Ram and SSD upgrade on MB Pro 13.3" 2.4GHz (Model ID: 7,1)

Hello,
I have a MacBook Pro 13.3" 2.4GHz (Model ID: 7,1) and I am looking to upgrade some of the hardware and make it run much faster. I currently am running both Mac OS X and Windows 7 on the computer using Boot camp. I've neglected upgrading the software on the laptop for a while now because I just wasn't using the computer too much due to always using my work computer at the office and using an iPad for the miscellaneous stuff done at home.
Anyway, I first plan to fully upgrade the OS, firmware, all system updates before doing anything and then I would like to upgrade the RAM to 16 GB and potentially put an SSD in there. My question is, can I put an SSD on there as the primary hard drive to really realize the booting speed advantages of an SSD. And can I somehow clone my original hard drive so I can maintain my Windows 7 install on there as well. The point of upgrading is that I'd like to get a home office setup going and need to run MS office apps, Factset, and Bloomberg natively on the windows side for work and also be able to log into Citrix to access work files and with my current setup this slows down the computer significantly. Just wondering if I would run into any problems or if the SSD is not worth the trouble and I should just stick with the RAM upgrade.
Thanks!

Anyway, I first plan to fully upgrade the OS, firmware, all system updates before doing anything and then I would like to upgrade the RAM to 16 GB and potentially put an SSD in there. My question is, can I put an SSD on there as the primary hard drive to really realize the booting speed advantages of an SSD. And can I somehow clone my original hard drive so I can maintain my Windows 7 install on there as well. The point of upgrading is that I'd like to get a home office setup going and need to run MS office apps, Factset, and Bloomberg natively on the windows side for work and also be able to log into Citrix to access work files and with my current setup this slows down the computer significantly. Just wondering if I would run into any problems or if the SSD is not worth the trouble and I should just stick with the RAM upgrade.
You can fit an SSD and there will be a significant performance increase.
I suggest that you first (using WinClone) clone the Windows installation to an image on the OSX partition, then (using CCC) clone the Mac partition to the SSD (assuming there is enough space). Then use WinClone to restore the Windows partition.

Similar Messages

Ram and ssd upgrade for v5 572pg recommendations please

hi all , im running lightroom 5 and photoshop cc with my current acer v5 572pg it has 4gb ram i want to add 8gb im guessing i will have 12 gb of ram then i also want to add a 500gb ssd drive can someone please give me links to the right drive and ram upgrade my budget is around 400 dollars any help greatly appreciated also if i add a new drive what process do i need to do to install windows , i have windows 8.1 on my drive now and looking to upgrade to windows ten soon so i thought a new ssd drive before i upgrade would be the best way to go , can i install it by adding the drive to a usb slot and making the windows ten upgrade go onto the new ssd drive then replace the old drive with the new ssd one with windows ten on it problem im having is my disc always seems to be 100 percent or gets there just by opening up any program or web page , it does settle down a bit but lightroom and photoshop both put heavy pressure on

looking at these two Samsung 8GB DDR3L RAM PC3L-12800 DDR3 1600Mhz 204pin Laptop Memory SODIMM 1.35v and a samsung 500gb evo , are these compatible with the acer aspire v 572 pg , it has software to transfer the old hard drive over , will this include the operating system and then do i just take out the old one and put the new drive in , will windows then boot , im thinking then i can do a clean install of windows and transfer all my files and programs back from the old hard drive using the sata to usb adaptor

RAM and SSD upgrade

I have two questions about my dv7-6b77dx.
1) RAM Upgrade:
I want to upgrade my memory to 4+4 from 2+4. Do I have to get the same exact 4GB RAM (CPU-Z says it's Samsung M471B5273DH0-CH9) or can I get any 4GB RAM? I'm asking this because I'm not sure if the two modules have to be identical for dual channel memory. Also, new Samsung models are 30nm with less power consumption while my 4GB is 40nm. Would that be a problem if I connected a 30nm and a 40 nm?
2) SSD:
I want to make sure AHCI is enabled for the new SSD. I googled it and it says it should be configurable in the BIOS but my BIOS doesn't have that sort of a setting. My processor is Core I7 2670QM and I couldn't get anything about the chipset from CPU-Z other than "Intel". How can I enable AHCI or check if it's enabled?
Thanks a lot!
This question was solved.
View Solution.

burqq wrote:
I have two questions about my dv7-6b77dx.
1) RAM Upgrade:
I want to upgrade my memory to 4+4 from 2+4. Do I have to get the same exact 4GB RAM (CPU-Z says it's Samsung M471B5273DH0-CH9) or can I get any 4GB RAM? I'm asking this because I'm not sure if the two modules have to be identical for dual channel memory. Also, new Samsung models are 30nm with less power consumption while my 4GB is 40nm. Would that be a problem if I connected a 30nm and a 40 nm?
If you want a memory upgrade to work the first time it is installed always purchase and install a matched pair of identical modules. Don't mix and match manufacturers or modules of different capacities or configurations.
2) SSD:
I want to make sure AHCI is enabled for the new SSD. I googled it and it says it should be configurable in the BIOS but my BIOS doesn't have that sort of a setting. My processor is Core I7 2670QM and I couldn't get anything about the chipset from CPU-Z other than "Intel". How can I enable AHCI or check if it's enabled?
The installed chipset is the Intel HM65 Express chipset. Your notebook does support SSD drives. Normally you can verify that ACHI is being used by checking the BIOS configuration. It is unfortunate, but an HP BIOS does not gve you the ability to configure SATA as IDE (emulation) or AHCI. You can use a free utility called PCWizard 2010 to see what disk controller is installed and the mode it is operating in. The following image is from within Windows 7 and the PC is a desktop with a ASUS Crosshair IV Formula motherboard
Thanks a lot!
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Upgrading RAM and SSD on MacBook Pro 15" mid 2009

Hey,
I want to upgrade RAM and SSD on my macbook pro, identifier 5,3, and I want to make sure the parts I picked will be compatible with my Macbook.
I'm specifically not sure about its support of 512GB.
I thought about RAM:
http://www.amazon.com/Crucial-PC3-8500-SODIMM-204-Pin-CT2K4G3S1067M/dp/B008LTBJF M/ref=sr_1_1?ie=UTF8&qid=1420487078&sr=8-1&keywords=DDR3+PC3-8500
SSD:
http://www.amazon.com/Crucial-MX100-adapter-Internal-CT512MX100SSD1/dp/B00KFAGCU M/ref=sr_1_1?ie=UTF8&qid=1420486598&sr=8-1&keywords=CT512MX100SSD1
Thanks!

" I have also created a back up on Time Machine (I think I did)."
Check this out:
http://macintoshhowto.com/repair/back-up-computer.html
Once you think you've done it correctly restart and hold down the option key or go to "System Preferences" under the Apple and look at "Startup Disk".
That will tell which Disks are bootable.
Now about that Crucial drive:
http://forum.crucial.com/t5/Crucial-SSDs/512GB-M4-and-2009-Macbook-Pro/td-p/7805 6
It's not clear to me that this issue was resolved. The last post goes nowhere!
I always use OWC:
http://eshop.macsales.com/shop/SSD/OWC
Just did two including this MacBook Pro early 2011 13" and a 2012 Mini. Total no-brainer! The way I like it.

Early 2008 Macbook Pro Should I upgrade to 6gb ram and SSD?

In the last few months, I've entered the world of 64-bit computing. I learned that this now means that my Early 2008 Macbook Pro, that has been fantastic and flawless for 6 years, needs an upgrade or replacement. I'm hard-hard stuck on whether I should upgrade it or replace it.
My current configuration is:
Processor 2.4 GHz Intel Core 2 Duo
Memory 4 GB 667 MHz DDR2 SDRAM
Storage 200 GB SATA Disk
I need to run OSX Mavericks and Windows 7 in VMWare or Bootcamp (I don't really like bootcamp).
I am eyeing two upgrades
1) Crucial 4GB Single DDR2 667MHz (PC2-5300) CL5 SODIMM 200-Pin Notebook Memory Module CT51264AC667
http://www.amazon.com/gp/product/B001RB21JY/ref=ox_sc_act_title_2?ie=UTF8&psc=1& smid=ATVPDKIKX0DER
2) Crucial M500 240GB SATA 2.5-Inch 7mm (with 9.5mm adapter) Internal Solid State Drive CT240M500SSD1
http://www.amazon.com/Crucial-2-5-Inch-adapter-Internal-CT240M500SSD1/dp/B00BQ8R M1A/ref=sr_1_10?s=pc&ie=UTF8&qid=1392961391&sr=1-10&keywords=ssd
My question is: Is it worth it for me max out my computer by upgrading again for $250? Will this hold me over for another 2-3 years, or should I look to replace?

Well, I have researched and researched and researched and come to a conclusion. I've compared many brand new replacement computers, and also reviewed my options for upgrading my computer. Upgrading to a new computer altogether, I have come across a few very attractive offers, but they're all in the $800+ price range.
I've decided that OSX Mavericks is my main issue. My early 2008 Macbook Pro was 100% perfectly sufficient for everything I needed it for when using OSX Snow Leopard. After the upgrade, VMWare Fusion runs like a sloth and everything else runs like a slug (maybe a slug that had a 5 hour energy...). Seriously. Just now, I am running Safari and MS Word while copying files to my backup drive. The beachball is all over the place, whereas the CPU is only at 15% use and RAM is at 3.97/4.00. I'm barely using the computer, and it's ridiculously hot and the fans are screaming.
First thing I'm going to do is 'upgrade' back to Snow Leopard to recover my RAM and regain the ability to effectively run my VMWare virtual machine. Then, I'm going to opt for the $100 upgrade to total 6GB of RAM and $150 upgrade to a SSD.

Non-Apple SSD upgrade of MacBook Pro and trim enabling

Hello.
I have a question about non-Apple SSD upgrade of MacBook Pro. I was planning to go and buy an SSD in a couple of days but I have coincidentally come up with a web page mentioning trim enabling to extend SSD life on MacBook Pros. Actually the article suggested that if trim is not enabled, the SSD performance degradation will start very quickly due to a high number of writing and deletion of data to the same location on the SSD. Apple's original SSDs are really expensive, I checked that. Is there anyone who upgraded with a non-Apple SSD and did not enable trim and realize the SSD performance degradation? Is there anyone who could easily enable trim and is using his Mac efficiently with a non-Apple SSD? I will be glad if you could share your experiences. I really want to improve the speed of my Mid 2012 13 inch MBP but I have to be sure before doing that. I am also planning to buy a Samsung Evo 840 250 GB SSD.
Regards and thanks in advance,
Bugra

Yes you need to install and run TRIM Enabler after your OS X is installed or reverse cloned onto the GUID/OSX extended Journaled formatted SSD from a external boot clone drive of the previous internal drive.
Also you need to run it after some OS X updates and of course upgrades, you'll notice the immediate performance drop if you don't.
It's available over at MacUpdate.com, you'll have to right or control/alt key click to "Open" it to bypass OS X Gatekeeper.
Read these user tips, you can clone your present internal drive to the new SSD using a SATA to USB adapter/Carbon Copy Cloner (not Superduper) and then reboot and hold option/alt key down on a wired keyboard to boot from it and test before making hardware switch.
Make a bootable clone of your boot drive
Upgrading Your MacBook Pro with a Solid State Drive
Install/upgrade RAM or storage drive in Mac's
Of your going the fresh install or + TimeMachine restore route, then also read this
Reset your Mac

Upgrading RAM and SSD on hp pavilion g6 2005ax

Hey guys,
I have hp pavilion 2005 ax laptop i want to upgrade ram and SSD i have one slot unused i want to know which ram should i go with.
Corsair DDR3 8 GB
Corsair Vengeance DDR3 4 GB
or if there is any other ram please provide me detail.
Also this is my cpu-z report
will this both ram will work at 1600mhz and compatible with my board ?
Should i add one ram to existing or replace it with two ?
what is max size i can upgrade for RAM ?
Will this SSD would be compatible?
Samsunng evo 840
Crucial MX100
i am guessing both will be compatible with my laptop but the main problem is ram and it's frequency i can't seems to find a way.
Please help.

Hi,
Your machine currently has 4Gb of RAM:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c03325481
It supports 8Gb max. CPU-Z (SPD tab) should show you RAM information including brand. You can work out what do you need using that information. My suggestion: use information on the SPD tab INCLUDING brand.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

U400 - adding ram and SSD

Is it possible to add ram and SSD to the U400 by user or if it can only be done by service? I would really want to have 8Gb of ram and the SSD but there is no available model with such config at the moment.

My user-upgrade experience is not good. Most of this is user (my) error, there is nothing wrong with the way the machine was supplied from Lenovo.
I found a YouTube video about cracking the case open and that is what I did, cracked the mount fittings in the front of the case. I got it back together but the front edge is not as secure as it should be.
If you decide to open the case, make sure you SLIDE, don't pry or lift the bottom off after removing the 2 feet screws at the back.
Second bummer is the hard drive is right next to the USB3 port. Everything fits fine w/ the supplied hard drive because the case is slightly recessed on a normal (spinning) disk. On the SSDs I've purchased, the case is the full rectangular size and doesn't fit in opening. I had to hack into the surround of the SSD to make it fit.
Needless to say, I hope I don't need warranty support on the machine or drive.

T400 rams and ssd compatibility

Hi all
I am planing to upgrade the ram and hdd for my laptop lenovo t400 .
Could u pls help me to know what is the ram and ssd that compatible with lenovo t400 ??
Note : i tried to upgrade the ram for lenovo t400 with bus 1333 pc-10600 but that not work .
Kindly advice .
Regards
Solved!
Go to Solution.

RAM = 1066 mhz 204 pin SODIMM DDR3 (although faster ram is also possible, so 1333 mhz and 1666 mhz DDR3 is also okay). But don't use Corsair ram to avoid incompatibility issues.
SSD = SATAII (Although SATAIII is also backward compatible), 2.5 inch, 9.5/7 mm thick drives.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Satellite S55t-B5152 Ram and HD upgrade, please

I just bought a brand new Satellite S55t-B5152 from Microsoft Store. It came with 4GB ram and 512 HD. I have some extra rams and SSD. So I want to upgrade them by myself. unfortunately when receive the laptop, I regconize that the bottom cover is not easly remove, and I research the menual online, it state they are "not user upgradeable, factory installed only". But I did some research on the forum. It seems if you could get a upgarde guide, you may still do it by yourself. So I would ask these Moderators do me a favor, please PM the upgrade guide, so I can do the upgrade by myself. Thank you!

I could not find any guides after searching for many days. So I decided to go ahead and opened up the case. It was quite simple. First I removed the two crews circled in the image below, pulled out the battery, press the power button to make discharge any remaining power.Then I removed the other screws (12 total). Then pried out the cover piece starting from the corner where the power cord plugged in, and go around as showned by the arrows. The pieces were held together by small clips, if you are carefull, I don't think you will break any of them. I just add another piece of RAM, and it popped right in. Not sure how hard it will be to replace the HDD. I though Toshiba has their own RAM, but the one in there is a Kingstons (the blue piece in the picture below). Maybe they sell refurb as new? If you open your case and see a toshiba RAM, please let me know. I installed a 8M in there with the original 4M. OS reports 12M, but when I ran a few RAM tests using the app came with W8.1, the process hanged every time. Maybe some compatible problems. Hopefully, taking out the 4M will solve it. Hope this help.

I am looking to make the switch from pc to mac and have been eyeing the MBP 13". I would like to know whether it is fine to add RAM and SSD myself? any compatibility or warranty problems? what brand/type of RAM and SSD is the best fit? thank you.

i am looking to make the switch from pc to mac and have been eyeing the MBP 13". I would like to know whether it is fine to add RAM and SSD myself? any compatibility or warranty problems? what brand/type of RAM and SSD is the best fit? thank you.

Chamar wrote:
I'm possibly wrong here but I suspect opening a brand new MBP to add parts yourself will void the warranty. It is probably in the small print. I certainly would not risk it for an expensive Apple product.
Some (Windows) laptops have easy access to memory and disk slots that do not necessitate taking the complete back cover off. However, Apple does not make life easy for you.
However, if you are going for a 'used' machine it is probably worth a try.
Not possibly, definitely wrong, Ram and Hard Drive are considered user replaceable and will not void the warranty if changed.

Should I keep my MacBook Pro or exchange it for more Ram and SSD space?

Hello,
I decided to purchase a MacBook Pro 15 inch with Retina display. I thought I would just bite the bullet and get it with the upgraded 16gb Ram and 512 SSD as I want this computer to last me at least 5 years. I don't know exactly what I will be using it for but potentially I will be running a small business with it as well as using it for photos, some videos and all the other things we all use everyday. This brought the total price tag up to about $2900 before tax. Way more than I wanted to spend, but again, I plan on this being my last computer purchase for at least 5 years...and this would be my only computer...not a secondary one but the primary one.
As I was asking the guy in Best Buy about any sales or discounts, he mentioned a MacBook Pro with retina display that was just retuned to the store by a lady that decided to go with a MacBook Air instead. It had been opened but not used and was in perfect condition. The sales manager said he could sell that one to me for $470 off the normal price. The problem was, it was the base model and only had 8gb Ram and 256gb SSD storage. So, I had the option of buying the computer I wanted...that I know would last me for years and years, for $2,900 OR buy the base model for $1,729. What would you do?
I decided to buy the base model as it was just to good a deal to pass up. Now, 2 days later, I don't know if I made the right decision. I know that 256gb of memory is not going to last me very long...especially considering how much more space modern software takes up nowadays...and its only getting worse. My solution is to just buy an external hard drive and store everything I don't immediately need on it. But I don't know if I'm being realistic as maybe it will be a major pain to constantly have to carry around an extra storage device. Then again, even if I had the 512 SSD model MacBook, I would still eventually run out of space and need an external drive. Has anyone else relied on an external device for their daily computing needs? Is it a major nuisance or easy to get by with?
My bigger concern is that it only has 8gb of Ram and can NOT be upgraded in the future. 8gb ram is fine right now, especially with the flash drive and i7 quad core processor, but in a couple years, I'm afraid it won't be enough and that ill be forced to purchase another computer. The sales manager said that because its a Mac and because of the "monster processor" that the 8gb of Ram will be more than enough for years to come. According to him, Macs require less Ram than PC's due to their operating system being much more efficient. (This is my first Mac so I'm a bit unfamiliar)
So this is my dellima, should I return the base model and buy the one I originally wanted or should I make do with the base model and be thankful for the great deal I was able to get?
Will the 8gb of Ram be enough in a few years? I realize that depends on what I'm using the computer for but, since I'm not sure what my needs will be in the next year, lets assume I'll be using it to run a small business as well as the typical storage of pictures and home videos, etc.
Bottom line, will the 8gb of ram be enough to prevent the need to buy another computer for another 5 years or so or do I need to suck it up, return the base model, pay the extra $1,100 and get the 16gb of ram I originally wanted?
Sorry for the long story, I just need some solid advice as money is tight and I want to make the right decision. I'd rather pay $1,100 extra now and not need to buy a new computer for 5-6 years than save the money now but have to buy a whole new computer in 1-2 years. If however, the 8gb ram will still make for a solid computer in a few years, I will gladly save the money.
Thanks in advance for your help. ;-)

Generally (and in my opinion):
1) do not buy any computer you cannot replace the hard drive and the RAM in.
2) do NOT (EVER, EVER, EVER) purchase RAM or expended hard drive from any vendor (like Apple, Dell, etc). they mark up the RAM
purchase the lowest machine that will work for you and upgrade the RAM and hard drive down the road. Just look at the price Apple charges for the upgrade from 4GB to 8 GB:
Apple is charging the (4GB RAM + $100) for the 8GB upgrade. You can easily get 8GB for $100. later you should be able to get 8GB for $60.
Same thing for the hard drives:
Applis charging the price of (500GB + $100) for the 750GB drive. I just bought a 750GB notebook drive for $99
I, personally, would return the retina notebook for a MacBookPro that you can upgrade the hd and ram

Upgrade 2009 base line Mac Mini with aftermarket RAM and SSD!

Hello people,
I'm looking to buy a 2009 Mac Mini (base line, 120GB hdd and 1GB of RAM) and was looking to upgrade it with aftermarket RAM (http://corsair.com/products/mac/default.aspx ) to 4GB (2x2GB) Corsair and with an Intel X25-M SSD, most probably an 80GB drive.
And now comes my question: Based on your experience do you know a better match of aftermarket memmory and SSDs with the Mac Mini?!
Also i've read that using an Intel SSD X-25M to hook up an Windows XP machine (either bootcamp or VM) is impossible since Windows XP doesn't recognize the SSD. Is this correct? (I need XP in VMware to access an old app that's windows based only, and NO wine sadly doesn't work).
Thank you,
Andrei

Well, the big drawback on the Minis is Intel integrated Graphics.
iMacs & Minis run far too hot in my Opinion, Apple likely tested them in a 68° F. air conditioned room.
I myself would be looking into an older iMac, or Widows PC!
iMac "Core i5" 2.5 21.5-Inch (Mid-2011)... Geekbench: 7241/7970
iMac "Core i5" 2.7 27-Inch (Mid-2011)... Geekbench: 7844/8565
iMac "Core i5" 2.7 21.5-Inch (Mid-2011)... Geekbench: 7890/8647
iMac "Core i7" 2.8 21.5-Inch (Mid-2011)... Geekbench: 10248/10690
Mac Pro "Quad Core" 2.66 (2009/Nehalem)... Geekbench: 8269/9237
iMac "Core i5" 2.9 27-Inch (Late 2012)... Geekbench: 9225/10271
Mac Pro "Eight Core" 2.8 (2008)... Geekbench: 9162/10564
Mac Pro "Quad Core" 3.2 (2010/Nehalem).. Geekbench: 9850/10440
MacBook Pro "Core i7" 2.5 27" Late 2011... Geekbench: 10706/11699
Mac mini "Core i7" 2.6 (Late 2012)... Geekbench: 11367/12807
iMac "Core i7" 3.4 27-Inch (Mid-2011)... Geekbench: 11648/12651
Mac Pro "Eight Core" 2.26 (2009/Nehalem)... Geekbench: 11864/13363
Mac Pro "Eight Core" 2.66 (2009/Nehalem)... Geekbench: 14317/16093
Mac Pro "Eight Core" 2.93 (2009/Nehalem)... Geekbench: 15572/17619
Mac Pro "Twelve Core" 2.66 (2010/Westmere)... Geekbench: 20294/22605
iMac "Core i5" 2.7 21.5-Inch (Late 2012)... Geekbench: 8068/9145
Mac mini "Core i7" 2.3 (Late 2012)... Geekbench: 10626/11825
iMac "Core i7" 3.1 21.5-Inch (Late 2012)... Geekbench: 12490/14143
iMac "Core i7" 3.4 27-Inch (Mid-2011)... Geekbench: 11648/12651... Geekbench: 12857/13772

10.6, quicktime, and itunes on a macbook pro 2.53 w/ 4gb ram and ssd

Hi,
I am experiencing something extremely weird, and extremely frustrating...
What I am experiencing is that after I've been using my system for a while, I will launch quicktime, and I will get the spinning ball forever.. If I launch iTunes it will just bounce on my dock forever and not launch.
Then I have to reboot, which is sometimes impossible to do, so I will have to manually tell my system to shutdown via the terminal.
When my mac reboots, everything is fine.. Quicktime launches, iTunes launches, happy world...
... So I thought it was perhaps something that I was doing (applications that I was running, websites I was visiting etc.), but now I have evidence that it's not. Which is even more confusing. Last night, a friend wanted me to pull up something on quicktime-- I got the spinning ball.. Said "ugh, I don't understand what is up with my system". Clicked restart.. It wouldn't restart.. lauched terminal.. sudo shutdown -h now... Ok.. it's off.. turn it on.. Launch quicktime.. hooray.. there's the video..
Ok-- That was the extent of me using my computer. I left it on after that for many hours.. and eventually closed the laptop.
In the morning, opened it up.. Clicked quicktime, and.. SPINNING BALL. Had to reboot.
so, the only thing I can think is that something is occurring inactivity, or sleep, something that is causing QT and iTunes to mess up... I tried doing various tests, but could not come up with anything. I tried just running my screensaver for a while, but quicktime still comes up no problem.
Very frustrating.. I want to know if anyone else is experiencing this, and if there are any suggestions for what I should do. I have zapped p-ram, I have repaired permissions...
-patrick

Welcome to Apple Support Communities
1. That's a risk, and more in a MacBook Pro, that has got everything soldered except the hard drive and memory.
2. If you want performance, buy a SSD. It will get the best performance but they are expensive, so you should consider the option to buy a SSD with a small capacity to store OS X and applications and an external disk for other data.
3. SSDs are much better than hard disk drives because they haven't got mechanical parts. You will notice this difference in read and write tasks like a startup, that will be much faster. However, in other tasks, it doesn't mind if you have a HDD or a SSD, because performance depends on the processor and graphic card. Also, you will notice a difference with a 7200 rpm hard disk.
4. You can take it to an Apple Store or reseller to see what they can do in order to repair your computer

MacBook Pro (summer 2012) non-retina display and SSD upgrade?

Looking to upgrade to a SSD in my MacBook Pro (summer 2012) non-retina display. Are there ones that work better in a MacBook Pro?

In theory at least, any SSD will work fine. There are some additional considerations to make, however. It mostly revolves around updating the drive's firmware. Many SSD companies do not offer Mac-friendly ways to perform this procedure. From the list Clinton provided, you can drop Corsair and Samsung immediately for this reason.
I would not consider OWC, Intel, or any SSD that uses a Sandforce chipset because of spotty reliability. Yes, improvements have been made, but I still do not trust them. Of the dozens of SSDs I've owned and deployed over the last 2-3 years, the only ones to need replacement were ones with Sandforce.
That leaves Crucial, Plextor, and OCZ. The former two basically use the same Marvell chipset. While I can't speak for Plextor, Crucial's firmware updates are OS agnostic. You simply down an .iso file, burn it to CD, boot from that disc, and perform the update. It works perfectly on a Mac. Doing a quick check of Plextor's support site, it seems the proedure is the same.
For OCZ, I'm only focusing on the Vector and Vertex 4. The former is brand new, having just hit the market within the last couple weeks. If you're looking to buy right now, I would stick with the Vertex 4 as it's a more proven commodity. OCZ has created a suite of tools that you copy to a USB flash drive. You can boot from it, and it takes you to what I think is a very heavily modified Linux distribution. From there, you can do a firmware update, check drive health, and perform a SATA secure erase to return the drive to its "out of the box" state. To get the most from the tools, you should have a USB mouse plugged in. Also, firmware updates require the use of a hard-wired Ethernet cable; you can't use wireless.
Bottom line - for an SSD upgrade, stick with Crucial, Plextor, or OCZ as they are the most Mac-friendly (aside from original Apple parts, of course).

Ram and SSD upgrade on MB Pro 13.3" 2.4GHz (Model ID: 7,1)

Similar Messages

Maybe you are looking for