Radius Authorization failure
I have defined Radius proxy on csg2 to external radius server, but pdp fails with Authorization failure message on GGSN and on Csg2 debut log I see “SAMI 3/3: Nov 23 15:11:43.937: RADIUS: Dropping the unsolicited RADIUS packet”
IAS server might be incorrect Radius Attribute to the router.ou can find an example of the RADIUS attributes required at the end of
'Configuring Authentication Proxy' at http://www.cisco.com/en/US/products/ps6350/products_configuration_guide_chapter09186a00804ad9bc.html#wp1002138
Similar Messages
-
AP Cannot join WLC, i have RADIUS authorization is pending for the AP Error
Hi Support,
I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0
I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 124
- Successful discovery responses sent...................... 124
- Unsuccessful discovery request processing................ 0
- Reason for last unsuccessful discovery attempt........... Not applicable
- Time at last successful discovery attempt................ Jun 11 11:56:46.133
- Time at last unsuccessful discovery attempt.............. Not applicable
Join phase statistics
- Join requests received................................... 62
- Successful join responses sent........................... 0
- Unsuccessful join request processing..................... 62
- Reason for last unsuccessful join attempt................ RADIUS authorization is pending for the AP
- Time at last successful join attempt..................... Not applicable
- Time at last unsuccessful join attempt................... Jun 11 11:56:56.606
Another this is from AP cli, i cannot have the command configure terminal
Can you please help meThanks Scott, i'm in Gabon (Central Africa) there is no Gabon in coutries list, then i chosen France.
this is the new status
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 126
- Successful discovery responses sent...................... 126
- Unsuccessful discovery request processing................ 0
- Reason for last unsuccessful discovery attempt........... Not applicable
- Time at last successful discovery attempt................ Jun 11 13:38:37.411
- Time at last unsuccessful discovery attempt.............. Not applicable
Join phase statistics
- Join requests received................................... 63
- Successful join responses sent........................... 1
- Unsuccessful join request processing..................... 62
- Reason for last unsuccessful join attempt................ RADIUS authorization is pending for the AP
- Time at last successful join attempt..................... Jun 11 13:38:49.888
- Time at last unsuccessful join attempt................... Jun 11 11:56:56.606
Configuration phase statistics
--More-- or (q)uit
- Configuration requests received.......................... 0
- Successful configuration responses sent.................. 0
- Unsuccessful configuration request processing............ 0
- Reason for last unsuccessful configuration attempt....... Not applicable
- Time at last successful configuration attempt............ Not applicable
- Time at last unsuccessful configuration attempt.......... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure............... Not applicable
Last AP disconnect details
- Reason for last AP connection failure.................... Timed out while waiting for ECHO repsonse from the AP
- Last AP disconnect reason................................ Not applicable
Last join error summary
- Type of error that occurred last......................... AP got or has been disconnected
- Reason for error that occurred last...................... Timed out while waiting for ECHO repsonse from the AP
- Time at which the last join error occurred............... Jun 11 13:40:31.432
AP disconnect details
- Reason for last AP connection failure.................... Timed out while waiting for ECHO repsonse from the AP
Ethernet Mac : 00:06:f6:d6:03:f0 Ip Address : 172.25.100.84
--More-- or (q)uit
(Cisco Controller) > -
910 application authorization failure blackberry
hi all im new to here and looking for some help i have just got a sceond hand bb and it dint have appworld on it so when i tryed to download it it came up with this 910 application authorization failure and am not sure y can anybody help me out thanks
leeHello leewilliam88
Welcome to the Community
From the Error message it seems that an IT policy has been enabled on the Device.As you had brought it second hand to resolve the problem you had to remove the IT policy from the device .So to do that follow this Knowledge Base :
KB14202 : How to remove an IT policy from a BlackBerry Device.
Try any of the Method suggested in Knowledge Base to remove the IT policy from the device.Additional Information regarding the error :KB12230
I hope it will Resolve your problem.
Prince
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it. -
"Create PDF from Web Page" Yields Authorization Failure
Acrobat 9 Pro Extended running on Windows XP Service Pack 3:
When using "Create PDF from Web Page," certain linked pages result in an "Authorization Failure" error message. Is there any way to instruct Acrobat to disregard pages that are not downloadable and continue creating the PDF?I am having the same issue AND none of my pages or files require a UserID or Password. My issue appears to be something with the domain because a and b work just fine and produce a PDF file while item c does not work and produces the error msg.
http://www.dot.wi.gov/projects/neregion/151/index.htm works just fine and produces a PDF file.
http://www.dot.state.wi.us/projects/neregion/151/index.htm works just fine and produces a PDF file.
http://www.wisconsindot.gov/projects/neregion/151/index.htm produces an error msg. ‘Nothing done’.Error info. - Authorization Failure http://www.wisconsindot.gov/projects/neregion/151/index.htm
[email protected] -
Create PDF From Web Page - Authenticated SharePoint Sites generate "Authorization Failure" error
We have several authenticated sharepoint sites on our intranet, and we are trying to create a PDF of a site (x levels down) using the Acrobat create PDF from web page feature. When you try to create a PDF from a non-sharepoint, authenticated website, a login prompt appears asking for login credentials. However, when you try to use the same feature on an authenticated sharepoint site, you do not get prompted for credentials and instead get an Authorization Failure error. the popup says "Error: Nothing Done". We have successfully PDF'd anonymous sharepoint sites on the WWW. Has anyone successfully PDF'd an authenticated SharePoint site?
Thanks in advance,
-Richard.I am having the same issue AND none of my pages or files require a UserID or Password. My issue appears to be something with the domain because a and b work just fine and produce a PDF file while item c does not work and produces the error msg.
http://www.dot.wi.gov/projects/neregion/151/index.htm works just fine and produces a PDF file.
http://www.dot.state.wi.us/projects/neregion/151/index.htm works just fine and produces a PDF file.
http://www.wisconsindot.gov/projects/neregion/151/index.htm produces an error msg. ‘Nothing done’.Error info. - Authorization Failure http://www.wisconsindot.gov/projects/neregion/151/index.htm
[email protected] -
Can you configure Radius authorization to access a router or not.
I am confused because the Practical Studies book says "Use the local database for authorization instead of RADIUS because is incapable of understanding CLI":
aaa new-model
aaa authentication login default group radius
aaa authorization default local
Now in the Cisco website, says you can after configuring the following:
Cisco Secure NT RADIUS
Follow these steps to configure the server. http://www.cisco.com/en/US/tech/tk59/technologies_tech_note09186a008009465c.shtml
IETF, Service-type (attribute 6) = Nas-Prompt
In the CiscoRADIUS area, check AV-Pair, and in the rectangular box underneath, enter shell:priv-lvl=7.
aaa new-model
aaa authentication login default tacacs+|radius local
aaa authorization exec tacacs+|radius local
username backup privilege xxx password xxxx
radius-server host 171.x.x.x
radius-server key xxxx
privilege configure level 7 snmp-server host
privilege configure level 7 snmp-server enable
privilege configure level 7 snmp-server
privilege exec level 7 ping
privilege exec level 7 configure terminal
privilege exec level 7 configureYou can specify the exec privelege level for certain user on specific AAA client using RADIUS.
Based on that certain user can run all the commands that are part of that particular Privelege exec level.
Now if you want to allow certain set of commands from particular privilege exec level you need to use tacacs+ protocol
and enable command authorization sets command on your AAA server.
Check the following links as references on command authorization:
http://www.cisco.com/en/US/partner/products/ps9911/products_configuration_example09186a0080bc8514.shtml
http://www.cisco.com/en/US/partner/products/sw/secursw/ps2086/products_configuration_example09186a00808d9138.shtml
Please make sure to rate correct answers -
How to configure CCMS alert to monitor Authorization failures?
Dear All,
How to configure CCMS alert to monitor Authorization failures?
Thanks
AshokHello,
in case you have not yet set up your monitoring infrastructure, the following link will provide you with the information needed:
http://service.sap.com/monitoring
If everything is set up (Agents are installed and connected to your central monitoring system, ...) you can go to transaction RZ21, select Technical Infrastructure - Configure Central System - Assign Central Autoreactions to set up your alerts.
For the Update errors use the MTE CLass AbapErrorInUpdate. For the Lock please use the search Option.
Regards
Christian
Edited by: Christian Rose on Apr 25, 2011 7:59 PM -
ISE RADIUS authorization NX-OS
Anybody could confirm if RADIUS authorization is not supported on NX-OS?
If it's not supported, how should it be configured with ISE once ISE doesn't support TACACS?
NX-OS(config)# aaa authorization config-commands default group radius local
Radius group is not supported for command authorization
could not update aaa configurationJan is correct, you can't configure NX-OS based device the same way you would IOS based one when it comes to AAA. NX-OS devices do not "understand" privilege level. Instead, they use RBAC (Role Based Access Control). As a result, you have to return a shell role from your Radius server:
shell:roles=user_role
For more info take a look at the latest "NX-OS Security Configuration Guide" or this link:
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/6_x/nx-os/security/configuration/guide/b_Cisco_Nexus_7000_NX-OS_Security_Configuration_Guide__Release_6-x/b_Cisco_Nexus_7000_NX-OS_Security_Configuration_Guide__Release_6-x_chapter_0110.html#task_1074483
Hope this helps!
Thank you for rating helpful posts! -
Authorization Failure Redirect URL in OAM
Hi,
From OAM policies i want to redirect a user to Authorization Failure page by configuring redirect URL for Authorization Failure. But user is always redirected to OAM operation error page (with an error message that URL .. has been denied for the user) in case of Authorization Failure..How to redirect the user to my AuthFail.html page ? I am able to redirect the user to AuthenticationFailure page incase of authentication failure..but not able to redirect in case of authorization failure..how to achieve this?
Thanks & Regards,
SrikanthHi,
I am new to OAM and facing the same error in Authz Rule. Did your issue get resolved?
When I tested the URL with access tester for authz failure scenario, I got Authorized Inconclusive.
I do understand if I mention the AuthFail.html in the redirection URL Authz Inconclusive, the user would be able to see the appropriate error page. But I wanted to understand the reason for authz getting into inconclusive condition. Can someone provide me clarity on this?
Thanks! -
ACS + Device Authorization Failure
Good Afternoon:
I hoping someone can help me out... I have an ACS configured with a group that is setup for admins. This group is mapped to an AD group. This is setup correctly. On each network device are the commands:
aaa authorization exec default group tacacs+ if-authenticated
I can create a local user and place them into the aformentioned group and the TACACs authentication and authorization work fine. However, I cannot use that same local group mapped to a AD group and a user in that group. It passes authentication but I get an authorization failure in my logs (ACS) and a authorization failed message on the device.
Any ideas?
Thanks!ACS has extensive logging capabilities that allow an administrator to troubleshoot any issue pertaining to the ACS server itself (for example, replication) or an AAA request problem (for example, an authentication problem) from NAS.
Refer the following url for more info on troubleshooting ACS:
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.1/user/A_Trble.html -
Radius authorization for WAAS CM GUI
Hi,
We would like to enable radius authorization to the WAAS Central Manager GUI. We are having some problems doing this. Also this is only documented for TACACS and not for Radius.
We've seen the waas_rbac_groups attribute that can be delivered via Tacacs, can this attribute also travel in the radius attributes? We've already tried: shell:waas_rbac_groups on a Cisco-AV-Pair but that doesn't do it.
There should be a way; knowning that the TACACS is very rare these days.
Please help us
Regards,
ErikHi Prabnu,
Google Chrome has the same strange behaviour.;-( See the attachment.
Roman -
RME 4.1.1 - PSIRT and EoS/EoL reports authorization failure
Hello group,
I have RME 4.1.1 installed and I am attempting to generate either a PSIRT or an End Of Sale/End Of Life report. I start the report from RME->Reports->Report Generator and input all the appropriate information (CCO user/pass, email, etc) and then click "Finish". I get the popup that says to get Report Jobs for the status of the report, and as fast as I can navigate to Report Jobs I see that the job failed.
So I check invreports.log and this line stands out in particular:
[ Fri Oct 01 13:45:38 CDT 2010 ],ERROR,[main],com.cisco.nm.rmeng.inventory.reports.job.JobExecutor,runReport,773,Authorization failure for ajschroedercom.cisco.nm.rmeng.util.NotAuthorizedUserException: ajschroeder
I do have my Ciscoworks server integrated with ACS, so I reregistered my apps with ACS, and restarted ACS and Daemon Manager with no luck, I even applied the patch described in the following doc: https://supportforums.cisco.com/docs/DOC-9080
I am confident that I am missing something, but I have no idea what. I have attached my invreports.log
As always, any help would greatly be appreciated,
AJ SchroederThis is CSCsm77700 which is fixed in RME 4.2. I highly recommend you download the upgrade to LMS 3.2 from http://www.cisco.com/go/nmsevals . However, a patch is available for RME 4.1.1 if you contact TAC.
http://wwwin.cisco.com/ios/cets/pdi/cbms/cdets/legend.shtml -
My tablet got authorization failure when I want to open book
the book that i downloaded on bookshop opened on my PC,but shows authorization failure on my tablet.what to do?
Hi Zannat,
Don't get scared. Cookies are the small file which stores your settings for a website, such as location details, login details, language details and so..
Some sites don't care about your cookies settings but some other sites instructs you to enable cookies in your browser. Enabling cookies is too easy.
Just follow the instructions which explained [[Enable and disable cookies that websites use to track your preferences |here]] .
Thank you!!! -
SMS through Midlet -- Authorization Failure
Hi,
I have written a small Midlet that sends an SMS. When I run the MIDlet in Wireless Tool Kit , I am getting "OTA Error Code (49) - Application authorization failure. [javax.microedition.io.Connector.sms]".
I have added the permission for "javax.microedition.io.Connector.sms". I don't know what's else to do.
Could some please help!!!
Thanks,
AnujaHi,
I have written a small Midlet that sends an SMS. When I run the MIDlet in Wireless Tool Kit , I am getting "OTA Error Code (49) - Application authorization failure. [javax.microedition.io.Connector.sms]".
I have added the permission for "javax.microedition.io.Connector.sms". I don't know what's else to do.
Could some please help!!!
Thanks,
mitesh -
RAC -- CRS-0254: authorization failure
Hi,
i m trying to start 1 instance in rac env using srvctl command i m getting following error.
CRS-0254: authorization failureHi Pawell,
I am not sure whether your problem has been resolved or not.
But unfortunately even we are facing the same issue. Till today morning everything was fine. Suddenly users started complaining that they can't connect to the database.
When we tried log into database using sqlplus command it gave us TNS:protocol Adapter error which is weird. (every service relates to oracle and cluster are running from windows services and even when we checked crs_stat -t ==> all the services are up and running)
and when we tried to stop the services on the cluster level it gave us CRS-254 which is authorization failure.
Though restarting the server fixed the problem as of at this moment, We don't really know what caused that problem.
If your problem has been resolved can you give me some information in relates to this.
Regards
Balaji
Maybe you are looking for
-
My blends in Illustrator CS4 are not saving or printing correctly. Why?
Why are my blends in Illustrator CS4 not saving or printing correctly??? SPECS: Adobe CS4 MAC 10.5.8 I got a outlined Text blend with a drop shadow. And another text with a drop shadow on top. Not too complex at all. Heres some screenshots of the p
-
Hi, I'm having a problem in a VM Guest cluster using Windows Server 2012 R2 and virtual disk sharing enabled. It's a SQL 2012 cluster, which has around 10 vhdx disks shared this way. all the VHDX files are inside LUNs on a SAN. These LUNs are presen
-
With Photoshop elements you can cut a person or object out - can Aperture 3 do the same?
Looking to purchase Aperture 3 but wanted to know if it can do similar things to Photoshop elements. Photoshop elements allows you to cut/remove objects, people, faces, etc...I would like to know if Aperture can do the same? Are there any other featu
-
Custom Policy vs. J2EE Security
Hi there, Java Security architecture gurus, I am currently trying to find the best architecture for the new security framework for our company's application. The system requires instance based security. ACLs are stored in a database. JAAS's authentic
-
Problems accessing ejb 3.0 entity bean from project
I have written some code using ejb 3.0 and was previously accessing the entity bean without problem when both ejbs and the accessing code were in the same project. However I have moved the accessing code into a different project within the same appli