RAIDXpert reporting errors on nonRAID device

My machine is a HP Pavilion Elite HPE-110f, and the hard drive is WD10EADS-65M2B1 SCSI Device. When my machine arrived, it had RAIDXpert running on it, and about 3 months after I bought it, it started reporting bad sectors (I think). As it was under warranty, I shipped it to HP, who cleaned off the disk and shipped it back. On the second day after getting it back, RAIDXpert started reporting errors (same sectors as before). Now WD tells me the drive is not a RAID device! Could someone tell me what is going on, and what I should do about it (apart from stopping RAIDXpert!)? BTW When I started getting Bad Sector errors, I ran the WD DataLifeguard program, and it also reported errors - and said it couldn't fix them. I am going to run it again (but it takes hours!).
Thanks.

After getting the computer back, I ran WD DataLifeguard program (twice), and each time it came up with a message to the effect that it was bringing down the computer "to prevent damage to the computer"... and brought the computer down! It didn't do that before I sent it off! So it came back in worse shape than when it left...?!
Does anyone know whether the WD 1T SCSI disk is reliable? Are there better drives out there? TIA

Similar Messages

DVD Burn problem. "Device error - the target device isn't suitable for use"

Hello everyone,
I initially had a lot of problems with PE8. However the nVidia driver update solved most of them.
Just thought it was important to report success as well as failure!
However one problem remains. I get the following error at the 96% mark while burning. "Device error - the target device isn't suitable for use". It is always at the 96% mark and the program is "compiling [something]" when this happens.
Having searched this site I notice that user rgferg posted a similar problem 13 days ago but was redirected to repost in a different place, but never did.
I have tried to burn a 1hr clip 4 times and every time I have selected the slower burn speed (8MB/s) as has been suggested. It seems that inferior media is a culprit, so I have bought some [quality] Verbatim DVD-R media to try in my Phillips SATA optical drive. I am sceptical this will work, but open minded nonetheless. I will give it a whirl when my computer has stopped capturing the VHS I am working on.
Each time the burn failed the disk was automatically ejected and the burn process had actually started and progressed perhaps ~40% or so.
This indicates to me that it is a drive sharing issue, rather than a media issue. Somewhere on this forum it suggests that I go through a 20+ step process and delete/disable every piece of software that can compete with Premiere among other things. IF I do this what do I burn with outside of Adobe? Do I have to get imgburn or whatever it was called? What if I like Nero? Nero 6 has worked great for me for 3 years.
So given I am willing to uninstall my old optical drive burning software, who out there can recommened commercial software that for them creates a painless Adobe burning experience with no errors or conflicts? Perhaps there is another solution that I did not see on this forum?
I am running Windows XP SP3. I have the latest nVidia drivers for my SLI GeForce 7600 GS cards. I have 3 monitors. RAID 0 SATA, 2GB RAM, Athlon X2 5400.
Justin.

OK been working through the list of 20 things Adobe recommends to fix DVD burn error. No luck yet:
system meets minimum requirements
Project size does not exceed disk capacity
successfully burned project to DVD folder -thus skip to step 8.
8. Using new blank media for burning
9. Try different media and DVD burners. Bought Verbatim DVD-R. Don't have another DVD burner. Adobe's supported burner list is VERY short, so of course mine is not on it.
10. Uninstalled Nero 6. Did NOT uninstall Acronis True Image workstation or Lightscribe. These do not access the drive unless I say so!
11. Have not yet disabled startup items and services. This will take a lot of work and will leave to last. Deactivated Spybot thus far.....
12. Disabled IMAPI CD burning COM
13. DMA if available already set. Haven't set this in BIOS yet. I already think it is, but will check next boot.
14. Updated DVD firmware
15. Already updated nVidia drivers
16. Don't have any other DVD drives to disconnect.
17. MPEG workaround. Will resort to if required.
18. Disable Autoplay? XP only has "prompt me each time to choose an action". I have set this for ALL file types.
19. Have NOT refreshed the DVD drivers in the registry. This step involves uninstalling PE8. Will leave this as last resort.
20. Visit forums to see if other have the same problem. Hi guys
So still working through some of the items above.
Can anyone direct me to advice on how to write the encoded files sent to the hard drive, or the VOB files that PE8 failed to burn to a disk? Will the former work with DVD menus?
What a process.
Stay tuned.
Justin.

Device error -the target device isn't suitable for use. Solution found!?

Hello everyone,
I have received the following error many times on my machine for different projects when trying to burn to disk and folders:
Device error -the target device isn't suitable for use.
I have multiple hard drives with ~60GB, 40GB and 12GB. I have tried to burn 4.7GB discs and folders and 8.5GB folders.
I have previously tried nearly ALL 20 troubleshooting items recommended by Adobe and have even changed to Verbatim media. None of these solved the problem.
What did solve the problem, EVERY SINGLE TIME, was freeing up hard drive space or reducing the length of the project.
You may look at the available hard drive space and THINK that you have enough. But you don't.
Perhaps the remainder of this thread could be used to discuss the disk space requirements for projects. I can't seem to crack the formula. I just keep deleting/archiving files until the project works. I have ordered some new big HDD's to be rid of this error forever.
Justin.

While it is certainly possible that diskspace is one factor in getting the dreaded "target device isn't suitable message" (usually after lenghthy processing), it does not appear to be the only one.
I got the message trying to burn a 3 minute video to a dvd on two seperate computers one running xp pro with 150Gb of spare disk space and one running W7 HP with 50Gb of spare space. Tryng to burn to a folder gave the same error.
To me, this pointed to something in the app, or the project, so firstly I deleted the disk menu...burn completed ok. Re-instated a menu (different one)....burn failed. Removed one scene marker and the stop marker......burn completed ok. Re-instated stop marker......burn failed
Am I missing something on the purpose of the stop marker?
There was nothing obviously wrong with the project, although I will admit that I am new to PRE but am not a complete novice to video editing.
The encoding process of the menu's (both passes) went ok, and it wasn't until it got to the "encoding media" phase that the error message appeared.
It would certainly seem that more illuminating error reporting would be beneficial in this case, but it would also seem to be worth trying changes to the menus or markers to see if that fixes the error message.

Bumblebee daemon reported: error - ASUS UX303LN,bumblebee,geforce 840m

Hello. I am trying to get bumblebee up and running but there seems to be an issue. This is what i've done:
sudo pacman -S bumblebee mesa xf86-video-intel nvidia lib32-nvidia-utils lib32-mesa-libgl
gpasswd -a $USER bumblebee
sudo systemctl enable bumblebeed
reboot
But when i try to test it out i get the output:
primusrun glxspheres64
primus: fatal: Bumblebee daemon reported: error: [XORG] (EE) systemd-logind: failed to get session: PID 635 does not belong to any known session
So i whent onto the wiki and found this: (and also installed bbswitch)
systemd-logind: failed to get session: PID XXX does not belong to any known session
If the console output is (PID varies):
[ERROR]Cannot access secondary GPU - error: [XORG] (EE) systemd-logind: failed to get session: PID 753 does not belong to any known session
[ERROR]Aborting because fallback start is disabled.
In /etc/mkinitcpio.conf change the MODULES var to:
MODULES="i915 bbswitch"
Or:
MODULES="i915 nouveau bbswitch"
And run:
# mkinitcpio -p linux
mkinitcpio ran fine with no errors. After i rebooted i got promoted with the same error. Can anyone give me a hint on if im missing someting?
lspci
00:00.0 Host bridge: Intel Corporation Haswell-ULT DRAM Controller (rev 0b)
00:02.0 VGA compatible controller: Intel Corporation Haswell-ULT Integrated Graphics Controller (rev 0b)
00:03.0 Audio device: Intel Corporation Haswell-ULT HD Audio Controller (rev 0b)
00:04.0 Signal processing controller: Intel Corporation Device 0a03 (rev 0b)
00:14.0 USB controller: Intel Corporation 8 Series USB xHCI HC (rev 04)
00:16.0 Communication controller: Intel Corporation 8 Series HECI #0 (rev 04)
00:1b.0 Audio device: Intel Corporation 8 Series HD Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 8 Series PCI Express Root Port 1 (rev e4)
00:1c.3 PCI bridge: Intel Corporation 8 Series PCI Express Root Port 4 (rev e4)
00:1c.4 PCI bridge: Intel Corporation 8 Series PCI Express Root Port 5 (rev e4)
00:1f.0 ISA bridge: Intel Corporation 8 Series LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation 8 Series SATA Controller 1 [AHCI mode] (rev 04)
00:1f.3 SMBus: Intel Corporation 8 Series SMBus Controller (rev 04)
00:1f.6 Signal processing controller: Intel Corporation 8 Series Thermal (rev 04)
02:00.0 Network controller: Intel Corporation Wireless 7260 (rev bb)
03:00.0 3D controller: NVIDIA Corporation GM108M [GeForce 840M] (rev a2)
pacman -Q | grep linux
archlinux-keyring 20150212-1
lib32-util-linux 2.26-1
libutil-linux 2.26.1-3
linux 3.19.2-1
linux-api-headers 3.18.5-1
linux-firmware 20150206.17657c3-1
linux-git 4.0rc4.r199.gb314aca-1
linux-git-docs 4.0rc4.r199.gb314aca-1
linux-git-headers 4.0rc4.r199.gb314aca-1
linux-headers 3.19.2-1
util-linux 2.26.1-3

dice wrote:
So which kernel are you trying to run bumblebee on?
If you try to run it on v4 you probably need to compile the nvidia modules against this version.
What does
systemctl status bumblebeed
give you right after reboot?
I always use v4 and have been used when i installed the drivers. Anything i need to do?
systemctl status bumblebeed
● bumblebeed.service - Bumblebee C Daemon
Loaded: loaded (/usr/lib/systemd/system/bumblebeed.service; enabled; vendor preset: disabled)
Active: active (running) since fre 2015-03-27 14:14:07 CET; 11min ago
Main PID: 449 (bumblebeed)
CGroup: /system.slice/bumblebeed.service
└─449 /usr/bin/bumblebeed
mar 27 14:14:42 laptop bumblebeed[449]: [ 64.920660] [WARN][XORG] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
mar 27 14:14:42 laptop bumblebeed[449]: [ 64.920669] [ERROR][XORG] (EE) [drm] KMS not enabled
mar 27 14:14:42 laptop bumblebeed[449]: [ 64.920673] [ERROR][XORG] (EE) No devices detected.
mar 27 14:14:42 laptop bumblebeed[449]: [ 64.920676] [ERROR][XORG] (EE)
mar 27 14:14:42 laptop bumblebeed[449]: [ 64.920679] [ERROR][XORG] (EE) no screens found(EE)
mar 27 14:14:42 laptop bumblebeed[449]: [ 64.920682] [ERROR][XORG] (EE)
mar 27 14:14:42 laptop bumblebeed[449]: [ 64.920686] [ERROR][XORG] (EE) Please also check the log file at "/var/log/Xorg.8.log" for additional information.
mar 27 14:14:42 laptop bumblebeed[449]: [ 64.920690] [ERROR][XORG] (EE)
mar 27 14:14:42 laptop bumblebeed[449]: [ 64.920693] [ERROR][XORG] (EE) Server terminated with error (1). Closing log file.
mar 27 14:14:42 laptop bumblebeed[449]: [ 64.920696] [ERROR]X did not start properly
Sorry, that one was not right after reboot. This one is tho (inside i3wm):
systemctl status bumblebeed
● bumblebeed.service - Bumblebee C Daemon
Loaded: loaded (/usr/lib/systemd/system/bumblebeed.service; enabled; vendor preset: disabled)
Active: active (running) since fre 2015-03-27 15:57:08 CET; 1min 15s ago
Main PID: 453 (bumblebeed)
CGroup: /system.slice/bumblebeed.service
└─453 /usr/bin/bumblebeed
mar 27 15:57:08 laptop systemd[1]: Started Bumblebee C Daemon.
mar 27 15:57:08 laptop systemd[1]: Starting Bumblebee C Daemon...
mar 27 15:57:08 laptop bumblebeed[453]: modprobe: FATAL: Module bbswitch not found.
mar 27 15:57:08 laptop bumblebeed[453]: [ 33.470972] [ERROR]Module bbswitch could not be loaded (timeout?)
mar 27 15:57:08 laptop bumblebeed[453]: [ 33.470986] [WARN]No switching method available. The dedicated card will always be on.
mar 27 15:57:08 laptop bumblebeed[453]: [ 33.471866] [INFO]/usr/bin/bumblebeed 3.2.1 started
I ran
sudo modprobe bbswitch
And the bbswitch error disapeard but now im back on the first log with xorg errors.
/var/log/Xorg.8.log
[ 78.331]
X.Org X Server 1.17.1
Release Date: 2015-02-10
[ 78.331] X Protocol Version 11, Revision 0
[ 78.331] Build Operating System: Linux 3.18.6-1-ARCH x86_64
[ 78.331] Current Operating System: Linux laptop 4.0.0-rc4-gb314aca #1 SMP PREEMPT Fri Mar 20 13:23:44 CET 2015 x86_64
[ 78.331] Kernel command line: BOOT_IMAGE=/vmlinuz-linux-git root=/dev/mapper/store-root rw cryptdevice=/dev/sda:enc:header rcutree.rcu_idle_gp_delay=1
[ 78.331] Build Date: 14 March 2015 06:45:50PM
[ 78.331]
[ 78.331] Current version of pixman: 0.32.6
[ 78.331] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 78.331] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 78.331] (==) Log file: "/var/log/Xorg.8.log", Time: Fri Mar 27 16:11:13 2015
[ 78.332] (++) Using config file: "/etc/bumblebee/xorg.conf.nouveau"
[ 78.332] (++) Using config directory: "/etc/bumblebee/xorg.conf.d"
[ 78.332] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 78.334] (==) ServerLayout "Layout0"
[ 78.334] (==) No screen section available. Using defaults.
[ 78.334] (**) |-->Screen "Default Screen Section" (0)
[ 78.334] (**) | |-->Monitor "<default monitor>"
[ 78.334] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 78.334] (**) | |-->Device "DiscreteNvidia"
[ 78.334] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 78.334] (**) Option "AutoAddDevices" "false"
[ 78.334] (**) Option "AutoAddGPU" "false"1
[ 78.334] (**) Not automatically adding devices
[ 78.334] (==) Automatically enabling devices
[ 78.334] (**) Not automatically adding GPU devices
[ 78.334] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/OTF/".
[ 78.334] Entry deleted from font path.
[ 78.334] (Run 'mkfontdir' on "/usr/share/fonts/OTF/").
[ 78.334] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/
[ 78.334] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 78.334] (==) |-->Input Device "<default pointer>"
[ 78.334] (==) |-->Input Device "<default keyboard>"
[ 78.334] (==) The core pointer device wasn't specified explicitly in the layout.
Using the default mouse configuration.
[ 78.334] (==) The core keyboard device wasn't specified explicitly in the layout.
Using the default keyboard configuration.
[ 78.334] (II) Loader magic: 0x815d80
[ 78.334] (II) Module ABI versions:
[ 78.334] X.Org ANSI C Emulation: 0.4
[ 78.334] X.Org Video Driver: 19.0
[ 78.334] X.Org XInput driver : 21.0
[ 78.334] X.Org Server Extension : 9.0
[ 78.335] (EE) systemd-logind: failed to get session: PID 927 does not belong to any known session
[ 78.335] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 78.335] (EE) /dev/dri/card0: failed to set DRM interface version 1.4: Permission denied
[ 78.336] (--) PCI:*(0:3:0:0) 10de:1341:1043:167d rev 162, Mem @ 0xf6000000/16777216, 0xe0000000/268435456, 0xf0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288
[ 78.336] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 78.336] (II) LoadModule: "glx"
[ 78.336] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 78.337] (II) Module glx: vendor="X.Org Foundation"
[ 78.337] compiled for 1.17.1, module version = 1.0.0
[ 78.337] ABI class: X.Org Server Extension, version 9.0
[ 78.337] (==) AIGLX enabled
[ 78.337] (II) LoadModule: "nouveau"
[ 78.337] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
[ 78.340] (II) Module nouveau: vendor="X.Org Foundation"
[ 78.340] compiled for 1.17.0, module version = 1.0.11
[ 78.340] Module class: X.Org Video Driver
[ 78.340] ABI class: X.Org Video Driver, version 19.0
[ 78.340] (II) LoadModule: "mouse"
[ 78.341] (II) Loading /usr/lib/xorg/modules/input/mouse_drv.so
[ 78.341] (II) Module mouse: vendor="X.Org Foundation"
[ 78.341] compiled for 1.16.0, module version = 1.9.1
[ 78.341] Module class: X.Org XInput Driver
[ 78.341] ABI class: X.Org XInput driver, version 21.0
[ 78.341] (II) LoadModule: "kbd"
[ 78.341] (II) Loading /usr/lib/xorg/modules/input/kbd_drv.so
[ 78.342] (II) Module kbd: vendor="X.Org Foundation"
[ 78.342] compiled for 1.16.0, module version = 1.8.0
[ 78.342] Module class: X.Org XInput Driver
[ 78.342] ABI class: X.Org XInput driver, version 21.0
[ 78.342] (II) NOUVEAU driver
[ 78.342] (II) NOUVEAU driver for NVIDIA chipset families :
[ 78.342] RIVA TNT (NV04)
[ 78.342] RIVA TNT2 (NV05)
[ 78.342] GeForce 256 (NV10)
[ 78.342] GeForce 2 (NV11, NV15)
[ 78.342] GeForce 4MX (NV17, NV18)
[ 78.342] GeForce 3 (NV20)
[ 78.342] GeForce 4Ti (NV25, NV28)
[ 78.342] GeForce FX (NV3x)
[ 78.342] GeForce 6 (NV4x)
[ 78.342] GeForce 7 (G7x)
[ 78.342] GeForce 8 (G8x)
[ 78.342] GeForce GTX 200 (NVA0)
[ 78.342] GeForce GTX 400 (NVC0)
[ 78.342] (--) using VT number 1
[ 78.342] (EE) [drm] KMS not enabled
[ 78.342] (EE) No devices detected.
[ 78.342] (EE)
Fatal server error:
[ 78.342] (EE) no screens found(EE)
[ 78.342] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 78.342] (EE) Please also check the log file at "/var/log/Xorg.8.log" for additional information.
[ 78.342] (EE)
Last edited by AndreasEr (2015-03-27 15:15:29)

Equium A60-157: error caused by device driver

Hi all,
I'm trying to write my PhD thesis at the moment and am being hampered by my laptop! It keeps randomly bringing up the blue screen of death and then restarting; when it's all loaded up, I get a 'serious error' message that says 'error caused by device driver'. As far as I know, all the programs I have are compatible... I was advised to restore factory settings, which I did a few months ago. And I've had the BIOS update suitable for my computer. But it's still happening!!
If it helps, the programs I use daily are Microsoft Word, Access and Powerpoint, Internet Explorer and MSN Messenger. I don't run any high spec games (only Minesweeper occasionally!)
What can I do? Does anyone else have this problem? Any advice would be much appreciated, as these crashes are not helping my work!
Thanks...

Hi guys,
I seem to have a similar problem. About a month ago I reinstalled windows using the product recovery cd and three days later I started getting a blue screen. But the error occurs only when shutting down (not always, I can`t see any pattern)- right before the shut down itself, windows has already logged off and settings are saved. The error code is 0x50 and the report says it is caused by an unknown device driver.
The day that stop error started I installed an educational software (Leankey's) for which I used a virtual cd. But at the initial launch the program "freezed" and I had to close it and open it again, there wasn`t a problem. After that I tried to copy some files on a blank cd (without using any burning software) and it said that the device was not accessible.
I tried disabling DMA but that didn`t help. In the event viewer I saw error messages that say the cdrom has a bad block. I`m not sure whether this has something to do with the stop error but they started at the same time. I can still burn cds with other software (nero). I tried to update the device driver but it didn`t help.
Maybe I have to uninstall the driver first but from the device manager when I check the properties of the device (driver details) it uninstalls the device and the driver remains. Should I delete the driver files manually? I have checked all device drivers and they are all compatible. All installed software is digitally signed. (I immediately removed the Learnkey`s software but I think it has changed some dll...
I will appreciate any suggestions.
P.S. When I run the toshiba diagnostic tool it skips testing the cd/dvd but it doesn`t say why.
Details about my system:
Satellite Pro L10
MS Widows XP Pro 5.1.2600 SP2
BIOS: v 2.60 (updated 2 days ago)
Intel Celeron M 1.60 GHz
496 MB Ram
55.890 GB
Video: Intel 82852/82855 GM/GME Graphics Controller ver=6.14.10.3929
Sound: Conexant AC-Link Audio
Network: Realtek RTL8139/810x Family Fast Ethernet NIC
Modem: AC97 SoftV92 Data Fax Modem with SmartCP ver=7.12.13.50
IDE Device 1: Fujitsu MHV2060AT
IDE Device 2: None
IDE Device 3: Mat****a DVD-Ram UJ-831S Firmware=1.90
Internet Explorer:
6.0.2900.2180

HT201250 what does reported "error code 6584" mean ?

What does reported "error code 6584" mean ? when trying to get into my time machine back up.

First, I suggest you make another full backup to a locally-attached external hard drive. You should do that anyway. One backup isn't enough to be safe, and backing up over a network is less reliable than backing up locally. Then try each of the following steps that you haven't already taken.
1. Restart the backup device. You can do that by disconnecting and reconnecting the power cord.
2. Open the Time Machine pane in System Preferences and check that the device is selected as a destination. If it isn't, select it and try again.
3. Hold down the option key and select Verify Backups from the TM menu in the menu bar (not the Dock icon.) This operation may take a long time. If the menu-bar icon (a clock that runs backwards) isn't showing, check Show Time Machine in menu bar in the preferences.
4. Erase the backup device. With a Time Capsule, you do that from within the AirPort Utility application; see its built-in help for details. All backups on the device will be lost, so don't do this until you've backed up to another device. After erasing, select the device again as a backup destination in the TM preference pane. The first backup should be made over a wired connection, if possible.

IF Condition in a PL/SQL Script give a report error.

Hello, Im German and I hope you can unterstand my Question.
First, I work with the HTML DB Version 1.6.0.0.0.87 and the Oracle Version 9.2.0.6.
I create a SQL Report, where a PL/SQL Script return the SQL Statement for the Report. This is my source-code, I have short it...:
Declare
sql_str varchar(2000);
sql_str_select varchar(1000) :=' select dim_sparte ... ';
sql_str_from varchar(1000) := ' from faktentabelle,dim_sparte ';
sql_str_where varchar(1000):= ' where and faktentabelle.zeit_id = :POPUP_ZEIT ';
sql_str_groupby varchar(1000):= ' group by dim_sparte.name, faktentabelle.zeit_id ';
Begin
If ( (V('POPUP_NETZGEBIET') is not NULL) and (V('POPUP_NETZGEBIET') <>
'Alle Netzgebiete')) THEN
sql_str_select := sql_str_select || ' ,dim_organisationseinheit.netzgebiet_name ';
sql_str_from := sql_str_from || ' , dim_organisationseinheit ';
sql_str_where := sql_str_where || ' and faktentabelle ... and
dim_organisationseinheit.netzgebiet_name = :POPUP_NETZGEBIET';
sql_str_groupby := sql_str_groupby || ' , dim_orga .... ';
End IF;
sql_str:= sql_str_select || sql_str_from || sql_str_where || sql_str_groupby;
htp.print(sql_str);
Return sql_str;
End;
This Script include a IF-THEN condition. The Condition is true and the sql-String-Variables are updatet.
I can get the string with htp.print() and the Statement is OK.
The report get a Error report error: ORA-1403: no data found. If I copy the printet sql String in a new Report Region with SQL String, the Report is OK. When I write IF(true) instead of IF( Condition) the Report is OK, too.
I try ist with Varibalen V(name) and with :name. Its always the same problem. I cant use IF-THEN-Else Conditions in a Script.
Please help me and say me what is the problem???
Thanks,
Simona

Hi Simona,
In the sql region below the region source see that you have " Use Generic Column Names (parse query at runtime only)" check and not " Use Query-Specific Column Names and Validate Query".
This error you usually get when you have a mismatch in your report heading.
Vivek
[email protected]

History report error: | An Exceptional Error occurred. Application exiting. Check the log file for error 5022

Hi all
I've got a error msg when try to generate a report using Cisco history report tool:
Error | An Exceptional Error occurred. Application exiting. Check the log file for error 5022
It only happens when choose report template: ICD_Contact_Service_Queue_Activity_by_CSQ_en_us.
User tried samething on other PC, it working fine.
only on user' own PC and only choose this report, error appears.
user runing windows 7 and do not have crystal report installed
tried reinstalled the software, doesn't work.
also tried this: (https://cisco-support.hosted.jivesoftware.com/thread/2041254) - doesn't work
then tried https://supportforums.cisco.com/docs/DOC-6209 - doesn't work
attached the log file.
thanks.

wenqianyu wrote:From the log file:Looks like you get a Login Window.Error message showed up after username/password be enteredThere is an error in the log: Error happened in comparing UCCX version and HRC versionYou may need to do a clean uninstall, download the Historical report from the server, and install it again on the PC.Does this only happen to one PC or to every PC with this application?Wenqian
I have completely uninstalled the HRC, and download from server install again -- still doesn't work with exactly same error.
this matter only happens on this PC, when user try same thing on other PC, it works.
so i think it not relate to server or account.

Report error: ORA-06502: PL/SQL: numeric or value error: character string b

I have a form which uses a customer form/report, drop downs etc..
the debug shows it running this statement
...Execute Statement: begin begin SELECT distinct initcap(RTRIM (LTRIM (e.surname, ' *0123456789-/:.?,'), ' *0123456789-/:.?,') || ', ' || RTRIM (LTRIM (e.first_name, ' *0123456789-/:.?,'), ' *0123456789-/:.?,' )) empname, e.ID bulk collect into wwv_flow_utilities.g_display,wwv_flow_utilities.g_value FROM dms.dms_employees@dmsprd e, dms.dms_employee_contracts@dmsprd ec WHERE e.ID = ec.emp_id and e.surname like '%%' AND :p75_date BETWEEN ec.start_date AND NVL (ec.end_date, :p75_date) AND e.brh_id = 3654 ORDER BY 1; end; end;
Then says
"report error: ORA-06502: PL/SQL: numeric or value error: character string buffer too small"
Any Ideas?
Thanks
Dean

Denes Kubicek wrote:
A select list is limited in size. I am not sure what the limit is but that is definitelly the case.The maximum size for the HTML generated for a select list is 32K.
86 options sounds on the low side to be hitting that limit, but there are other concerns to this as well. Scrolling through hundreds/thousands of options in a select list is a pain for users, and huge select lists produce bloated pages that impact load times and network bandwidth. That list of around 200 countries you find on many sites is about the sensible maximum length for a select list.
You should use popups.Indeed.

Report error:ORA-06502: PL/SQL: numeric or value error: character to number

The oracle application express environment is created by installing the HTTP Server on the windows server and the application express 3.2.1 components on the 11.1.0.7 oracle database on UNIX. The installation is successfully and have not seen any issues during the installation. After completing all the steps, when tried to login and click the application builder or workspace components, I see the error message
report error:ORA-06502: PL/SQL: numeric or value error: character to number.
This error message is seen on most of the pages when trying to accessed and not able to understand the reasons behind it. Its a brand new environment setup and not even presented to developers to test it.
Below error message is always seen when trying to access most of the components like application builder, schema comparison and some other tabs. Please advice
report error:
ORA-06502: PL/SQL: numeric or value error: character to number conversion error
Edited by: user589320 on Jun 9, 2011 5:17 PM

I think its better you use APEX 4.x version ratherthan using old version.
You will get more features and some bug fixes and also it's easy for you to get some help when you need.
* If this answer is helpfull or correct then please mark it and grant the points.

Report error:ORA-06502: PL/SQL: numeric or value error: character string bu

We face the above error in HTMLDB (APEX) application Ver 3.1.0. This occurs when we try to display more number of rows/records in drop-down list (LOV in tabular forms). We are able to display 200 records in LOV. When the list of records exceeds 230, we face the below error
report error:ORA-06502: PL/SQL: numeric or value error: character string buffer too small
the values listed in LOV are from tables (one of the columns in table)
Could anyone give us a solution?

Hi
As you are using a tabular form, you could actually do the following:
1 - In the tabular form column's attributes, set the following:
Display as: Select List (query based on LOV)
Display extra values: Yes
List of values definition: SELECT null d, null r FROM DUAL
2 - Add a new page item and set it to generate your select list
3 - Create an HTML region with no template and use the following for its source:
<script type="text/javascript">
function loadList(c, l)
var s = document.getElementsByName(c);
var lItem = document.getElementById(l);
var lLength = lItem.options.length;
var k;
var j;
var x = lItem.innerHTML;
var v;
var o;
var z;
for (k = 0; k < s.length; k++)
z = s[k];
v = z.value;
z.options.length = 0;
for (j = 0; j < lLength; j++)
o = new Option()
o.value = lItem[j].value;
o.text = lItem[j].text;
z.options[j] = o;
z.value = v;
if (z.selectedIndex == -1)
z.selectedIndex = 0;
loadList("f05", "P1_MGR");
</script>
(Change "f05" and "P1_MGR" as appropriate to your column and your new page item respectively)
Now, when you load the page, the select list contains a null entry plus the entry already on the database. The javascript kicks in automatically, loops through every entry in the "f05" column, copies the existing value, replaces the select list with the new page item version and sets its value to the copied value.
Your new page item could be in a DIV tag that has a style of "display:none" to hide it from view.
Andy

Report error: ORA-06502: PL/SQL: numeric or value error: NULL index table k

Hi everybody,
I have two Distinct Databases on two distinct servers. (Oracle Ent. Release 10.2.0.3.0 on AIX 5.3). After I install the latest patch last week, One of the APEX installation has some problems on Home>Application Builder Page. The error message is very random and
report error:
ORA-06502: PL/SQL: numeric or value error: NULL index table key value.
When i change the view (details to icons), everything goes to normal. This error message is reflected some of the pages (report region) of some of my applications randomly. When it appears in a report region, i deselect the order method of the region, the result is normal.
But the other APEX application on the other instance has no problem. It is a bug? or Should i re-install the APEX instance?
Thank you for your interest?
Gökhan ÇATALKAYA

No, but we have a reproducible test case now so we're working on it. See ORA-06502: PL/SQL: numeric or value error: NULL index table key value
Scott

PL/SQL function body returning SQL - report error:ORA-01403: no data found

Hi,
I am working on Application Express 4.0.2.00.06, and 11G database.
I have a problem with classic report area of type - PL/SQL function body returning SQL query. Query works if I define region area as - Use Generic Column Names (parse query at runtime only), and does not when I define it - Use Query-Specific Column Names and Validate Query.
I am getting error:
report error:ORA-01403: no data found
This is my query that is returned from function, and displayed with htp.p, and it works ok and returns data in SQL Developer and SQL Workshop (in Apex).
<code>
/* select 1 from dual */ SELECT SIFPRO, NAZIV, VODITELJ, DATPZA,SUM(DECODE(TJEDAN,'2010/46',BRDJEL,null)) as "2010/46" ,SUM(DECODE(TJEDAN,'2010/49',BRDJEL,null)) as "2010/49" ,SUM(DECODE(TJEDAN,'2010/50',BRDJEL,null)) as "2010/50" ,SUM(DECODE(TJEDAN,'2010/51',BRDJEL,null)) as "2010/51" ,SUM(DECODE(TJEDAN,'2010/52',BRDJEL,null)) as "2010/52" ,SUM(DECODE(TJEDAN,'2011/01',BRDJEL,null)) as "2011/01" ,SUM(DECODE(TJEDAN,'2011/02',BRDJEL,null)) as "2011/02" ,SUM(DECODE(TJEDAN,'2011/03',BRDJEL,null)) as "2011/03" ,SUM(DECODE(TJEDAN,'2011/04',BRDJEL,null)) as "2011/04" ,SUM(DECODE(TJEDAN,'2011/05',BRDJEL,null)) as "2011/05" ,SUM(DECODE(TJEDAN,'2011/06',BRDJEL,null)) as "2011/06" ,SUM(DECODE(TJEDAN,'2011/07',BRDJEL,null)) as "2011/07" ,SUM(DECODE(TJEDAN,'2011/08',BRDJEL,null)) as "2011/08" ,SUM(DECODE(TJEDAN,'2011/09',BRDJEL,null)) as "2011/09" ,SUM(DECODE(TJEDAN,'2011/10',BRDJEL,null)) as "2011/10" FROM (SELECT * FROM PMV_PLAN_TVRTKA) GROUP BY SIFPRO, NAZIV, VODITELJ, DATPZA ORDER BY SIFPRO, NAZIV, VODITELJ, DATPZA
</code>
As you can see, I even tried with workaround that I found on the previous post on the forum, and that is to put /* select 1 from dual */ to start query.
Any help would be appriciated.

/* select 1 from dual */ SELECT SIFPRO, NAZIV, VODITELJ, DATPZA,SUM(DECODE(TJEDAN,'2010/46',BRDJEL,null)) as "2010/46" ,SUM(DECODE(TJEDAN,'2010/49',BRDJEL,null)) as "2010/49" ,SUM(DECODE(TJEDAN,'2010/50',BRDJEL,null)) as "2010/50" ,SUM(DECODE(TJEDAN,'2010/51',BRDJEL,null)) as "2010/51" ,SUM(DECODE(TJEDAN,'2010/52',BRDJEL,null)) as "2010/52" ,SUM(DECODE(TJEDAN,'2011/01',BRDJEL,null)) as "2011/01" ,SUM(DECODE(TJEDAN,'2011/02',BRDJEL,null)) as "2011/02" ,SUM(DECODE(TJEDAN,'2011/03',BRDJEL,null)) as "2011/03" ,SUM(DECODE(TJEDAN,'2011/04',BRDJEL,null)) as "2011/04" ,SUM(DECODE(TJEDAN,'2011/05',BRDJEL,null)) as "2011/05" ,SUM(DECODE(TJEDAN,'2011/06',BRDJEL,null)) as "2011/06" ,SUM(DECODE(TJEDAN,'2011/07',BRDJEL,null)) as "2011/07" ,SUM(DECODE(TJEDAN,'2011/08',BRDJEL,null)) as "2011/08" ,SUM(DECODE(TJEDAN,'2011/09',BRDJEL,null)) as "2011/09" ,SUM(DECODE(TJEDAN,'2011/10',BRDJEL,null)) as "2011/10" FROM (SELECT * FROM PMV_PLAN_TVRTKA) GROUP BY SIFPRO, NAZIV, VODITELJ, DATPZA ORDER BY SIFPRO, NAZIV, VODITELJ, DATPZA

Invoce Aging Report - Error

Hi Team,
I'm trying to run Invoice Aging report. When I'm running this it's erroring out. Here I'm posting log file
Receivables: Version : 12.0.0
Copyright (c) 1979, 1999, Oracle Corporation. All rights reserved.
XXRAXINV_SEL_SE module: XXXXX Invoice Print Selected Invoices OBA
Current system time is 20-JUL-2012 11:05:28
+-----------------------------
| Starting concurrent program execution...
+-----------------------------
Arguments
p_order_by='TRX_NUMBER'
p_cust_trx_class='INV'
p_cust_trx_type_id='1'
p_trx_number_low='10040'
p_trx_number_high='10040'
p_customer_id='10041'
p_open_invoice='Y'
p_check_for_taxyn='N'
p_choice='SEL'
p_header_pages='1'
p_debug_flag='N'
p_message_level='10'
Forcing NLS_NUMERIC_CHARACTERS to: '.,' for XDO processing
APPLLCSP Environment Variable set to :
Current NLS_LANG and NLS_NUMERIC_CHARACTERS Environment Variables are :
American_America.UTF8
Enter Password:
MSG-00100: DEBUG: AfterPForm_Trigger +
MSG-00100: DEBUG: Multi Org established.
MSG-00100: DEBUG: AfterParam_Procs.Get_Country_Details
MSG-00100: DEBUG: AfterParam_Procs.Switch_On_Debug
MSG-00100: DEBUG: AfterParam_Procs.Get_Trx_Number_Low
MSG-00100: DEBUG: AfterParam_Procs.Get_Trx_Number_High
MSG-00100: DEBUG: AfterParam_Procs.Get_Tax_Option
MSG-00103: lp_trx_date_clause = and a.trx_date = a.trx_date
MSG-00100: DEBUG: BeforeReport_Trigger.Build_Where_Clause
MSG-00100: DEBUG: P_Choice: SEL
MSG-00100: DEBUG: Choice is other than ADJ, setting ORDER BY.
MSG-00100: DEBUG: AfterPForm_Trigger -
MSG-00100: DEBUG: BeforeReport_Trigger +
MSG-00100: DEBUG: BeforeReport_Procs.Populate_Printing_Option
MSG-00100: DEBUG: BeforeReport_Procs.Populate_Tax_Printing_Option
MSG-00100: DEBUG: BeforeReport_Trigger.Get_Message_Details
MSG-00100: DEBUG: BeforeReport_Trigger.Get_Org_Profile.
MSG-00100: DEBUG: Organization Id: 86
MSG-00100: DEBUG: BeforeReport_Trigger -
MSG-05000: DEBUG: Trx No... 10040
MSG-43749: There is no remit to address defined for country IT and state .
REP-1419: '': PL/SQL program aborted.
REP-0069: Internal error
REP-57054: In-process job terminated:Terminated with error:
REP-1419: MSG-00100: DEBUG: BeforeReport_Trigger +
MSG-00100: DEBUG: BeforeReport_Procs.Populate_Printing_Option
MSG-00100: DEBUG: BeforeReport_Procs.Populate_Tax_Printing_Option
MSG-00100: DEBUG: BeforeReport_Trigger.Get_Message_Details
MSG-00100: DEBUG: BeforeReport_Trigger.Get_Org_Profile.
MSG-00100: DEBUG: Organization Id: 86
MSG-00100: DEBUG: BeforeReport_Trigger -
MSG-05000: DEBUG: Trx No... 10040
MSG-43749
Report Builder: Release 10.1.2.3.0 - Production on Fri Jul 20 11:05:30 2012
Copyright (c) 1982, 2005, Oracle. All rights reserved.
Start of log messages from FND_FILE
End of log messages from FND_FILE
Program exited with status 1
Environment
Application: 12.1.3(OBA)
OS: Linux 5 - 64 bit
Please do the needful.
Thanks
Rk
Edited by: user11157039 on Jul 20, 2012 12:47 PM

MSG-43749: There is no remit to address defined for country IT and state .Troubleshooting Remit To Address in Oracle Receivables [ID 1101855.1]
Transactions Workbench: Field Defaulting Logic [ID 1413565.1]
REP-0069: Internal errorARXAGE Aging 4 Bucket Report Errors REP-0069 Internal Error [ID 1321276.1]
Invoice Aging Report Errors With Rep-1419 Rep-57054 Rep-0069 [ID 1340456.1]
'Aging - 7 Buckets Report' ARXAGSW Fails with ORA-01722 [ID 1061714.1]
R12: Some Payables Reports Not Working. Same Errors In Log File: REP-1419, REP-0069, REP-57054 [ID 818320.1]
Thanks,
Hussein

No data found report error

when i create a report based on a region source query, it displays fine. However the report attributes are weird just displaying column1, column2 and so on as the column details.
When i change the report back to Use Query-Specific Column Names and Validate Query instead of Use Generic Column Names (parse query at runtime only), the report breaks. The error message report error:
ORA-01403: no data found is displayed.
Why is that when i know the report ran successfully with the same query

It's a sql query i use to build the report. I dont know about session states. Here is the source. It searches data across multiple columns using a search textbox that works. The query worked well before the change.
SELECT Issues.Issue_ID, Issues.Title, Issues.Initial_Issue_Description Description, staff.Developer_name Staff_Assigned, Priority_Codes.Priority_Code, Status_Codes.Status_Code,
Systems.SYSTEM, Modules.Module_Name, Sub_Modules.Sub_Module_Name , Issues.Application_Version,
Issues.Date_Logged, Issues.Created_By, Issues.Target_Date, Issues.Tar_Number, Issues.Last_Updated_By, Issues.Last_Updated_Date,
Issues_Responses.Issue_Detail, Issues_Responses.Issue_Detail_Author
FROM USD_ISSUES Issues,
USD_ISSUE_RESPONSES Issues_Responses,
USD_ISSUE_ASSIGN Issues_Assign,
USD_DBINSTANCES DBInstances,
USD_STATUS_CODES Status_Codes,
USD_PRIORITY_CODES Priority_Codes,
USD_SYSTEMS Systems,
USD_MODULES Modules,
USD_SUB_MODULES Sub_Modules,
USD_STAFF Staff
WHERE Issues_assign.Staff_id = Staff.Staff_ID (+)
AND issues.priority_code_Id= priority_codes.priority_Code_id (+)
AND issues.Status_Code_id = status_codes.Status_code_id (+)
AND issues.instance_ID = dbinstances.INSTANCE_ID (+)
AND issues.system_ID = systems.system_id (+)
AND issues.module_id = modules.module_id (+)
AND issues.sub_module_Id = sub_modules.sub_module_id (+)
AND Issues.Issue_ID = Issues_Responses.Issue_id (+)
AND issues.issue_id = issues_assign.issue_id (+)
AND (:P24_SEARCH IS NULL OR
INSTR(UPPER(TITLE) ||'/'||UPPER(PRIORITY_CODE)||'/'||UPPER(INITIAL_ISSUE_DESCRIPTION) ||'/'||UPPER(STATUS_CODE)||'/'||UPPER(issues.CREATED_BY), UPPER(:P24_SEARCH)) > 0)
order by title;;

RAIDXpert reporting errors on nonRAID device

Similar Messages

Maybe you are looking for