Ram slots not working after CMOS reset

Im using MSI K9N Neo V2 mb, and it was doing fine until i reseted CMOS. Now 3 out of 4 ram slots are not recognized by BIOS nor Windows. Im sure that ram memory is ok, cause ive checked all of it by replacing it between ram slots, and they're only working in slot nr 4.
I know that the MB is old, but everything was working fine, and suddenly went wrong after CMOS reset
Things i did to fix:
Updated BIOS
Msconfig memory uncheck box
Cleared CMOS with jumper
Replaced CMOS BAT
Checked if smth's wrong with cpu
Cleared RAM slots with rubbing alcohol
System wont even boot without memory in DIMM 4 (ram slot 4), and BIOS only recognizes memory in DIMM 4
This is really frustrating, because there is no reason for smth to not work all of a sudden
Any help? Tnx
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

There is a known issue with Powerbooks with the lower memory slot failing, and it sounds like yours may be starting to fail. At one point there was an Apple recall for a small sliver of Powerbook systems to fix that.
The alternatives are to run with 1GB in the upper slot, try one of the internet vendors that say they can fix that (check references), or install a used logic board. I don't believe Apple is repairing Powerbooks anymore, so if you want to buy a used logic board, you'll need to install it yourself, or perhaps an Apple Authorized Service Provider would be willing to do the work.

Similar Messages

Restore not working after a reset?

Due to problems with some apps I had to reset the iPhone three times now.
After the restore of the iPhone software iTunes asked me if I want to restore the last saved backup. I agreed. But after some scanning the restore failed saying that is is the wrong version.
Anyone an idea? And what is the purpose anyway when restore is not working after reinstalling the iPhone software.
By the way: I have the latest versions of iTunes and the iPhone software.

Izit software or hardware? Confuse:(
Only can use wifi now.
Any way thanks guys for ur suggestion:) amishcake and simes

MSI-7125 K8N neo4f ram slots not working

I have had this motherboard for a little over a year and a few days ago I was on the internet got up for a minute came back and the display was black, I reset the computer and it wouldn't come back on so I disconnected the power cable opened the case and started looking around and couldn't see any physical problems with the board so I took the Video card out, then the ram disconnected the hard drives and optical drives I cleared the CMOS by taking out the battery and leaving it disconnected for 20 minutes,after that time I reinstalled all the components and pushed the power button you could hear it botting up the hard drives and optical drives all the fans were running but no display, So I thought to myself check the ram I started trying different ram slots and there it is the only slot that would work with a single stick of ram was slot #2(purple) and the only slots that would work for 2 sticks were both of the purple slots, I had read the manual and this was very strange considering it say's not to install ram into the purple slots while the green ones were not in use, I am not sure why this just started with no warning I have always use the first 2 slots since I purchased this and never had a problem with this motherboard except for my North bridge fan starting to slow down I replaced it before it quit working other than that I haven't done anything else to it. I would extremely appreciate it if someone could help me out with this problem sorry for such a long post.
THOMAS

Well I've been working on computer's professionally(for place I worked) and privately tried supplemented my income for a while, and most of the problems I seen was either memory related or OS related, I know it wasn't my OS been running fine for a month or so after re-format and just figured it had to be ram related and started checking it out and I was correct . Although I never seen this problem before and that it is aggravating( I just received an email from MSI) and it said I was at the end of my 3 year warranty and that it will cost me $45 bux for them to check it out. I just bought this last year dont see how that is possible. I guess I'll try to redo BIOS to 5.2 and see what happens.
THOMAS

RAM slot not working

Hey everyone,
I recently bought some RAM for my Mac Book Pro. It came with 1gb, and I bought two 1gb sticks. I put in both sticks of new RAM and my computer would come on but the screen would remain blank. After doing some tests, I found that the lower RAM tray was not working with the old or new RAM stick, and that the upper tray worked with the new and old one. Has this happened to anyone, or anyone have any suggestions on fixes? I tried canned air and it hasn't helped. Currently, I am using the new RAM stick in the upper tray, but would obviously like to take advantage of the lower tray as well.
Thanks!

Sounds like bad news, I'm afraid, Davide. It is likely that the slot itself is damaged. I have seen situations where RAM "reappeared" in the past after an SMC or PRAM reset, but I doubt this is your problem here. Still worth trying, I guess.
Run the Apple Hardware test (on one of the DVDs that originally came with your computer) too, but I suspect it will either need a motherboard repair or replacement.
Rod
(PS - fine surname you have there! )

RAM slots not working (lower)

Hi folks - I had a problem with my PowerBook running very slowly. Helpful friends suggested increasing the RAM. When I set about doing this I found that there were two 256 Mb cards in the machine.
I replaced them both with 1 Gb cards and the Mac was back to a speedy machine. Not long after thanking my friends, I got a 'fatal message' telling me I must restart the machine. When I did this there was no 'sueme' sound and I was back to only 1 Gb of RAM. The lower slot was empty according to the system profiler.
I went to bed dejected!
This morning I removed both 1 Gb cards put back the 256 Mb cards and the machine booted up as usual with 512 Mb of RAM.
So I have put back the 1 Gb cards and have a 2 Gb machine again.
Does anyone know what went wrong? Will it happen again? Do I need to have the machine looked at by a specialist?
Thank you in anticipation
Dunc

There is a known issue with Powerbooks with the lower memory slot failing, and it sounds like yours may be starting to fail. At one point there was an Apple recall for a small sliver of Powerbook systems to fix that.
The alternatives are to run with 1GB in the upper slot, try one of the internet vendors that say they can fix that (check references), or install a used logic board. I don't believe Apple is repairing Powerbooks anymore, so if you want to buy a used logic board, you'll need to install it yourself, or perhaps an Apple Authorized Service Provider would be willing to do the work.

Auto spellcheck not working after a reset

I had to reset firefox and since then my automatic spell check has stopped working. I have been into options and the 'check spelling while typing' is checked. I have rebooted, it is still not working. How do I get it working?

Hi purplequeennl,
Did the attribute change?
In about:config check these settings:
layout.spellcheckDefault
It should be 1.
The Reset Firefox feature can fix many issues by restoring Firefox to its factory default state while saving your essential information. <br>
'''Note''': ''This will cause you to lose any Extensions and some Preferences.''
*Open websites will not be saved in Firefox versions lower than 25.
To Reset Firefox do the following:
#Go to Firefox > Help > Troubleshooting Information.
#Click the "Reset Firefox" button.
#Firefox will close and reset. After Firefox is done, it will show a window with the information that is imported. Click Finish.
#Firefox will open with all factory defaults applied.
Further information can be found in the [[Reset Firefox – easily fix most problems]] article.
Did this fix your problems? Please report back to us!
Thank you.

3gs not working after factory reset

restored factory settings and now have apple logo on screen and phone is doing nothing please help

If you got this after choosing "Erase all content and settings" in the Reset area of the Settings App on the iPhone the fix is DFU Mode Restore.
But first do a Reset, Hold both Home and Power buttons until the iPhone begins to restart. Usually less than 20 seconds.
If nothing, then DFU Mode Restore.
With iTunes open on Computer, connect iPhone, hold both Home and Power buttons for exactly 10 seconds, release Power button, keep holding Home button until iTunes recognizes iPhone in Recovery Mode. This is usually less than 30 seconds more time. If the iPhone screen is now blank, then this is DFU Mode. Restore iPhone Firmware. If you have the Connect to iTunes screen on iPhone this is Recovery Mode, you try the Restore anyway. If it works great, if not try again to get DFU Mode as I described. Even experienced users can have trouble getting DFU Mode, just keep trying you will get it. DFU = Recovery Mode with blank screen.
If this does not work and you have Warranty or AppleCare Coverage take iPhone to Apple for resolution.

Gaming 5 ram slots not working

Hi
I gave just upgraded my mobo and cpu to z97 gaming 5 and i5 4690k. The issue I have is when I use ram slots 3 or 4 the system with not boot and the error code 03 will be displayed. Slot 1 and 2 are working its just when I try and use slots 3 and 4.
As per instruction I should be using slots 2 and 4 but cant.
Any Ideas. Current ram is a data 2 x 2gb

Hi I have tried both individually in each slot, as soon as I use 3 or 4 PC doesn't post. The debug error 03 is displayed on the mobo. No I don't have other ram to try. As I say it works I. 1 and 2 .

RAM Slot Not Working for Macbook 2009 - Looking for Alternatives

Tested RAM slots and found that the second slot (slot closest to interior of computer) is not working properly. Switched both 4gb cards in back slot and the computer would not start up, only would beep....definitely not faulty RAM cards because they both work in the first slot.
I've researched this on forums briefly, the consensus seems to be logic board replacement.
I really don't want to invest more money into this older computer - Macbook Pro mid-2009.
Are there any other troubleshooting options here? I don't think it's the OS and do not have any Time Machine data set up before Mac X nor do I have an partitions set up on an external.
The computer is not terribly slow but when using Final Cut Pro X it tends to lag. All of the specs for my computer fall in the recommendations for using with FC10
Could I get an 8gb RAM card for slot 1?
Any advice would be much appreciated.
Thanks!

Does not look like it supports 16 GBs of RAM meaning only 4 GBs/slot.

Login not working after password reset.

we migrated our ebs system from linux to AIX last week.
previous: 11.5.10.2, 10.2.0.2, linux5.5
present: 11.5.10.2, 10.2.0.2, AIX 6.1
Users are not able to login after they reset their password.
As workaround, we asked them to try the direct forms url: https://host.domain/dev60cgi/if60cgi.exe and they are able to login.
Can anyone help me on this?
Thanks.

Users are not able to login after they reset their password.What is the error they get?
Can you reproduce the issue when you reset the password from the backend (using FND_USER_PKG) or using FNDCPASS?
As workaround, we asked them to try the direct forms url: https://host.domain/dev60cgi/if60cgi.exe and they are able to login.
Can anyone help me on this?Please check Apache log files for details about the error.
Also, please confirm that AutoConfig completes successfully with no errors.
Thanks,
Hussein

Time Capsule Not Working After Hard Reset

A few weeks ago my MacBook Pro started slowing down to a crawl. Eventually ralised it was due to Time Machine not finding the Time Capsule - a known problem.
Reset the Time Capsule (2TB, 8 months old) but although the Internet is working the light is still flashing amber. Carried out a hard reset and still get back to the same situation - the internet is working through the Time Capsule's wireless network but I am getting the flashing amber light.
My internet connection comes into the house and into a wireless modem. An ethernet cable from the back of this modem comes up to my office where the Time Capsule is located into a fast ethernet swtich and then an ethernet cable goes from the switch and is then plugged into the back of the Time Capsule in one of the three internet ports with the <<->> markings.
AirPort Utility shows me that the internet is working and has a green light whereas the Time Capsule has a flashing amber light and 2 errors. When I click the Time Capsule it tells me that the status is:
- Double NAT
- Ethernet Unplugged
Does anybody have any ideas?
TIA

I was having problems with the 7.3.1 firmware as well. For me, in manifest as though the internal disk had went bad--a blinky amber light and a "Disk needs repair" error. Rolling back the firmware solved it for me.
To do this:
--Open AirPort Utility.
--Click on your TC.
--Click on the "Manual Setup" button.
--When the configuration summary pops up, click on the word "Version".
--From the "Upload" drop-down list that is on the new pane that pops up, select "7.3", and click "Ok".
--Once it reboots, it'll be at 7.3.
Hope this helps. I'll be waiting a few weeks after 7.3.2 comes out to upgrade. I'm not real impressed with 7.3.1. As far as I can tell, it broke more than it fixed.

Messages on my MacBook Pro is not working after factory reset, how can I enable it?

I just recently (yesterday) got my MacBook Pro Mid-2012 restored after having a few issues with it. So it is totally "clean."
Today I tried to open Messages which worked previously, but it wouldn't let me send a message to anyone (who I could message before the restore) and if I was able to send a message it would show an "Message Can't Be Sent" symbol next to it. I went to Messages > Preferences > Accounts > and saw that my account was enabled but my email used is in a grey font and it will not let me add my iPhone number.
I have signed in and out, deactivated and reactivated the account and I still cannot message anybody.
Please help guide me into fixing this, I have looked at other boards and it doesn't really help me with my predicament. How can I send a message?
Also in the Messages menu, "My Status" is grey and I can't click anything and as well with the "Log In" option. If this can help developing an idea of what might be wrong.

It won't send it to other emails, but it will for phone numbers. Not sure why, but if you can help with sending to other iMessage emails I would appriciate it :-)

Keyboard Backlight not working after SMC reset

I have a Late 2009 MacBook Pro, and I noticed that the backlight for my keyboard stopped working last night. I Performed an SMC reset and powered the computer back up. Again the backlight never came on, but I noticed that if I pressed the keyboard brightness buttons the icon that used to show on the screen showing what the brightness is at, (like the volume one), was not showing up anymore. I checked the keyboard settings and noticed that the auto brightness for the keyboard dissapeard. Anyone have any suggestions?

try to reinstall your firmware, im having the similar problems, but reinstalling wont let me.... http://support.apple.com/kb/HT1237

17" MBP expresscard slot not working after wake-up

MBP6,1 17" SL 10.6.8
I'm trying to use a bunch of expresscard devices (3 different types of SD card readers as well as two SSDs). All 5 devices are being recognized by OSX and work well as long as the MBP is awake. After closing the lid and open it after a while I always get an error message that the media has been removed improperly. The media (SD card or SSD) is then dismounted and needs to be checked for file system errors.
I have an open incident at German Apple Support (Hotline) for more that 1 year regarding this issue.
IMHO it seems that the expresscard slot doesn't wake up in time before the file system of the SD/SSD media is being accessed and OSX then treats the media as "improperly removed".
I wonder if anyone is suffering from the same issue?
What are my chances of being heard by Apple (at last)?
Could this issue be fixed in Lion or will Lion be identical to Snow Leo (under the hood)?
Best,
Jan

Your notebook is an Enterprise/Business model. I would recommend posting this in the HP Enterprise Support Forums for better coverage.
You can access the enterprise support forums at the following link.
http://h30499.www3.hp.com/
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

1.25 GHz Lower Ram Slot not working

I've got a 15" G4 1.25GHz. When I went to upgrade my RAM (I use Samsung) I noticed my lower slot is dead. I don't know how long it's been that way. I see others who've posted the same issue, and all mention that Apple knows about it and has documentation on it. Can someone point me to that? I've had this thing 3 years and had to replace the battery twice and the power adapter 3 times. Now this...not too impressive.

Your pB is not covered by:
http://docs.info.apple.com/article.html?artnum=303173
Joe

Ram slots not working after CMOS reset

Similar Messages

Maybe you are looking for