RAM and SSD upgrade

I have two questions about my dv7-6b77dx.
1) RAM Upgrade:
I want to upgrade my memory to 4+4 from 2+4. Do I have to get the same exact 4GB RAM (CPU-Z says it's Samsung M471B5273DH0-CH9) or can I get any 4GB RAM? I'm asking this because I'm not sure if the two modules have to be identical for dual channel memory. Also, new Samsung models are 30nm with less power consumption while my 4GB is 40nm. Would that be a problem if I connected a 30nm and a 40 nm?
2) SSD:
I want to make sure AHCI is enabled for the new SSD. I googled it and it says it should be configurable in the BIOS but my BIOS doesn't have that sort of a setting. My processor is Core I7 2670QM and I couldn't get anything about the chipset from CPU-Z other than "Intel". How can I enable AHCI or check if it's enabled?
Thanks a lot!
This question was solved.
View Solution.

burqq wrote:
I have two questions about my dv7-6b77dx.
1) RAM Upgrade:
I want to upgrade my memory to 4+4 from 2+4. Do I have to get the same exact 4GB RAM (CPU-Z says it's Samsung M471B5273DH0-CH9) or can I get any 4GB RAM? I'm asking this because I'm not sure if the two modules have to be identical for dual channel memory. Also, new Samsung models are 30nm with less power consumption while my 4GB is 40nm. Would that be a problem if I connected a 30nm and a 40 nm?
 If you want a memory upgrade to work the first time it is installed always purchase and install a matched pair of identical modules. Don't mix and match manufacturers or modules of different capacities or configurations. 
2) SSD:
I want to make sure AHCI is enabled for the new SSD. I googled it and it says it should be configurable in the BIOS but my BIOS doesn't have that sort of a setting. My processor is Core I7 2670QM and I couldn't get anything about the chipset from CPU-Z other than "Intel". How can I enable AHCI or check if it's enabled?
 The installed chipset is the Intel HM65 Express chipset. Your notebook does support SSD drives. Normally you can verify that ACHI is being used  by checking the BIOS configuration. It is unfortunate, but an HP BIOS does not gve you the ability to configure SATA as IDE (emulation) or AHCI.  You can use a free utility called PCWizard 2010 to see what disk controller is installed and the mode it is operating in. The following image is from within Windows 7 and the PC is a desktop with a ASUS Crosshair IV Formula motherboard
Thanks a lot!
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Similar Messages

  • Ram and ssd upgrade for v5 572pg recommendations please

    hi all , im running lightroom 5 and photoshop cc with my current acer v5 572pg it has 4gb ram i want to add 8gb im guessing i will have 12 gb of ram then i also want to add a 500gb ssd drive can someone please give me links to the right drive and ram upgrade  my budget is around 400 dollars  any help greatly appreciated also if i add a new drive what process do i need to do to install windows , i have windows 8.1 on my drive now and looking to upgrade to windows ten soon so i thought a new ssd drive before i upgrade would be the best way to go , can i install it by adding the drive to a usb slot and making the windows ten upgrade go onto the new ssd drive then replace the old drive with the new ssd one with windows ten on it problem im having is my disc always seems to be 100 percent or gets there just by opening up any program or web page , it does settle down a bit but lightroom and photoshop both put heavy pressure on

    looking at these two Samsung 8GB DDR3L RAM PC3L-12800 DDR3 1600Mhz 204pin Laptop Memory SODIMM 1.35v and a samsung 500gb evo , are these compatible with the acer aspire v 572 pg , it has software to transfer the old hard drive over , will this include the operating system and then do i just take out the old one and put the new drive in , will windows then boot , im thinking then i can do a clean install of windows and transfer all my files and programs back from the old hard drive using the sata to usb adaptor

  • Ram and SSD upgrade on MB Pro 13.3" 2.4GHz (Model ID: 7,1)

    Hello,
    I have a MacBook Pro 13.3" 2.4GHz (Model ID: 7,1) and I am looking to upgrade some of the hardware and make it run much faster.  I currently am running both Mac OS X and Windows 7 on the computer using Boot camp.  I've neglected upgrading the software on the laptop for a while now because I just wasn't using the computer too much due to always using my work computer at the office and using an iPad for the miscellaneous stuff done at home. 
    Anyway, I first plan to fully upgrade the OS, firmware, all system updates before doing anything and then I would like to upgrade the RAM to 16 GB and potentially put an SSD in there.  My question is, can I put an SSD on there as the primary hard drive to really realize the booting speed advantages of an SSD.  And can I somehow clone my original hard drive so I can maintain my Windows 7 install on there as well.  The point of upgrading is that I'd like to get a home office setup going and need to run MS office apps, Factset, and Bloomberg natively on the windows side for work and also be able to log into Citrix to access work files and with my current setup this slows down the computer significantly.  Just wondering if I would run into any problems or if the SSD is not worth the trouble and I should just stick with the RAM upgrade.
    Thanks!

    Anyway, I first plan to fully upgrade the OS, firmware, all system updates before doing anything and then I would like to upgrade the RAM to 16 GB and potentially put an SSD in there.  My question is, can I put an SSD on there as the primary hard drive to really realize the booting speed advantages of an SSD.  And can I somehow clone my original hard drive so I can maintain my Windows 7 install on there as well.  The point of upgrading is that I'd like to get a home office setup going and need to run MS office apps, Factset, and Bloomberg natively on the windows side for work and also be able to log into Citrix to access work files and with my current setup this slows down the computer significantly.  Just wondering if I would run into any problems or if the SSD is not worth the trouble and I should just stick with the RAM upgrade.
    You can fit an SSD and there will be a significant performance increase.
    I suggest that you first (using WinClone) clone the Windows installation to an image on the OSX partition, then (using CCC) clone the Mac partition to the SSD (assuming there is enough space). Then use WinClone to restore the Windows partition.

  • Upgrading RAM and SSD on MacBook Pro 15" mid 2009

    Hey,
    I want to upgrade RAM and SSD on my macbook pro, identifier 5,3, and I want to make sure the parts I picked will be compatible with my Macbook.
    I'm specifically not sure about its support of 512GB.
    I thought about RAM:
    http://www.amazon.com/Crucial-PC3-8500-SODIMM-204-Pin-CT2K4G3S1067M/dp/B008LTBJF M/ref=sr_1_1?ie=UTF8&qid=1420487078&sr=8-1&keywords=DDR3+PC3-8500
    SSD:
    http://www.amazon.com/Crucial-MX100-adapter-Internal-CT512MX100SSD1/dp/B00KFAGCU M/ref=sr_1_1?ie=UTF8&qid=1420486598&sr=8-1&keywords=CT512MX100SSD1
    Thanks!

    " I have also created a back up on Time Machine (I think I did)."
    Check this out:
    http://macintoshhowto.com/repair/back-up-computer.html
    Once you think you've done it correctly restart and hold down the option key or go to "System Preferences" under the Apple and look at "Startup Disk".
    That will tell which Disks are bootable.
    Now about that Crucial drive:
    http://forum.crucial.com/t5/Crucial-SSDs/512GB-M4-and-2009-Macbook-Pro/td-p/7805 6
    It's not clear to me that this issue was resolved. The last post goes nowhere!
    I always use OWC:
    http://eshop.macsales.com/shop/SSD/OWC
    Just did two including this MacBook Pro early 2011 13" and a 2012 Mini. Total no-brainer! The way I like it.

  • Early 2008 Macbook Pro Should I upgrade to 6gb ram and SSD?

    In the last few months, I've entered the world of 64-bit computing. I learned that this now means that my Early 2008 Macbook Pro, that has been fantastic and flawless for 6 years, needs an upgrade or replacement. I'm hard-hard stuck on whether I should upgrade it or replace it.
    My current configuration is:
    Processor  2.4 GHz Intel Core 2 Duo
    Memory  4 GB 667 MHz DDR2 SDRAM
    Storage 200 GB SATA Disk
    I need to run OSX Mavericks and Windows 7 in VMWare or Bootcamp (I don't really like bootcamp).
    I am eyeing two upgrades
    1) Crucial 4GB Single DDR2 667MHz (PC2-5300) CL5 SODIMM 200-Pin Notebook Memory Module CT51264AC667
    http://www.amazon.com/gp/product/B001RB21JY/ref=ox_sc_act_title_2?ie=UTF8&psc=1& smid=ATVPDKIKX0DER
    2) Crucial M500 240GB SATA 2.5-Inch 7mm (with 9.5mm adapter) Internal Solid State Drive CT240M500SSD1
    http://www.amazon.com/Crucial-2-5-Inch-adapter-Internal-CT240M500SSD1/dp/B00BQ8R M1A/ref=sr_1_10?s=pc&ie=UTF8&qid=1392961391&sr=1-10&keywords=ssd
    My question is: Is it worth it for me max out my computer by upgrading again for $250? Will this hold me over for another 2-3 years, or should I look to replace?

    Well, I have researched and researched and researched and come to a conclusion. I've compared many brand new replacement computers, and also reviewed my options for upgrading my computer. Upgrading to a new computer altogether, I have come across a few very attractive offers, but they're all in the $800+ price range.
    I've decided that OSX Mavericks is my main issue. My early 2008 Macbook Pro was 100% perfectly sufficient for everything I needed it for when using OSX Snow Leopard. After the upgrade, VMWare Fusion runs like a sloth and everything else runs like a slug (maybe a slug that had a 5 hour energy...). Seriously. Just now, I am running Safari and MS Word while copying files to my backup drive. The beachball is all over the place, whereas the CPU is only at 15% use and RAM is at 3.97/4.00. I'm barely using the computer, and it's ridiculously hot and the fans are screaming.
    First thing I'm going to do is 'upgrade' back to Snow Leopard to recover my RAM and regain the ability to effectively run my VMWare virtual machine. Then, I'm going to opt for the $100 upgrade to total 6GB of RAM and $150 upgrade to a SSD.

  • Upgrading RAM and SSD on hp pavilion g6 2005ax

    Hey guys,
    I have hp pavilion 2005 ax laptop i want to upgrade ram and SSD i have one slot unused i want to know which ram should i go with. 
    Corsair DDR3 8 GB
    Corsair Vengeance DDR3 4 GB
    or if there is any other ram please provide me detail.
    Also this is my cpu-z report 
    will this both ram will work at 1600mhz and compatible with my board ?
    Should i add one ram to existing or replace it with two ? 
    what is max size i can upgrade for RAM ?
    Will this SSD would be compatible? 
    Samsunng evo 840
    Crucial MX100
    i am guessing both will be compatible with my laptop but the main problem is ram and it's frequency i can't seems to find a way. 
    Please help.

    Hi,
    Your machine currently has 4Gb of RAM:
        http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c03325481
    It supports 8Gb max. CPU-Z (SPD tab) should show you RAM information including brand. You can work out what do you need using that information. My suggestion: use information on the SPD tab INCLUDING brand.
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • U400 - adding ram and SSD

    Is it possible to add ram and SSD to the U400 by user or if it can only be done by service? I would really want to have 8Gb of ram and the SSD but there is no available model with such config at the moment.

    My user-upgrade experience is not good.   Most of this is user (my) error, there is nothing wrong with the way the machine was supplied from Lenovo.
    I found a YouTube video about cracking the case open and that is what I did, cracked the mount fittings in the front of the case.  I got it back together but the front edge is not as secure as it should be.
    If you decide to open the case, make sure you SLIDE, don't pry or lift the bottom off after removing the 2 feet screws at the back.
    Second bummer is the hard drive is right next to the USB3 port.  Everything fits fine w/ the supplied hard drive because the case is slightly recessed on a normal (spinning) disk.  On the SSDs I've purchased, the case is the full rectangular size and doesn't fit in opening.  I had to hack into the surround of the SSD to make it fit.
    Needless to say, I hope I don't need warranty support on the machine or drive.

  • T400 rams and ssd compatibility

    Hi all
    I am planing to upgrade the ram and hdd for my laptop lenovo t400 .
    Could u pls help me to know what is the ram and ssd that compatible with lenovo t400 ??
    Note : i tried to upgrade the ram for lenovo t400 with bus 1333 pc-10600 but that not work .
    Kindly advice .
    Regards
    Solved!
    Go to Solution.

    RAM = 1066 mhz 204 pin SODIMM DDR3 (although faster ram is also possible, so 1333 mhz and 1666 mhz DDR3 is also okay). But don't use Corsair ram to avoid incompatibility issues.
    SSD = SATAII (Although SATAIII is also backward compatible), 2.5 inch, 9.5/7 mm thick drives.
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • Satellite S55t-B5152 Ram and HD upgrade, please

    I just bought a brand new Satellite S55t-B5152 from Microsoft Store. It came with 4GB ram and 512 HD. I have some extra rams and SSD. So I want to upgrade them by myself. unfortunately when receive the laptop, I regconize that the bottom cover is not easly remove, and I research the menual online, it state they are "not user upgradeable, factory installed only".  But I did some research on the forum. It seems if you could get a upgarde guide, you may still do it by yourself. So I would ask these Moderators do me a favor, please PM the upgrade guide, so I can do the upgrade by myself.  Thank you!

    I could not find any guides after searching for many days.  So I decided to go ahead and opened up the case.  It was quite simple. First I removed the two crews circled in the image below, pulled out the battery, press the power button to make discharge any remaining power.Then I removed the other screws (12 total).  Then pried out the cover piece starting from the corner where the power cord plugged in, and go around as showned by the arrows.  The pieces were held together by small clips, if you are carefull, I don't think you will break any of them.  I just add another piece of RAM, and it popped right in.  Not sure how hard it will be to replace the HDD.  I though Toshiba has their own RAM, but the one in there is a Kingstons (the blue piece in the picture below).  Maybe they sell refurb as new?  If you open your case and see a toshiba RAM, please let me know.  I installed a 8M in there with the original 4M.  OS reports 12M, but when I ran a few RAM tests using the app came with W8.1, the process hanged every time.  Maybe some compatible problems.  Hopefully, taking out the 4M will solve it. Hope this help.

  • I am looking to make the switch from pc to mac and have been eyeing the MBP 13". I would like to know whether it is fine to add RAM and SSD myself? any compatibility or warranty problems? what brand/type of RAM and SSD is the best fit? thank you.

    i am looking to make the switch from pc to mac and have been eyeing the MBP 13". I would like to know whether it is fine to add RAM and SSD myself? any compatibility or warranty problems? what brand/type of RAM and SSD is the best fit? thank you.

    Chamar wrote:
    I'm possibly wrong here but I suspect opening a brand new MBP to add parts yourself will void the warranty.  It is probably in the small print.  I certainly would not risk it for an expensive Apple product.
    Some (Windows) laptops have easy access to memory and disk slots that do not necessitate taking the complete back cover off.  However, Apple does not make life easy for you.
    However, if you are going for a 'used' machine it is probably worth a try.
    Not possibly, definitely wrong, Ram and Hard Drive are considered user replaceable and will not void the warranty if changed.

  • Upgrade 2009 base line Mac Mini with aftermarket RAM and SSD!

    Hello people,
    I'm looking to buy a 2009 Mac Mini (base line, 120GB hdd and 1GB of RAM) and was looking to upgrade it with aftermarket RAM (http://corsair.com/products/mac/default.aspx ) to 4GB (2x2GB) Corsair and with an Intel X25-M SSD, most probably an 80GB drive.
    And now comes my question: Based on your experience do you know a better match of aftermarket memmory and SSDs with the Mac Mini?!
    Also i've read that using an Intel SSD X-25M to hook up an Windows XP machine (either bootcamp or VM) is impossible since Windows XP doesn't recognize the SSD. Is this correct? (I need XP in VMware to access an old app that's windows based only, and NO wine sadly doesn't work).
    Thank you,
    Andrei

    Well, the big drawback on the Minis is Intel integrated Graphics.
    iMacs & Minis run far too hot  in my Opinion, Apple likely tested them in a 68° F. air conditioned room.
    I myself would be looking into an older iMac, or Widows PC!
    iMac "Core i5" 2.5 21.5-Inch (Mid-2011)... Geekbench: 7241/7970
    iMac "Core i5" 2.7 27-Inch (Mid-2011)... Geekbench:           7844/8565
    iMac "Core i5" 2.7 21.5-Inch (Mid-2011)... Geekbench: 7890/8647
    iMac "Core i7" 2.8 21.5-Inch (Mid-2011)... Geekbench: 10248/10690
    Mac Pro "Quad Core" 2.66 (2009/Nehalem)... Geekbench: 8269/9237
    iMac "Core i5" 2.9 27-Inch (Late 2012)... Geekbench: 9225/10271
    Mac Pro "Eight Core" 2.8 (2008)... Geekbench: 9162/10564
    Mac Pro "Quad Core" 3.2 (2010/Nehalem).. Geekbench: 9850/10440
    MacBook Pro "Core i7" 2.5 27" Late 2011... Geekbench: 10706/11699
    Mac mini "Core i7" 2.6 (Late 2012)... Geekbench: 11367/12807
    iMac "Core i7" 3.4 27-Inch (Mid-2011)... Geekbench: 11648/12651
    Mac Pro "Eight Core" 2.26 (2009/Nehalem)... Geekbench: 11864/13363
    Mac Pro "Eight Core" 2.66 (2009/Nehalem)... Geekbench: 14317/16093
    Mac Pro "Eight Core" 2.93 (2009/Nehalem)... Geekbench: 15572/17619
    Mac Pro "Twelve Core" 2.66 (2010/Westmere)... Geekbench: 20294/22605
    iMac "Core i5" 2.7 21.5-Inch (Late 2012)... Geekbench: 8068/9145
    Mac mini "Core i7" 2.3 (Late 2012)... Geekbench: 10626/11825
    iMac "Core i7" 3.1 21.5-Inch (Late 2012)... Geekbench: 12490/14143
    iMac "Core i7" 3.4 27-Inch (Mid-2011)... Geekbench: 11648/12651... Geekbench: 12857/13772

  • Upgrading RAM and SSD versus Purchasing a New MBP

    Hi Apple Community. What are your thoughts on upgrading my mid-2010 MBP with more RAM and an 380 GB SSD HD versus purchasing a new MBP with the faster processor et al? The upgrade would run me about $500, whereas a new laptop would cost me much more. Here are my current specs: 2.4 GHz, 13-in MBP, 4GB RAM and running Mountain Lion. I use my laptop mainly for web browsing, office and streaming music/videos. I don't do much photo editing other than occasionally using Gimp. Thanks for your help!

    For a bit over $600, you could upgrade your particular MBP to 16GB of RAM and a 480 GB SSD and get a remarkable increase in speed. A new MBP would cost about $1,400 more and that's with a maximum of 8 GB of RAM. You'd get a longer warranty with AppleCare with the new one (for another $250). You also have a graphics processor on yours but a new 13" MBP has only the built-in graphics. The only thing I'd miss is the USB 3.0 ports vs the USB 2.0 ports you have.
    Upgrading your current Mac sounds like a speedy and economical choice.

  • Satellite C55-A-1NU - RAM upgrade information and SSD upgrade

    I have a Toshiba Satellite C55-A-1NU and I want to know if is possible to replace the optical drive with a SSD? Can anyone tell me what do I need to do? What kind of rack and SSD should I buy. Thanks
    Also I want to improve the ram memory the laptop has only 1 slot 4 gb ddr3 1600 mhz but is single channel. What model should I buy to work in dual channel I use cpu z to identify the model and it shows me hmt451s6mfr8a do I need exactly this one or I can put 2 of other manufacture ty.

    This upgrade with SSD is not supported by Toshiba so all you do is on your risk. Check please this forum. If Im remembering well some people have already posted own experiences.
    I think in most cases they have ordered such HDD/SSD caddy but disc drive was not recognized at all.
    In my opinion you should not do such upgrade.
    RAM
    According notebook specification you can upgrade RAM up to 16 GB and at the bottom side under memory cover you should find two memory slots. How to upgrade RAM is described in users manuals. Check please page 72.
    Compatible RAM modules for your notebook model are:
    4GB DDR3L-1600 - PA5104U-1M4G
    8GB DDR3L-1600 - PA5104U-1M8G

  • Should I keep my MacBook Pro or exchange it for more Ram and SSD space?

    Hello,
    I decided to purchase a MacBook Pro 15 inch with Retina display. I thought I would just bite the bullet and get it with the upgraded 16gb Ram and 512 SSD as I want this computer to last me at least 5 years. I don't know exactly what I will be using it for but potentially I will be running a small business with it as well as using it for photos, some videos and all the other things we all use everyday. This brought the total price tag up to about $2900 before tax. Way more than I wanted to spend, but again, I plan on this being my last computer purchase for at least 5 years...and this would be my only computer...not a secondary one but the primary one.
    As I was asking the guy in Best Buy about any sales or discounts, he mentioned a MacBook Pro with retina display that was just retuned to the store by a lady that decided to go with a MacBook Air instead.  It had been opened but not used and was in perfect condition. The sales manager said he could sell that one to me for $470 off the normal price. The problem was, it was the base model and only had 8gb Ram and 256gb SSD storage. So, I had the option of buying the computer I wanted...that I know would last me for years and years, for $2,900 OR buy the base model for $1,729. What would you do?
    I decided to buy the base model as it was just to good a deal to pass up. Now, 2 days later, I don't know if I made the right decision. I know that 256gb of memory is not going to last me very long...especially considering how much more space modern software takes up nowadays...and its only getting worse. My solution is to just buy an external hard drive and store everything I don't immediately need on it. But I don't know if I'm being realistic as maybe it will be a major pain to constantly have to carry around an extra storage device. Then again, even if I had the 512 SSD model MacBook, I would still eventually run out of space and need an external drive. Has anyone else relied on an external device for their daily computing needs? Is it a major nuisance or easy to get by with?
    My bigger concern is that it only has 8gb of Ram and can NOT be upgraded in the future. 8gb ram is fine right now, especially with the flash drive and i7 quad core processor, but in a couple years, I'm afraid  it won't be enough and that ill be forced to purchase another computer. The sales manager said that because its a Mac and because of the "monster processor" that the 8gb of Ram will be more than enough for years to come. According to him, Macs require less Ram than PC's due to their operating system being much more efficient. (This is my first Mac so I'm a bit unfamiliar)
    So this is my dellima, should I return the base model and buy the one I originally wanted or should I make do with the base model and be thankful for the great deal I was able to get?
    Will the 8gb of Ram be enough in a few years? I realize that depends on what I'm using the computer for but, since I'm not sure what my needs will be in the next year, lets assume I'll be using it to run a small business as well as the typical storage of pictures and home videos, etc.
    Bottom line, will the 8gb of ram be enough to prevent the need to buy another computer for another 5 years or so or do I need to suck it up, return the base model, pay the extra $1,100 and get the 16gb of ram I originally wanted?
    Sorry for the long story, I just need some solid advice as money is tight and I want to make the right decision. I'd rather pay $1,100 extra now and not need to buy a new computer for 5-6 years than save the money now but have to buy a whole new computer in 1-2 years.  If however, the 8gb ram will still make for a solid computer in a few years, I will gladly save the money.
    Thanks in advance for your help. ;-)

    Generally (and in my opinion):
    1) do not buy any computer you cannot replace the hard drive and the RAM in.
    2) do NOT (EVER, EVER, EVER) purchase RAM or expended hard drive from any vendor (like Apple, Dell, etc).  they mark up the RAM
    purchase the lowest machine that will work for you and upgrade the RAM and hard drive down the road.    Just look at the price Apple charges for the upgrade from 4GB to 8 GB:
    Apple is charging the (4GB RAM + $100) for the 8GB upgrade.  You can easily get 8GB for $100.  later you should be able to get 8GB for $60.
    Same thing for the hard drives:
    Applis charging the price of (500GB + $100) for the 750GB drive.  I just bought a 750GB notebook drive for $99
    I, personally, would return the retina notebook for a MacBookPro that you can upgrade the hd and ram

  • Performance with 2GB RAM and SSD

    I own a late 2010 MBA, 13" baseline model with 2GB RAM, w/SSD.  I am using Snow Leopard, and it runs perfectly.  I would like to upgrade to ML to sync with ipad, but a concerned with performance.  I use my MBA for word processing, emails, and internet surfing, including occasional movie downloads.  I cannot upgrade the RAM on this model.  I would therefore very much appreciate if someone who has run the latest versio of ML on this model can inform me of its performance w/2GB RAM and an SSD drive.  (I know it can run; I want to know how it runs).  Thanks very much!

    Just went through the same situation with my 2006 iMac. Technically my memory tops out at 3gigs, but I can get 4 in there if I insist (though the machine won't take full advantage).
    After a considerable amount of research, and hearing some horror stories of some folks who dove straight into Lion on older machines, I opted on upgrading memory to 3gig, backing up all my data, then running a clean install of Snow Leopard. I then reinstalled all my stuff, followed with a run of Monolingual (a shareware program that removes unnecessary languages and builds), then ran OnyX (another shareware) to run scripts and check/repair permissions.
    Works fantastic. Machine is operating perfectly on 10.6.8 and with the memory upgrade and clean drive its running faster than ever. Definite new breath of life in the machine.
    As per memory upgrade, I'd recommend going to Crucial. They're very Mac friendly, customer oriented, and reasonably priced. They have a small program you can download that scans your machine to determine the correct chip required, then brings you stright to an info and ordering page. I managed to get a 2gig chip with shipping for about $25. With the Snow Leopard upgrade total cost was under $60 for resuscitation.

Maybe you are looking for

  • Quickly fill in blank cells (Excel equivalent)?

    I often import reports from Quicken into Numbers to create data tables for analysis purposes and find that I must fill in blank cells to ensure I have data consistency across rows. While I am confident there is no built in way for Numbers to quickly

  • Hi can anyone help with this Error?

    2.66 ghz i7 8gb macbook pro Interval Since Last Panic Report:  15818 sec Panics Since Last Report:          2 Anonymous UUID:                    7ADC88D6-7016-FF83-E10B-1E9BA6BC146A Sat Apr  6 13:23:24 2013 panic(cpu 0 caller 0xffffff7f99b957f2): NVR

  • FI - AP and GL

    Hi Guys. I am having a call and the requirement is specially focusing on the FI side of ABAP especially GL and AP part of it, so can you please help me with few questions or few topics that I should cover. Thanks, Rajeev

  • Default value at ME21N

    Hi i want account assignment 'K' and item catagory 'D' get default if user selects perticular document type while creating Purchase order. if PO creation date is greater than a perticular date it should be applicable. screen field account assignment

  • Radix Sort - Examining digits

    Hey guys, is there a way to examine the "X" digit within an element of an array? Example: nums[0] = 234 nums[1] = 96 nums[2] = 436 nums[3] = 150 If I wanted to find the "one's" digit in nums[0], how would I do it? We can obviously see that the digit