RAID Mirror failed - help interpreting error code?
Hi all - I run the primary disk mirrored on my Dual 2.0 Xserver (10.4.7) using Apple's software RAID. No problems for two years, but found this am a warning on System Monitor, showing my RAID as degraded - one disk had dropped out of the set. All functions continued forward without interruption.
Here's all the system log has to say:
Aug 12 18:29:34 mail kernel[0]: AppleRAID::completeRAIDRequest - error 0xe00002ca detected for set "Xserver80G" (9477A440-E50F-11D9-B65B-000D939C5BEC), member E612F8B0-3082-4222-A9FE-B58D35CDA3B8, set byte offset = 907558912.
Aug 12 18:32:39 mail kernel[0]: AppleRAID::recover() member E612F8B0-3082-4222-A9FE-B58D35CDA3B8 from set "Xserver80G" (9477A440-E50F-11D9-B65B-000D939C5BEC) has been marked offline.
Aug 12 18:32:39 mail kernel[0]: AppleRAID::restartSet - restarting set "Xserver80G" (9477A440-E50F-11D9-B65B-000D939C5BEC).
The System Monitor shows no pre-failure warnings on the HD's themselves, and I'm assuming there was an error in the mirroring, and the RAID software gracefully dropped the offending volume.
My questions are: Any help interpreting the error code so I can narrow down the likely cause, if any? any ideas what causes this kind of error? Is it likely to recurr?
Any help much appreciated. I'll be rebuilding the set tomorrow after working hours.
The RAID set got out of sync. You might see this from time to time if you use Apple's raid driver.
Take a look at softraid.com for a better driver.
Similar Messages
-
I cannot get Elements 13.1 to download completely. I have 3 different case numbers from Adobe and nothing helps. I always get the "download failed" and the error code u44m1i210. I would either like to get the product downloaded or eliminate the constant attempt which just ties up my computer.
You could try the direct download links here
Adobe Photoshop Elements 13 Direct Download Links, Premiere too | ProDesignTools
And here is some info on that error code
Error U44M1I210 | Install updates -
Help, creative desktop failed to install error code 1000
I just subscribed for the creative cloud and when I try to install the app it fails with the error Creative Dekstop failed to install error code 1000. Can some one shed any light on how to resolve this
ThanksLink for Download & Install & Setup & Activation may help
-Chat http://www.adobe.com/support/download-install/supportinfo/ -
Acrobat XI quit working. I uninstalled it then went to Creative Cloud to reinstall CC failed to reinstall Error code 50 help
Thanks for your help. I finally just called Adobe and they fixed it
quickly by doing stuff that was clearly over this old man's head.
W. Mercer Dye
<Removed by Moderator>
CONFIDENTIAL NOTICE : If you have received this email in error, please
immediately notify the sender by email at the address shown above. This
email may contain confidential or legally privileged information that is
intended only for the use of the individual or entity named in this email.
If you are not the intended recipient, you are hereby notified that any
disclosure, copying, distribution or reliance upon the contents of this
email is strictly prohibited. Please delete from your files if you are not
the intended recipient. Thank you for your compliance.
On Mon, Nov 17, 2014 at 10:51 AM, Jeff A Wright <[email protected]> -
The system failed to merge, error code : General Access denied
The system failed to merge, error code : General Access denied. Could anyone help me on this
Hi,
It could be several things, I think it could be a good start with the following page:
https://blogs.technet.com/b/chrad/archive/2009/10/02/differencing-disks-merging-80070005-error-just-one-persons-lesson-learned.aspx
If that doesn't help you could check out the following technet page to see if it is a permission problem. (it is not exactly the same problem but one of our customers once had the same problem and we solved it with the follwing KB:http://support.microsoft.com/kb/2249906/en-us
Hope this helps you out. -
Install OCS 10.1.2 Infra DB failed with LDAP: error code 16 on Workspaces
during install OCS Infrastructure DB OCS have error:
... processed key-value: logfile=/oracle/product/dbocs/workspaces/logs/cw_config_backend.log
... processed key-value: action=setup_backend
... processed key-value: oh=/oracle/product/dbocs
... processed key-value: oid=oid.domain
... processed key-value: oid_port=389
... processed key-value: oid_user_dn=cn=orcladmin
... processed key-value: oid_passwd=xxxxxx
... processed key-value: db_sn=ocs.domain
... processed key-value: dba_user=sys
... processed key-value: dba_passwd=xxxxxx
... processed key-value: cw_db_passwd=xxxxxx
Attempting to set logfile to: /oracle/product/dbocs/workspaces/logs/cw_config_backend.log
Processed oh=/oracle/product/dbocs
BACKEND installation ...
... Trying to lookup database dn
... Obtain OID connection
...... Can not obtain OID ssl port.
...... OID port = "389"
...... Trying to establish a non-ssl connection. OID host "oid.domain", OID port "389", OID user dn "cn=orcladmin".
... OID connection created.
...... You must specify either db_dn or db_sn.
...... ldap search filter "(&(objectclass=orcldbserver)(orcldbglobalname=ocs.domain))"
...... Succesfully located database dn "cn=ocs,cn=OracleContext".
...... Database dn = "cn=ocs,cn=OracleContext"
... Validating existence and version of CW schema: "CWSYS" in database: "cn=ocs,cn=OracleContext".
... Obtain JDBC connect string
... JDBC connect string = "(DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=ocsoas.domain)(PORT=1521))(CONNECT_DATA=(SERVICE_NAME=ocs.domain)))"
...derived: "jdbc_str=(DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=ocsoas.domain)(PORT=1521))(CONNECT_DATA=(SERVICE_NAME=ocs.domain)))".
Opening JDBC connection: "jdbc:oracle:thin:sys/xxxxxx@(DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=ocsoas.domain)(PORT=1521))(CONNECT_DATA=(SERVICE_NAME=ocs.domain)))"
Opening JDBC connection: "jdbc:oracle:thin:sys/xxxxxx@(DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=ocsoas.domain)(PORT=1521))(CONNECT_DATA=(SERVICE_NAME=ocs.domain)))"
Unlocking schema and setting passwd: "CWSYS/xxxxxx".
Opening JDBC connection: "jdbc:oracle:thin:sys/xxxxxx@(DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=ocsoas.domain)(PORT=1521))(CONNECT_DATA=(SERVICE_NAME=ocs.domain)))"
... Checking Workspaces container.
... Container "cn=CollaborativeWorkspaces,cn=Products,cn=OracleContext" already exist.
... Finish checking Workspaces container.
... Trying to create backend application entity in OID
...... Database dn = "cn=ocs,cn=OracleContext"
...... Backend entity name = "ocs"
...... Backend entity dn = "orclApplicationCommonName=ocs,cn=Database Instances,cn=CollaborativeWorkspaces,cn=Products,cn=OracleContext"
... Backend entries already exist. Cleanup old entries.
deregisterProvisioningListener ...
app dn = orclApplicationCommonName=ocs,cn=Database Instances,cn=CollaborativeWorkspaces,cn=Products,cn=OracleContext
subscriber = dc=domain,dc=com
... Trying to remove entity "orclApplicationCommonName=ocs,cn=Database Instances,cn=CollaborativeWorkspaces,cn=Products,cn=OracleContext".
... Deleting "orclApplicationCommonName=ocs,cn=Database Instances,cn=CollaborativeWorkspaces,cn=Products,cn=OracleContext"
Adding Workspaces application entity to: cn=Service Registry Viewers,cn=Groups,cn=OracleContext
Adding Workspaces application entity to: cn=Service Registry Admins,cn=Groups,cn=OracleContext
... Insufficient privilege to create application entity "orclApplicationCommonName=ocs,cn=Database Instances,cn=CollaborativeWorkspaces,cn=Products,cn=OracleContext". Please check the user DN and password.
javax.naming.directory.NoSuchAttributeException: [LDAP: error code 16 - One or more values for attribute uniquemember does not exist]; remaining name 'cn=Service Registry Admins,cn=Groups,cn=OracleContext'
at com.sun.jndi.ldap.LdapCtx.mapErrorCode(LdapCtx.java:3009)
at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2934)
at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2740)
at com.sun.jndi.ldap.LdapCtx.c_modifyAttributes(LdapCtx.java:1373)
at com.sun.jndi.toolkit.ctx.ComponentDirContext.p_modifyAttributes(ComponentDirContext.java:235)
at com.sun.jndi.toolkit.ctx.PartialCompositeDirContext.modifyAttributes(PartialCompositeDirContext.java:147)
at com.sun.jndi.toolkit.ctx.PartialCompositeDirContext.modifyAttributes(PartialCompositeDirContext.java:136)
at javax.naming.directory.InitialDirContext.modifyAttributes(InitialDirContext.java:136)
at oracle.workspaces.share.util.oid.OIDShareUtil.setEntryAttribute(OIDShareUtil.java:471)
at oracle.workspaces.share.util.oid.OIDShareUtil.addMemberToGroup(OIDShareUtil.java:420)
at oracle.workspaces.share.util.oid.OIDShareUtil.addMemberToGroupIgnoreDuplicateMember(OIDShareUtil.java:435)
at oracle.workspaces.install.CwConfigOID.createBackendEntity(CwConfigOID.java:1205)
at oracle.workspaces.install.CwConfigOID.registerBackend(CwConfigOID.java:449)
at oracle.workspaces.install.CwConfig.regBackend(CwConfig.java:320)
at oracle.workspaces.install.CwConfig.run(CwConfig.java:609)
at oracle.workspaces.install.CwConfig.main(CwConfig.java:790)
oracle.workspaces.install.CwCAException: Error while executing action: "setup_backend"
Caused by: javax.naming.directory.NoSuchAttributeException: [LDAP: error code 16 - One or more values for attribute uniquemember does not exist]
at oracle.workspaces.install.CwConfig.run(CwConfig.java:639)
at oracle.workspaces.install.CwConfig.main(CwConfig.java:790)
Caused by: javax.naming.directory.NoSuchAttributeException: [LDAP: error code 16 - One or more values for attribute uniquemember does not exist]; remaining name 'cn=Service Registry Admins,cn=Groups,cn=OracleContext'
at com.sun.jndi.ldap.LdapCtx.mapErrorCode(LdapCtx.java:3009)
at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2934)
at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2740)
at com.sun.jndi.ldap.LdapCtx.c_modifyAttributes(LdapCtx.java:1373)
at com.sun.jndi.toolkit.ctx.ComponentDirContext.p_modifyAttributes(ComponentDirContext.java:235)
at com.sun.jndi.toolkit.ctx.PartialCompositeDirContext.modifyAttributes(PartialCompositeDirContext.java:147)
at com.sun.jndi.toolkit.ctx.PartialCompositeDirContext.modifyAttributes(PartialCompositeDirContext.java:136)
at javax.naming.directory.InitialDirContext.modifyAttributes(InitialDirContext.java:136)
at oracle.workspaces.share.util.oid.OIDShareUtil.setEntryAttribute(OIDShareUtil.java:471)
at oracle.workspaces.share.util.oid.OIDShareUtil.addMemberToGroup(OIDShareUtil.java:420)
at oracle.workspaces.share.util.oid.OIDShareUtil.addMemberToGroupIgnoreDuplicateMember(OIDShareUtil.java:435)
at oracle.workspaces.install.CwConfigOID.createBackendEntity(CwConfigOID.java:1205)
at oracle.workspaces.install.CwConfigOID.registerBackend(CwConfigOID.java:449)
at oracle.workspaces.install.CwConfig.regBackend(CwConfig.java:320)
at oracle.workspaces.install.CwConfig.run(CwConfig.java:609)
... 1 more
javax.naming.directory.NoSuchAttributeException: [LDAP: error code 16 - One or more values for attribute uniquemember does not exist]; remaining name 'cn=Service Registry Admins,cn=Groups,cn=OracleContext'
at com.sun.jndi.ldap.LdapCtx.mapErrorCode(LdapCtx.java:3009)
at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2934)
at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2740)
at com.sun.jndi.ldap.LdapCtx.c_modifyAttributes(LdapCtx.java:1373)
at com.sun.jndi.toolkit.ctx.ComponentDirContext.p_modifyAttributes(ComponentDirContext.java:235)
at com.sun.jndi.toolkit.ctx.PartialCompositeDirContext.modifyAttributes(PartialCompositeDirContext.java:147)
at com.sun.jndi.toolkit.ctx.PartialCompositeDirContext.modifyAttributes(PartialCompositeDirContext.java:136)
at javax.naming.directory.InitialDirContext.modifyAttributes(InitialDirContext.java:136)
at oracle.workspaces.share.util.oid.OIDShareUtil.setEntryAttribute(OIDShareUtil.java:471)
at oracle.workspaces.share.util.oid.OIDShareUtil.addMemberToGroup(OIDShareUtil.java:420)
at oracle.workspaces.share.util.oid.OIDShareUtil.addMemberToGroupIgnoreDuplicateMember(OIDShareUtil.java:435)
at oracle.workspaces.install.CwConfigOID.createBackendEntity(CwConfigOID.java:1205)
at oracle.workspaces.install.CwConfigOID.registerBackend(CwConfigOID.java:449)
at oracle.workspaces.install.CwConfig.regBackend(CwConfig.java:320)
at oracle.workspaces.install.CwConfig.run(CwConfig.java:609)
at oracle.workspaces.install.CwConfig.main(CwConfig.java:790)
What should i do?
help.
Thanksclosed
Re: Install OCS 10.1.2 Infra DB failed with LDAP: error code 16 on Workspac -
Hi I have just reinstalled Win 7 Ultimate and the validation has failed due to error code 0xC004E003. all of the windows updates have been complete.
when I run slui 4 and I do not get an option to activate by phone and I have tried running the Command prompt "cscript %windir%\System32\slmgr.vbs /ilc %windir%\System32\licensing\ppdlic\Security-Licensing-SLC-ppdlic.xrm-ms" which errored
out
Bellow is the MGADiag tool output
Diagnostic Report (1.9.0027.0):
Windows Validation Data-->
Validation Code: 0
Cached Online Validation Code: 0x0
Windows Product Key: *****-*****-X92GV-V7DCV-P4K27
Windows Product Key Hash: aU2z1/fnhnLHmhBm699qYZT2E6s=
Windows Product ID: 00426-OEM-8992662-00400
Windows Product ID Type: 2
Windows License Type: OEM SLP
Windows OS version: 6.1.7601.2.00010100.1.0.001
ID: {58492533-DAC0-4F4B-8CB4-7C2572CD6AD2}(3)
Is Admin: Yes
TestCab: 0x0
LegitcheckControl ActiveX: N/A, hr = 0x80070002
Signed By: N/A, hr = 0x80070002
Product Name: Windows 7 Ultimate
Architecture: 0x00000009
Build lab: 7601.win7sp1_gdr.130828-1532
TTS Error:
Validation Diagnostic:
Resolution Status: N/A
Vista WgaER Data-->
ThreatID(s): N/A, hr = 0x80070002
Version: N/A, hr = 0x80070002
Windows XP Notifications Data-->
Cached Result: N/A, hr = 0x80070002
File Exists: No
Version: N/A, hr = 0x80070002
WgaTray.exe Signed By: N/A, hr = 0x80070002
WgaLogon.dll Signed By: N/A, hr = 0x80070002
OGA Notifications Data-->
Cached Result: N/A, hr = 0x80070002
Version: N/A, hr = 0x80070002
OGAExec.exe Signed By: N/A, hr = 0x80070002
OGAAddin.dll Signed By: N/A, hr = 0x80070002
OGA Data-->
Office Status: 109 N/A
OGA Version: N/A, 0x80070002
Signed By: N/A, hr = 0x80070002
Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3
Browser Data-->
Proxy settings: N/A
User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
Default Browser: C:\Program Files (x86)\Mozilla Firefox\firefox.exe
Download signed ActiveX controls: Prompt
Download unsigned ActiveX controls: Disabled
Run ActiveX controls and plug-ins: Allowed
Initialize and script ActiveX controls not marked as safe: Disabled
Allow scripting of Internet Explorer Webbrowser control: Disabled
Active scripting: Allowed
Script ActiveX controls marked as safe for scripting: Allowed
File Scan Data-->
Other data-->
Office Details: <GenuineResults><MachineData><UGUID>{58492533-DAC0-4F4B-8CB4-7C2572CD6AD2}</UGUID><Version>1.9.0027.0</Version><OS>6.1.7601.2.00010100.1.0.001</OS><Architecture>x64</Architecture><PKey>*****-*****-*****-*****-P4K27</PKey><PID>00426-OEM-8992662-00400</PID><PIDType>2</PIDType><SID>S-1-5-21-3905371182-2698555194-554347162</SID><SYSTEM><Manufacturer>Dell
Inc.</Manufacturer><Model>Latitude E6520</Model></SYSTEM><BIOS><Manufacturer>Dell Inc.</Manufacturer><Version>A18</Version><SMBIOSVersion major="2" minor="6"/><Date>20130628000000.000000+000</Date></BIOS><HWID>A05B3107018400FE</HWID><UserLCID>0809</UserLCID><SystemLCID>0409</SystemLCID><TimeZone>GMT
Standard Time(GMT+00:00)</TimeZone><iJoin>0</iJoin><SBID><stat>3</stat><msppid></msppid><name></name><model></model></SBID><OEM><OEMID>DELL </OEMID><OEMTableID>CBX3
</OEMTableID></OEM><GANotification/></MachineData><Software><Office><Result>109</Result><Products/><Applications/></Office></Software></GenuineResults>
Spsys.log Content: 0x80070002
Licensing Data-->
Software licensing service version: 6.1.7601.17514
Name: Windows(R) 7, Ultimate edition
Description: Windows Operating System - Windows(R) 7, OEM_SLP channel
Activation ID: 7cfd4696-69a9-4af7-af36-ff3d12b6b6c8
Application ID: 55c92734-d682-4d71-983e-d6ec3f16059f
Extended PID: 00426-00178-926-600400-02-2057-7601.0000-0452014
Installation ID: 015022194896715926564380852615762536846771772141316646
Processor Certificate URL: http://go.microsoft.com/fwlink/?LinkID=88338
Machine Certificate URL: http://go.microsoft.com/fwlink/?LinkID=88339
Use License URL: http://go.microsoft.com/fwlink/?LinkID=88341
Product Key Certificate URL: http://go.microsoft.com/fwlink/?LinkID=88340
Partial Product Key: P4K27
License Status: Initial grace period
Time remaining: 37860 minute(s) (26 day(s))
Remaining Windows rearm count: 3
Trusted time: 14/02/2014 09:02:26
Windows Activation Technologies-->
HrOffline: 0x00000000
HrOnline: 0x00000000
HealthStatus: 0x0000000000000000
Event Time Stamp: 2:14:2014 09:00
ActiveX: Registered, Version: 7.1.7600.16395
Admin Service: Registered, Version: 7.1.7600.16395
HealthStatus Bitmask Output:
HWID Data-->
HWID Hash Current: NAAAAAEAAQABAAIAAAACAAAABAABAAEAHKLYsxuJLAK4jqbIhjvuI1YXxgem9B73it4ucw==
OEM Activation 1.0 Data-->
N/A
OEM Activation 2.0 Data-->
BIOS valid for OA 2.0: yes
Windows marker version: 0x20001
OEMID and OEMTableID Consistent: yes
BIOS Information:
ACPI Table Name OEMID Value OEMTableID Value
APIC DELL CBX3
FACP DELL CBX3
HPET A M I PCHHPET
BOOT DELL CBX3
MCFG DELL SNDYBRDG
TCPA
SSDT DELLTP TPM
SSDT DELLTP TPM
SSDT DELLTP TPM
DMAR INTEL SNB
SLIC DELL CBX3
SSDT DELLTP TPMHi,
The error code 0xC004E003 means that the Software Licensing Service reported that license evaluation failed.
We may need to involve the phone activation center and check if they can resolve the issue:
How to contact a Microsoft Product Activation Center by telephone
http://support.microsoft.com/kb/950929/
Meanwhile, you should post your question in the forum mentioned by Kamin of Ressik. They are the most knowledgeable about the topic.
Hope it helps.
Regards,
Blair Deng
Blair Deng
TechNet Community Support -
Hi,<BR>While adding/Changing member in planning it gives the error "The SQL operation failed with an error code: 0" and not allowing any of the changes. I am not able to open the forms giving the error as "Fiscal Days Input - is invalid". Interestingly one form was opening, when the Page selection is changed it also started giving error as like "Fisacal Days Input(form name) - is invalid check log for details". <BR>Pls advice us that what is this error and how to resolve this.<BR><BR>And Which log is to be referred for the details.<BR><BR>Thanks<BR>Ravi
If a form is invalid it generally means that one of the dimension references is missing.<BR><BR>Can you get in to edit the form?<BR>If you can, see if you can preview it. I suspect you will not be able to.<BR><BR>If not, check all dimension boxes have at least one member against them.<BR>If you have multiple rows and/or columns check all of them too.<BR><BR>I've had a couple of forms in dev "drop" a dimension reference but only once or twice so not enough to reproduce or find out what is causing it. Each time I got the "form invalid" error message and managed to fix it.<BR><BR>Hope this helps.<BR>
-
Creative cloud failed to update error code: 1
free trial of creative cloud failed to update error code: 1 so I couldn't use the creative cloud. Please help, thanks a lot!!
Hi jadyyuk,
Please try the solution mentioned in the KB : http://helpx.adobe.com/creative-cloud/kb/a12e1-error-downloading-creative-cloud.html -
Hello,
i am trying to connect to my corporation VPN Server " ISA 2006" using windows 8.1 client built in VPN, but its returned the following error:
Event ID 20227: dialed a connection named "VPN connection Name" which has failed. The error code returned on failure is 789.
VPN connection is working fine with windows XP and windows 7 with no issue , this error is only appear when try to connect to using windows 8 client machine.
this error is shows only on windows 8.1 client , same procedures used to enroll the certificate from internal CA " IPsec Type" is followed .
below are the ISA server specifications:
VPN Server : ISA 2006.
windows Server version 2003.
appreciate your quick help and reply .
ThanksThanks for your reply.
i would like to add another point for this case, that when we are trying to enroll a certificate from internal CA web enrollment directly using windows 8 " internet explorer 11" , its install a certificate without Digital
Signature and non-repudiation in key usage property, then when try to connect , its will give the above error 789 ..
when try to enroll a certificate into windows 7 " internet explorer 10" and then export and import this certificate into windows 8.1 machine "with the name of
windows 8.1 machine" into windows 8.1 machine, the VPN is working normally and without issue.
The properties of the Certificate are difference between windows 7 machine and windows 8 machine is key usage missing the Digital Signature and non-repudiation properties when enroll
from windows 8.1 " internet explorer 11", this is in fact because of
we don't have an option for key usage " both" when subment a certificate on web enrollment page from windows 8 machine ,, the only option available is exchange "
no signature and both option available "
i believe that there is something wrong when using windows 8.1 internet explorer 11 so its gave a certificate with wrong key usage property .
appreciate your quick help in this .
thanks -
VPN error - Function CreateFile failed with an error code of 0x00000002
I got an error when connecting VPN, detailed messages are attached. I am using administrator to log on. The issue is there after I run a virus clean activity. Any help is appreciated.
Cisco Systems VPN Client Version 4.6.04.0043
Copyright (C) 1998-2005 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 5.1.2600 Service Pack 2
1 15:16:21.625 10/10/09 Sev=Warning/2 CVPND/0xE3400003
Function CreateFile failed with an error code of 0x00000002(DRVIFACE:718)
2 15:16:22.546 10/10/09 Sev=Warning/2 CVPND/0xE3400003
Function CreateFile failed with an error code of 0x00000002(DRVIFACE:718)
3 15:16:23.046 10/10/09 Sev=Warning/2 CVPND/0xE3400003
Function CreateFile failed with an error code of 0x00000002(DRVIFACE:718)
4 15:16:23.546 10/10/09 Sev=Warning/2 CVPND/0xE3400003
Function CreateFile failed with an error code of 0x00000002(DRVIFACE:718)
5 15:16:24.046 10/10/09 Sev=Warning/2 CVPND/0xE3400003
Function CreateFile failed with an error code of 0x00000002(DRVIFACE:718)
6 15:16:24.546 10/10/09 Sev=Warning/2 CVPND/0xE3400003
Function CreateFile failed with an error code of 0x00000002(DRVIFACE:718)
7 15:16:25.046 10/10/09 Sev=Warning/2 CVPND/0xE3400003
Function CreateFile failed with an error code of 0x00000002(DRVIFACE:718)
8 15:16:25.546 10/10/09 Sev=Warning/2 CVPND/0xE3400003
Function CreateFile failed with an error code of 0x00000002(DRVIFACE:718)
9 15:16:26.046 10/10/09 Sev=Warning/2 CVPND/0xE3400003
Function CreateFile failed with an error code of 0x00000002(DRVIFACE:718)
10 15:16:26.546 10/10/09 Sev=Warning/2 CVPND/0xE3400003
Function CreateFile failed with an error code of 0x00000002(DRVIFACE:718)Please see my post in the IPsec and Firewall forum.
-
The Volume Shadow Copy service initially was running under the context of System, so we thought that ‘System’ doesn’t have permissions to access network shares.
When the Volume Shadow Copy service was running under the context of System, this was the error logged:
“failed with following error code '0x8078014B' (There was a failure in creating a directory on the backup storage location.).”
Which is likely due to not having permissions to write to the network location.
This is a scheduled backup trying to write to a network location, so we changes the service to run under the context of an account that does have permissions to write to the network share.
Then the error changed to this:
“failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).”
HRESULT 0x8078006b
DetailedHRESULT 0x8004230f
ErrorMessage %%2155348075
BackupState 12
VolumesInfo <VolumeInfo><VolumeInfoItem Name="C:" OriginalAccessPath="C:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="1" IsIncremental="0"
BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0"
TotalNoOfFiles="0" Flags="1604" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /><VolumeInfoItem Name="D:" OriginalAccessPath="D:" State="15" HResult="-2139619228"
DetailedHResult="0" PreviousState="0" IsCritical="0" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0"
FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="68" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0"
/></VolumeInfo>
We aren’t really seeing anything that gives any hint on what the issue is.
Any ideas? Thanks in advance!We are trying to back up folders/files from 2 local drives (C: & D:), both of which have only 10% space used, and 100 GB free.
We are attempting to back the files up to a Remote Shared File (and there is 100+ GB free space out there).
If we try another network location, we receive the exact same error.
This is Windows Server 2012, not running Hyper-V and is a physical server not a VM.
Thank you for the link.
Looking in:
Event Viewer / Application and Service Logs / Microsoft / Windows / Backup / Operational
But it doesn’t seem to give any more details:
Log Name:
Microsoft-Windows-Backup
Source:
Microsoft-Windows-Backup
Date:
7/8/2013 8:00:12 PM
Event ID:
5
Task Category: None
Level:
Error
Keywords:
User:
SYSTEM
Computer:
servername.edu
Description:
The backup operation that started at '2013-07-09T02:00:06.273000000Z' has failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).
Please review the event details for a solution, and then rerun the backup operation once the issue is resolved.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-Backup" Guid="{1DB28F2E-8F80-4027-8C5A-A11F7F10F62D}" />
<EventID>5</EventID>
<Version>3</Version>
<Level>2</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x4000000000000000</Keywords>
<TimeCreated SystemTime="2013-07-09T02:00:12.872602100Z" />
<EventRecordID>30</EventRecordID>
<Correlation />
<Execution ProcessID="3028" ThreadID="3996" />
<Channel>Microsoft-Windows-Backup</Channel>
<Computer>servername.edu</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data Name="BackupTemplateID">{A421E864-A115-4288-8D12-F4878CF8A248}</Data>
<Data Name="HRESULT">0x8078006b</Data>
<Data Name="DetailedHRESULT">0x8004230f</Data>
<Data Name="ErrorMessage">%%2155348075</Data>
<Data Name="BackupState">12</Data>
<Data Name="BackupTime">2013-07-09T02:00:06.273000000Z</Data>
<Data Name="BackupTarget">\\servername\BACKUP</Data>
<Data Name="NumOfVolumes">2</Data>
<Data Name="VolumesInfo"><VolumeInfo><VolumeInfoItem Name="C:" OriginalAccessPath="C:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="1" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0"
IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="1604" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /><VolumeInfoItem
Name="D:" OriginalAccessPath="D:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="0" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0"
NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="68" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /></VolumeInfo></Data>
<Data Name="SourceSnapStartTime">2013-07-09T02:00:06.289250300Z</Data>
<Data Name="SourceSnapEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="PrepareBackupStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="PrepareBackupEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="BackupWriteStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="BackupWriteEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="TargetSnapStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="TargetSnapEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="DVDFormatStartTime"><TimesList></TimesList></Data>
<Data Name="DVDFormatEndTime"><TimesList></TimesList></Data>
<Data Name="MediaVerifyStartTime"><TimesList></TimesList></Data>
<Data Name="MediaVerifyEndTime"><TimesList></TimesList></Data>
<Data Name="BackupPreviousState">2</Data>
<Data Name="ComponentStatus"><ComponentStatus></ComponentStatus></Data>
<Data Name="ComponentInfo"><ComponentInfo></ComponentInfo></Data>
<Data Name="SSBEnumerateStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBEnumerateEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBVhdCreationStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBVhdCreationEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBBackupStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBBackupEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SystemStateBackup"><SystemState IsPresent="0" HResult="0" DetailedHResult="0" /></Data>
<Data Name="BMR"><BMR IsPresent="0" HResult="0" DetailedHResult="0" /></Data>
<Data Name="VssFullBackup">false</Data>
<Data Name="UserInputBMR">false</Data>
<Data Name="UserInputSSB">false</Data>
<Data Name="BackupSuccessLogPath">
</Data>
<Data Name="BackupFailureLogPath">
</Data>
<Data Name="EnumerateBackupStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="EnumerateBackupEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="PruneBackupStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="PruneBackupEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="BackupFlags">0x9</Data>
<Data Name="ComponentInfoSummary"><ComponentInfoSummary ComponentInfoArrayPresent="1" TotalComponents="0" SucceededComponents="0" /></Data>
</EventData>
</Event> -
My macbook pro intel core duo 2 keeps restarting intermittenly. Help with error code.
I have run a Hardware Test, and it gives the follwing error code. Can anyone tell me what this is? I recently had my logic board replaced within the last 3 months, so it shouldn't be a problem there.
Thank you very much for any and all help.
Error code:
4SNS/I/40000000:TGOH-128.00Online references possible memory issue? Sensors?
https://discussions.apple.com/thread/3140607?start=0&tstart=0
Keep taking it back and they keep switching parts until the problem is gone. -
Downloading the new IPhone software update keeps failing ,I get error code -3259 is there a fix for this
Disable the security software and try again, Kaspersky's has been really annoying with this along with a couple others.
-
I tried to update Photoshop CC 2014, but it failed at 75%, with error code U44M1I210. After restarting my system, it still failed so I uninstalled the app, per this article: https://helpx.adobe.com/creative-suite/kb/error-u44m1i210-installing-updates-ccm.html
Now the reinstall won't complete, and I'm getting error -55. The one other article that seemed relevant looks like the person had to uninstall and reinstall all his Adobe software after creating a new admin account on his computer (When I try to update I get an U44M1I210 error message, "Unable to extract the downloaded files" - help please, applies to latest Indesign, Illustrator and Photoshop CC), and I'm hoping there is a better solution than the hours that will involve.
Running on OSX 10.7.5.
Any help greatly appreciated.
Thanks!GundamCat what specific errors were you able to discover in the installation log for the update?
Maybe you are looking for
-
How do i transfer all data from one mac to another?
When I started up my new iMac, there was an option to transfer all my data from my older mac (macbook air) to the new iMac. I skipped this step at first, how can I get back to this step and utilize this feature?
-
I have tryed to restore my i phone and it wont let me what do i do?
I plugged my i phone 3gs into i tunes to restore it an it only got 3 quraters the way done an it stopped and now everytime you turn it on it comes up contect to i tunes, i done this again tonight and it has froze on a black screen with the apple sign
-
Hundreds of ERROR = KEY_MISMATCH in emoms.trc
I am pretty sure this is because the agent was not secured. I have 1000s of these errors in my log file and its cluttering my grid control logs. I can't find legitimate issues. Its another group, so I can't get on their server to shut down the agent.
-
I am trying to print in black and white using black ink only. Supposedly I am to go to Software Program then go to Print and then the Paper Quality tab and then click print black, but I can not figure out how to find the Software Program drop down t
-
Showing iViews with Web Page Composer
Hi guys, I have to use iViews in a Web Page in Web Page Composer. I was searching some info in snd but i couldn't find anything about it. Can somebody help me? Best regards.