RAID 1 setup fails with POSIX error
I am trying to set up a RAID 1 array using 2 brand-new Iomega eGo 2TB Desktop Hard Drives. They are connected via Firewire 800, with the second connected to the first through Firewire pass-through. I'm on 10.6.8, on an iMac 9,1 with the 2.66Ghz Core 2 duo and 8GB RAM.
I complete all the steps to create the RAID array, add the drives to the array, select "Automatically rebuild RAID mirror sets", and when I hit "create", Disk Utility unmounts the disk, starts to create the array, and then gives me the following error.
Creating RAID set failed with the error:
POSIX reports: The operation couldn't be completed. Operation not permitted.
Am I doing something wrong in the setup? Does this mean one of the drives is a dud? Does this mean I can't create a RAID array with pass-through Firewire drives?
Any help or advice would be greatly appreciated.
I ran the 1.1.1 upgrade this afternoon. I've been through the same process three times, but I was getting error 1602. Now when I unplug, reboot the Mac and reboot the phone, wait for everything to load, iPhoto recognizes the camera/pictures, but iTunes does not recognize the iPhone, and when it does, I get the spinning color wheel until I'm told that my iPhone timed out (or I get the error message above again). I've not hacked the iPhone, and even though iTunes isn't recognizing it, the phone is as fully functional as it was before the ill fated upgrade.
There is a support article but it appears to be geared towards Windows.
Error 1601 or 1602 when restoring iPhone or iPod touch in iTunes
Issue
When trying to restore your iPhone in iTunes, you may see the following message followed by an error code 1601 or 1602:
The iPhone could not be restored. An unknown error occurred.
Or when trying to restore your iPod touch in iTunes, you may see the following message:
The iPod "[username]" could not be restored. An unknown error occurred (1602)
Products affected
iPhone
iPod touch
iTunes 7.4 or later
Solution
Restart the computer and try to restore the iPhone or iPod touch again.
Completely remove iTunes and Apple Mobile Device support and then reinstall iTunes. Select the appropriate link below for instructions on how to accomplish this for your operating system.
Windows XP
Windows Vista
Try restoring the iPhone or iPod touch on a different computer using iTunes (if another computer is available).
Message was edited by: Lane Baysden
Similar Messages
-
I plug usb mass storage device to my macbook pro i7 than every thing is stack and i reinforce to shutdown and than I start again but mac fail to boot again.
I tried different optiones in disk utility in mac os startup disk. but still fail to repair, erase and partition. I try to fix with the steps listed in
https://discussions.apple.com/message/13288923#13288923
but it fail to partition with the msg:
Partition Failed
Partition failed with the error: POSIX reports: The operation couldn’t be completed.cannot allocate memory
pls pls pls help urgentely on this matter I stop working.
Kind Regards,
peHi again OGELTHORPE.
I've already run two hardware tests. One quick one and one extended one. It was unable to pick anything up.
It's like everything is running perfectly, but when I go to erase the HDD or partition it, it pops up with the error message. Even when I try to erase and partition using "Terminal", I received the same error message.
It's beginning to do my head in, but will see if replacing the SATA cable will make any difference. If it doesn't, I'll hazard a guess it could be the Logic Board.
Thanks again for your suggestions!
L. -
Hi,
I am trying to install certificate services on a windows 2008 server (R2 ENT SP1) with a PCIe nCipher HSM module installed on it. The version of nCipher SW is = 11.30. It is a RootCA, and I am trying to use a key that is already stored in the HSM (I
have done this before with a PCI HSM (older HW version)). I select “Use existing private key” and “Select an existing private key on this computer” on the wizard, then i change the CSP to nCipher and click on "search" the key I am looking for
appears and I select that one. I repeat, I have done this before and it works with a PCI HSM module.
The installation is finished before being prompted to insert the operator cards, and it ends with two errors:
<Error>: Active Directory Certificate Services setup failed with the following error: Overlapped I/O operation is in progress. 0x800703e5 (WIN32: 997)
And:
<Error>: Active Directory Certificate Services setup failed with the following error: The group or resource is not in the correct state to perform the requested operation.
0x8007139f (WIN32: 5023)
The servermanager.log says:
1856: 2014-07-23 18:27:48.195 [CAManager] Sync: Validity period units: Years
1856: 2014-07-23 18:27:48.928 [Provider] Error (Id=0) System.Runtime.InteropServices.COMException (0x800703E5): CCertSrvSetup::Install: Overlapped I/O operation is in progress. 0x800703e5 (WIN32: 997)
at Microsoft.CertificateServices.Setup.Interop.CCertSrvSetupClass.Install()
at Microsoft.Windows.ServerManager.CertificateServer.CertificateServerRoleProvider.Configure(InstallableFeatureInformation featureInfo, DiscoveryResult discoveryResult, ChangeTracker changeTracker)
1856: 2014-07-23 18:27:48.928 [Provider] CAErrorID: 0, CAErrorString: 'Active Directory Certificate Services setup failed with the following error: Overlapped I/O operation is in progress.
0x800703e5 (WIN32: 997)'
1856: 2014-07-23 18:27:48.928 [Provider] Adding error message.
1856: 2014-07-23 18:27:48.928 [Provider] [STAT] For 'Certification Authority':
And:
1856: 2014-07-23 18:27:49.053 [CAWebProxyManager] Sync: Initializing defaults
1856: 2014-07-23 18:27:49.162 [Provider] Error (Id=0) System.Runtime.InteropServices.COMException (0x8007139F): CCertSrvSetup::Install: The group or resource is not in the correct state to perform the requested operation. 0x8007139f (WIN32: 5023)
at Microsoft.CertificateServices.Setup.Interop.CCertSrvSetupClass.Install()
at Microsoft.Windows.ServerManager.CertificateServer.CertificateServerRoleProvider.Configure(InstallableFeatureInformation featureInfo, DiscoveryResult discoveryResult, ChangeTracker changeTracker)
1856: 2014-07-23 18:27:49.162 [Provider] CAErrorID: 0, CAErrorString: 'Active Directory Certificate Services setup failed with the following error: The group or resource is not in the correct
state to perform the requested operation. 0x8007139f (WIN32: 5023)'
1856: 2014-07-23 18:27:49.162 [Provider] Adding error message.
Has anyone experienced this before? Am I missing something here?
Any help will be very appreciated
Thanks in advance
Best regards
Alejandro Lozano VillanuevaHi, thanks for your support.
I have been playing around a bit with some ncipher commands and found this:
C:\Program Files (x86)\nCipher\nfast\bin>cspcheck.exe
cspcheck: fatal error: File key_mscapi_container-1c44b9424a23f6cddc91e8a065241a0
9aa719e4f (key #1): 0 modules contain the counter (NVRAM file ID 021c44b9424a23f
6cddc91)
cspcheck: information: 2 containers and 2 keys found.
cspcheck: fatal error occurred.
If I perform the same command on the original server (the server with the original kmdata folder and with the running RootCA services):
E:\nfast\bin>cspcheck.exe
cspcheck: information: 2 containers and 2 keys found.
cspcheck: everything seems to be in order.
Strange?
Moreover, when I do a csptest.exe command (also on both servers, i find this)
On the new server:
C:\Program Files (x86)\nCipher\nfast\bin>csptest.exe
nCipher CSP test software
=========================
Found the nCipher domestic CSP named 'nCipher Enhanced Cryptographic Provider'
Provider name: nCipher Enhanced Cryptographic Provider
Version number: 1.48
User key containers:
Container 'csptest.exe' has no stored keys.
Container 'Administrator' has no stored keys.
Machine key containers:
Container '352dd28a-17cb-4c6f-b6e4-bf39bcf75db5' has a 2048-bit signature key.
Container 'ROOTCA' has no stored keys.
Container 'csptest.exe' has no stored keys.
While in the old server:
E:\nfast\bin>csptest.exe
nCipher CSP test software
=========================
Found the nCipher domestic CSP named 'nCipher Enhanced Cryptographic Provider'
Provider name: nCipher Enhanced Cryptographic Provider
Version number: 1.40
User key containers:
Container 'csptest.exe' has no stored keys.
Machine key containers:
Container '352dd28a-17cb-4c6f-b6e4-bf39bcf75db5' has a 2048-bit signature key.
Container 'ROOTCA' has a 2048-bit signature key.
Container 'csptest.exe' has no stored keys.
As you can see, the container called ROOTCA, which is the one that I use during the installation, says it has no stored keys. While on the old server, it says it contains a key. Why is this happening? I dont know, I am copying the complete
key management folder from one server to another and initialize the security world with that folder as I always do, and i dont have any errors during this procedure.
Do you know what could be the cause of this? or how can I fix this? Thanks a lot, best regards.
Alejandro Lozano Villanueva -
I get the following error when formatting a external hard drive.
Partition failed with the error:
POSIX reports: The operation couldn’t be completed. Cannot allocate memory
I have a Macbook pro 13" A1278. I purchased it around december 2010. I have a HHD 3.5" drive desktop select II 1.5TB. I purchased it around Febuary/March 2011 to use with my Macbook pro. I formatted it and moved all my files to there, I got it so my macbook's hard drive wouldn't brake and I lose everything on my macbook.
Is there any fixes?First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. From iTunes, select the iPad/iPod and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes." -
Java 2 runtime Environment setup failed with a return code of -1
Hi!
I have tried to install sdk 1_3_1_01 on Windows 2000 with ServicePack 2 and the error "Java 2 runtime Environment setup failed with a return code of -1" occured. As I saw, a lot of people has the problem but couldn't find a solution on this page!
Please help !
MeI've installed 1.3.1_01 on both W2K Workstation and Server, no problem. There's a bug report, but no workaround or solution.
http://developer.java.sun.com/developer/bugParade/bugs/4412291.html
and it's supposedly 'fixed' in 1.4.0 beta.
http://java.sun.com/j2se/1.4/fixedbugs/fixedbugs-beta2.html
You might try installing the beta version
http://java.sun.com/j2se/ -
Hi everyone,
We are trying to create silent(unattended) install package to install Oracle database 11g express edition 11.2.0 silently on our machines. We modified the provided .iss file as per the requirement and tried to install with below command,
setup.exe /verbose /s /f1"c:\DISK1\response\oracleXE-install.iss" /f2"c:\DISK1\oracle_log.txt" /v" /l*v "c:\DISK1\oracle_msi_log.txt""
Installation is failing with below error from the log file,
1: OracleXE-Server-Install-Message: Port 8081 is in use. Specify a different port number.
Installshield 11:22:22: Installation aborts, ready to shut down.
Port 8081 is being used by mcAfee in our organization. We tried passing a different port number for Http in the response file(.iss), but it is failing with same reason. We have searched foruns and found that we need to stop the port8081 during the oracle XE installation and can start it later once the installation is completed. But As port 8081 is being used by McAfee in our organization, we could not stop it even during oracle XE installation as it creates security issues.
I am attaching the MSI log(failure log) and modified .iss(modfied .iss file to .iss.txt to be able to attach) files. Please look into it and suggest how can we achieve silent installation in this case.Pl see previous discussions about this topic - seems to be a limitation of the silent install process
OracleXE-Server-Install-Message: The 8081 port is in use. -
Installation fails with "internal error 2502"
I have a client running Windows Vista Home Premium Edition (32 bit) and my app's CVI-built installer fails with "Internal Error 2502".
This installation kit has been successfully deployed on hundreds of computers with various versions of Windows and I have never seen this one. No device drivers or advanced libraries - just the standard runtime. I use CVI 9.0.1.
Searches reveal very little - some old issues with Office installation, date/time settings etc. but I have yet to find anything that indicates what this error represents.
Any insights or ideas very welcome.
Thanks,
Ian
Solved!
Go to Solution.That appears to be a Windows Installer (MSI) error, and can have many different causes. Can you confirm that anyWindows installers (perhaps try newest Adobe Reader) work on that system? Is the system's date/time set correctly? Could there be a permissions restriction with C:\Windows\system32 or C:\Programs\National Instruments\Shared?
I'd also try doing an internet search for "installer error 2502" and see what other tips you might find. If all else fails, try running the installer from the command line like this:
setup.exe /log install_log.txt
That will generate a log file that might contain a hint for us.
Mert A.
National Instruments -
I am trying to download & install Photoshop 6 but setup fails with "Installer failed to initialize
I am trying to download & install Photoshop 6 but setup fails with "Installer failed to initialize Download Adobe Support Advisor" I then downloaded and ran the Support Advisor; it reported NO problems.
I can still can not load Photoshop 6!Lw_jr01 to clarify when you are trying to install Photoshop CS6 you are receving the error message that the, "Installer Failed to Initialize." Is that correct? If so which operating system are you using?
-
Rendering of Proxies in AE fails with generic error messages.
*sigh* working with AVC in CS4 on my quad core has been an exercise in pain.
I've followed the optimization guides linked to in the different forum posts and that lets me zip along until I actually start adding effects. Then I am right back to a crawl. I recently discovered proxies in AE and learned that I can use "replace" in premeire to leverage those same proxies... Sweet... When I works I am back to editing in both in real time!
The problem is AE is regularly failing to generate proxies for me and I cannot figure out why. All my video is shot the same 24mbps, 60fps, 1080p (true 60i). All shot from my Canon HF S10.
The error is always "Error reading frame from file" and it always occurs just before the render is about to complete. Sometimes I get lucky and a working .mov was generated in spite of the error. Bu most times the file isn't there.
So my 2.4ghz quad core with 8gb ram can't edit the originals and I can't create proxies... I'm effectively dead in the water.
I tried using Media Encoder to generate my proxies with no success either. It fails with "Unspecified Error".
Both times I am trying to encode to Quicktime, Jpeg, Draft Settings. For the heck of it I tried different codecs, etc. Nothing seems to help. Even worse is sometimes if I just queue the same file multiple times it eventually works.
Is there anything at all I can do to make successful proxy generation less like winning the lottery?Yeah I updated to that right away. Premiere itself seems to behave most of the time. To be honest I've hardly had any problems with Premiere even before the 4.2 update.
But AVC (mts files) seem to be very problematic in AE in general. I also experience the issue mentioned here:
http://forums.adobe.com/message/2404464
Sounds like re-encoding to another format is the only way I'll be able to work in AE reliably. So I have to figure out a way to get Media Encoder to finish it's jobs. -
Cube refresh fails with an error below
Hi,
We are experiencing this problem below during planning application database refresh. We have been refreshing the database everyday, but all of a sudden the below error is appearing in log. The error is something like below:
Cube refresh failed with error: java.rmi.UnmarshalException: error unmarshalling return; nested exception is:
java.io.EOFException
When the database refresh is done from workspace manually, the database refresh is happening successfully. But when triggered from unix script, its throwing the above error.
Is it related to some provisioning related issue for which user has been removed from MSAD?? Please help me out on this.
Thanks,
mani
Edited by: sdid on Jul 29, 2012 11:16 PMI work with 'sdid' and here is a better explaination of what exactly is going on -
As part of our nightly schedule we have a unix shell script that executes refresh of essbase cubes from planning using the 'CubeRefresh.sh' shell script.
Here is how our shell looks like -
/opt/hyperion/Planning/bin/CubeRefresh.sh /A:<cube name> /U:<user id> /P:<password> /R /D /FS
Here is what 'CubeRefresh.sh' looks like -
PLN_JAR_PATH=/opt/hyperion/Planning/bin
export PLN_JAR_PATH
. "${PLN_JAR_PATH}/setHPenv.sh"
"${HS_JAVA_HOME}/bin/java" -classpath ${CLASSPATH} com.hyperion.planning.HspCubeRefreshCmd $1 $2 $3 $4 $5 $6 $7
And here is what 'setHPenv.sh' looks like -
HS_JAVA_HOME=/opt/hyperion/common/JRE/Sun/1.5.0
export HS_JAVA_HOME
HYPERION_HOME=/opt/hyperion
export HYPERION_HOME
PLN_JAR_PATH=/opt/hyperion/Planning/lib
export PLN_JAR_PATH
PLN_PROPERTIES_PATH=/opt/hyperion/deployments/Tomcat5/HyperionPlanning/webapps/HyperionPlanning/WEB-INF/classes
export PLN_PROPERTIES_PATH
CLASSPATH=${PLN_JAR_PATH}/HspJS.jar:${PLN_PROPERTIES_PATH}:${PLN_JAR_PATH}/hbrhppluginjar:${PLN_JAR_PATH}/jakarta-regexp-1.4.
jar:${PLN_JAR_PATH}/hyjdbc.jar:${PLN_JAR_PATH}/iText.jar:${PLN_JAR_PATH}/iTextAsian.jar:${PLN_JAR_PATH}/mail.jar:${PLN_JAR_PA
TH}/jdom.jar:${PLN_JAR_PATH}/dom.jar:${PLN_JAR_PATH}/sax.jar:${PLN_JAR_PATH}/xercesImpl.jar:${PLN_JAR_PATH}/jaxp-api.jar:${PL
N_JAR_PATH}/classes12.zip:${PLN_JAR_PATH}/db2java.zip:${PLN_JAR_PATH}/db2jcc.jar:${HYPERION_HOME}/common/CSS/9.3.1/lib/css-9_
3_1.jar:${HYPERION_HOME}/common/CSS/9.3.1/lib/ldapbp.jar:${PLN_JAR_PATH}/log4j.jar:${PLN_JAR_PATH}/log4j-1.2.8.jar:${PLN_JAR_
PATH}/hbrhppluginjar.jar:${PLN_JAR_PATH}/ess_japi.jar:${PLN_JAR_PATH}/ess_es_server.jar:${PLN_JAR_PATH}/commons-httpclient-3.
0.jar:${PLN_JAR_PATH}/commons-codec-1.3.jar:${PLN_JAR_PATH}/jakarta-slide-webdavlib.jar:${PLN_JAR_PATH}/ognl-2.6.7.jar:${HYPE
RION_HOME}/common/CLS/9.3.1/lib/cls-9_3_1.jar:${HYPERION_HOME}/common/CLS/9.3.1/lib/EccpressoAll.jar:${HYPERION_HOME}/common/
CLS/9.3.1/lib/flexlm.jar:${HYPERION_HOME}/common/CLS/9.3.1/lib/flexlmutil.jar:${HYPERION_HOME}/AdminServices/server/lib/easse
rverplugin.jar:${PLN_JAR_PATH}/interop-sdk.jar:${PLN_JAR_PATH}/HspCopyApp.jar:${PLN_JAR_PATH}/commons-logging.jar:${CLASSPATH
export CLASSPATH
case $OS in
HP-UX)
SHLIB_PATH=${HYPERION_HOME}/common/EssbaseRTC/9.3.1/bin:${HYPERION_HOME}/Planning/lib:${SHLIB_PATH:-}
export SHLIB_PATH
SunOS)
LD_LIBRARY_PATH=${HYPERION_HOME}/common/EssbaseRTC/9.3.1/bin:${HYPERION_HOME}/Planning/lib:${LD_LIBRARY_PATH:-}
export LD_LIBRARY_PATH
AIX)
LIBPATH=${HYPERION_HOME}/common/EssbaseRTC/9.3.1/bin:${HYPERION_HOME}/Planning/lib:${LIBPATH:-}
export LIBPATH
echo "$OS is not supported"
esac
We have not made any changes to either the shell or 'CubeRefresh.sh' or 'setHPenv.sh'
From the past couple of days the shell that executes 'CubeRefresh.sh' has been failing with the error message below.
Cube refresh failed with error: java.rmi.UnmarshalException: error unmarshalling return; nested exception is:
java.io.EOFException
This error is causing our Essbase cubes to not get refreshed from Planning cubes through these batch jobs.
On the other hand the manual refesh from within Planning works.
We are on Hyperion® Planning – System 9 - Version : 9.3.1.1.10
Any help on this would be greatly appreciated.
Thanks
Andy
Edited by: Andy_D on Jul 30, 2012 9:04 AM -
At DI R3trans fails with this error code ORA-12545, but CI runs
Hello Gurus,
We have our BW System on two instances with a separated oracle database server.
Last week the system was unreachable and we must restarted it hard.
After that, the Listener could started and runs. The DB could started, mounted and opened successfully.
Now we have a special problem.
The central instance can connect at startup to the database. But the dialog instance not.
The DI get the following error:
|> R3trans -x
This is R3trans version 6.14 (release 701 - 12.06.09 - 15:20:00).
2EETW169 no connect possible: "DBMS = ORACLE --- dbs_ora_tnsname = 'BW2'"
R3trans finished (0012).
The trans.log entry are:
4 ETW000 [dbsloci. ,00000] *** ERROR => CONNECT failed with sql error '12541' 17 0.187511
4 ETW000 [dev trc ,00000] set_ocica() -> SQL error code 12541 13 0.187524
4 ETW000 [dev trc ,00000] -->oci_get_errmsg (con_hdl=0, rc=12541) 14 0.187538
4 ETW000 [dev trc ,00000] OCIErrorGet -> SQL error code: 12541 14 0.187552
4 ETW000 [dev trc ,00000] ORA-12541: TNS:no listener
4 ETW000 22 0.187574
4 ETW000 [dblink ,00433] ***LOG BY2=>sql error 12541 performing CON [dblink#4 @ 433] 14396 0.201970
4 ETW000 [dblink ,00433] ***LOG BY0=>ORA-12541: TNS:no listener [dblink#4 @ 433] 39 0.202009
2EETW169 no connect possible: "DBMS = ORACLE --- dbs_ora_tnsname = 'BW2'"
A telnet connection test to port 1527 are also unsuccessful.
But sporadicly the telnet or R3trans connection are successful, but the second check are unsuccessful.
We have checked the telnet connection to another oracle database server (ERP) at port 1527 and it works.
The CI have some entry's in ST22 with DBIF_RSQL_SQL_ERROR --> ORA-03114: not connected to ORACLE.
Are someone known something about this issue?
regards
Chris@ Sunny Pahuja:
We checked sapmnt.
Sapmnt is common on CI and DI. It was never mounted on DB. But DB runs perfectly until this issue.
@ Ankit Gupta
We checked the configuration of listener.
It is the same like the listener configuration of our ERP system with CI, DI and DB on separate Servers, too.
@ Rajesh Narkhede
From DB Server
|> tnsping BW2
TNS Ping Utility for IBM/AIX RISC System/6000: Version 10.2.0.2.0 - Production on 06-MAY-2010 07:40:56
Copyright (c) 1997, 2005, Oracle. All rights reserved.
Used parameter files:
/oracle/BW2/102_64/network/admin/sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (COMMUNITY = SAP.WORLD) (PROTOCOL = TCP)
(HOST = bw2dba) (PORT = 1527))) (CONNECT_DATA = (SID = BW2) (GLOBAL_NAME = BW2.WORLD)))
OK (100 msec)
On CI and DI we don't have tnsping.
Just copy it don't work.
|> tnsping BW2
TNS Ping Utility for IBM/AIX RISC System/6000: Version 10.2.0.2.0 - Production on 06-MAY-2010 08:39:17
Copyright (c) 1997, 2005, Oracle. All rights reserved.
Message 3511 not found; No message file for product=network, facility=TNS
Message 3512 not found; No message file for product=network, facility=TNS
Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (COMMUNITY = SAP.WORLD) (PROTOCOL = TCP)
(HOST = bw2dba) (PORT = 1527))) (CONNECT_DATA = (SID = BW2) (GLOBAL_NAME = BW2.WORLD)))
Message 3509 not found; No message file for product=network, facility=TNS
How to get it on the CI and DI. In the SAR files at SAP it is not included. I can't found something in the Web. -
i ve updated my i pod touch to version 6.0.1. Installation got failed with some error msg, and now my i pod is not getting detedted in my system.Help me to fix it up.
What's the error mesage?
-
The installation of SAP Front-End components failed with 95 errors.
I tried to install SAP GUI 7.20 on Windows Vista X64. And I got this error message:
The installation of SAP Front-End components failed with 95 errors.
This 7.20 version used to run on this operating system fine. I reinstalled the OS, and now I got this.Hi,
I suppose you reinstalled the same OS.
Did you install the JSDK (java) afterwards. As you must be aware Java is a pre-requisite for the SAP Frontend.
Also make sure you have set the environment variables after installing java.
Further documentation, the SAP installation manual can be found in the u201CDOCUu201D folder of the installation software.
Regards,
Rohan. -
IDoc failed with the error massaeg "Instance of object type could not be ch
Hi All
I am getting IDoc failed with the error massaeg "Instance of object type could not be changed"
Message type :PORDCR
Basic type : PORDCR05
Message no. BAPI003
Status : 51
All POs are get uploaded in SAP during Cut over activities only.
Please suggest on this.It will be a great help.
Thanks
AjitHi
After uploading POs into SAP we are changing quantity and value in PO in Legacy system, and for this all IDocs are failed, subsequently these changes are not triggering to ECC.
Please help
Thanks
Ajit -
External Drive Disk Erase Failed with the Error Input/Output Error
I have 2 hard drives in an external FW800 enclosure that I am unable to format. When I go to initialize the drives in Disk Utility, I get the following error message: "Disk Erase failed with the error: Input/output error."
The drives show up in Disk Utility, but I can't repair them (that option is grayed out). Disk Utility correctly ID's the manufacturer of the drives (Maxtor), their size (200gb each), so it's obviously seeing that the drives are there. But it won't let me format them.
The drives are new, by the way; they don't have any data/files on them. I have Disk Warrior, but the drives don't show up there to be repaired -- probably because they aren't formatted yet.
After looking at other posts, I tried switching the jumper settings around on the drives -- from Master/Slave to cable select and back again, but it didn't help. I also tried doing a zero erase (even though the drives are new), zapping the PRAM -- again, no help.
One question I had is whether this could be a bad FW800 cable? The cable is new -- it came with the enclosure, which is an OWC Dual FW 800 enclosure. Other than that, does anyone have any other thoughts about what's causing this? Any help would be greatly appreciated.
MatthewSOLUTION!!!!
I had the exact same problem. I have the original 20 GB hard drive that came in my Powerbook G4 550MHz and a couple of years ago I traded up for a 60 GB drive and bought a FW/USB enclosure for my original drive to use it to backup my important files. I hadn't backed up in over a year (shame on me!) and I decided maybe I should erase the drive and start from scratch. It was connected via USB.
At that point DiskUtility gave me the exact same Input/Output error. I tried partitioning the drive into 1 or more partitions but came up with the same error. I couldn't figure out what was wrong so I decided to startup in OS 9.2.2, I did that and let it start up, then plugged in the hard drive and it gave me the standard "This disk is unrecognizable, do you want to eject or erase?" so I clicked Initalize. It worked!
Just make sure you choose the MacOS Extended option when initializing out of OS 9 (instead of the MacOS Standard option) so it can be read and viewed in OS X.
If your computer is too new to be able to boot from an OS 9 folder on your drive or an OS 9 CD, then see if a friend or a local library has older computers that are running OS 9 or can boot from it. If not let me know and you can send me your drive and I'll reformat it.
Kind of crazy...I haven't used the OS 9 partition on my HD in YEARS...was even thinking about erasing it since I don't use any Classic applications anymore...good thing I didn't!
Nick
Powerbook G4 550Mhz Mac OS X (10.4.6)
Maybe you are looking for
-
Hi, I have trouble with the ROWID (ORA-01445) error when running the standard doQuery function on a button in a Form. Is it possible to use doQuery or do I have to write my own PL/SQL code, if so where can I find information on this (like the code fo
-
Fillable forms come back BLANK mainly from Mac Users
Hello, I created a fillable form from scratch in Adobe Acrobat 9 Pro Extended version 9.3.2, using Adobe Livecycle Designer ES version 8.2.1. I'm on Windows XP. When I first created the form I saved it on the company server, but, I can't remember w
-
Finally, activation success! Here is what worked for me:
After 38+ hours I bought 2 iPhones. For both of them I was porting a number over from Sprint (from the same account). Selected the Family plan for activation. Within an hour, the first iPhone was activated for all but incoming calls (My wife's phone)
-
I am experiencing a significant problem with my download of PS CS6, and am unable to find a solution online. After download there is a message that some files failed to load. I am unable to find out which files. After opening Photoshop and Bridge, t
-
I still have the original phone and with O2 I am entitled to a FREE 3G phone. My dilemma is - Do I get the 3G phone and pay nothing or do I spent nearly £90 for the 3G S. Any advice?