Radius local server and wireless access points

Hello to all,
I would like to ask a question related to radius server. I have a Allied telesis core switch and i configure the radius server locally, also i configure the port1.0.7 for dot1x and i am using dynamic vlan. If i connect my laptop to port 1.0.7 i can get the correct ip from the dhcp server. If i connect an access point to the same port , how i should configure the dot1x ? for multiple hosts? I know i am using allied telessis but the config is very similar to the cisco: take a look:
(Radius and nas config)
radius-server host 127.0.0.1 key awplus-local-radius-server
aaa authentication dot1x default group radius
aaa authentication auth-web default group radius
crypto pki trustpoint local
crypto pki enroll local
radius-server local
server enable
nas 127.0.0.1 key awplus-local-radius-server
group Andrew
attribute NAS-Identifier andrew
attribute Tunnel-Medium-Type IEEE-802
attribute Tunnel-Private-Group-Id 10
attribute Tunnel-Type VLAN
user andrew encrypted password wh8q0J2oYSn0y4cynksNCqfbaUtRGv/E6JaJrW+s3Zs= group Andrew
(port config)
interface port1.0.7
switchport
switchport mode access
auth-web enable
dot1x port-control auto
auth host-mode multi-supplicant
auth dynamic-vlan-creation
I tried with auth-web and without but no luck. If someone have a sample config how to configure the dot1x to be able to use access point please paste it.
Thanks
Andrew

I'm not sure if the Autonomous APs have the option for AAA Override. On the WLC, I can go into the BSSID, Security, Advanced, and there's a checkbox that I would check to allow a Radius server to send back the VLAN.
I did a little research and it looks like the 1300 may give this option but instead is defined as "VLAN Override". I've found the release notes for 12.3(7)JA5 (not sure what version you're running) that give mention and a link to configuring EAP on page 4: http://www.ciscosystems.ch/en/US/docs/wireless/access_point/1300/release/notes/o37ja5rn.pdf
Hope this helps

Similar Messages

Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points

Hi Guys,
I would like to go for "Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points 1300". I want the AP to broadcast only 1 SSID. The client find the SSID ->put in his user credential->Raudius athentication->assign him to an specific vlan based on his groupship.
The problem here is that I don't have a AP controller but only configurable Aironet Access Points 1300. I can connect to the radius server, but I am not sure how to confirgure the AP's port, radio port, vlan and SSID.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
I go through some references:
3.5 RADIUS-Based VLAN Access Control
As discussed earlier, each SSID is mapped to a default VLAN-ID on the wired side. The IT administrator may wish to impose back end (such as RADIUS)-based VLAN access control using 802.1X or MAC address authentication mechanisms. For example, if the WLAN is set up such that all VLANs use 802.1X and similar encryption mechanisms for WLAN user access, then a user can "hop" from one VLAN to another by simply changing the SSID and successfully authenticating to the access point (using 802.1X). This may not be preferred if the WLAN user is confined to a particular VLAN.
There are two different ways to implement RADIUS-based VLAN access control features:
1. RADIUS-based SSID access control: Upon successful 802.1X or MAC address authentication, the RADIUS server passes back the allowed SSID list for the WLAN user to the access point or bridge. If the user used an SSID on the allowed SSID list, then the user is allowed to associate to the WLAN. Otherwise, the user is disassociated from the access point or bridge.
2. RADIUS-based VLAN assignment: Upon successful 802.1X or MAC address authentication, the RADIUS server assigns the user to a predetermined VLAN-ID on the wired side. The SSID used for WLAN access doesn't matter because the user is always assigned to this predetermined VLAN-ID.
extract from: Wireless Virtual LAN Deployment Guide
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00801444a1.html
==============================================================
Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller Configuration Example
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
==============================================================
Controller: Wireless Domain Services Configuration
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c951f.shtml
Any help on this issue is appreicated.
Thanks.

I'm not sure if the Autonomous APs have the option for AAA Override. On the WLC, I can go into the BSSID, Security, Advanced, and there's a checkbox that I would check to allow a Radius server to send back the VLAN.
I did a little research and it looks like the 1300 may give this option but instead is defined as "VLAN Override". I've found the release notes for 12.3(7)JA5 (not sure what version you're running) that give mention and a link to configuring EAP on page 4: http://www.ciscosystems.ch/en/US/docs/wireless/access_point/1300/release/notes/o37ja5rn.pdf
Hope this helps

Westell 327w and Wireless Access Point

I had DSL last year, but have since changed to FIOS, which I love. So I have the Westell 327W modem/router that isn't being used. I have decided to use it in another project for the 4 port ethernet and the wireless capability.
As this other project, we are using another service, which isn't DSL. However, I figured that I could use the 327w as the wireless access point. I currently have access to the internet through the provided internet service and from there I go into a Cisco ASA 5505 firewall. From there I run an ethernet cable to the 327w.
As long as I plug a computer into one of the 4 ethernet ports on the 327w, I'm able to ping to the Internet using either the IP address or using DNS. I'm able to surf and everything.
I have also set up the wireless and using WPA security and I'm able to connect a laptop to the wireless. I get the IP address via DHCP from the ASA, so I have turned off the DHCP server on the 327. I have also turned off the firewall. I then test connectivity and I can ping anything on the network that is assigned by the ASA, but when I try to ping to an Internet address, by the address, I get request timed out. I also don't get anything back on DNS and so forth.
What do I need to do on the 327 to allow the wireless to work with the current connection set up.
Thanks for the help and information.

I got it to work. What I had to do was to set up the 327w in VLAN mode so that the wireless side would send the packets out the ethernet port to the ASA or another router.
In fact, I'm writing this on the wireless setting of the 327w. So setting the VLAN allow the wireless to send and receive packets.

How to move all my data to a server and wirelessly access it from any Mac

Hi. I have a PB, an MBP, a Mac Mini and a new iMac, which all serve different purposes. I have got to the point at home where I want to have one private account with all my data on a HD and to just log in to it from whichever machine I happen to be using. I currently have an Airport Express as my wireless router and am considering buying and Airport Extreme/Time Capsule. I have about 500GB of data, which is growing pretty quickly since I have use of an HD camcorder, so I will buy one or two large drives in addition to the various external HDs I already (that total about 850GB) have. What is the best way (at relatively low cost) for me to set up my wireless home network in order to achieve the above goal?
Thanks for your time.
Matthew Whiting

Don't go there. At least not for all your data.
The relatively low throughput and high latency of the wireless connection (at least compared to direct-attached disks) will make accessing large files cumbersome and frustrating. Since you specifically mention HD video you should be aware that what takes a long time now will take a lot longer if the media is accessed over the wireless network.
So while your goal might be technically feasible, it's unlikely to be workable.
Instead you should consider focussing your centralized data on content that makes sense (e.g. maybe your iTunes library), and store data locally where it's more appropriate (e.g. consider one machine for video editing).
Therefore you need to analyze your data - both in terms of content (what you have) and use (how you access it) to determine what makes sense to store centrally. Once you have that it will be easier to form a plan.

Setting up WRVS4400N for switch & wireless access point

Howdy, first post here. What is the proper way to configure this device to act as a switch and wireless access point so I can connect it to a switch with router upstream? I have a DLink router that was easy: disable UPnP, disable DHCP, set an IP/Subnet, and it worked.
My main router has a subnet mask of 255.255.240.0 but in the WRVS4400N setup screen I only get a list box with a limited number of masks, all of which are 255.255.255.x. Is there any way to specify the 240?

No. You cannot use a subnet mask larger then 255.255.255.0 on Linksys routers. They are only built to handle 255.255.255.0 and smaller. I guess they consider a LAN which requires a larger subnet, i.e. expects to run more then 253 networked devices requires a larger router.
The only thing you can do is to choose 255.255.255.0 and to pick an IP address which matches the IP address from which you expect to do the usual configuration work. If you use 10.0.0.0/255.255.240.0 but the computers which have to configure the router are all in 10.0.1.0/255.255.255.0 you can use that subnet. This works with computers even if they have a different subnet mask.
Of course, you can set any IP address you want, even one completely outside your normal LAN in order to "hide" the web interface from the normal LAN operation. The IP address of the router in your setup is irrelevant for the switching and wireless access. Both operate on ethernet/MAC addresses and the IP address of the router does not play any role there. If you use the 10 subnet mentioned before you could as well leave the router at 192.168.1.1/255.255.255.0. Whenever you have to access the web interface of the router you must temporarily set a static IP address inside 192.168.1.* on the computer...

Debug radius local-server

Hi all!
Please help me/
I'm use c181x-adventerprisek9-mz.151-4.M9.bin.
I'm set AP with local radius server. In official documentation have "debug radius local-server", in ios command reference this command also exits.
But in my router not have this command.
This is bug?

Are you running this command in Privileged EXEC mode, or global config mode? This is a Privileged EXEC command, so when you enter it, your prompt should look like this:
RouterName# debug radius local-server
And not like this:
RouterName(config)# debug radius local-server
Please also note that since this is a debug command, it will not appear in your device's running-config, and it may not continue running if you reload or power-cycle your device. It will just show debug messages at the console line and/or log them to the logging buffer and/or to an Syslog server, if configured.

Can an iMac serve as a wireless access point server?

I have a current iMac with standard built in wireless capability but I'm on the net with wires (RJ45 twisted pair ethernet CAT5 cables). Can my iMac serve as a wireless access point for a new device in the house (Nintendo Wii)? Is there a setting I can turn on, or software that can be downloaded to have the iMac act as a server instead of just a client on a wireless network? I know that it's best to have dedicated hardware do this, but I'm looking for a software solution to use while I decide what to buy.
Currently I have a DSL connection and a star style home network. The DSL modem has an ethernet cable to a hub, and our 2 macs connect with wires to the hub. (I have an older DSL modem that has no wireless capability, I know that upgrading the DSL connection involves a new modem that includes wireless, but the phone company makes no guarantees about supporting Macs, so I have to do some research first.)
-Ken

If your iMac connects to internet from ethernet cable, you can use airport to share the connection wirelessly by creating a network from airport, then go to system preference > sharing > internet and enable internet sharing. But if you already have a wireless router, Mac should be compatible, there is nothing inherently different between iMac's airport and PC's wireless card.
For Wii, I have no experience myself but there are plenty of posts on this forum, like this one: http://discussions.apple.com/thread.jspa?messageID=4528652&#4528652
(linked to http://www.virtualmatt.com/?p=7)

AAA configuration and Linksys Wireless Access Point

Hi,
Can we authenticate Linksys Wireless Access Point thru ACS TACACS+ or RADIUS ? If yes , please tell me the config steps.
Thnaks .
Anil K.

Hi,
Can we authenticate Linksys Wireless Access Point thru ACS TACACS+ or RADIUS ? If yes , please tell me the config steps.
Thnaks .
Anil K.
Check out the below link for Linksys with Radius server authentication:-
http://forevergeeks.com/setup-linksys-router-with-radius-server-authentication-2
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

Apple TV 2G (Airplay and Homesharing) can only stream from devices on the same wireless access point range??

connection:
40 Mbps Fiber Broadband connection using:
Devices:
1. Main Modem/router (AP1): Huawei HG8245 (provided by ISP) - Wireless enabled.
2. Remote Access point (AP2): Linksys/Cisco E3200 Wireless gigabyte router flashed with DD-WRT v24-sp2 (06/14/11) mini (Cascaded -wired- LAN to LAN from main modem).
3. Wireless Repeater to cover a dead spot (AP3): Linksys/Cisco E1000 wireless repeater.
4. Apple Tv (AT2G) with home sharing/airplay enabled.
5.( Ipad) with home sharing on itunes enabled.
6. Win7 (PC) using iTunes with Home sharing enabled.
all devices are updated to their latest firmware.
In order to cover a large 3 story house with Wifi. I had (AP1) is located on the first floor, while (AP2) is located in the basement floor directly wired by LAN to LAN with (AP1). (AP3) is located on the Ground floor away from the living room to repeat wireless network into the back yard. While (AT2G) is located in the living room on the ground floor right in the middle of both (AP1) + (AP2) while connected via Wifi.
Network SSID, security, passphrase and wireless settings of (AP2) are identical to (AP1) to create a single big LAN/WLAN roaming network where all devices connected to both wireless access points can find/share the others. As understood, it's refered to as bridging.
I have noticed that my iphone/ipad does not show the airplay button anywhere within the wireless network. it seems that the apple TV randomly choses to connect to the AP with stronger signal, or switch to the other in case of a reboot to one of them.
to elaborate further, if i was sitting in the living room (groundfloor), trying to airplay some you tube contents via Wifi to my Apple TV, i may not find the airplay button available all the time, i found out the reason is while i'm wirelessly connected to AP1, the Apple TV was connected to AP2 and both deviced cannot detect each others to enable my purpose. that goes the same for Home Sharing. only if my Ipad/PC and Apple Tv are on the same wireless AP. they would detect each others immediately.
although, the second AP (AP2) is suppose to extend my wireless network of the same subnet in which any device connected can be found.
After all sorts of trial and error tweaking my router/access point, I thought the problem would be due to the Linksys 3200 capability of bridging WLAN and lacks few protocols that enables my purpose. i have flashed the firmware to a DD-WRT, but again, problem was not solved.
I have not tried having my Apple Tv wired to either router/AP, but i assume it may work well if i do so. i still need to solve this wireless connection issue though.
Am i the only one with this problem, would there be something wrong with my setup?
Your feedback is highly appreciated.

You may or may not already have your network set up correctly, it's just that I can't tell from what you have said.
I have a main router provided by my ISP, I have several other Airport Extremes and Airport expresses connected by Ethernet, all set up to bridge the network created by the main router.
Each maker has their own settings, but bridging should be reasonably obvious. In simple terms my main router distributes IP addresses to all devices, the Airports bridge that network by passing these addresses to the devices from the main router. A base station that isn't in bridging mode will distribute its own addresses to the devices connected to it.
I don't really follow your next point.
instruction for configuration vary from manufacturer to manufacturer, the best course of action here is to refer to the manual. If everything is set up properly the addresses of everything on your network will have identical sets of numbers for the first 3 of 4 groups of numbers that make up an address, the last set must always be different. I think the part you are referring to with your DD-WRT is the option to have Ethernet and wifi bridged or not.
Some routers may be easier to configure than others, but generally speaking they should all work with the Apple TV. 5Ghz is less likely to suffer interference but it is much more likely to be blocked by solid objects, it may or may not be an advantage.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

Can I disable my Verizon Fios Router Wireless radio, connect it to a switch and use my airport express as my wireless access point connected to an in wall ethernet port?

Here's the deal. I have a Verizon Fios MI424WR router. My house has CAT5 throughout the house. The media panel is located in the garage. I want to take the Verizon Fios Router and cannot it in the media panel so I can connect a switch to it, that way, all my CAT5 can fire throughout the house. Verizon being Verizon decided to connect the router directly in the office.
Can I go this route (Router in media panel, switch cross connect to it) and use Airport Express, connected to one of the in-wall CAT5 ports in my house and then set it up as my wireless access point to provide wifi to my portable devices (iPad, iPhone, Macbook)? Is this possible? Will Airport Express comminicate with my verizon router via ethernet in-wall? Do I have to turn off the wireless radio in the Verizon router? Any help would be greatly appreciated!

That is right, by hard wired I was just making clear wired vs wireless attachment. AirPort family of devices will only act in a repeater mode with their own family members, not FiOS routers. they have to be wired to work.
There are some useful docs you can download from Apple, Support, Manuals, Peripherals, AirPort (just follow thos links from the Support button on the top bar):
Apple AirPort Networks
Designing AirPort Networks
AirPort Express Setup Guide
The last has a diagram of what you are trying to do, though without the house wiring, etc., but the basic principle.

Forgetting WiFi password, and not connecting to wireless access point automatically??

I'm using (until tomorrow when I get a MacBook Pro which HOPEFULLY won't have the same problem) a pre 2007 Macbook which is running Mac OS X 10.5.8. It was previously owned by my brother and passed onto me about 4 months ago. Within that time I've had nothing but problems with the WiFi connection!
The first issue would have to be that if I put the MacBook to "sleep" rather than turning off, it disconnects from WiFi during that process. Fine, that's to be expected. But when I wake it up, it's not only disconnected, but I have to re-enter my WiFi password in order to reconnect. Is there some reason that it will not remember the password through this sleep process? Turning off and on normally works fine, and it connects automatically, but not when it sleeps.
The second problem is equally confusing to my mind. In my house, we have a wireless access point upstairs (we have 3 floors after having our attic converted). All characteristics (name, password etc) are the same on the access point as on the main router downstairs. Every device in our house, included a couple of android phones, a tablet, and two laptops running various versions of Windows, all connect to this wireless access point with no problem at all. None of them have been "set up" to do so, in that they detect it as part of the same network and join it automatically. But for some reason, my MacBook won't do it? At first I would assume that perhaps it's due to the age of my MacBook and maybe some flaw in the old operation system, but my iPhone 4S running iOS 7 doesn't connect to this access point either. Is this some weird security thing that Apple use in their devices??
To make things even more frustrating, the MacBook's issue of remembering the WiFi password means that when I come back downstairs and into range of the main router, it's forgotten the password again and I have to re-enter it to reconnect.
Can some PLEASE offer some kind of assistance? I'm getting a brand new MacBook Pro tomorrow and if it's an OS issue then I assume I won't have it anymore, but I'm desperate to solve this issue one way or another considering this machine will be staying in the family and in this house so will pressumably have the same issues.
Thanks in advance guys! If I've not given enough info, just ask

I'm using (until tomorrow when I get a MacBook Pro which HOPEFULLY won't have the same problem) a pre 2007 Macbook which is running Mac OS X 10.5.8. It was previously owned by my brother and passed onto me about 4 months ago. Within that time I've had nothing but problems with the WiFi connection!
The first issue would have to be that if I put the MacBook to "sleep" rather than turning off, it disconnects from WiFi during that process. Fine, that's to be expected. But when I wake it up, it's not only disconnected, but I have to re-enter my WiFi password in order to reconnect. Is there some reason that it will not remember the password through this sleep process? Turning off and on normally works fine, and it connects automatically, but not when it sleeps.
The second problem is equally confusing to my mind. In my house, we have a wireless access point upstairs (we have 3 floors after having our attic converted). All characteristics (name, password etc) are the same on the access point as on the main router downstairs. Every device in our house, included a couple of android phones, a tablet, and two laptops running various versions of Windows, all connect to this wireless access point with no problem at all. None of them have been "set up" to do so, in that they detect it as part of the same network and join it automatically. But for some reason, my MacBook won't do it? At first I would assume that perhaps it's due to the age of my MacBook and maybe some flaw in the old operation system, but my iPhone 4S running iOS 7 doesn't connect to this access point either. Is this some weird security thing that Apple use in their devices??
To make things even more frustrating, the MacBook's issue of remembering the WiFi password means that when I come back downstairs and into range of the main router, it's forgotten the password again and I have to re-enter it to reconnect.
Can some PLEASE offer some kind of assistance? I'm getting a brand new MacBook Pro tomorrow and if it's an OS issue then I assume I won't have it anymore, but I'm desperate to solve this issue one way or another considering this machine will be staying in the family and in this house so will pressumably have the same issues.
Thanks in advance guys! If I've not given enough info, just ask

Wireless Access Points - Time Capsule and Netgear

Ok...Netgear support site was completely useless so I am hoping that someone over here can help me out. I think what I am trying to do is relatively simple but for 3 days now I have gotten no-joy.
Here is my current configuration: Westell DSL Modem (wireless disabled) --wired-- Netgear WNR834B (SSID 1, operating b/g mode) --wired-- Time Capsule (SSID 2, operating n mode, connection sharing Off Bridge mode). All other devices are hanging off wirelessly to one of the two routers.
What I am trying to do is add a wireless Access Point (Netgear WN802T) to the picture. I need better coverage on the other side of the house and don't want to run wires. The WNR834B is WDS compatible but I can't figure out how to put it into repeater mode or bridge mode. So I thought my next best bet (before going out and buying even more hardware) would be to try and extend the TIme Capsule network. I have been unsuccessful so far (SSIDs are the same, channels are the same, WEP set because I read somewhere that WPA was not supported in repeater/bridge mode). Is it even possible to use a Netgear Access Point with the Time Capsule (I would think it would work, but I just can't get it to).
I can get the WN802T to be seen in my network, but I can not get it to carry the internet connection.
Any advice or steps would be GREATLY appreciated.
Thanks in advance for any/all help

friars, welcome to the discussions!
Sorry, but the possibility of extending the wireless network created by the Time Capsule with a device from another manufacturer is almost zero. Based on information from other top users, the only Netgear model that is shown as WDS compatible with an Apple base station is a model WGR614 v6.
Take a look at an Apple AirPort Express to "extend" the network created by the Time Capsule. While the Express will also do WDS, the bandwidth on your network will be cut by 50% with the addition of just one WDS device. The "extend" feature on the Express does not impose this type of penalty and it is fully WPA/WPA2 capable as well, much more secure than WEP.
For about the same money as an Express, you might also consider ethernet power line adapters. Almost as good as having a direct ethernet connection. Available from Netgear, Linksys, and others.

Wireless access point advice for SMB (5 users)

I have a small site, 12 employees, five of whom will need wireless access to the LAN.
This site has an 877 (not 877W) and so I need a wireless access point.
I've been looking at the Cisco Aironet 1130AG. Can anyone make a recommendation, something that will be the same or similar to configure as wireless services on the 800 series wireless routers.
There is no domain or radius server, so any user authentication will need to be handled by the AP.
Any useful information would be much appreciated.
Thanks
Gareth

You're on the right track. The 1131AG is a great platform for small offices. It has built in antennas and is not offensive looking when mounted to the ceiling. Running a single 1131AG would allow you to run RADIUS locally on the AP so you could still use EAP security types such as EAP-FAST with WPA2.
Once you go to deploy, there are plenty of us here on the forum that can help if you run into config gotchas.
Of course I'll include the standard disclaimer that your coverage might vary based on the building construction, so you could need multiple APs to cover enough area. If certain coverage is absolutely mandatory, you should consider a site-survey beforehand.
-Eric

I can't get my macbook to access shared files on a windows computer when it's connected through a wireless access point.

I recently bought a Netgear Wireless Access Point to use in the office so we can have a wireless network. I configured the wireless network, and I am currently connected to the internet. However, I no longer can access the shared files on the Windows computers like I could when I was hardwired in with an ethernet cable. I've disabled all of the internal firewalls on all of the computers (and there's no firewall built into the WAP), all the computers are on the same workgroup, and I've tried accessing the computer with the shared files directly via the IP address using the instructions found here http://docs.info.apple.com/article.html?path=Mac/10.5/en/8849.html.
My computer sees that the other computers on the network are there. They show up in the network view from the finder. However, when I try to connect to them, it tells me the connection failed. When I click connect as, it says:
"Connection Failed
"The server “PC-ASSISTANT” may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again."
When I try to connect via the "connect to server" on the finder, I type in "smb://10.0.0.103/Word Processing" It tells me:
"There was an error connecting to the server “10.0.0.103”. Check the server name or IP address, and then try again.
If you are unable to resolve the problem contact your system administrator."
I have no clue what the problem is. I'm not really an IT person or a networking guru. Can someone please help?

You posted in the Older Hardware forum, which is for pre-year 2000 hardware. Suggest you post your question in the Airport forum at https://discussions.apple.com/community/wireless/airport
 Cheers, Tom

Radius local server and wireless access points

Similar Messages

Maybe you are looking for