RAM Settings for 648 Max

Does anyone know what my Cas should be set at while I am using PC2100 DDR RAM. I am using a 648 Max-L

run http://www.memtest86.com on it

Similar Messages

Fastest Compatable DDR RAM For 648 MAX?

I've been reading about all these problems people have been having concerning RAM/motherboard combinations, and have concluded that my RAM is what is causing my problems (XP/2000 installation difficulties, unrecognizable Gainward GF4 Ti4200 card, boot up problems). Right now, I have one Kingston Hyper X 512MB DDR434 RAM (which is going out the door soon) installed on my 648 MAX.
I originally thought the video card problem was BIOS related because the only thing recommended by XP was to update the BIOS (said motherboard does not support your video card's features; try updating your BIOS). I tried that through LiveUpdate, and it messed up somehow during the flash, so I tried to restore the original BIOS, but the system was very unstable after that. I'm about to send my motherboard back for an exchange. I just found out by reading some posts here that other people have been having the same problem with a similar RAM/video card setup.
Also, I'm having extreme difficulty installing Win2000. It installed the first time on a test HDD, but on my new one (WD 80GB 7200RPM ATA100), it wouldn't go in at all. ;( It went up to the final file copying part (after entering the serial number), and crashed. It kept doing that, so I gave up and moved on to XP. XP went in fine the first time, but it wouldn't reinstall after that, even with a reformatted drive. Other people are having similar problems, and said that once they swapped out their RAM, their problems were gone.
I'm just looking for the fastest compatible 512MB DDR RAM available for the 648. Thanks.

Heh, funny thing, I was messing around with some BIOS settings, and somehow got my computer to work this afternoon! 8o Reinstalled everything, and was having a good ol time! :D
Then, and even funnier thing happened. I went out this evening, and when I came back, the computer wouldn't work anymore! X( This thing is driving me nuts. I'm definitely gonna pick up either the Corsair or Winbond memory ASAP. Thanks for the replys everyone!
BTW, I've had the hard drive by itself with the jumperless setting from the beginning. Also, it always wants to be the primary drive, even when it's set to slave and attached at the slave connector on the IDE cable. ?( I know that isn't a problem right now cause I just have it by itself on the cable.

NVIDIA driver 1.13 for 648 max?

while reading this review of sis 648 boards:
http://www6.tomshardware.com/mainboard/20021204/sis648-10.html
I came across nVIDIA driver 1.13 drivers which they appearently used in there testsetup for the chipset. What is this about? Is it some alternative to the sis drivers? Does anyone use it on a msi 648 max and is it any good?

How typical of tom....
They ment SiS AGP 1.13.

RAM settings for BIOS 1.5 (P965 Platinum)

Since upgrading to BIOS 1.5 there now is some extra settings when doing memory timings manually. (SPD disabled)
DRAM TRFC, TWR, TWTR, TRRD & TRTP.
My memory is Corsair XMS2 2048 DDR2 800 6400C4 & I had it set to 4-4-4-12 with BIOS 1.4.
Does anyone know what settings the rest should be set to?
Searched the net endlessly tonight to no avail.

yep, but they are strongly individually depend of memory used. best will be to leave them to default values. or if they must be filled check memory Advanced SPD reading with RMMA (RightMark Memory Analyzer) to findout default values. or just leave them to Auto and then check values assigned with some appl. like Everest.

Help for SIS 648 MAX-L Startup Problem

I just bought an MSI-648MAX-L, a 2.4GHz cpu and a Jaton GeForce4 TI4200 card. Installed all of the above + PC2700 512 MB RAM and a WD 80GB hard drive, floppy and CD. Turn on the power and my screen flickers all four of the diagnostic leds light up green and then nothing. I hear the hard drive spinning and the CPU fan and video card fan but nothing else. Tried one other AGP video card and a PCI video card but nothing on the screen. Seems like the BIOS is not loading. So I turn the computer off and set the BIOS reset jumper. Turn it back on again and still nothing. Checked all the connections, the seating of the CPU and tried again, still nothing. Any idea what might be wrong?? I hope I don't have to buy another MotherBoard and also I hate the idea of removing my CPU once installed. ;(
Thanks for your help..
Kumar.

What kind of video card is it?
If it's a radeon 9700 pro, look in one of the other threads on this site to figure out what revision you have, rev 1.1 or 1.2 9700 pros will not work on some 648 max boards ( well for me it was 648 max L im not sure about the 648 max but im assuming it has the same problem.
What happens with radeon is since the mobo sets the agp automatically, and there is the 8x bug the system doesnt boot. But the card will work fine on machines that have 4x, In this case RMA the card to radeon and make sure to specifiy that you get a 1.3 rev.
Otherwise you stated you have tried other processors and memory that were "known" to be good.
DDR 400 or DDR 333 memory?

What should Ram settings be for FCP 6 doing a slideshow with JPEGS ?

Hi all,
I am doing a Ken Burns effect slideshow in FCP6 that is using JPEGS only.
I have the 24" intel imac 2.4 gig with 4 gigs of Ram installed.
I am wondering what my ram settings in FCP should be.
there are 4 boxes you can fiddle with the numbers.
first two have sliders and go from 0 to 100%
"memory usage"
and also still cache...
what should I be setting these to?
thanks in advance!
I ask because my system bogs right down with only a few layers and effects in place.
what should my sequence settings be as well when working only with JPEG?
I normally edit in easy DV NTSC....

Thanks guys.
I have found that I cannot resize and get a clean movement here in FCP.
I tried the cutting approach jim and that at least got me through the placement of the pics to the song and then I started the motions. I also checked and then unchecked the shadow once I had it set where I wanted. I like to work through each pic from start to finish so i know exactly where I am at each night when I go to bed and then where I start again the next evening after my day job!
haha
but yes unchecking the shadows and feathered edges definately bought me some more time before render.
I appreciate all the helpful advise here. You guys pour so much knowledge out there for us and mostly without even much thanks to you in return.
One question I would still have now that I have fiddled around with all my settings....
would anyone have the time and the knowledge to help me figure out what the "proper" settings should be for my setup for editing regular sd dv ntsc footage?
or when I click easy setup dv ntsc does it configure my system for optimal settings each time?
ie what should my ram settings be?
thanks in advance.
see sig for setup.

Best sysctl settings for a netbook with 1G RAM?

Hi all,
As the title says, what are (based on your experiences) the best sysctl settings for a netbook with 1G of RAM? I now have vm.swappiness=10 and vm.vfs_cache_pressure=50. Should I change these to a lower or higher value? Any other parameters I should add? Let me know!
Thanks for your help.
Luc

karol wrote:https://wiki.archlinux.org/index.php/Ma … M_and_swap
I already read that article, and followed most of it. Should I set my swappiness to 1, then?

Suggested K8T Neo BIOS settings for CL 3 Kingston Value RAM

G'evening!
I'll be putting together a system with the Athlon 64 3000 and K8T Neo board and had a question about optimal BIOS settings for paired Kingston non-ECC DDR 3200 RAM (2x512mb) that's CAS 3. Should have gotten some CAS 2.5 probably but this is what I have for now so in it goes. I'm reading the quick users guide and noticed that you can manipulate the CAS, TCRD, TRAS, and TRP.
First question: Will the board's auto detect do a good job in picking out a stable configuration?
2nd question: If you had to or wanted to make manual settings, what would you suggest? The CAS value is rather easy since I guess it should be set to 3 but what settings would one pick for the others?
And if I still have your attention...
The other things that will be going in the system are the infamous Maxtor 120 gig SATA HD, a XFX 5900FX video card, Lite-On combo burner. Powersupply is an Antec Solution Series 400W PS. After reading the forums for a bit I get the impression that you shouldn't forget to load the SATA Promise drivers so the HD will get recognized. My SATA drive will be the only drive in the system and will of course be the boot drive. Any other possible pitfalls or problems I should know about with the Maxtor SATA's and the K8T Neo board?
Also, I had thought I read from a review that the Zalman Al-Cu CPU heatsink/fan will fit on this board. Of course after seeing it in my hands for the first time I thought that it was a pretty damn big heatsink. Anyone else using this heatsink? (haven't taken it out of the packaging yet so that's why I wanted some impressions).
Thanks for any advice you can give me. It's been a bit of time since I built a computer and I'm sure there's alot of basic things I'm relearning along with the fact that the Athlon 64 is fairly new technology. On the other hand, when it's running smoothly...

Cant offer anything on the Timing, (sorry as I am Intel Fodder ), But I can assure you that the Zalman 7000-AlCu, Will Indeed Fit onto your Motherboard (With Room To Spare!) :biggthumbsup:I can attest to this because My buddy just installed the Zalman 7000-AlCu on his K8T ....And He loves it! As do I ....It's about the only thing that we have in common as far as PC'S Go .........Sean REILLY875

890FXA-GD70 bios settings for my Ram

good day to all, just bought this board and I'm wondering where should i set the base timings for my RAM? where should i put this timings manually 8-8-8-24? i know i have to enter the dram configuration in the bios now i dont know where to continue, sorry just a newbie here , tnx.

How about providing information for your system. It's impossible to say what any RAM settings should be not having a clue what RAM you have. See my signature below for the type of information to provide.
>> Posting Guide <<

KT3V bios settings for Kingston333DDR Ram

Hi all,
I have bought a new RAM Kingston 333 DDR CL2.5 but i do not know the best performance settings from Bios. So can anyone tell me the settings for MSI KT3V bios to increase my performance. I am using a Athlon XP2000+ Cpu.
Thanks all.

Nobody knows? ?(

Cannot restart using 4 RAM Modules on 655 Max HT Ready (MS-6730)

When I use four 512MB RAM modules, my computer starts up and works fine. The only problem is, that I can't restart the it (D-LED boot-error: Memory Failure). To make it run again i have to turn it off and unplug the power cable.
When there are only two RAM modules installed (slot 1 & 3), everything works fine.
What settings do I need to make in the BIOS that it works with all 4 memory modules?
I got four identical and tested Kingmax DDR333 Ram 512MB (MPM33d-383, http://www.kingmax.com/product/pro_deskMPMC22D-38KX3.htm)
my pc-configuration:
655 Max-FISR (6730) v1.0
BIOS A6730SMS v 1.1
P4 2.67
Windows 2000 Pro SP3
4 x 512MB Kingmax DDR333 (MPMC22D-383)
MSI Ti4800SE-VTD
Thermaltake 420W; 3,3V/30A; 5V/40A
Ricoh DVD+RW
Seagate Barracuda ATA V 120GB S-ATA
thanks and cheers

buenas wonkanoby
thanks for your reply. finally i made it work: its this freaky kingmax-ram....
i exchanged two of the kingmax modules by veritech modules and everything works fine now. instead i got problems now with an MSI 648Max-L Board from which i took the veritech memory......
so if anyone else reads this:
[size=15]IF YOU GOT AN MSI 655 MAX OR 648 MAX AND YOU WANNA USE TWO OR MORE MEMORY MODULES GET VERITECH DDR333/512MB (OR WHATEVER) BUT DEFINITELY NOT CRAPPY KINGMAX DDR333/512MB!!! [/SIZE]
cheers and enjoy :D

Skipping sound on 648 Max

I just installed the 648 max board with a 2.4ghz cpu. When I play mp3's or CD's, using the onboard sound, the songs sound like they skip or stutter at random places. Usually happens if I might be moving the mouse, or minimizing, maximizing, opening or closing windows... stuff like that. Then I noticed it would "skip or stutter" even if I was not even making any mouse movements. So I disabled the onboard sound and installed a Sound Blaster Live. Still has the problem but only once in awhile, not as bad as with the onboard. I thought it was the PC Alert that was causing this, but it is not.
Anyone had this problem before? Or any suggestions?
Thanks!

While you're at it also try lower PCI latency timer settings (to keep bus hogs like RAID/IDE controllers in check). The reason for sound skips is that the audio controller has a very limited amout of on-board buffer RAM and therefore relies on constant audio data transfers over the PCI bus - and if something has a very long transfer in progress the bus will not free up in time. (The PCI latency timer defines, in PCI clock cycles, how long a device may lock the bus before giving it up)
Most often this has been a PCI VGA driver issue (where they make use of PCI bursting with very long transfer cycles - this gives them a bit of a performance boost, sacrificing all other users of the bus) - but nothing I've seen with AGP VGA cards...
/WernerJ

MSI 648 Max with AGP X8 - BIOS update

I have replaced my old AGP card with Radeon 9550 256MB for use with my new Dell 20" WS monitor.
Every time, after starting or during 3DMark03, it crashed back to desktop and sometimes retarting my pc. I try ram settings, aperature etc with no luck. My pc has TrueBlue 480 watt PSU and the voltage reading is good.
In the end, I searched this forum and found out it was the problem with AGP X8 so I changed it to AGP X4 via ATI control panel, my pc went through 3Dmark03 with no problems at all. AGP X4 works flawless.
Regarding BIOS - my motherboard is SIS 648 MAX-L HT ready (Hyper-threading) and its latest BIOS version is v3.1. I'm just wondering that is my board exactly the same as non-HT 648 MAX board physically? Since they use same chipset with same layout and also because I noticed the BIOS update for non-HT version is different with v1.5 and has the fix for Radeon 9700 problem which could be related to my problem. Since I'm using Pentium 4 2.53Ghz, Hyper-threading is a useless feature, could I flash my board with this BIOS?
Thanks in advance

Quote from: Stu on 23-September-06, 05:23:39
then leave it at that then. the actual real-life performance difference between 4X and 8X is negligible
Thanks, just asking...I guess I answered my own question!

MSI-6585 (648 MAX) instant restart issues questions pls help......

Hi, i figured after months of specualation i would try to figure out what the hell is wrong with my pc. 12months ago a bought a MS-6585 648 MAX mobo and a P4 2.53ghz with 2x Samsung DDR 333 (PC2700) ram. I play many games on my pc it seems when playing Counter-Strike + PlanetSide results in random instant restarts. Occasionaly it will just hang the system but mainly instant reset of the system. My cpu temp ranges from 35 48 max approx.
I've tried switching my ram to different slots and so on refit everything but with no luck. I just have a very unreliable computer atm. I've reformated plenty of times but with no joy, the odd thing is its random somtimes my pc will not crash or reset it self so this makes it very difficult to figure out what the hell is going on :S
If you have more questions perhaps i can answer them - and give you more info that i have forgotten.
Here are somethings that might be useful:
MS-6585 648 MAX mobo
Pentium 4 (northwood) 2,53ghz 533
Samsung DDR 333 (PC2700)
Gigabyte Maya II Radeon 9700Pro (running in agp 8x)
Sound Blaster Audigy 2 Platinum
Bios settings: (things ive changed)
Turned onboard sound off than auto
AGP Apeture size 128
I have 32bit transfer mode running for hdds
I have S.M.A.R.T. enabled
(next week end i will have another 512 ram stick to try just incase its my ram but i have done the intel ram checker and it didn't find any problems)
Any help would be greatly appreciated pls ask any things ive missed and anything else u would need to know. I really want to sort this out as you can imagine its not very nice having a pc that can randomly crash when u do not expect it.

Overclocking is typically limited by one of 3 factors, assuming you have sufficient power:
1. Memory won't operate past a certain speed, so you run at a different ratio or buy faster memory.
2. Temperature, so you need to add non-stock cooling or better case ventilation or water cooling, depending on how far you want to go
3. CPU - At some point the CPU won't run any faster.
Leave the CPU voltage at Auto. You should only need to raise it if you get into extreme overclocking.
As for the size of the power supply, if you stay with Intel Northwood with an ATX board on your next upgrade, an Enermax 465, Antec 480, or something similar (should cost around $80-100US) would get good choices. If you plan on going with a Prescott on an ATX board, I would look at going to a 550W supply.
Personally, I thing the next 12 months is shaping up to be a real headache in making upgrade decisions in the Intel world. Intel have indicated their next generation of boards will be BTX without AGP support. This looks like an upgrade could mean new case, possibly power supply, video card and possibly ram. I am hoping that companies like MSI will produce a transitional product that allows new processors and chip sets on an atx board. If that doesn't happen I see a lot of people switching to AMD.

MSI 648 Max - Memory question

Hello everyone,
I have an old MSI 648 MAX MB for which I would like to do a RAM upgrade.
I can get DDR400 RAM quite easily, but they are Apacer 512MB DDR400 modules, which do not appear under the list of supported RAM modules.
Does anyone know if this RAM is supported, and if not at DDR400, can the BIOS settings be changed to allow it to run at DDR333?
TIA

Good day,
Here is the specs of the PC:
Processor : Intel(R) Pentium(R) 4 Northwood 2.40GHz
Mainboard : MSI 648 Max (MSI MS-6585)
Memory : 2 x Apacer Technology 512MB DDR400
Video Card : NVIDIA GeForce 6800 AGP
Hard Disk : ST380011A (80 GB)
DVD-Rom Drive : LITE-ON DVD SOHD-167T
CD-Rom Drive : ASUS CRW-2410A
Network Card : Realtek Semiconductor RT8139 (A/B/C/810x/813x/C+) Fast Ethernet Adapter
Operating System : Microsoft Windows XP Professional 5.01.2600 Service Pack 2
PSU : ProCase SH-400WA8/P4
+5V
+3.3V
+12V
-12V
-5V
40A
22A
15A
0.8A
0.5A
I will run MemTest86+ later and report back the results.
Best regards

RAM Settings for 648 Max

Similar Messages

Maybe you are looking for