RAID 0 is not visible

hi *
[OS:Centos 5; Intel ICH10R SATA RAID; 5 SATA harddrives on board]
I've got a question - what the reason could be that RAID 0 made up this way:
vol0 = sdb+sdc
vol1 = sdd+sde
(and sda is left for OS)
configured in BIOS-like interface before OS boot,
is not visible when OS is started (fdisk shows plain disk as if they were never configured in a RAID):
# cat /proc/mdstat
Personalities :
unused devices: <none>
# fdisk -l
Disk /dev/sda: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 * 1 13 104391 83 Linux
/dev/sda2 14 37368 300054037+ 83 Linux
/dev/sda3 37369 38913 12410212+ 8e Linux LVM
Disk /dev/sdb: 320.0 GB, 320071851520 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
Disk /dev/sdc: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
Disk /dev/sdd: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
Disk /dev/sde: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/sde doesn't contain a valid partition table
Edited by: g777 on 2010-06-18 07:39

ok, I've found the answer by myself - this RAID system is destined for Windows only (both drivers and console). So I'll do it on OS level. Bye.

Similar Messages

Hard drives not visible in Disk Utility

I decided to add two additional 1.5 TB drives to my (early 2008) Mac Pro, in addition to the two 1.0 TB drives already there. I have a Mac RAID card, but the drives were not configured into an array because I was having battery and setting problems with the RAID card as described in previous posts.
I perhaps got the the not so bright idea to reconfigure my system from scratch, so I put the two 1.5 TB drives in, created partitions via Disk Utility, and then took all the drives out. I then put one of the new 1.5 TB drives in only, and re-installed OS X. So far, so good. Then, I put all 4 drives in, including the previous 1.0 TB drive with OS X on it.
Interestingly, the system then booted to the old 1.0 TB drive with OS X, and then it 'hung' on something with the spinning icon. I shut it down, and then put the new 1.5 TB with OS X, but it would not start. I yanked out the RAID card, figuring it was not helping. I managed to put the Boot DVD in, and the system does boot to DVD. However, it cannot visualize any drive at all, only the two DVDs in Disk Utility.
I tried several things. One is hardware scan by holding the 'D' key on startup -> no errors.
I then tried resetting the PRAM holding the command-option-P-R keys, same issue - boots to DVD, but no drives.
I then tried resetting what I think is the SMC, which is a button on the motherboard down near where the memory slots, and there a green light comes on next to the STBY area.
I'm out of the Apple care warranty, and I guess I'll have to pay for support going into the Mac Store, but I am hopeful someone has an idea.
I wondered if the cable from the SATA connector to the motherboard was loose, but it appears intact. However, I'm not sure how to get the plastic cage off.

Good idea, but the RAID card is out, and even the original drives are not visible. There is some type of BIOS or some related error.

Our XServe-RAID volume does not mount anymore...

Our XServe-RAID volume does not mount anymore.
On /var/log/system.log I could find the following.
Feb 22 09:52:29 ogre kernel: jnl: open: journal magic is bad (0xf433f != 0x4a4e4c78)
Feb 22 09:52:29 ogre kernel: hfs: early jnl init: failed to open/create the journal (retval 0).
It appears the the journaling is badly screwed.
I tryed to disable the journaling with no success.
Here is what I get.
ogre:/var/log root# diskutil disablejournal disk2s3
The selected journaling request does not appear to be valid
After some googling I foud this :
--- QUOTE ---
The more serious problem occurs when the contents of the journal file are corrupted in such a way that the operating system does not proceed to mount the volume. Fortunately, this problem is extremely rare (I have seen three reports of corrupted journal files at the MacFixIt Forums and Apple Discussion Forums since journaling was introduced).
Starting the journaling process is one of the first things that happens when a volume is recognized by the operating system. There appears to be no way to intervene in single-user mode before the journal file is examined. A message about �bad journal magic� appears. Unfortunately, every tool that can turn off journaling requires that the volume already be mounted.
If the Macintosh can boot under Mac OS 9, dealing with a corrupted journal file involves restarting under Mac OS 9 and using a utility (such as our free TechTool Lite 3.0.4) to make visible these two invisible files at the root level of the volume:
/.journal
/.journalinfoblock
Once these files are made visible, they can be deleted. Mac OS 9 does not support journaling, and recognizes nothing special about these files. Neither of these files can be seen in Terminal or in single-user mode in Mac OS X, because they are considered part of the disk directory.
If the Macintosh cannot boot under Mac OS 9, but the drive has Mac OS 9 drivers installed, the drive can be put into a Macintosh that can boot under Mac OS 9, or an ATA/IDE drive can be put into a suitable FireWire enclosure.
The possibility that you may need to remove these two journaling files under Mac OS 9 is a good reason for making sure that all volumes you use have Mac OS 9 drivers installed. The drivers must be installed when the drive is formatted.
--- [END] QUOTE ---
Well, my disk is part of a RAID 5 matrix.... so the solution proposed does not work.
Does any one of you has any idea ?
XServe Mac OS X (10.3.9)

I've seen an article about volumes not mounting and was wondering if this relates to your problem;
http://discussions.apple.com/thread.jspa?messageID=1239224&#1239224
The thread doesn't refer to journalling but may be of use?
HTH

External hard drive not visible in disk utility or finder

Hi all,
I have had a good look through previous discussions and I can't seem to find an issue relevant to mine.
My external hard drive has 2 partitions (1 time machine back up, 1 general hard drive). The issue is that the HD is running when it is plugged in however it is not visible in either disk utility or finder.
I am running OS X 10.10 (Yosemite) on a 2010 MacBook Pro. I also have parallels desktop running windows 7. When I boot windows and plug in the HD I usually get the option to mount the HD to either OS X or Windows. With this issue the option window appears for a split second (not enough time to select either) and then disappears. It seems that the HD may be ejecting itself as soon as it is registered by the computer. I have tried using a different power cable for the HD and also a different usb cable, this doesn't help.
The external HD is a Samsung D3 Station, which i have had for 6 months now and never had an issue with.
Any help is appreciated
Thanks,
Bruce

An update for anyone who can help me:
I have tried the external hard drive in other computers (mac and windows), each time I get the same problem above.
I have removed the HD from the enclosure and purchased a docking station for it (3.5" SATA). When I plug it in to the laptop it disconnects itself straight away before it is visible. With the windows computers it installs the drivers and says that the device is ready to use, then disconnects before it shows up.
As the HD is not visible there is no option to re-format or anything.
This is very frustrating as I was using the HD with no issues and it randomly disconnected and I have not been able to access since.
Thanks in advance for any help.
Bruce

Hi - I am looking for the Adobe Illustrator 2014 1.2 (or .0.2) bugfix update for Mac - and it is not visible in the Adobe Creative Cloud Packager (Mac version). The only update visible is Illustrator CC 2014.1 - which is what introduced the bugs.

Hi - I am looking for the Adobe Illustrator 2014 1.2 (or .0.2) bugfix update for Mac - and it is not visible in the Adobe Creative Cloud Packager (Mac version). The only update visible is Illustrator CC 2014.1 - which is what introduced the bugs.
The only thing that I can think of that might be causing the issues that I have a Mac Mini on Mavericks.
Dave

Hi
I have discovered that my question above is a non-question. A user triggered by looking at the below article about Illustrator 2014 cc 17.0.2
http://helpx.adobe.com/illustrator/release-note/illustrator-17-0-2-release-notes.html
He had recently upgraded from wht we now know is 18.0 to 18.1 which is the latest version. He read the above artic
le and supposed that it was a bug fix release for his version - because the v17 ov18 number is not often displayed. It is usually just 2014 CC.
I have asked him to post a bug report about Adobe Illustrator CC 2014.1
Dave

Raid Utility Error Message "raid utility is not supported on this computer"

I am not doing anything that I know of, but Raid Utility keeps opening up on its own, and a message pops up multiple times a day telling me "raid utility is not supported on this computer"
Anyone have any idea how to fix this?

Network startup is if you want to start your macbook using a network drive.
Keep your startup settings at your current drive.
Raid utility doesn't apply to you since you only have one hard drive installed, unless you installed another hard drive in your optical bay.
Fibre Channel is another type of hard drive connection via network connection.
You can't access things you don't have installed in your macbook. Those are there in case you decide to have a network drive start up options, a raid configuration of a fibre channel network drive.

IDOC not visible in IR but metadata successfully imported

Hi,
I have this wiered issue.
I want to import IDOC WPUSKR01 (cashier productivity) from BI.
But when I connect to BI system from IR to import Idoc structure, this IDOC is not visible.
But I can manually import the metadata from BI in idx2.
Now how to import this in IR?
I have imported other Idocs (like WPUBON) before and did the scenario successfully for BI.
Regards,
Anirudh Vyas.

Hi,
In BI Tcode we82 I have manually added the entries for WPUKSR01. Now Idoc is visible when importing in IR.
I have checked all the segments in we31, they are all released.
But it gives error:
Error: IDoc type WPUKSR01 contains errors (unable to read segments)
Then, I checked in R/3, there also WPUKSR01 was not there in we82. I manually added there and I was successfully able to import it in IR.
But the same thing is failing in BI. I have SAPALL permissions in all the systems.
Can I use Idoc imported from R/3 in scenario for BI?
regards,
Anirudh.

How can I add a device to my library? My e-reader is registered but not visible.

Hello,
I use a Tolino Shine and can download E-Books via WLAN directly to it. I can also download the books to my netbook. However, when I plug the Tolino into my netbook it is not visible in the Adobe library and I cannot move books from the library to the Tolino.
I tried to reset the Tolino to the manufacturer settings. This did not improve the situation.
Any suggestions?
Thanks a lot!

http://www.apple.com/icloud/find-my-iphone.html
any chance of it working on non-apple phones?
No, it requires the operating system iOS, only available on Apple Devices.

Reporting Flag is not visible in the manage screen

Hi BI Experts, Good morning.
We load the inventory data daily in the night time which is delta load.
5 days back, we got 0 records and the request is in red.Then i rerun the infopackage manually and got the total records in to the cube.
From that day onwards its running successfully.
Yesterday i deleted the bad request from infocube.
But the Reporting flag is not visible.
Today i didnot get the records.
Please can anyone tell me the process.
Thanks in advance.
Regards
Anjali

Hi Nagesh,
Still i am not getting reporting flag.
I tried what did u say.
And today i did not get the records. Infopackages didnot run. It shows in red.
I tried to run it manually but it gives error.
The error message is:
Short text
    An exception occurred that was not caught.
What happened?
    The exception 'CX_RSR_X_MESSAGE' was raised, but it was not caught anywhere
     along
    the call hierarchy.
    Since exceptions represent error situations and this error was not
    adequately responded to, the running ABAP program 'SAPLRRMS' has to be
    terminated.
Please give me the reply.
Thanks in advance
Regards
Anjali

Drop down boxes do not show up. My tabs are not visible. I could barely see the box to type in this question. Something is off. I deleted and reinstalled program it is still just floating words. I work on a Mac with ox 10.6.8

The browser boxes, tabs, and links do not show up with the needed outlines, colors, and shapes. This box I am typing in was barely visible. Above this box is a set of two verticle parallel bars. When I moused over it, I saw it was for inserting a link, but if I had not been curious I would not have known what those lines were for. When I look at this page on PC I have a colored blue backdrop. It is not visible on the Mac. The search box does not have the image of the magnifying class and the arrow does not show up where it should be. The words Post Question just appear below the statement we have made some educated guesses about your browser. I thought maybe it had been a theme that was applied, but I do not see how it could have come on when I trashed the old version of the firefox.

A;though the CSS is very well documented, there are those that ignore those signs. Look at the following
/* Menu item containers, position children relative to this container and are a fixed width */
ul.MenuBarHorizontal li
    margin: 0;
    padding: 0;
    list-style-type: none;
    font-size: 100%;
    position: relative;
    text-align: left;
    cursor: pointer;
    width: auto;
    float: left;
The rest have been given a width of 15em, so this value may be a good start.
DESIGN INFORMATION: describes color scheme, borders, fonts
/* Submenu containers have borders on all sides */
ul.MenuBarHorizontal ul
    border: 1px solid #CCC;
   width: auto;
    background-attachment: fixed;
Just keep the border property and remove the other two.
BROWSER HACKS: the hacks below should not be changed unless you are an expert
/* HACK FOR IE: to make sure the sub menus show above form controls, we underlay each submenu with an iframe */
ul.MenuBarHorizontal iframe
    position: absolute;
    z-index: 1010;
/* HACK FOR IE: to stabilize appearance of menu items; the slash in float is to keep IE 5.0 from parsing */
@media screen, projection
ul.MenuBarHorizontal li.MenuBarItemIE
          display: inline;
          f\loat: left;
          background: #FFF;
The following is the original for the above
BROWSER HACKS: the hacks below should not be changed unless you are an expert
/* HACK FOR IE: to make sure the sub menus show above form controls, we underlay each submenu with an iframe */
ul.MenuBarHorizontal iframe
    position: absolute;
    z-index: 1010;
    filter:alpha(opacity:0.1);
/* HACK FOR IE: to stabilize appearance of menu items; the slash in float is to keep IE 5.0 from parsing */
@media screen, projection
    ul.MenuBarHorizontal li.MenuBarItemIE
        display: inline;
        f\loat: left;
        background: #FFF;
Cheers,
Gramps

Data loaded in Infocube is not visible in the Reporting

Hi all,
In the info cube, the data is not visible for reporting, How can i make it available for reporting,
When i select the Manage option from the context menu of the cube and select the Requests Tab, i get a pop up message that tells
" There is an inconsistency between the load status of the data and the option of reporting on this data.
There is data in the InfoCube/ODS object that is OK from a quality point of view, but is not yet displayed in reporting.
The problem, for example, is to do with request 0000018049, number REQU_F4ZBFRMDGBULE9WCUN3R5UX5X."
How do i find out the inconsistancies?
PS: All the requesta are delta upload
There is no aggregates for this cube.
Thanks n regards
Girikumar

Hi Girikumar
Use the RSRV transaction and select All Elementary Tests in the dropdown ->Transaction data , select the Consistency of the Time Dimension for an InfoCube and select your cube and Execute the button ..if any error are there it will display the inconsistency ..Repair the Inconsistency with Correct Button..
Check the other test also ..
Hope the above helps you..\
Bye
Shu Moh..

I updated win7 and now I cant see ff. I have reinstalled it 5 times now. It shows it is running in task manager but it is not visible on the desk top.

I installed win7 ultimate and then ff. ff worked fine until I installed win7 service pack 1 and all the other updates it recommended. I click to open ff and nothing happens. I look in task manager and it shows it is running. It is not visible on the screen or in the task bar. I have reinstalled a fresh download of it 5 times. I even tried the beta version but still the same problem. I can use explorer and chrome ok but not ff.

The "System Tray" is located at the very bottom right of your screen and is a list of most/all running applications that will show in this list.
For your SysFader issue, this "may" be the problem:
1 Find the "My Computer" desktop icon and right-click it. A pull-down menu will appear. Select "Properties."
2 Click on the "Advanced" tab. This will load a new page of options.
3 Select the "Visual Effects" tab at the top of the window and deselect "Animate Windows when minimizing and maximizing," "Fade or slide menus into view," "Fade or slide Tool Tips into view" and "Fade out Menu items after checking."
4 Click "OK." This will remove most if not all of the Sysfader effects, at the same time correcting related errors that used to come up during opening a new file or program.

After activation of atandard business content key figure is not visible

Hi all,
I am trying to implement inventory management scnerio in BW3.5 using screen shot PDF , for this i activate standard business content ( cube : 0IC_c03 ) and activate all its related object . one of my key figure 0RECVS_VAL I want to change its parameter for this when I search this infoobject in Infoobject tree this is not visible
while its present in cube 0IC_c03 ,can anybody tell me for changing in this key figure what can i do???
Thanks and regards
Ankit modi

Hi
Again it install from BI content and do the changes what ever u want by RSD1
Cheers
Edited by: SDN USER on Jun 26, 2008 12:04 PM

Hierarchy in properties of characteristics item is not visible in report

Hi,
It has been observed that the Hierarchy name in u201Cproperties of characteristics" of an infoobject for example 0GL_ACCOUNT is not visible in BEx output report. The report shows complete hierarchy with all nodes / subnodes but NOT HEADER description!
Also whenever you change the hierarchy (by changing global / local view), Same problem exist.
This is one of the high priority problem users are facing since they canu2019t see hierarchy name (Key / Text) causing confusion.
Please advice.
Thanks and best regards
Rajendra

Make a duplicate header above all the levels and show text in the BEx output
Level 1 -> Hierarchy name -> Level 2 ( Initially Level 1) -> Level 3 ( Initially Level 2)

The Horizontal & vertical scroll is not visible or not working when i run the form in Forms 6i.

Hi all,
The Horizontal & vertical scroll is not visible or not working when i run the form.
In this form , there are 5 canvas namely
CANVAS2 - Stacked Canvas
PASS - Content Canvas
MAT_RATES - Content Canvas
DATE - Content Canvas
PREVIOUS - Content Canvas
I have set "Show Horizontal Scroll Bar" to "Yes" and "Show Vertical Scroll Bar" to "Yes" in the WINDOW Property.
I have set "Show Horizontal Scroll Bar" to "Yes" and "Show Vertical Scroll Bar" to "Yes" in the STACKED CANVAS Property .
But still the Horizontal and Vertical Scroll Bar is not working when i run the Form.
Help me with this please. How do i make it visible??
Oracle Forms 6i..
Thank You.

Vijetha wrote:
Hi all,
The Horizontal & vertical scroll is not visible or not working when i run the form.
I have set "Show Horizontal Scroll Bar" to "Yes" and "Show Vertical Scroll Bar" to "Yes" in the WINDOW Property.
I have set "Show Horizontal Scroll Bar" to "Yes" and "Show Vertical Scroll Bar" to "Yes" in the STACKED CANVAS Property .
But still the Horizontal and Vertical Scroll Bar is not working when i run the Form.
Help me with this please. How do i make it visible??
Oracle Forms 6i..
Thank You.
hello vijetha,
window and canvas show scroll bar when it need.
You should show block property
and set block scroll bar
hope this helps..
Hamid

RAID 0 is not visible

Similar Messages

Maybe you are looking for