Random scorch marks on the screen

Hi all.
I have an early 2009 15 inch MBP and from time to time I get horrible black scorch markes appearing at the base of the screen.
Does anyone have any info on this?

It has happened since new. I have to do a restart to fix it. Does this mean I have a faulty unit that I should have returned when it was under warranty?

Similar Messages

  • I got my screen fix but it got to mark in the screen,

    hello
    i got my screen fix at place for $69 now it got to mark inside the screen what should i do please
    thank kate

    Take the iPod back to where you got the screen replaced.

  • The other day, i was using my iphone 3gs 32gb to take pictures, thenit just shut off, the battery wa around 70-80%. Now it shuts down randomly as long as the screen is unlocked, there will be a chance it will shut off. I have tried draining and charging,

    Hi everyone,
    I was playing games on my 3gs the other day and then it shut off randomly and the screen slowly faded away the battery was at about 70%
    now it will just turn off randomly without warning unless plug into a power source and wont turn on after shutting off unless plugged in
    I have tried restoring it, putting it in a dehumidifier and also charging overnight
    I have tried to drain the battery but it wont work because it will shut down whilst i am draining the battery
    One time today i turned it off and left it for a few hours, the battery was 89% but when i turned it back on a few hours late it showed the plug into power sign
    It charged to about 33% and then a few mins later it went up to 100%
    Could this be a battey percentage sensor problem?
    It anyone has an idea of what might be going on please tell me, it would be greatly apreciated
    Also: i am on ios 5.1.1 and NOT jailbroken
    Thanks
    Kelby

    I had major issues with the iPhone 4s battery, however it’s resolved.
    The tech who set the phone up at the Apple store did so with little training.
    if you have a mobile me account. First go and move all your data to the cloud by going on your computer and logging in at me.com/move. The cloud has replaced mobile me, so there is no need for those two accounts
    Also make sure that for any of your email accounts you set them up to fetch, not push. My tech person set them all to have the email servers push data to the phone. The new iphone4s antenna is extremely strong so it will continually try to access stuff that is pushed–***** a lot of battery life doing this. It makes it worse if you have exchange 2010 accounts. Something about changes made to exchange really suck battery life from devices that access such accounts.
    turning of locator and the push notifications from facebook--they have a lot!

  • How can I remove marks from the screen?

    I inadvertently touched the screen with the tip of a black permanent marker, and now have 2 little black dots spoiling the view! Is there anything I can (safely) use to get rid of them?

    YES there is a solution!
    I had this happen several years back to a new laptop. Someone borrowed my laptop at a business meeting to do a powerpoint presentation and had a permanent sharpie in their hand while they presented. In reaching over to press the "next" button during the presentation, they accidentally wrote on the screen. This put about a 1" blue mark across my screen. I totally freaked out!
    Anyway, in researching a solution, I discovered that there is a chemical solution used to remove permanet marker from photographic negatives without damaging/discoloring the surface or coating. I had a recommendation to try this as it would not damage the laptop screen. It worked great!!! The permanent marker wiped off as if it were a whiteboard. In the years using this laptop, I never noticed the mark again and never noticed any sort of discoloration or damage to the surface or screen coating.
    The chemical is used is a photographic emulsion cleaner called PEC-12. If you do a google search you'll find it all over the Internet. You may also be able to get it (or a reasonable substitute) at a local professional camera shop. You'll also see wipes for sale with these, which I also purchased. It's a lint free cloth that you spray the cleaner on and then wipe the film (or screen).
    I hope this helps you out.
    shepherdboy

  • My iPod Touch has had random lines appearing on the screen at certain times (videos, typing)

    My iPod 5 (32gig) has recently started to do this thing where it will show random lines on the screen when either typing quickly or watching certain videos. They are close to the thickness of your fingernails and occasionally vary in color. I've had this iPod for around a year and a half now and it hasn't suffered any significant trauma. When it happens on the keyboard, the lines only appear on the keyboard. When it happens during a video it only happens where the video is playing (ie. if not on full screen, it only happens on the rectangle where the video is, not the empty space). And it also only happens on certain videos. It happened earlier on a news segment clip on the Fox website, but not on a music video I watched on YouTube three minutes later. For videos, it can be up to three of these lines at once. It first started happening to my keyboard and has since furthered itself to the videos. The screen has two small scratches but other than that it's fine. I'd also like to add even though it may not be relevant that my apps have been crashing more recently as well.
    What do you recommend I do? Why is this happening? Thank you in advance!

    Try:
    - Reset the iOS device. Nothing will be lost      
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings                            
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                               
    iOS: Back up and restore your iOS device with iCloud or iTunes
    - Restore to factory settings/new iOS device.                       
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar                                                              

  • Mac Mini doesn't work:appair only a flashing question mark on the screen

    I try to startup the Mac Mini but the only think that appair on the screen is a white page with in the middle a folder with a flashing question mark.
    The Operative Sistem doesn't work:i wanted to try to inser into the CD of OS X and reinstall all but there is just a CD into the Mac but again with botton or with muose clicked ,the CD doens't go out.
    Please Mac's users help me.
    Bye. Alskarez
    Mac Mini   Mac OS X (10.4)  

    The flashing question mark means that the mini is not able to find a copy of MacOS to boot from, which is likely why you inserted the OS X disc.
    If the disc that is stuck in the system is the original MacOS install disc that came with the mini, you should be able to boot to it by holding the C key down as the system is starting up. Some non-Apple or wireless keyboards don't allow starttup modifier keys to be used, but if yours is an Apple keyboard it certainly should. If it IS the original install disc in the system and the C key doesn't work, and you're left with the flashing question mark, it sounds like you may have a significant hardware fault which may have caused the mini to fail to see either optical or hard drives.
    It may be that in that situation a PMU reset (for PPC minis) or an SMC reset (for Intel models) might restore operability, but if not, then you'll likely need the assistance of an Apple approved service provider.
    To reset the PMU in a G4 mini:
    - Unplug all cables from the computer, including the power cord.
    - Wait 10 seconds.
    - Plug in the power cord while simultaneously pressing and holding the power button on the back of the computer.
    - Let go of the power button.
    - Press the power button once more to start up your Mac mini.
    To reset the SMC on an Intel mini:
    -From the Apple menu, choose Shut Down (or if the computer is not responding, hold the power button until it turns off).
    -Unplug all cables from the computer, including the power cord and any display cables.
    -Wait at least 15 seconds.
    -Plug the power cord back in, making sure the power button is not being pressed at the time.
    -Then reconnect your keyboard and mouse to the computer.
    -Press the power button on the back to start up your computer.

  • Anyone else getting a random "pop" sound when the screen comes on?

    It's random and doesn't seem to affect anything else, but every so often when I raise my wrist to view, a small pop sound emits from the speaker. It doesn't happen every time, and the speaker itself works fine. The only water that has come into contact so far has been from washing my hands.
    Anyone else experiencing this?

    I have this happen too! 42mm Stainless Steel.
    I thought at first it was just the strap or strap connectors clicking when raising my wrist to view the screen, but today I isolated it to the speaker on the device. It doesn't happen every time, but enough that it's a mildly annoying quirk.
    Also, if I take my watch into a very quiet room, hold the speaker slits to my ear, I can hear extremely faint white noise coming from it when the screen is lit. So for some reason when the screen turns on on the Apple Watch, the speaker wakes up too, and when the speaker wakes up, it sometimes emits an clearly audible popping noise.
    Also of note, the speaker functions perfectly fine when on. Notification sounds and calls sound crisp and clear, just for some reason it pops when turning on the circuitry that controls the speaker.
    My device has never touched water.

  • Why does iTunes on my iPhone 5 randomly turn on after the screen lock has been activated?

    On occasion I will grab my iPhone 5 and iTunes will automatically be playing.  The screen was previously locked and iTunes was not initiated before the lock.  It is completely random.

    Hi,
    I recently purchased an iPhone 5 with ATT network.  It worked halfway, and now not at all!  Both companies are pointing the finger at eachother.  I think it is the Apple ios 6.0.1 software upgrade.  I can't even get a tether at all for a few days now.  I've tried every reset, reboot, network settings, restore feature, and finally a new phone.  If they don't get it fixed I'm going over to a S@msung Galaxy III and Verizon. 

  • After reinstalling mountain lion i got the question mark on the screen

    hi everyone,
    after reinstalling mac os x 10.8 from internet recovery, mac restarts itself which is normal.
    but when it starts there is a question mark on a folder symbol on the gray screen.
    what should i do?

    The question mark appears when your computer can't find any bootable volume to start. This can be because of two reasons:
    1. Your computer has forgotten the startup device.
    2. The hard drive is damaged.
    First of all, turn off your computer and turn it on again holding the Option (Alt) key, so you will see all the bootable volumes on the display. Choose the OS X volume and set up OS X as normal. Finally, open System Preferences > Startup Disk, and choose your OS X volume

  • Non Apple mouse pointer randomly jumps all over the screen

    Microsoft mouse is randomly moving on screen. Is this a issue because its microsoft or is there a issue with the Mac?

    The following steps may help to resolve the issue: For Alps touchpad users
    1. Click "Start" and type mouse. Hit Enter key.
    2. In the Mouse Properties windows that comes up, go to "Tapping" tab.
    3. Tick the box labeled "Tap Off When Typing" and click "Ok" For Synaptics touchpad users
    1. Click "Start" and type mouse. Hit Enter key.
    2. In the Mouse Properties windows that comes up, go to "Device Settings" tab.
    3. Click "Synaptics Touchpad" and then, click "Settings". This will open up Synaptics Touchpad Settings window.
    4. Click "Pointing", then "Sensitivity", and then click "PalmCheck" in the left pane.
    5. Now, drag the PalmCheck slider to right to decrease the sensitivity of touchpad.
    6. Click "OK" The following link can be useful:
    https://smallbusiness.chron.com/fix-jumping-cursor-acer-computer-52906.html Hope this will help you.

  • I powered up my macbook and there is a file folder with question mark on the screen flashing.  What does that mean?

    Powered up Mac book and screen showing file folder with question mark flashing? 

    A flashing question mark appears when you start your Mac
    Hope that solves your issue.

  • My iPod just randomly black out like the screen went black but Siri works and you can talk but the screens all black

    I need help

    Try:
    - Reset the iOS device. Nothing will be lost       
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Restore from backup. See:                                                
    iOS: How to back up                                                                                     
    - Restore to factory settings/new iOS device.                     
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
      Apple Retail Store - Genius Bar

  • What does it mean when I see the file with the question mark on my screen?

    What does it mean when I see a file with a question mark on the screen?

    Means no bootable system can be found or required system files are missing or damaged. Reinstall OS X.
    Reinstall OS X without erasing the drive
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install Mac OS X 10.6.8 Update Combo v1.1.

  • When I shut the lid to my computer and then open it again the screen comes on and then goes black and I have to press random keys to make it show again.  Does anyone know why this is happening?

    When I close my lid to make the computer sleep and I open it back up again when I am ready to use it the screen turns on and then turns black.  I have to press random keys to make the screen show again.  Any help is greatly appreciated!

    First, before you sleep your MBP, make sure you either scroll down the Apple menu to sleep your machine, or do it even more easily by pressing CMD-OPTION - DiskDrive (upper right hand corner of your keyboard). I wouldn't just close your machine to let it sleep.
    It's hard to know exactly what's happening, but here are a few pointers.
    1. Go to System Preferences/Energy Saver and make sure you've set a sleep time of more than two or three minutes. Your machine may be trying to sleep too early. In the same preferences, set Computer Sleep to more than ten minutes, to make sure you don't get an unintentional sleep.
    2. Take a look for third-party applications you might have installed.
    Post here with your results!

  • Mark under the iPad screen

    Hey everyone.
    Got my iPad last week, been waiting a while as I live in New Zealand. I'm mostly happy with the product, however the day I got it I noticed a mark under the screen. I have tried to ignore it but I can't. Its only a small mark, whatever it is. When the screen is off it visible from certain angles.
    Any help would be much appreciated
    -Marcus

    Take the iPad to an Apple store or authorized dealer if you can and see what they say... They may not replace it because it may not that big of a defect that would warrant replacement.

Maybe you are looking for

  • HT1386 icloud messes up itunes sync on ipod

    Since using icloud, my ipod no longer appears in itunes as a device. How can I repair this? Certains apps (e.g., Goodreader) don't work without itunes.

  • Two sided printing has stopped working

    Two sided priting has stopped working. Print dialogue box shows two sided as "ticked" but print comes out one sided on two sheets OR "layout" has started to show "long edge binding" as GRAYED OUT. Any ideas please??? 

  • How number words to keep them together on the same line!

    How can I keep words together? As Example: I have words "EN-ISO 2020" now is my text not together. EN-ISO on the end iff the line and 2020 on a new line. It should be alway's together on the next line. Please help this problem!

  • AccessControlException & Reflection ... timeout issue

    Hi all, I have an extremely strange error with my Applet. I have a signed Applet that loads a bunch of GUI components using a custom class loader. That all works fine. In fact, the following works and is tested: - Signed applet tested and works - Cla

  • Instantiation problem

    Hi ! To clarify my problem, I have trimmed down the 4 files (here included) to keep just the essential. When I try to compile the project, I have a �cannot resolve symbol� message for the drawingPanel and the currentObject objects referenced in the T