RADIUS-3-NOSERVERS: No radius hosts configured or no valid server present in the server group

Hi,
I currently have an C2960 switch with IOS 15.0(2) SE4. To log on the CLI of the switch authentication against a RADIUS server takes place. Accounting is not wanted. The config of the switch is as follows:
aaa new-model
aaa group server radius RADIUSGROUP
 server xxx.xxx.xxx.1 auth-port 1812 acct-port 0
 server xxx.xxx.xxx.2 auth-port 1812 acct-port 0
aaa authentication login default group RADIUSGROUP local
aaa authentication dot1x default group RADIUSGROUP
aaaauthorization network default group RADIUSGROUP
radius server host xxx.xxx.xxx.1 auth-port 1812 acct-port 0 key 7 [encrypted password]
radius server host xxx.xxx.xxx.2 auth-port 1812 acct-port 0 key 7 [encrypted password]
It works fine, the authentication and the login are successful, but every login generates a message in the logging of the switch:
RADIUS-3-NOSERVERS: No radius hosts configured or no valid server present in the server group
What is going wrong???
Any help would be appreciated.

    That's going to be something you are going to have to go the cisco TAC with .  That looks to be some kind of software bug.  Also a feature probably not a lot of people actually use and have knowlwedge about.

Similar Messages

  • Unknown Host Unable to locate the server requested --- the server does not have a DNS entry. Perhaps there is a misspelling in the server name, or the server no

    Hello,
    Today i tried accessing transitbux.com with mozilla, but i'm getting this kind of a error as mentioned below:
    Unknown Host
    Description: Unable to locate the server requested --- the server does not have a DNS entry. Perhaps there is a misspelling in the server name, or the server no longer exists. Double-check the name and try again.
    Can anyone help me please, and the same website is accessible with my phone.
    Help me please. :(
    Regards
    -

    Try http://www.transitbux.com/
    Clear the cache and remove cookies only from websites that cause problems.
    "Clear the Cache":
    *Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"
    "Remove Cookies" from sites causing problems:
    *Firefox/Tools > Options > Privacy > "Use custom settings for history" > Cookies: "Show Cookies"

  • The remote desktop session host configuration & Remote session shadowing options missing in Windows server 2012.

    Hi All,
    I am using a Windows server 2012 Standard. When i leave my session idle for more than 20 min it disconnects and post more 20 minutes my session is logged off.
    I know this setting can be changed from Remote desktop session host configuration in Windows server 2008 R2. But this option "Remote desktop session host configuration" is not there in Windows server 2012. Does any one have an idea where do i go
    and edit these settings in the Server 2012 o/s ?
    Also the Remote session shadowing option is also not available when i right click a user in the task manager. Any idea on an alternate method in Windows server 2012 ?
    Gautam.75801

    Exactly WHERE are the W2K12 R2 equivalent GPO settings to W2K8 R2 GPO settings of "Set time limit for disconnected sessions" and "set time limit for active but idle Remote Desktop Services
    sessions"?  Microsoft changed the remote desktop/terminal services around.  
    Appreciate it.
    Matt
     Policy Path 
     Scope 
     Policy Setting Name 
     Windows Components\Remote Desktop   Services\Remote Desktop Session Host\Session Time Limits 
     User 
     End session when time limits are   reached 
     Windows Components\Remote Desktop   Services\Remote Desktop Session Host\Session Time Limits 
     Machine 
     End session when time limits are   reached 
     Windows Components\Remote Desktop   Services\Remote Desktop Session Host\Session Time Limits 
     User 
     Set time limit for disconnected   sessions 
     Windows Components\Remote Desktop   Services\Remote Desktop Session Host\Session Time Limits 
     Machine 
     Set time limit for disconnected   sessions 
     Windows Components\Remote Desktop   Services\Remote Desktop Session Host\Session Time Limits 
     User 
     Set time limit for active but idle   Remote Desktop Services sessions 
     Windows Components\Remote Desktop   Services\Remote Desktop Session Host\Session Time Limits 
     Machine 
     Set time limit for active but idle   Remote Desktop Services sessions 
     Windows Components\Remote Desktop   Services\Remote Desktop Session Host\Session Time Limits 
     User 
     Set time limit for active Remote   Desktop Services sessions 
     Windows Components\Remote Desktop   Services\Remote Desktop Session Host\Session Time Limits 
     Machine 
     Set time limit for active Remote   Desktop Services sessions 
    Don
    (Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
    This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

  • Hosting a Web Dynpro App physically present on another server

    Hello All,
    We are on the process of seperating Web Dynpro applications onto a seperate box, and configuring iViews for them on a dedicated portal server. As part of this:-
    1. I created a new system in the portal. This new system points to the Web Application server holding the Web Dynpros
    2. I configured an Iview using the system mentioned in step 1.
    3. On previewing the same, I am getting the following error...
    java.lang.ClassNotFoundException: com.sapportals.portal.prt.registry.PortalRegistryFactory Found in negative cache -
    Loader Info -
    ClassLoader name: [local/CreateWell]
    The Web Application Server where the Web Dynpros are deployed does'nt have portal configured. Is the error because of that? I find that it is looking for Portal specific class (which would not be there in the WAS because EP is not configured on it).
    Have any one tried a scenario like this?
    Thanks in advance,
    SPK.

    Hello All,
    We are on the process of seperating Web Dynpro applications onto a seperate box, and configuring iViews for them on a dedicated portal server. As part of this:-
    1. I created a new system in the portal. This new system points to the Web Application server holding the Web Dynpros
    2. I configured an Iview using the system mentioned in step 1.
    3. On previewing the same, I am getting the following error...
    java.lang.ClassNotFoundException: com.sapportals.portal.prt.registry.PortalRegistryFactory Found in negative cache -
    Loader Info -
    ClassLoader name: [local/CreateWell]
    The Web Application Server where the Web Dynpros are deployed does'nt have portal configured. Is the error because of that? I find that it is looking for Portal specific class (which would not be there in the WAS because EP is not configured on it).
    Have any one tried a scenario like this?
    Thanks in advance,
    SPK.

  • No Radius hosts configured...

    For days now, I've been trying to troubleshoot an authentication problem and the solution still eludes me.
    I have a Windows 7 SP1 laptop, a wireless client, that should be able to access the wireless network LAB1 with SSID AP1.
    It should authenticate with a Windows 2008 R2 SP1 DC/NPS server via a Cisco Aironet 1142 access point.
    Authentication is "Open with EAP".
    EAP type is EAP-TLS.
    Two entries in the Aironet Event Log, I believe, are related to the problem:
    Error - No Radius hosts configured or no valid server present in the group rad_eap
    Debugging - Station [MAC addr here] Authentication Failed.
    The MAC addr is that of the Windows 7 SP1 laptop attempting to connect to the network via the access point.
    Could someone verify that my configuration is correct for what I want to accomplish (wireless access by laptops using EAP (EAP-TLS) authentication and - for now - WEP encryption???
    Also, what could explain the error message above about no Radius servers? The output of "show run" below seems to indicate that Radius is configured, correctly or not...
    Here is the ouput of the "show run" command on the Aironet 1142 (via telnet) - followed by the error messages in the Windows 7 laptop Event Viewer (WLAN Auto-Config section):
    AP1#sh run
    Building configuration...
    Current configuration : 2354 bytes
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec localtime show-timezone
    service password-encryption
    hostname AP1
    logging rate-limit console 9
    enable secret 5 $1$4Ipo$roPiDJm93XYFOrN7hngx/1
    aaa new-model
    aaa group server radius rad_eap
    aaa group server radius rad_mac
    aaa group server radius rad_acct
    aaa group server radius rad_admin
    aaa group server tacacs+ tac_admin
    aaa group server radius rad_pmip
    aaa group server radius dummy
    aaa authentication login eap_methods group rad_eap
    aaa authentication login mac_methods local
    aaa authorization exec default local
    aaa accounting network acct_methods start-stop group rad_acct
    aaa session-id common
    dot11 syslog
    dot11 ssid AP1
       authentication open eap eap_methods
       authentication network-eap eap_methods
       guest-mode
    username Cisco password 7 00271A150754
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    encryption mode wep mandatory
    ssid AP1
    antenna gain 0
    power local 2
    power client 2
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface Dot11Radio1
    no ip address
    no ip route-cache
    shutdown
    encryption mode wep mandatory
    ssid AP1
    antenna gain 0
    dfs band 3 block
    channel dfs
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface GigabitEthernet0
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    no keepalive
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address 10.0.0.51 255.0.0.0
    no ip route-cache
    ip default-gateway 10.0.0.2
    ip http server
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    ip radius source-interface BVI1
    radius-server attribute 32 include-in-access-req format %h
    radius-server host 10.0.0.12 auth-port 1812 acct-port 1813 key 7 03050A09055D2549485A
    radius-server vsa send accounting
    bridge 1 route ip
    line con 0
    line vty 0 4
    end
    Note: I changed the Radius ports to 1812 and 1813 because that's what Windows uses for Radius (authentication and accounting).
    Windows Event Viewer entries
    Event ID 8000
    WLAN AutoConfig service started a connection to a wireless network.
    Network Adapter: Intel(R) PRO/Wireless 3945ABG Network Connection
    Interface GUID: {16f026bc-d9fd-4a9d-9020-a32174a4bd6a}
    Connection Mode: Automatic connection with a profile
    Profile Name: LAB1
    SSID: AP1
    BSS Type: Infrastructure
    Event ID 11000
    Wireless network association started.
    Network Adapter: Intel(R) PRO/Wireless 3945ABG Network Connection
    Interface GUID: {16f026bc-d9fd-4a9d-9020-a32174a4bd6a}
    Local MAC Address: 00:1C:BF:68:1E:C5
    Network SSID: AP1
    BSS Type: Infrastructure
    Authentication: Open
    Encryption: WEP
    802.1X Enabled: Yes
    Event ID 11001
    Wireless network association succeeded.
    Network Adapter: Intel(R) PRO/Wireless 3945ABG Network Connection
    Interface GUID: {16f026bc-d9fd-4a9d-9020-a32174a4bd6a}
    Local MAC Address: 00:1C:BF:68:1E:C5
    Network SSID: AP1
    BSS Type: Infrastructure
    Peer MAC Address: 64:A0:E7:29:08:E0
    Event ID 11010
    Wireless security started.
    Network Adapter: Intel(R) PRO/Wireless 3945ABG Network Connection
    Interface GUID: {16f026bc-d9fd-4a9d-9020-a32174a4bd6a}
    Local MAC Address: 00:1C:BF:68:1E:C5
    Network SSID: AP1
    BSS Type: Infrastructure
    Peer MAC Address: 64:A0:E7:29:08:E0
    Authentication: Open
    Encryption: WEP
    FIPS Mode: Disabled
    802.1x Enabled: Yes
    Event ID 12011
    Wireless 802.1x authentication started.
    Network Adapter: Intel(R) PRO/Wireless 3945ABG Network Connection
    Interface GUID: {16f026bc-d9fd-4a9d-9020-a32174a4bd6a}
    Local MAC Address: 00:1C:BF:68:1E:C5
    Network SSID: AP1
    BSS Type: Infrastructure
    Peer MAC Address: 64:A0:E7:29:08:E0
    Eap Information: Type 13, Vendor ID 0, Vendor Type 0, Author ID 0
    Event ID 12014
    Wireless 802.1x authentication was restarted.
    Network Adapter: Intel(R) PRO/Wireless 3945ABG Network Connection
    Interface GUID: {16f026bc-d9fd-4a9d-9020-a32174a4bd6a}
    Local MAC Address: 00:1C:BF:68:1E:C5
    Network SSID: AP1
    BSS Type: Infrastructure
    Peer MAC Address: 64:A0:E7:29:08:E0
    Eap Information: Type 13, Vendor ID 0, Vendor Type 0, Author ID 0
    Restart Reason: Peer Initiated
    Event ID 12013
    Wireless 802.1x authentication failed.
    Network Adapter: Intel(R) PRO/Wireless 3945ABG Network Connection
    Interface GUID: {16f026bc-d9fd-4a9d-9020-a32174a4bd6a}
    Local MAC Address: 00:1C:BF:68:1E:C5
    Network SSID: AP1
    BSS Type: Infrastructure
    Peer MAC Address: 64:A0:E7:29:08:E0
    Identity: host/PC2.mynet.lan
    User:
    Domain:
    Reason: Explicit Eap failure received
    Error: 0x40420110
    EAP Reason: 0x40420110
    EAP Root cause String: Network authentication failed due to a problem with the user account
    EAP Error: 0x40420110
    EVent ID 11004
    Wireless security stopped.
    Network Adapter: Intel(R) PRO/Wireless 3945ABG Network Connection
    Interface GUID: {16f026bc-d9fd-4a9d-9020-a32174a4bd6a}
    Local MAC Address: 00:1C:BF:68:1E:C5
    Network SSID: AP1
    BSS Type: Infrastructure
    Peer MAC Address: 64:A0:E7:29:08:E0
    Security Hint: The operation was successful.
    EVent ID 8004
    Wireless network is blocked due to connection failure.
    Network Adapter: Intel(R) PRO/Wireless 3945ABG Network Connection
    Interface GUID: {16f026bc-d9fd-4a9d-9020-a32174a4bd6a}
    Connection Mode: Automatic connection with a profile
    Profile Name: LAB1
    SSID(s): AP1
    BSS Type: Infrastructure
    Failure Reason:Explicit Eap failure received
    Length of block timer (minutes): 20
    EVent ID 8002
    WLAN AutoConfig service failed to connect to a wireless network.
    Network Adapter: Intel(R) PRO/Wireless 3945ABG Network Connection
    Interface GUID: {16f026bc-d9fd-4a9d-9020-a32174a4bd6a}
    Connection Mode: Automatic connection with a profile
    Profile Name: LAB1
    SSID: AP1
    BSS Type: Infrastructure
    Failure Reason:Explicit Eap failure received
    The peer MAC address is that of the Aironet access point:
    AP1#sh int
    BVI1 is up, line protocol is up
      Hardware is BVI, address is ccef.4807.35d2 (bia 64a0.e729.08e0)
      Internet address is 10.0.0.51/8
      MTU 1500 bytes, BW 54000 Kbit/sec, DLY 5000 usec,
         reliability 255/255, txload 1/255, rxload 1/255
      Encapsulation ARPA, loopback not set
      ARP type: ARPA, ARP Timeout 04:00:00
    [snip]
    Dot11Radio0 is up, line protocol is up
      Hardware is 802.11N 2.4GHz Radio, address is 64a0.e729.08e0 (bia 64a0.e729.08e0)
      MTU 1500 bytes, BW 54000 Kbit/sec, DLY 1000 usec,
         reliability 255/255, txload 1/255, rxload 1/255
      Encapsulation ARPA, loopback not set
      ARP type: ARPA, ARP Timeout 04:00:00
    [snip]
    Dot11Radio1 is administratively down, line protocol is down
      Hardware is 802.11N 5GHz Radio, address is 64a0.e72e.ba10 (bia 64a0.e72e.ba10)
      MTU 1500 bytes, BW 54000 Kbit/sec, DLY 1000 usec,
         reliability 255/255, txload 1/255, rxload 1/255
      Encapsulation ARPA, loopback not set
      ARP type: ARPA, ARP Timeout 04:00:00
    [snip]
    GigabitEthernet0 is up, line protocol is up
      Hardware is PowerPC405ex Ethernet, address is ccef.4807.35d2 (bia ccef.4807.35d2)
      MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
         reliability 255/255, txload 1/255, rxload 1/255
      Encapsulation ARPA, loopback not set
      Half-duplex, 100Mb/s, media type is T
      output flow-control is unsupported, input flow-control is unsupported
    Note: half-duplex because of the old hub I am using for my practice network. Plastic 5 port switch I had went bad.
    Note: yes, I am only using radio 0 for the time being.

    Looks like I'm at a dead end.
    But since it looks like the rest of the setup is fine, what I would like to do *now* is configure the Aironet to work with WPA2.
    WEP was only used for testing (well, if I can't make it work with WPA/2, what about WEP?)
    Since the WPA2 - EAP-TLS combination works just fine with the the Linksys, I have to conclude it's just a matter of entering the right commands on the Aironet to make this work.
    Yes, I'm almost ready to give up on the web-based GUI, it's closed on me twice when I click on "Apply" and it appears the configuration is not saved entirely (???).
    CLI via telnet seems both faster and more reliable but I don't know all the commands. Some of the documentation I've found assumes other situations, such as authentication with LEAP or use of a controller. Still looking...

  • How do you configure the server in this situation?????????????

    Hi,
    We have Oracle 10.2 and Windows 2003.
    We have Oracle on Cluster (with Windows software).
    When the System are without cluster all it’s OK!!!!!!
    We have 2 Resources Cluster Group: Oracle and Applications.
    We have Oracle in Oracle cluster group.
    We have “W” Drive and a ftp program in Application cluster group.
    We have C drive in both nodes. We have installed Oracle in both nodes but we have “W” drive only associate to the Active Node because is a Cluster resource (Application cluster group).
    All days we receive text files by ftp and we put it on W Drive. This text files are readen with external tables in Oracle.
    We have a problem when oracle fails and it goes to the another node (for ex. node2) because the external tables fail because the files are on Node1 on W Drive. If we move manually Applications cluster resource to Node2 then all it is OK.
    We think to put UNC pathes instead of “W” but it’s not possible (Metalink: Note:290703.1)
    How do you configure the server in this situation?????????????
    Thanks!

    We run a similar configurations and i doubt you have a chance other then reconfigure your setup. The way we do it is to have an ftp client in our database group and periodically transfer the files a second time (not elegant but it's working).
    If that's not an option you might be able to use unc names in your ftp server and set the ftp root to a directory hosted on a disk which is part of the database group.
    Or move to unix (that's what we do now). Than you don't have to bounce your server once in a month to apply security patches...

  • Wiki file attachments - can the wiki be configured to link to a file already on the server rather than uploading it into the page?

    Can the wiki be configured to link to a file already on the server rather than uploading it into the page? This would enable users to open (and edit) the original server hosted document rather than downloading a static copy that can't be edited and synced back into the wiki page.
    As a workaround I've tried attaching an alias to a file but it doesn't work - the wiki instead uploads the aliased file.
    From what I can work out, the default wiki behaviour is to upload a document to a wiki page, which creates a copy of the uploaded document in the wiki database. This copy has no connection to the original document. It can be downloaded and edited, but the edits are not saved back into the wiki hosted version of the document.
    I'd like to be able to upload a link or alias to a document (with preview please!) already on the server. A user could then preview the document or click to open and edit it.
    The only way I can do this at the moment is to create a link "afp://123.../doc.rtf" to the original. This is timeconsuming and confusing for non-technical users and doesn't offer the benefits of the attach function (ie document preview).
    Is there any way the wiki can be configured to link to documents already on the server using the attach functionality?

    An update for anyone in a similar situation.
    Patch 3944727 for 9.0.4.1 that solves this issue: "USER LOV IASM11SHIP EDIT USER LOV SHOULD SHOW THE NICKNAME ATTRIBUTE." However, the patch is mutually exclusive with the latest CPU's and there's no plan to merge the pacthes given the dwindling support for 9.0.4.1. So that patch is pretty much worthless.
    I've been told that this patch is included in newer portal versions, so the real solution is an upgrade.
    Trenton

  • How do you configure DHCP server on OSX Lion Server

    I want to use my Mac Mini Server as a DHCP server on my network.   I cannot find the place under Server to configure it.  
    Where would I find it?   It is not under Server.

    Hi
    Download the Server Admin Tools from here:
    http://support.apple.com/kb/DL1457
    These are not installed when installing Lion and then Server App. Once installed launch Server Admin, click on the Server's name in the side panel, click on Settings > Services and enable the DHCP Service. Once enabled it should appear in the side panel. The rest should be fairly obvious?
    HTH?
    Tony

  • The RADIUS request did not match any configured connection request policy (CRP)

    I setup NPS server and added a RADIUS Client access point, my project is to get a wireless user to authenticate using his/her AD credientials, my problem is i can't seem to authenticate my user
    my NPS server is giving me this error log under Event Viewer > Server Logs > Network Policy and Access Services
        Reason:                The RADIUS request did not match any configured connection request policy (CRP).
    but from my understanding i don't need to setup Connection Request Policies because i am using Network Policy
    Please Help!

    thanks for your reply, i setup a new NPS policy here is my error log
    Network Policy Server denied access to a user.
    Contact the Network Policy Server administrator for more information.
    User:
        Security ID:            NULL SID
        Account Name:            csdomain\rsingh
        Account Domain:            csdomain
        Fully Qualified Account Name:    csdomain\rsingh
    Client Machine:
        Security ID:            NULL SID
        Account Name:            -
        Fully Qualified Account Name:    -
        OS-Version:            -
        Called Station Identifier:        0026.992f.6761
        Calling Station Identifier:        2477.0392.b0f8
    NAS:
        NAS IPv4 Address:        192.50.2.2
        NAS IPv6 Address:        -
        NAS Identifier:            MYWAP
        NAS Port-Type:            Wireless - IEEE 802.11
        NAS Port:            35290
    RADIUS Client:
        Client Friendly Name:        MYWAP
        Client IP Address:            192.50.2.2
    Authentication Details:
        Connection Request Policy Name:    PEAP
        Network Policy Name:        -
        Authentication Provider:        Windows
        Authentication Server:        MYSERVER.csdomain.com
        Authentication Type:        EAP
        EAP Type:            -
        Account Session Identifier:        -
        Logging Results:            Accounting information was written to the local log file.
        Reason Code:            22
        Reason:                The client could not be authenticated  because the Extensible Authentication Protocol (EAP) Type cannot be processed by the server.

  • Error displaying host configuration

    I'm running version 10.2.0.1 of OEM on a Windows 2003 advanced server and I get
    the following error message when trying to view the charts for my cpu target: "Error displaying host configuration - Host Configuration"
    I also get the following error message:
    "Error getting data from the repository for target txsna09egssrv03.ITServices..... Exception: java.sql.SQLException: ORA-20206: ORA-06512: at "SYSMAN.EMD_MNTR_HOST", line 243 ORA-01403: no data found ORA-06512: at line 1"
    Any help with this would be greatly appreciated.
    Thanks

    I am also getting the same error, when i click host under general section of oem database control's homepage, but on the homepage itself, i have an alert under the secion RELATED ALERTS.
    That alert says "Memory Utilization is 99.77%" and when i click that, it is showing me the host configuration and i can monitor the host.
    why is the host link on the homepage gives an error whereas i can monitor the host through the related alerts.
    i have oracle 10g database server and have client running on rhel4.
    thanks!

  • Change RADIUS Certificate or Reset RADIUS, SERVER 3.2.2

    Hi All,
    I've got an expiring self signed certificate that I was using for the RADIUS service on 10.9, server 3.2.2.
    I can figure out how to replace this certificate with our valid trusted SSL certificate for our domain.  We originally setup the RADIUS server with the instructions at https://www.yesdevnull.net/2013/10/os-x-mavericks-server-setting-up-freeradius/
    If I just try to install new certs using sudo radiusconfig -installcerts command, it just breaks the radius.
    I've also tried blowing away the radius folder inside of /Library/Server in an attempt to reset RADIUS to the factor defaults, but after reinstalling the server app, and going through the process of setting up RADIUS, it's still using the old certificate.
    Any help would be appreciated!
    Thanks

    Thanks to Charles over at Krytped, deleting the Radius folder from /Library/Server/Radius and running this command:
    sudo rm /var/db/.ServerSetupDone
    Allowed me to get Server to recreate a clean Radius set.

  • 11g Grid Control - Host Configuration Collection Problems

    Hi Guys,
    I just installed Oracle 11g Grid Control and it has been running for 2 weeks until I recently tried to walk through the parts of it.
    My intention was to clear off all the error messages, critical warnings, alerts, and policy warnings.
    When I arrived at the development summary box, on the home tab, I can see that there is 1 collection problem.
    When I clicked it, I saw that apparently the problem is with the host where I installed the grid control.
    Problem type: Warning during collection of Oracle Software
    message: Unknown WLS Home Location or WLS Version in Middleware Home /u01/app/oracle/product/middleware
    I tried clicking on the "Refresh Host" button, but it didn't solve the problem at all.
    I have also tried to take a look at the targets.xml however it seems the configuration in there are already pointing to the correct path to the weblogic home.
    Please let me know if anyone has a suggestion for this.
    Searching from google doesn't really return anything closely matched to this.
    Thanks,
    Adhika

    What is the intent/timeline for fixing this bug? On MOS, it appears to have a status of "Status 33 - Suspended, Req'd Info not Avail". We are encountering this bug also and I would glady provide information from our systems in order for the issue to be resolved.
    Thanks.
    PostScript: FWIW, Google yielded a blog referencing this error and Doc ID 1433113.1. I am unable to access that document (as was the blogger). Because of this, and another major caveat (our machines with this collection error do not have WLS installed on them), I'm thinking this probably needs to be an SR rather than a forum discussion.
    Edited by: JeriF on Feb 4, 2013 12:00 PM

  • Frontend Host Configuring

    I have read the article on Middleware Magic on setting the front end host but when I hit the URL and observe it through httpWatch still shows the appserver/port as the "host".   Doesn't seem to matter what I put in there, it always returns the same thing in the host headers.  Questions:
    1) Is there another tool that shows the host headers and info coming back from the request?
    2) What format should I be filling this parameter in?   Should it have the entire URL in it (like http://sitportal1:7070/fc/Controller.jpf) or just a host name (like sitportal1).  The help doesn't seem to illustrate the format this needs to be input as.  I have tried it pointing the web server front end as well (sitweb2.company.com) but doesn't seem to return anything as the header but the name and port of the WebLogic app server.
    3) The application is deployed to a cluster and I've made the changes there as well, with the same results.   Yes, managed servers were restarted...
    I got points, who wants them?

    Do not know what you are trying to accomplish, but note that the front host setting makes it possible that a certain host name is configured to which redirects are sent (when it is set it rejects the information contained in the host header). It does not change the host header (not to my knowledge anyway).
    The documentation (3 Ensuring the Security of Your Production Environment) sheds some more light on this:
    "When a request on a web application is redirected to another location, the Host header contained in the request is used by default in the Location header of the response. Because the Host header can be spoofed — that is, corrupted to contain a different host name and other parameters — this behavior can be exploited to launch a redirection attack on a third party.
    To prevent the likelihood of this occurrence, set the FrontendHost attribute on either the WebserverMBean or ClusterMBean to specify the host to which all redirected URLs are sent. The host specified in the FrontendHost attribute will be used in the Location header of the response instead of the one contained in the original request."
    or (http://docs.oracle.com/middleware/1212/wls/WLMBR/mbeans/ClusterMBean.html?skipReload=true#FrontendHost)
    "FrontendHost - The name of the host to which all redirected URLs will be sent.
    Sets the HTTP FrontendHost for the default webserver (not virtual hosts) for all the servers in the cluster. Provides a method to ensure that the webapp will always have the correct HOST information, even when the request is coming through a firewall or a proxy. If this parameter is configured, the HOST header will be ignored and the information in this parameter will be used in its place, when constructing the absolute urls for redirects."
    What I understand from this is that you set a host name (for example, google.com, or some other host name that is mapped to an IP-address, or the IP-address itself)  to which the request is to be redirected (and if the application to which the redirect is going is not listening on any of the default HTTP ports (:80 or :443) you can define the port by using either frontend http port or frontend https port).
    As a tool to monitor HTTP(S) traffic you can probably use fiddler ( Fiddler - The Free Web Debugging Proxy by Telerik), but the one you are using (HttpWatch) is doing the job as well.

  • Host Configuration not found error in database control

    I have freshly installed Oracle DB 11g and a starter database.
    Then i went to emctl (database control), at the home tab, I noticed the status is up (Green up arrow icon) but the "Instance Name", "Version", "Up Until" entries have the value "unknown"
    And then when i Click on the "view all properties link", I noticed that the ORACLE_HOME entry has a warning icon after the entry. Then when you click on the ORACLE_HOME entry link, I get a page saying
    Host Configuration not found. Check to see if the target exists.Whats happening? Did I miss something in my installation?
    regards,
    Anton

    What is the OS?. Have you seen the Metalink note: 353681.1
    Subject: Problem: Click on ORACLE_HOME gets "Host Configuration not found. Check to see if the target exists"
    Doc ID: 353681.1 Type: PROBLEM
    Modified Date : 30-JUL-2007 Status: PUBLISHED

  • Re: All on One Host Configuration

    Evaluation mode runs on a single host. Please note that it is called evaluation mode because scale-able production deployments are NOT supported in evaluation mode.

    Hi,
    A small correction: There are two single host configurations for VDI ("All on One Host" and "VDI Demo").
    * All on One Host - http://wikis.sun.com/display/VDI3/Supported+Configurations#SupportedConfigurations-AllonOneHost
    * VDI Demo - http://wikis.sun.com/display/VDI3/Getting+Started+-VDIDemo
    The VDI Demo is not a supported production environment configuration, but the "All on One Host" configuration is fully supported as long as you have an extra support contract with MySQL to cover the InnoDB engine.
    Best regards,
    Stephanie

Maybe you are looking for