Raised Messages Not Appearing In ByDesign

Hello everyone,
Simple question --- I have a message on a custom BO I want to appear in ByDesign should a script successfully run. The message appears with the correct values in the debugger if I have it open, but nothing comes up along the bottom of the screen in ByDesign, whether the debugger's open or not.
I was under the impression that all I had to do was write:
raise MessageName.Create("S", <parameter list>);
And it would appear, but apparently not. The screen in question is the file input screen: I want a message to appear should the file input successfully trigger and run an AfterModify script to completion. Any ideas? Thanks!
Lewis

Hi Frederick,
In order to be able to display synchronous messages in SXI_MONITOR you have to set the following
parameter in SXMB_ADM.
Go to SXMB_ADM --> Integration Engine Configuration. Click on 'specific Configuration'.
Add the following parameter:
Category: RUNTIME
Parameter: LOGGING_SYNC
Value: 1.
Hope this helps you.
Carlos

Similar Messages

ChaRM - Message not appearing in CRM Web Client

Hi
My company is using ChaRM and have ZMCR setup for Change Requests. Due to audit reasons, the requester and approver in ZMCR cannot be the same person.
I have gone into SE91 and access message class SOCM_ACTION_LOG. Here, I have created my new message.
I have then gone into SPRO and setup all the necessary configuration.
And it works perfectly!!!! EXCEPT.....the error message doesn't show in CRM Web Client UI. So the functionality is working fine but obviously we need the message to appear so users no why the change request hasn't changed status.
Firstly, here is my config in SPRO:
And this is what's showing in CRM Web Client:
I have read online that function module CRM_MESSAGE_COLLECT is used to show messages in CRM Web Client. I am not an ABAPer. How does this function module work? What do I do with it? Or is there something else I need to do for this message to show?
Pretty sure my config is spot on so just need some advice on how to get the message to show.
Thanks very much!!!!!!!
Shaun

Hi Shaun,
Did you register your custom messages in the SPRO settings? You need to use Appl. Area SOCM_ACTION_LOG and make an entry in the below tanble for Single Messages;
Regards,
Vivek

Error code message not appearing

Hi,
I tried to create a set of labview error codes codes using tools-> edit error codes. A created a few test errors and saved the file in
C:\Program Files\National Instruments\LabVIEW 2009\user.lib\errors
The file called test-errors.txt appears as follows:
<?xml version="1.0" encoding="ISO-8859-1"?>
<nidocument>
<nicomment>
First error code file Sean
</nicomment>
<nierror code="5000">
Device unstable
</nierror>
<nierror code="5001">
Device Critically Unstable
</nierror>
<nierror code="5002">
Press Stop or device will begin countdown to destruction
</nierror>
<nierror code="5003">
Destruction Countdown Commenced, all organic life will be destroyed with a 2 mile radius in t - 10 minutes
</nierror>
</nidocument>
I then designed a simple VI to test the error codes, see the attachment. However the error message do not appear in the error out source box.
Does anyone know why LabVIEW is not recognising my error codes?
Rgds,
Sean
Solved!
Go to Solution.
Attachments:
test.vi ‏12 KB

Hi Sean,
OK - i took another look at your test VI and probing on the error out wire shows the description, but you are right it is not shown in the control. I have attached a VI that should solve the problem (I have tested it and i works ok)
All I have done is to use the general error handler, which returns the error code and description, write the description to the error cluster and set the general error handler to 'no dialogue' so that the message is not displayed.
Like i say, it works but if there is a better solution let me know!
David
David
www.controlsoftwaresolutions.com
Attachments:
Error cluster from error code (with description).vi ‏13 KB

Why are some inbox messages not appearing in Mail on multiple macs and other devices?

My partner and I have an iMac at home and one at work. We also have two iPhones and two iPads. We only have a couple email accounts each and two for work set up on all six Mail applications. For some reason inbox messages are not appearing consistantly on all six devices. For example, I can have a new message from my Mom, see it at home and on my iPhone, but not on the iMac at work.
Also, some messages I'd like deleted off my work iMac since they're personal, but I'd like them kept on my home iMac and iPhone. Is this possible? Is it possible to delete a message on one and have it deleted on all others?
Message was edited by: witboy

What type of email accounts are they? IMAP or POP.
IMAP leaves messages on the server so you can get them from everywhere.
With POP, messages are downloaded to your client and then removed from the server, depending on your settings.
The iDevice setup for POP doesn't remove them from the server.
I think Mail's default setup for POP is to remove immediately.
If they are POP accounts, you can set Mail's preferences to leave messages on the server for a period of time so that you can retrieve them on multiple clients.

Call Message Not Appearing

Hello!
I was using Skype for a few months, but about a week ago, I noticed a problem. When my friend calles me, I the call message (the blue one at the top right corner) does not appear. When he writes to me, however, everything's fine, and the message appears. I don't know what's the problem, I haven't changed any settings. I'm using Windows 8, and I have Skype from the Windows Store. Please help me.

Having same problem.
While I'm on Audio call, I can send IMs to anyone except the person(s) I'm on call with. If I go to recent chats, when I click on another person I get the chat screen with some previous messages, but when I click the person I'm on call with, I get connection pane, with his profile pic all over the screen.
If that person sends me an IM, then the message appears in blue bubble, and disappears after a while, but I can't see previous messages.

Messages not appearing on mac with mountain lion.

I downloaded ML and have an iphone 4 with up to date OS software. Is there a reason that my messages are not appearing on both? I have enabled messages on both devices, but nothing is transferring over. In fact I think that some imessages are not coming through to my cell phone at all.

You have to set this up a certain way to work.
On your Messages program on your macbook, make sure the account is using the same account as on your iPhone. On your iPhone, go into Messages settings, and make sure you are using your email address (the one from your account) as your caller ID. When you begin an iMessage conversation with someone, it will show up in both.

Group text messages not appearing in messages

I am receiving all one to one text messages on my iPhone and Macbook, but group strings are not appearing on my macbook pro. Am I missing something? I've deleted existing threads from phone, power cycled, and still no joy.

Hi,
I too have the same annoying issue. I have to continuously take out the battery and restart my Q10 in order for my text messages, facebook, and email notifications to come in. This is my second Q10 now as the first one started freezing when I tried sending emails so I thought the Hub problem was related to a faulty phone but now that I have my second one, the same problems are happening (except for the freezing of the phone). It is incredibly frustrating that a phone in this price range has such a basic fault when the main purpose of a mobile phone is to receive phone calls, text messages, and emails!!
I have also found that I have multiple contact details for the same person and that if I try to call someone's mobile that begins with 04 (Australian mobiles) I get told I can't call that number, but if I call a mobile with +61 (Australian country code) I get through to them! The phone also wont save contact details of people who only have a landlines number.
I have been with Blackberry for 6 years now and this is my 4th BB phone. I have always been a staunch advocate of the Blackberry until now. These software issues should not be happening in a high end phone.
Blackberry, please create a fix for these basic issues as soon as possible.
I have a Blackberry Q10; OS version 10.1.0.1910; Build 517312; and Software Update 10.1.0.314
Many thanks

Callback message not appearing on Siemens Hicom connected phones

We have connected two Siemens Hicom 350 PABXs using E1 controllers on two routers. The routers are connected via an IP (over ATM) link. Siemens digital phones are connected to each PABX. Calls are going across smoothly, however, when callback feature is initiated from a phone on one PABX to a phone on the other PABX, the initiating phone shows the message "Not possible" although the callback is actually set and does call back. The message should show as "Will call back".

Ok, the situation now is pretty bright. I think you should have noticed the error in the second debug output. The Cisco has hard time in parsing/decoding the ISDN Q.931 packet and therefore shot an error message.
Could you provide me with the IOS versions of the gateways, or even better - the H323 versions they are running.
For the time being, I would recommend to you to issue the global command "isdn gateway-max-internetworking". With this command the Cisco gateways will try to do their best to pass transparently the unknown ISDN packets without trying to decode them. Let me know if that works.
After checking the H323 version, compiled into your gateway's IOSes, you should see if they are running H323 version 2,3, or 4. AFAIK, 12.3 IOSes are running H323 version 4, which has the ability to "tunnel" QSIG messages over the IP.

Syslog Messages Not Appearing

Hi, I'm hoping someone can help me get my syslog messages to appear when I'm logged into the switch via SSH on a Cisco 4510R Switch. The ones that appear when I shutdown/no shutdown interfaces, leave global config mode, all the basic messages I'm used to seeing when logged in via console, telnet, or ssh.
The show run command displays logging console critical, which is the default of (2) I believe.
In global config, I set logging monitor 2, and also tried both console and monitor at level 5. Nothing is showing up.
Show logging displays all the latest messages, but I'm used to these showing up as things are configured.
This is the way the switch was set up prior to my working here.
Does anyone have any idea why this, and how I can get it working?
Thanks.

According to your configuration guide the default is debugging ie. level 7 so I suspect this has been changed.
In regards to your question if you are logged in via a vty line then you need to change the monitor level but then you may also need to type -
"terminal monitor" or "term mon" for short.
if you want turn it off -
"terminal no monitor"
Jon

Sent messages not appearing on iPad...

Why won't my sent email messages appear on my iPad, or in Mail on my MacBook appear even though they have been sent and received?
(The mail account is configured correctly and this function works on my MacBook AND iPhone but never on my iPad)

I'm still having this issue with 2 different IMAP based web mail accounts...
They both send and receive messages just fine, however on my iPad and iPhone the Sent Messages are never saved, yet on my MacBook Pro and Mac Pro they do. The web ail accounts are set up with the EXACT same settings so I'm not sure why my devices won't save my Sent Messages.
Any suggestions?

Mail & Exchange - Sent Messages not appearing in Sent mailbox

Once setting up an Exchange account in Mail everything seems to be working fine except that when I send any emails they don't appear in the "Sent" folder. When I log in under webmail they do appear. Anyone else find a solution to this problem?
Thanks for any help.
K

I'm having my own share of problems with Mail 4.2 and Exchange Server 2007. See this post.
In addition to the Junk mail problem, I'm experiencing overall sluggishness. Mail takes longer than it should to quit, and sometimes I get the spinning pizza Loading… icon on simple text messages. I wish I could go back to re-configuring my Mail account to be POP instead of the auto discovery Exchange method.
As to the Sent mail problem, I am not experiencing that issue. I don't know if this will help, but go to your Exchange account configuration in Mail, click Mailbox Behaviors, and under Sent check "Store sent messages on the server" and for "Delete sent messages when:" choose Never.
My Sent messages all show up in my Sent folder in Mail, but they take a second. From what I can gather, these messages are sent to the Exchange Server first, and then downloaded by Mail. An unnecessary step, I feel, but I guess that's the way Exchange Servers work.

Sent Messages not appearing in Mail

For the past several days many of my older Sent messages from my Gmail account have not been appearing in the Sent folder in Mail. The most recent messages from sent from Mail appear, but messages sent from other devices that used to appear in the Sent folder within Mail are not showing up. I can view my Sent messges within the Gmail IMAP folders and in my Sent folders in my iPad and iPhone Mail apps. What can I do?

Select the mailbox in the mailbox list, then select
Mailbox ▹ Rebuild
from the menu bar.

Messages not appearing in sent mail folders

We recently migrated from a linux environ to mac server snow leopard. I'm now using Thunderbird as a testbed for my mail client as we have deeply populated mac mail clients that we don't want to disturb if our migration goes bad. Previously, I used both the mail app on mac and Thunderbird as my mail clients depending... Previously, when I would send a msg from my blackberry it would appear in my sent mail folder (on any mail client). Now it does not. Any suggestions as to why? Thanks.

Can you see the sent message when using webmail on the server? If so you may just need to map the sent area of each mail client to the proper folder on the server, assuming you are using IMAP.

New mail messages not appearing in Inbox

Hi there,
I IMAP my email at work using Mail. Sometimes, messages don't appear in the inbpx or Smart folder that I have set up. I have rules for most people which moves teh unread message into their respective mail folder on the mail server. Its only, when I click on a mail folder that the message appears in the folder, the Inbox and the Smart folder.
Any ideas? Is it my mail server or Mail thats is causing this??
regards, Chris

The message that you tried to send is probably stuck in Outbox, but it looks like Envelope Index may have gone awry as well, so let’s re-create both:
1. Quit Mail if it’s running.
2. In the Finder, go to ~/Library/Mail/. Make a backup copy of this folder, just in case something goes wrong, e.g. by dragging it to the Desktop while holding the Option (Alt) key down. This is where all your mail is locally stored.
3. Locate Envelope Index and move it to the Trash. If you see an Envelope Index-journal file there, delete it as well.
4. Move any “IMAP-”, “Mac-”, or “Exchange-” account folders to the Trash. Note that you can do this with IMAP-type accounts because they store mail on the server and Mail can easily re-create them. DON’T trash any “POP-” account folders, as that would cause all mail stored there to be lost.
5. In the Finder, go to ~/Library/Mail/Mailboxes/, locate Outbox.mbox and move it to the Desktop if you want to preserve any messages waiting there, or just trash it otherwise.
6. Open Mail. It will tell you that your mail needs to be “imported”. Click Continue and Mail will proceed to re-create Envelope Index — Mail says it’s “importing”, but it just re-creates the index if the mailboxes are already in Mail 2.x format.
7. As a side effect of having removed the IMAP account folders, those accounts may be in an “offline” state now. Do Mailbox > Go Online to bring them back online.
Note: For those not familiarized with the ~/ notation, it refers to the user’s home folder, i.e. ~/Library is the Library folder within the user’s home folder.

Sent messages not appearing/sent box

I too am finding at times and it seems to be when the message doesn't go out immediately, that it think it goes but doesn't appear in the SENT box although some do receive the message.
I really don't want to BCC myself in everything I send.
Mac mail has given me more problems since July/12 than Outlook did in 10 years.

Hi Bronco_6
What do you mean by .Mac Mail? If you mean using a web browser to access your mail, then by default it does not save items in your Sent Messages folder. This is a Mailbox Behaviour preference that you can set by clicking on the Preferences text at the top right of the web page.
If you are talking about using a .Mac mail account in the Mail application on OS X then that's of course a different issue. It should work by default.
You may mean a combination of both. It took me a while to spot that messages sent via the Web page didn't end up in the Sent folder within Mail.app. Instead they appear in Sent Messages under the .Mac folder.
Hope That Helps.

Raised Messages Not Appearing In ByDesign

Similar Messages

Maybe you are looking for