RAID-Exsisting HDD- KT4 Ultra

I am trying to connect two identical HDD to my RAID serial ports. I have loaded the drivers in Windows XP. They show up with the code 10 in device manager. I have tried uninstalling and re-installing. The RAID bios is not showing up in the POST so I cannot set an array. I now am connect with the new drive to RAID 2 and the system drive to IDE 1. I want to connect both to RAID and set for Array 1- Protection. I have read a lot on RAID here but all seem to be new installations. I have the lastest RAID drivers and Bios.

I'm glad to hear that your problem is solved, consider yourself lucky!!!! I tried what you did and unfortunately it didn't work for me ;( :
After getting the critical error during initial array creation, I continued to boot but no RAID entry appeared as a choice in the BIOS boot sequence.
However, W2k seemed to find the array anyway and tried to boot. After the graphical Win 2000 start screen it blue screened with a message like STOP IRQ not less than or equal. It said if this was the first time this screen has shown, restart the computer.
After restarting the computer is blue screened again, this time with the message STOP Unknown Hard error
After this I tried restarting again, entering FastBuild, and attempting to rebuild the array. During array rebuild, it failed giving the same critical error, with the source (Windows) drive.
Was your critical error with the Windows (source) drive, or the new one? How do you have your array partitioned and what filesystem(s) are you using? I have one 7GB primary partition and the remainder on an extended partition, both NTFS.
Thanks,
Danny

Similar Messages

Raid BIOS Gone (KT4 Ultra-BSR)

I recently bought a Serial ATA Hard Drive wanting to install it on the raid controller. But when I went to enter the Raid Controller's BIOS FastBuild Setup (at boot-time), it never shows up.
I have the KT4 Ultra-BSR, and I can see the RAID Controller enable/disable option in the Integrated Peripherals. I have it enabled, but it NEVER displays the RAID bios at boot-up. This is the second KT4 Ultra I've had and I know I saw the RAID bios on the first one I had. I have the latest system BIOS installed (1.30).
Has anyone experienced this and/or know how to fix it? Is there a way for flash the RAID controller to possibly fix it? Did the entry to the setup change from whats in the manual (ctrl-F4)?
Any help is greatly appreciated. Thanks

I've seen a couple other post like yours Shark. While that makes me feel a little more comfortable that other are having similar problems, I thinks mine's a little different. I don't ever remember seeing the RAID BIOS on this motherboard. I've tried turning it off and on in a row to see if mine would eventuall show, but I never see it.
Does anyone from MSI read these? I think something should be done.

Raid & KT4 Ultra BSR

;( Can anyone save my sanity!
Read all about updating PC, thought easy, I can do that. During summer fitted extra memorey 512, fitted new hard drive, then an extra one for back ups, all well so far, then at Christmas bought KT4 Ultra BSR board & AMD 2400XP. Fitted ok no probs, great.
So why can't I understand how the hell to get Raid to work. The guide is about as useful as a smack in the mouth. Can anyone point me in the right direction to get an easy to understand guide to which HDD connects where and what I do with the jumpers on each. Tried configuring as Master and Slave on same cable to IDE 1 works Ok. Then tried same on IDE 3 only MAster shown and cannot configure raid. Please help before I trash it!

hi,
i had the same problem,
i have pull the little white mini plug of the harddisk where you can put it on master/save/..........
that restarted my compu and in to the set actived the raid / serial controller.
than you niet to configure your harddisk ( push ctrl-f)
and than you use nr.1 (auto........).
restart and normaly is the job al done.
jupliner/belgium.
mb: msi kt4 ultra bsr
cpu xp 2200.
256 mb/ddr/333mhz
big tower
geforce2
western digital 80gb/7200(8mb cache)
liteon 52x24x52
16/48 dvd

KT4 Ultra (6590) need update of the Promise SATA RAID Controller PDC20376

The last Bios update AMI 1.4 for the KT4 Ultra (6590) have built in the bios version 1.00.0.18 for the PDC20376 (Promise 376).
I can configure 2 maxtor (6E040T0) sata1 in a raid0 array and it works under WinXP SP3,
but the 2 drives are working in UDMA5 according to the FastBuild Utility when the motherboard specifications talks about 150Mb (SATA1).
It's not an OS problem because the FastBuild Utility at Bios startup show the UDMA5 mode for HDD.
It's not a Maxtor 6E040T0 (SATA1) problem because have no jumper to set.
The Promise support center don't provide support for built in raid controller but the responce was that it's related to a known bios issue of the controller, so i have to update.
For the last Bios version for the S150 TX4 controller look at:
http://promise.com/support/download/download2_eng.asp?productId=108&category=all&os=100&go=GO
It's impossible to update the bios with the promise tool because the controller is integrated in the motherboard.
I read for example than on the motherboard K7N2 Delta-ILSR the bios version of the Promise 376 controller is 1.00.0.21:
https://forum-en.msi.com/index.php?topic=92756.msg665966#msg665966
I think the only solution is a modding bios, where i have to replace only the Promise controller bios but:
1) The tool amibcp.exe can't open the A6590VMS.140 AMI bios (renamed .rom), i don't know why!!!
2) What promise controller bios rom file is good?
Can anyone out there help . . . please ?

This is my results compared to my other UDMA6 HDD on IDE1, HDTach long bench stop with "Read Error" and only quick bench works.
The version of the Controller driver under WinXP-SP3 is 1.0.1.29 and I configured the driver in the PAM Utility with:
"Driver Write Cache" enabled and "Write Back" as cache settings (The 2 Maxtor SATA1 in RAID have 2MB of cache, but i don't know How many cache have the controller!!).
The Burst Speed is too strange!!! quick bench error?
I made it so your image is clickable.
-Frankenputer

KT4 ULTRA / Promise Fasttrack TX2 100 RAID problems

I have my decided to retire my old MAXTOR and get 2 WD800JB for my new Promise Fasttrack TX2 100 RAID card. I set the RAID and stuff up everything is working fine but first I realized that my RAID benchmarks are low. I tried different stripe sizes(16/16 - 64/64), drivers and even tried both drives independent on different chanels RAID card.
I was still using old installed OS from my old HDD and I decided to install new OS on RAID 0 array and see how fast it boots up. I installed windows properly no problems but when I restart the system without WinXP CD in the CD drive RAID card did not boot up, I was getting an error message saying "error booting from the previous device" but when I put WinXP CD back in after cd boot screen it boots from RAID drives.
My RAID System;
KT4 ULTRA SR
Promise Fasttrack TX2 100
2 x WD800JB
here is my question; do you guys know any issues between KT4 ULTRA and Promise TX2 card. If no I'll get another card and see if there is sth wrong with this one.
btw my system is working fine!!!!

1 got the wd drives either jumperless........stand alone master or cable select
on the black end of the ide
2 have you set scsi second to cdrom in bios boot order
3 never have any other hard drives connected in the box when installing raid either

KT4 Ultra "RAID?" controller

The S-ATA and ATA133 Promise controller on KT4 Ultra
1)Is it a RAID or an ATA (and S-ATA) controller?
2)Does it have RAID 0 performance level with ATA133 HDDs, same as that of the KT3 Ultra 2 RAID Controller, or it is just a RAID for S-ATA HDDs?

Good, that's what I wanted to hear actually. While I never admired the RAID controllers I got comfused when I say the FILE SYSTEM BENCHMARK in Sandra 2003 saying that RAID level 0 is a lot faster than NON-RAID, givving a bandwitch of about 45Mbyte/sec to 8MB cache 80GB HDD in NTFS WINXP, compared to quite less without the use of RAID. In my NTFS WINXP with NO RAID it counted 30MByte/sec on the 80GB 8MB cache WD HDD. The disk transfer rate that I did count in pure format was counted at 45Mbyte/sec

RAID not happenin with my drives on KT4 ultra SR

been thru most of the forum n the FAQ ...n learnt that my mobo MSI KT4 ultra SR' RAID thingy wont support my 40gb (7200)-existin n the new drive i bought a week ago (80gig 7200) hopin to get them up on RAID....bought this mobo for the lone RAID feature!!!!!!

my rig specs:
AMD ATHLON XP 2000+
MSI KT4 ULTRA SR
512mb 2700 MICRON DDR
GFORCE 4mx 440SE 128 DDR
40 gb 7200 n 80 gb 7200 SEAGATE HDD's
300w PSU - local one
LG 16x DVD ROM
LG 52x CRW
17" LG
CREATIVE INSPIRE 4.1
WINXP SP1a
Quote
Please give complete PC specs, includding P.Su.brand and AMPS. it gives to 3.3v. 5v. and 12v
if im not right the info is grabbd from PC alert:
3.3v - 3.07 , +5v - 4.70 , +12v - 12.48 , vcore - 1.60
Quote
What kind of RAID? If you want RAID 0 (striped)
im lookin at RAID O but i believe n from what i have learnt from the posts here is that i need SATA drives to have RAID goin for me!!!??

KT4 Ultra(6590) over 13 Gb Boot HDD problem

I am stumped...Completely...
I have a KT4 Ultra I am setting up with 512 ram, AMD 1.3 gig XP, WinXP Pro, blah blah, all works fine...But it will not recognize a HDD larger than 13 Gb as master but will as slave.
I have tried numerous drives. It boots to a black screen with a blinking cursor.
Here is the drives that work as primary:
IBM Deskstar 13.6 Gb and a WD313000 13.2 Gb..Both load up fine..
Now I have these drives with operating systems and all, that just go to a cursor:
2 different 40 gb Seagate ST340810A, and a 20 Gb WD200
all work as slave drives and full capacity shows..I do not want my slower and smaller 13 gb to be my primary master.
Also they are not recognized as master in IDE3.
Please help!!!!!!!

I am not going to worry much over the PSU, my comp seems to run pretty cool.
Anyways I solved the boot problem and it was not the IDE cable backwards or jumper locations. It was because the drives i was trying to boot from were secondary drives on a dual boot system, i just did advanced install on the new drive and tried using that drive as master. Both 40 gigs are now working...Lesson learned. I am not an expert, but i am getting there
Now i have to figure out the IDE RAID thingie..I know there is already a host of info on it so i will do a search.
Thank you all for your help, and I will probably be here again with something or another, lol.

KT4 Ultra: problem config. raid array IDE3

I owe the MSI 6590 KT4 Ultra BSR mainboard and I have difficulties configurring the RAID array in striping mode, on the IDE3 controller.
The manual describes on page 2-18 it's possible to connect up to 2 hard drives, cdrom, 120mb fd and other devices to the IDE3 controller.
Unfortunately only one of my two MAXTOR D740X-6L (6L080J4) 80gig drives is recognized by the array.
One Maxtor hard drive is jumpered as MASTER and the other is set up as SLAVE.
When I hook up the cable to an ordinary IDE port (eg IDE1) the two drives are properly recognized.
Both drives can be formatted using the regular IDE ports, this means without any cluster errors or other errors so the drives are physically OK.
Before I wrote this post I checked the support section again to make sure I am using the latest BIOS which is 1.1. I also downgraded to 1.0, but that didn't solve my problem either.
Since I work in a computer shop now and then I had the opportunity to check two Maxtor Fireball3 30gig drives on a different MS-6590 RAID board (BIOS 1.1.) and exactly the same problem occurs: the 2nd drive won't be recognized in the ARRAY on IDE3.
Please tell me what to do to make the striping option fully work on my two IDENTICAL Maxtor hard drives since MSI support came up with a standard email, which didn't cheer me up at all. Hopefully this time they will investigate this matter since no doubt more people will experience this.

Thanks for the quick response, though it's not satisfactory for me (of course).
Actually before installing the new KT4 Ultra I owed the KT266 Pro RAID motherboard. It's true this board has two controllers for the RAID option. Nevertheless because after reading the manual of this new board I was convinced I could connect two hard drives on the IDE3-channel. This is the reason I decided to go ahead and to upgrade to this new mainboard.
I guess I have to go back to my employer and fall back again to my KT266 (MS6380).

Kt4 ultra bios and raid function

i am using the kt4 ultra motherboard (bluetooth ready and SATA), when i go to the integrated peripherals, onboard pci controller i can only enable/disable the audio controller....
where am i supposed to enable/disable the raid controller?? is there a jumper i am missing on the board?
thanks in advance,
brian

Are you sure you have a KT4 ultra with the Serial ATA/RAID controller option? There are several versions of the motherboard, all doesn't include the PDC20376 SATA/RAID controller, please check if you can find the chip on your mobo. The controller is enabled/disabled under Integrated Peripherals->OnBoard PCI Controller
->Serial ATA controller.

KT4-Ultra - RAID

Hi,
Two questions about the controller Promise 20376 of the KT4 Ultra:
- is there a way to set a trip size below 16ko? (I4ve 16, 32, 64, 128 and 256ko).
- is there a way to update the bios of the RAID controller ... if yes .. how ?
Thanks for any help

nah converters can be obtained here in Holland, in fact I have such converter.
It is working properly at least when my RAID is being detected by the kt4 mobo. Then fastrak376 does show up and on next boot it doesn't. Nope it not nothing to do with the converter since hooking one hard drive up to IDE3 results in the same problems.
Messing with the BIOS settings works properly from time to time, since I was able to install WinXP properly. Will continue this weekend putting some more grease on my 2000+ cpu so I can run at full speed (133fsb) and then last but not least finding out what the problem might be concerning the RAID issue, to me it is a buggy BIOS for some reason since this SERIAL ATA RAID option is faded out in the BIOS from time to time .. ?( .. Just like when you put an AGP 8x card in the mobo then the AGP 2x / 4x speed vanishes too, but that is understandable .. blah anyone to help? ..

Sata Raid problems with MSI KT4 Ultra Via kt400 chipset

ok i am having major problems setting up my sata raid in my brothers msi KT4 Ultra via KT 400 chipset
it comes up with my irq settings are wrong
my hard drives are WD 120 GB 7200rpms SATA - sold my mobo asus A7N8X - Delux and used my bros mobo above but just cant get them to work if ne one has ne idea on how to fix it (bios is still factory default do i have too flash it to get it too work etc)
would help lots thanx

you dont need multiple threads on the same thing

KT4 Ultra Raid Setup

Ok I want to set up a raid set for performance and am lacking an understanding of the setup.
Here is my configuration:
MSI KT4 Ultra w/Raid
GF4 4200 Ti
AMD Athlon 2100+
2x 256 333MHz Generic RAM
Intel Pro 100 Management Adapter (LAN)
2x 10 Gig Maxtor ATA100 5400 RPM HD's
1x 60 Gig Maxtor ATA100 7200 RPM HD
1 CDRW
1 52x CDROM
This is what I have tried
Put 1 10 gig drive on Primary IDE as master w/ 60 gig as slave
Both CD's on Secondary IDE
1x 10 Gig on RAID Controller (onboard)
When I go into the fast track utility and autoconfigure for performance its shows as only having one drive in the array. In the setup guide it shows that option as 2 drives in the array.
Is there something wrong with my setup?
Why does only one drive show up in the array?
I havent installed an OS yet but it will be 98.
The main drive on Primary IDE has been partitioned with Fdisk as a single active partition and nothing has been done with the second. It's my understanding it will be built when the raid is functioning, is this right?
Thx in advance for your time. Great forum by the way. Cheers to the techies witht he answers. Incidentally i'm not a newbie with comps just with RAID so technical is fine.

KT4 Ultra
Thx for the response guys.
I understand that I may only use one drive with the IDE3. My board does have 2 serial ata connectors on it as well.
If I only use the IDE3 with one hard drive will the mirror work correctly if I use the same drive (same model specs etc) on the primary ide and use my 60 gig as a secondary drive on the primary as well (i know the 60 will not work with the mirror) All i want is the performance increase for now until the serial drives drop in price and become more readily available.
So my config would be as follows:
1 12 gig drive on pri ide as master
1 60 gig on pri ide as slave
1 12 on ide3 for mirror.
If i use this will i get increased performance as far as load times etc?

KT4 Ultra Promise Raid Problem

Hi,
I recently purchased a KT4 Ultra board to replace a K7T 266 board. After connecting my RAID 0 array to the 40pin IDE RAID controller on the new board, I was surprised to discover that only one hard drive was recognized. I tried every jumper combination, even iterating through ones I knew would be invalid. I switched cables, and I even tried a different hard drive. Since the two Serial ATA connectors naturally only support one drive, I would hope that some errata in the BIOS would not cause the old 40pin connector to only allow one drive. Who knows.. that was my only guess, as I've tried everything I can think of. Does anyone have any ideas?
Thanks,
Jeremy

ide 3 acts like a sata channel and will read one drive only
as it says on boards page you need at least one sata drive for raid
you cheapest option is 2x sata convertors
abit make them and sig do as well
i say 2 as i would not have one sata one ide in raid myself
ps this is the nforce forum not via

KT4 Ultra and SATA

I have a KT4 Ultra that supports SATA Raid and Im looking at getting a new HDD. CAn I run my old PATA HDD with a SATA HDD without it being in raid format or do the disk have to be in a raid format.

Hey guys, how about this:
MSI KT4 Ultra SR, Win2000, PDC 20376 Promise Serial ATA chip on board. WD 40gig IDE hd as primary on IDE 1. Attached a Maxtor 120gig SATA to the Serial ATA 1 connector. While booting did NOT setup an array. Windows 2000 in Disk Management under Device Manager/Disk Drives has now two folders, one for the WD and one that says SCSI Disk Device. It's also also recognized under System Information/Components/Storage as SCSI controlled by the Fast Track 376 controller. Is this a proper way to setup the serial Maxtor as an extra single drive in the system attached to the Serial interface? Is this even possbile? My problem is that while the drive is recognized as a SCSI disk device as described above, it is NOT seen under Disk Management as a new unformatted drive with a new letter. Assuming the above setup is correct, how do I format the drive so Windows can use it? Any help will be greatly appreciated, thank you.

RAID-Exsisting HDD- KT4 Ultra

Similar Messages

Maybe you are looking for