a (or 802.11b/g) Network Status check box to enable the 802.11a or 802.11b/g band.
    2. Wireless > Access Points > All APs then click on specific AP and make sure admin status is enable.
    Reagrds

  • Interface Problems: DBA = Data Pump = Export Jobs (Job Name)

    Hello Folks,
    I need your help in troubleshooting an SQL Developer interface problem.
    DBA => Data Pump => Export Jobs (Job Name) => Data Pump Export => Job Scheduler (Step):
    -a- Job Name and Job Description fields are not visible. Well the fields are there but each of them just 1/2 character wide. I can't see/enter anything in the fields.
    Import Wizard:
    -b- Job Name field under the first "Type" wizard's step looks exactly the same as in Export case.
    -c- Can't see any row under "Chose Input Files" section (I see just ~1 mm of the first row and everything else is hidden).
    My env:
    -- Version 3.2.20.09, Build MAIN-09.87
    -- Windows 7 (64 bit)
    It could be related to the fact that I did change fonts in the Preferences. As I don't know what is the default font I can't change it back to the default and test (let me know what is the default and I will test it).
    PS
    -- Have tried to disable all extensions but DBA Navigator (11.2.0.09.87). It didn't help
    -- There are no any messages in the console if I run SQL Dev under cmd "sqldeveloper\bin\sqldeveloper.exe
    Any help is appreciated,
    Yury

    Hi Yury,
    a-I see those 1/2 character size text boxes (in my case on frequency) when the pop up dialog is too small - do they go away when you make it bigger?
    b- On IMPORT the name it starts with IMPORT - if it is the half character issue have you tried making the dialog bigger?
    c-I think it is size again but my dialog at minimum size is already big enough.
    Have you tried a smaller font - or making the dialogs bigger (resizing from the corners).
    I have a 3.2.1 version where I have not changed the fonts from Tools->Preferences->CodeEditor->Fonts appears to be:
    Font Name: DialogInput
    Font size: 12
    Turloch
    -SQLDeveloper Team

  • Radio interface need to be disabled when antenna is not present?

    I have been informed within a training class that the radio interface of an access point should be disabled when an antenna is not present. The reason given was that it would protect the radio from being adversely affected (potetnial for irreparable conditions). Question: 1) Is this true? 2) If so, where can I find supporting documentation on CCO? (I have not been able to find corroboratory information.)

    Hi Vincent,
    Here is a doc that speaks to this issue ( I don't see this causing irreparable damage but, better safe than sorry :)
    Q. If you operate the radio but do not attach the antenna, can you damage the radio?
    A. Some radio equipment manufacturers specifically warn against the operation of radios without the attachment of the antenna. Operation without the antenna can damage the transmitter. Most pieces of amateur or commercial radio equipment carry this warning because the equipment operates at a much higher transmitter power. A failure to use a proper antenna or load causes a reflected wave standing wave ratio (SWR) that can damage the final amplifier stage. This final amplifier stage is the power amplifier (PA).
    For Cisco Aironet equipment, the transmitter power output is 100 milliwatts (mW) for the 350 Series and 30 mW for the 340 Series. Damage is unlikely, but possible. If you need to run the devices without antennae, turn the transmitter power down to 1.5 mW. Also, you can use a 50/52 ohm dummy load (attenuator) to be safe.
    From this good Q & A doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps441/products_qanda_item09186a0080094d01.shtml#aps
    Hope this helps!
    Rob

Maybe you are looking for

  • Mail app v5.3 crashes consistently

    My Mail app v5.3 doesnt open anymore. It crashed for the first time as I was writing an email. Since then, when I click on the Mail icon, it asks whether I wish to reopen the closed window, and regardless of what I select (yes or no) it crashes. I ha

  • Error while generating XSD in MDMGX in CRM

    hi i am trying to generate XSD for article master in CRM . in mdmgx ,  when i click generate XSD ,i get following error. :No customizing entries found for this extraction" if anybody got this same error , please share how  u solved it regards akhil

  • Right Side USB Ports Don't Work on my DV7 6b32US

    I just bought a DV7 6b32US. It's on Windows 7 Home Premium. The left hand side USB slots are okay. but the two on the right side do nothing at all. No message - nada! It seems to be a common issue, but I have no resolution to it. Also, annoyingly, wh

  • Frequent "Invalid URL" problem on my MacBook

    I have a strange problem accessing websites with my MacBook. I'll go to a website like Google, Amazon, Netflix, etc, and intermittently, I'll get the following error message: Invalid URL The requested URL "http://www.netflix.com/", is invalid. Refere

  • IPads in Educations: Schools and Apps

    Hi, We are a school in Ireland and would be considered a 'Digital School'. We've been using tablet PC's for teaching for years and now are interested in iPads. However, being an avid Apple supporter I believe Apple are not yet ready for the education