RAID 0 and Bootcamp

I read some post here that stated that it is not possible to have a RAID 0 and have Bootcamp run on the Mac Pro. Is that true? Is there any possible way around this?
Thanks.

Hatter,
Thanks for the response. Would the following two scenarios allow me to run BC with a Raid 0:
1. Put Vista and Mac OS on a single, largest possible Raptor 10k boot drive, which would also run all apps. Then have a few other drives organized as a Raid 0 for storage and scratch disk purposes?
2. Put Vista on one drive, MAC OS on another (both would be separate, non-raid) then have another few drives that are organized as a Raid 0 to provide for storage/scratch disk use?

Similar Messages

Concatenated RAID and Bootcamp

Anyway to access a mac formatted concatenated RAID in windows 7 under bootcamp? MacDrive does not seem to support this.
Thanks

Hi Fred,
http://support.mediafour.com/entries/170484-macdrive-compatibility-with-raid-dri ve-arrays - so your assumption is correct.
To my knowledge there is (currently ?) no other way to access an OSX-raid from BootCamp Windows.
Sorry
Stefan

Mirrored raid and bootcamp.

On my mac i have a mirrored raid of 2 external hdds for music and photos etc.
I intend on buying a new mac soon, now I know I can just unplug and plug them into the new one no problem.
My question is though, that with my new mac i will be using bootcamp, and I am unsure what will happen if I boot into windows with my mirrored raid setup still plugged in.
Jonny

I'm going to try to install XP using an extra drive I have lying around and the Pro Caddy:
http://www.transintl.com/store/category.cfm?Category=2704
These keeps the 4 main drive bays free for OSX.

FileVault 2 and Bootcamp/Parallels

Hi,
Before I activate FileVault 2 on my Mac, I want to make sure of two things:
Will it encrypt my Win 7 Bootcamp partition or only the Macintosh HD one?
I do have a shared folder between my two partition (shared files being of course on my Mac partition). What will happen when I will access/write/remove those files when in Win 7?
Thanks

AccelerateYourMac
- there was a reader tip on just this today.
Also,
RAID and Lion's FileVault disk encryption do not mix
OS X Lion: "Some features of Mac OS X Lion are not supported for the disk (volume name)" appears during installation
OS X Lion: Installer reports "This disk cannot be used to start up your computer"
OS X Lion: About Lion Recovery

How do I install windows and bootcamp on my macbook Air

Hi
I need to install Windows and Bootcamp on my macbook Air, due to a software tool a customer needs that only runs on windows.
The initial instructions say I cannot do this with a remote DvDplayer,
Who has experienced this?
Chris

http://manuals.info.apple.com/en_US/boot_camp_install-setup_10.7.pdf

Installation of 27" cinema display with macbook pro silver key and bootcamp

For everyone out there who may be interested in using the new 27" cinema display with an older Macbook Pro Intel with silver keys and bootcamp.
What is needed:
1. Apple 27" cinema display.
2. Macbook pro Intel silver key model
3. Altona Dual Link DVI to Mini DisplayPort Converter (Model AT-DP400)
4. Bootcamp 3.1 drivers from Mac OSX Snow Leopard V10.6.3(retail)
Procedure:
1. Update your display software on the Mac OS side. Apple has posted an update on their software downloads page, "LED Cinema Display Software Update 1.0" After doing so, make sure that the 27" CinDisp is operating correctly and you can change the brightness from the system settings.
2. On the Windows side, install the bootcamp 3.1 drivers. These are on the Snow Leopard distribution CD. However, there is a bug in the .msi installer that causes the installation to go into an endless loop. This must be resolved during the installation of the drivers. The following article discribes how to do this:
http://discussions.apple.com/thread.jspa?threadID=2305631&tstart=0
3. After you have successfully installed the bootcamp 3.1 drivers, then install Apple's bootcamp update: "Apple Magic Trackpad and 27-inch LED Cinema Display Update for Windows 32 bit".
Good luck, it works!

I have the same MBP and recently bought a 23" cinema display on Craigslist for $140. It works great. I had a display port to DVI adapter and it worked fine. Built a stand to hold the laptop vertically so it's out of the way. Don't know about older displays but anything with DVI should work fine.
The screen size and resolution are great for photo editing. I now have the best of both worlds, a display that rivals my wife's iMac and portability.

General HELP for RAID and HOME NETWORK... I'm a bit lost :(

First off, I'm sorry about the long post but I just wanted to ask everything at once since I don't know what effects what?
Over the past years I've had a MBP and have always added Western Digital Mybook drives whenever I needed storage. One of clicked and died this past year and I lost some data since I was "MANUALLY" backing up. Since then I've tried to read about RAID, NAS, and DROBO type devices.
I recently bought a Mac Pro 2008 edition because I needed more speed. I mainly edit wedding photos in Lightroom but also come from a heavy motion graphics background and do some After Effects projects from time to time.
Here's a list of my current setup and what I'm hoping to achieve but I'm in over my head of what to do???
1 Mac Pro (2008 edition) - I'm considering setting up 4 1TB harddrives inside that are mirrored. I was looking at the Caviar Black or Hitachi drives...
2. I have two Airport Extreme Base Stations for my home network. (One is plugged into my Mac Pro and the other is near my Vizio LCD and Xbox 360. I've been toying around with sharing iPhoto slideshows (which I really like the idea of) The problem is that it seems really slow for video and hiccups on the stills sometimes. It doesn't seem to make a difference if it's pulling it from the Mac Pro or from a USB drive attached directly to my Airport Extreme. How do I speed this up? Is it always going to be faster to stream from the Mac Pro over ethernet cable than a harddrive plugged in through USB?
3. A few RAID and NAS solutions I've been looking at are the following but I don't really understand what I get with an external device vs an internal? I also don't know which is BETTER? for easy reliable backup.
http://firmtek.stores.yahoo.net/sata5pm2se2.html
http://www.dlink.com/products/?sec=0&pid=667
http://www.qnap.com/prodetail_feature.asp?pid=110
http://eshop.macsales.com/shop/hard-.../RAID/Desktop/
http://www.synology.com/enu/products/CS407/index.php
4. I've been reading mixed reviews about the Drobo but don't quite understand if it's a better solution then setting up a mirror INSIDE my Mac Pro. I DO NOT want to buy a $900 raid card for the Mac Pro though. Do most people choose the Drobo because they only have laptops? Should I only consider building something inside my Mac Pro?
5. I was considering Chonosync for backing up 3rd level backups
6. I just bought a Blu-Ray drive for 4th level backups that I can send off site.
7. I have all these other Mybooks. Two of them are mirrored but only one is a 1TBx2 Sata drive. The rest are IDE. I guess I'll just use these for misc things? Maybe just plug one into the Xbox for watching movies?
8. My neighbor down the hall has a similar setup and is using a Mac Mini to stream things (through Front Row) like Hulu and videos another room to his TV. Mine doesn't seem to stream fast enough. Since I have the MBP that I will use rarely since I got my desktop I was considering using that instead of Apple TV or a Mac Mini but it's too slow? Maybe I set it up wrong?
PLEASE HELP? I don't know what I'm doing.

A few RAID and NAS solutions I've been looking at are the following but I don't really understand what I get with an external device vs an internal? I also don't know which is BETTER? for easy reliable backup.
Hi,
For backup, video work, photography and expanding the Mac Pro storage capability the FirmTek SeriTek/5PM would be my choice. The bundle that you pointed to will work if 130MB/sec. is fastest enogh for your needs. The card is only $70 in the bundle which makes it a nice deal.
http://firmtek.stores.yahoo.net/sata5pm2se2.html
If you want 200MB/sec, performance I would go with the Sonnet Tempo E4P or the HighPoint RR 2314 if you desire RAID 5 redundancy.
http://www.amug.org/amug-web/html/amug/reviews/articles/sonnet/mac-pro/
http://www.amug.org/amug-web/html/amug/reviews/articles/highpoint/2314/
Trying to use NAS via the network will be 3-7x slower than the SeriTek/5PM. The SeriTek/5PM is a much better choice for backup, video and photography. NAS is good for low energy, always on, low use server needs. However, you can simply turn Mac OS X file sharing on and the Mac Pro will provide performance faster than any NAS.
Drobo - Why do people even consider this option?
The performance is USB speed even with a FW800 connection.
Users have reported losing data with firmware updates.
And the unit is one of the most expensive, slow performing options available. I cannot image ever wanting a Drobo
Backup Software:
I like SuperDuper. I also like using the "Restore" tab in Disk Utility to clone one disk to another. The key to good backup is to keep it simple and regular.
MyBook - NOT
If your storage needs exceed more than a single FireWire backup disk you really need to go with eSATA. The SeriTek/5PM and the Mac Pro combination provides virtually unlimited storage capabilities as the tray system allows new hard disk sets to be easily loaded or dismounted.
Have fun!

Many Questions on Windows 8 and Bootcamp

Hi. I have a couple questions question on windows 8 and bootcamp. I know this is probably on the internet somewhere, but i can't find it anywhere if it is. So please don't strike me down for repeat questions.
My first question is wether or not widows 8 will run on the current version of bootcamp. I know that it is not fully compatible but can it be installed with few issues since the underlying code for windows 7 and 8 should be relatively similair. I have read a posting on line that says this is possible but i wanted a second opinion. I have a 64 bit version system builder edition shipping to me right now, is this ok.
My second question is when (if ever) the patches come out for winodws 8 to run perfectly on bootcamp, will I just be able to download them, Install the patches and everything will be just fine. Would/ could it be done with out having to reinstall the operating system. This is important because a system builder lisence can only be installed once and then i have to buy another copy of windows 8 for $100.
Any and all input would be great. Thanks!

in terms of updates to win8 then as far as windows8 goes it's running on a normal "pc" not on a mac it's not virtualization here so everything works as normal
I bought an imac 2011 version 22" 4GB ....
I installed windows7 ultimate 64bit on it
since I bought the digital update to windows 8 pro
updated over the internet (you download an exe and take it from there)
it updated fine it use the windows7 drivers so everything in terms of mac stuff works as before
I let it update the amd video card driver and got a lot of crashes at bootup
rolled back to the bootcamp win7 drivers and it's a lot better
sure every now and then startup result in a crash but a reboot always get me into win8
play games and program in win8 never had a cash when I get in and because it's native games run great
likely when the official apple win8 support comes along I will stop getting the odd crash at boot into win8

My macbook pro was first installed with leopard and bootcamp 3.2. Now i updated to lion. The problem is now that it is not possible to update to bootcamp 3.3. or 4.0. The report: The installation source is not correct. What can i do? Thanks for answer.

my macbook pro was first installed with leopard and bootcamp 3.2 under windows 7. After update to lion it is no more possible to update bootcamp to 3.3. or 4.0. The report: The installation source ist not correct. What can i do?
auf Deutsch:
Auf meinem Macbook pro war Leopard und bootcamp 3.2 unter windows 7 installiert. Nach dem update auf lion kann bootcamp nicht mehr upgedatet werden. Weder auf 3.3. noch auf 4.0. Folgende Fehlermeldung kommt: Boot camp Dienste: Das installierte Produkt stimmt nicht mit der Installationsquelle überein. ... Was kann ich tun?

It means what it says. The "computer person" formatted it wrongly/ unsuitably. it needs to be formatted again.
Error "Case-sensitive drives not supported" or similar install error | Mac OS
Mylenium

Can I use *one* iTunes library for both MacOS and Bootcamp/Vista?

Does anybody know if there is a way to use and administer the same library both from MacOS and Bootcamp/WinOS?
I have Paragon's "NTFS for MacOSX", so I could actually move the library to the NTFS partition and use it from both OSes.
The thing is, the changes made on one version won't appear on the other system.
Is there a way to make both iTunes clients read/write to the same files? Is the file format of the Mac-iTunes identical with the one used by the Win version?
And isn't that an interesting question...?
Thanks for replying and cheers,
uu

The music files are currently on the Mac partition of my MacBook. I plan to move them to the Bootcamp partition, so when using "NTFS for MacOS" I can both read and write there from either partition.
To facilitate administration (e.g. when I add music files using the Mac iTunes, the Windows iTunes doesn't realize the change) I wonder if I can somehow teach both iTuneses (the one on the Mac side and the other one on the Windoews side) to write to/read the same (XML??) admin files.
...which then will have to reside on the NTFS partition as well to be readable/writable from either partition.
Is there a way to change the default path for the library files?
Message was edited by: Double-U

I have just installed 10.7 and bootcamp is no longer visible on my desktop, nor can i start computer in windows mode. I started the bootcamp 4.0 upgrade assistant, but don't want to wipe windows 7 out and lose my data. Any suggestions?

I have just installed 10.7 and bootcamp is no longer visible on my desktop, nor can i start computer in windows mode. I started the bootcamp 4.0 upgrade assistant, but don't want to wipe windows 7 out and lose my data. Any suggestions?

I have just installed 10.7 and bootcamp is no longer visible on my desktop, nor can i start computer in windows mode. I started the bootcamp 4.0 upgrade assistant, but don't want to wipe windows 7 out and lose my data. Any suggestions?

HT5219 how can I connect two thunderbolt monitors to my macmini in windows 8 and bootcamp? Works fine in OSX

how can I connect two thunderbolt monitors to my macmini in windows 8 and bootcamp? Works fine in OSX

Did you try to hook up both monitors to the Belkin adaptor? Trying will determine if your monitor has a bad input port. See if the Belkin adaptor is the problem. I have never used that specific adaptor, but I have always had luck with the Dr. Bott's DVI for ADC adaptor. Best of luck.
www.drbott.com

Can i install windows 7 via bootcamp (MB Air) while using remote disc? I put the windows 7 disk in my macbook pro drive, and connect to my brand new macbook air. In bootcamp i allocate the partition then i click install and bootcamp will not see the disk.

Can i install windows 7 via bootcamp (on my MB Air) while using remote disc? I put the windows 7 disk in my macbook pro drive, and connect to my brand new macbook air via remote disk. In bootcamp (on my air) i allocate the partition, then i click install, and bootcamp will not see the disk from my macbook pro's drive. How do i get the bootcamp assistant running on my MB air to automatically find the disk in my macbook pro with the ISO image of windows 7? The remote disk on my air can find the cd but bootcamp will not begin installing it. Anyway to do this without buying the damned usb drive?

I don't know first hand if you can use the Remote Disk option with Windows but as of 10.7.2 you can now use BCAssistant to make a bootable USB (thumb drive or external disk) W7 installer with the Boot Camp drivers installed also. Have you tried that yet?

I installed windows 7 on my iMac 21.5 (late 2009) and when I boot windows 7, the lag drivers are missing and bootcamp is not installed. The windows package would not download through bootcamp, even when left alone for 2 hours.

I installed windows 7 on my iMac 21.5 (late 2009) and when I boot windows 7, the lag drivers are missing and bootcamp is not installed. The windows package would not download through bootcamp, even when left alone for 2 hours. Don't have the lion disk... Drivers seem impossible to get. Please help!

lan drivers*

Windows 7 on Bootcamp I am locked into a DOS screen and it is not installing. I have been on line with Apple and microsoft and they can't help. I have lated versions of Lion and bootcamp. HELP

I ran bootcamp and tried to install Windows 7. I end up with a DOS screen and an unresponsive keyboard.
I have been on line with Apple and microsoft and they can't help. I have lated versions of Lion and bootcamp. HELP!
My Lion is up to date.
I used the 64-bit windows disc.
Should I try parallels?

Do you have a DOS screen with a command prompt or just a blank screen?
Is your Windows 7 x64 an original MS Full Version Installation DVD?
Did Windows 7 Install Disc start?
If it did you would have had to choose the location of where to install Windows 7.
Did you select the Partition named BOOTCAMP that corresponded to the Partition Size you created in BootCamp?
Were you asked to format the Partition?
Did you format the partition to NTFS and then get an option to click NEXT and actually start the Windows 7 installation?
Do you have a wired USB keyboard and wired USB mouse?
If you actual went through the installation and restarted then here are some things to try:
First try doing a CONTROL-ALT-DELETE and see if a Windows Option Screen appears.
If you get the Screen you will have some options displayed.
You want to highlight and click TASK MANAGER which should be the bottom choice I beleive.
If Task Manager runs you will get a window showing all the processes running.
See if you can find EXPLORER.
If EXPLORER is running highlight it and go to the bottom right and click the END TASK button.
Now go to the Top Left Menu Bar.
Click FILE
In the sub menu that opens select RUN or RUN NEW TASK (Not sure which it is in Windoes 7 as I am running Windows 8)
Once RUN is selected a new window will open to CREATE NEW TASK
Type in EXPLORER and then the OK button.
If Windows 7 installed properly the Desktop should appear after a bit of time.
Your first concern is to get your keyboard running so you may have to remove and reinstall Windows using Boot Camp on the Mac Side.
Let us know how it goes..

HT4818 I have installed bootcamp that worked properly. Then I have partitioned the OS X 10.8.2 and installed another OS X 10.8.2 and I have got two MAC boot options and Bootcamp disappeared from the Option menu. How can I boot Windows again and keep both

I have installed bootcamp by the bootcamp assistant and worked properly.
Then I have partitioned the OS X 10.8.2 and installed another Mountain Lion System and I have got two MAC boot options and Bootcamp disappeared from the Option menu. However, Bootcamp still remained in the Startup Disk in the System Preferences. When I tried to boot Bootcamp using the Startup Disk it did not boot and received a message that there is no bootable device. I have not lost any data and can read Bootcamp partition from both OS X systems. Please advise how can I boot Windows / Bootcamp again? Thank you.

Recommendation 1: Use a VM for this. It's essentially a giant C.F. to do this with native booting, and is potentially fragile.
But if you're going to ignore that and do this anyway, realizing that it can break anytime in particular with OS upgrades, and that it's very difficult to impossible to resize the three volumes once you've installed the systems:
1. create three partitions, setting each to be the size for OS X copy 1, copy 2, and Windows respectively. The Windows partition needs to be set to MS-DOS format (actually FAT32) which later in the Windows installer you'll reformat as NTFS. Do not use Boot Camp Assistant to resize/partition the disk, it simply won't work for this use case.
2. install OS X copy 1
3. install OS X copy 3
4. Use gdisk (available at sourceforge) which is a command line only application, to create a new hybrid MBR adding only the last partition (Windows) to the hybrid MBR and setting it to be bootable. As a concequence you will not be able to see/share either OS X volume from within Windows. The Windows NTFS volume will be visible from within OS X.
5. Install Windows to the only partition its installer should see (confirm size), you'll need to format it NTFS first, and I suggest using the fast format option if available.

RAID 0 and Bootcamp

Similar Messages

Maybe you are looking for