Raouting, Rate Routing and Cost run Problem

We have changed the our process from routing to rate routing.
But while doing the cost run - CK40N, the sytem is considering the routing in stead of rate routing.
Please advice.
Regards
Pranav

Dear Pranav,
1.Check what selection ID has been assigned in the quantity structure control tab(for the costing variant that is used for costing in
CK40N) for routing selection,If it's 01 means,then check with selection ID 02 where the first priority is assigned for routing type R.
(In standard SAP selection ID 01 by default has first priority to routing - N and then further prirority to rate routing - type - R).So
assuming selection ID 01 is assigned and a product has both routing(task list type - N) and rate routing(task list type - R),now at
the time of costing the system picks up the routing by default as the first priority is set for routing.
2.Also check whether the task list type and the corresponding group and group counter has been changed in the production
version for inhouse manufactured product either in MM02-->MRP4 view or else in C223.
Check and revert back with your further queries.
Regards
Mangalraj.S

Similar Messages

Differences between rate routing and reference rate routings?

Hello PP members:
I would like to differences between rate routing and reference rate routings
Thanks for your time,
Thanks Again,
Suren R

Hi Mr.Suren,
As explained by other friends Routing is used in Discrete manufacturing and Rate routing is used for REM-Repetitive manufacturing.
In addional to these types SAP has given 2 more types
1.Reference operation set -Used in Discrete manufacturing.
2.Reference rate routing - Used in REM.
If similar rate routing is been used for producing many materials,then instead of entering(these steps) in rate routing of each material you create a refrence rate routing and you enter the work centres used and the other details.After saving you get a group counter number showing reference rate routing is saved with group XXXXXXXXX.
When you are creating rate routing for a material say A ,after giving the name and plant details in the top you will be able to see an icon "copy from" and you can select the radio button for reference rate routing and give the group counter number. or else without giving it here you have got an option to select the reference rate routing after entering into the operation screen also.
In that particular page in operation overview screen,there will be an icon copy,there you can click that icon and you can give the reference rate routing group counter number and very easily you can create rate routing for N number of material.
Likewise you can use reference operation set while creating routing for a material in Discrete manufacturing.This basically reduces the time in creating routing or rate routing for materials in Discrete & REM respectively
CA01,CA02,CA03-Create,Change,display (routing) respectively.
CA11,CA12,CA13-Create,Change,Display reference operation set Respectively.
CA21,CA22,CA23-Create,Change,Display rate routing respectively.
CA31,CA32,CA33-create,change,display reference rate routing resp.
I hope this will help you.
If useful reward your points.
Thanks & regards
Karthik.

Exchange rate type in costing run.

Hi all,
In costing run, we use price from customer info record.
Info record is in USD and material is in CAD (Canadian dollar).
During costing run, all the materials are taking exchange rate 'P'. This is correct (as 'P' is maintained in controlling area version)
But for one material alone exchange rate 'M' is being picked up.
Could you please share if you have any idea as to where to check and where the problem could have been.
Thanks in advance.
Regards,
DSK

HI,
Whats the CO-area currency type? I guess for the case you've mentioned there is no currency conversion possible with ex rate type "P", so ex. rate type "M" is taken as a 2nd best option.
To check if converison is possible use SE37, function module "convert_to_local_currency", use the "test" button (F8) and key in the data required for currency conversion (type of rate "P").
Best regards, Christian

Router and Wi Fi Problem

This is more of a question for anyone who is familiar with networking, routers and Wi-Fi...
Here is the problem that I am having...When I am at home and try to watch a YouTube video with the YouTube app the video plays for a little bit then stutters and pauses and buffers...I have a good connection with a strong Wi-Fi Connection at home...
When I took the Playbook to another Wi-Fi network in a totally separate location The YouTube videos run fine...they are quick to load and appear to play no problem...
So my question is...is their a setting in my router that needs to be adjusted to make sure the playbook gets good bandwidth on my home network

What router and firmware version are you running?
I have an issue with my router at home, it is old and I expect it wasnt made for multi connections.
Wii
TV
Blu Ray
2 Laptops
2 desktops
Torch
Bold 9000 (mp3 player and pandora only)
Curve 8520 (pandora only)
Playbook
I can get a BBM and drop connections to most devices at home on my simple router that has latest update.
At the office we have a Netgear WVPN824 and dont experience this at all with over 30+ devices connected.
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

Wirless Router and Bellsouth DSL Problems

Hi,
I purchased the wrt54gx2 router and I have Bellsouth DSL service. I am not very knowledgable about networks and wireless but I purchased this several months ago and I have had several friends take a look and as well as placed calls to Linksys and Bellsouth and can not get this thing to work...its becoming very frustrating. I have a Dell PC with XP that is connected to a Westell modem and can access the internet with no problem however I go through the set up procedure and connect the PC to the WRT54 wich goes to the Westell and No internet through my PC. My hope is to have my PC as a base and use my laptop to roam the house.
My friend that has cable ISP took my WRT54 to his house and pluged it in and was up and running to his laptop in less than 5 minutes.
There is obviously some problem between the modem and router. I have seen talk about PPPoE, Bridge Ethernet, checkin IP address, etc, etc.
Anyone having a similar problem or can anyone please help with some advice??
PLLLeeease!!!

There isn't usually a problem with a Bellsouth DSL... hmmm anyway in your case, how do you log in to the internet through your modem? Do you log in or do you just connect and plug and it goes? Anyway try going to start--control panel---network connections... what items are listed here?

Difference between normal Costing run and Costing run in Material Ledger

Hi everybody,
I have a question i wanted to know why we implement Material Ledger .
If material ledger is for settling variances on material then that is also possible without material ledger
Please clear the doubt what is different in ML as compared to normal costing run
thanks in advance
Regards
Deepa

Costing run is to calculate the std cost estimate of materials and Material Ledger costing run is to calculate Actual cost of production of materials.

Router and Wireless Ps3 Problems. Please help.

well ok i had a previous router, wireless, and it work well with my ps3. Then i found out hey wait, my NAT type 3 is preventing me from playing with my friends. So i tried to fix it. Well something went wrong and my router just completely failed on me. So i went and bought a Linksys WRT160N. Bam it was amazing. My internet work on my ps3 and computer. But yet i still had a NAT type3. The only positive thing was i now had uPnP avaliable. So i went to try and fix my NAT type....then something went wrong again. Today i was opening the ports b/c someone said open your ports to change NAT 3 to NAT 2. Then all of a sudden i try my connection on my ps3 and it says Error 8013013E, cannot reach the access point. It wouldnt even get the Ip Adress. Everything is typed in right and the WPA security, but still cant connect to the access point. Plus if this helps, when i try to do the Wi-Fi Protective Setup, it says failed. I was thinking about just returning the router to its manufactured state but i dont know how. Any suggestions??

I think the ports on your router are not opened properly, that's the reason the NAT type on your PS3 is set to NAT3.
To make your PS3 work with your Router, follow the steps bellow.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter... Leave username blank & in password use admin in lower case...
On the set-up tab change the MTU Size to 1452 and click Save Settings...
Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 80 and End box type in 80, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in DEF, in the start box type in 443 and End box type in 443, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in GHI, in the start box type in 5223 and End box type in 5223, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
4) On the fourth line in Application box type in JKL, in the start box type in 3478 and End box type in 3479, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
5) On the fifth line in Application box type in MNO, in the start box type in 3658 and End box type in 3658, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
6) On the sixth line in Application box type in PQR, in the start box type in 10070 and End box type in 10080, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings
7) Now assign the given ip address on your PlayStation ip address :- 192.168.1.20, subnet mask :- 255.255.255.0, default gateway :- 192.168.1.1...
8) Also assign the dns addresses on the PlayStation Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
9) Turn off your modem, router, and PlayStation...Wait for a minute...
10) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the PlayStation and test it...

Costing run problems

while running costing run, system is showing following error messages.
1. Msg No. 240 Cost component split costed with value of zero
2. Msg No. 168 Cost estimate for material PC-ROH3 / plant is incorrect
Pl. guide
Ranjeetsinh

Hi Maddy
Please check the long tesxt for the error message
60000001
The system found errors in the cost estimate of material component 60000002 from plant 60000003.
60000004
The results of raw material cost estimates that have errors are not used in the product just costed. Only cost estimates that do not have errors or that were released are used in 50000001.
All assemblies that contain material 60000005 from plant 60000006 in their structure are indicated as incorrect.
The message sets the costing status of the 50000002 to 'costed with errors'.
60000007
Eliminate the error at the highest 50000003
thats all
Regards
SK
Rewrd your points

Linksys Router and Screen Sharing Problems

Hello,
I know that problems with Linksys routers and ichat video/screen sharing have been covered here and there in this forum, but I couldn't find a definitive answer.
If I can connect find on a LAN between two Macs, but then get a connection error when attempting screen sharing/video over the internet, what settings should I change on the Linksys?
Thanks in advance.

The Linksys Firewall is normally Off by default.
There are those that try Pinging IP addresses for various reasons.
A Malformed Ping (Ping of Death) can bring down your connection.
To a certain extent this does then become a question of whether you are a big enough target or if someone discovers your IP and tries to do anything about it.
Most will be looking for access to Windows computers so your Mac it that sense will protect itself.
In about 6 years on Broadband with a Constant On Connection none of the modems I have had have reported a a Ping attack and I have had thousands of contacts with people via iChat some of which will have my IP in their Logs.
Significant Decrease ? No
8:24 PM Friday; July 25, 2008

Linksys router and IP address problem

My linksys router is sending out a fake IP address of 24.124... Is there any way to set it so it sends out something else? I'm trying to access a chat server which banned ALL 24.124 addresses because of some hacker doing a number on their server. I really want to get in without having to buy another router. I have a WRT54G V5

If the router is not giving the 192.168.1.x ip, the router might be acting as a pass through already and needs a firmware upgrade. If the firmware upgrade will not save the router, it might be defective.

Problem with cisco series 800 router and SMTP

Hello,
we bought a 877 cisco router and have some problem with SMTP.
I try to read all forum and KB about but do not find any solution.
the problem is that when i try to send any email from client (windows mail) i receive a error 533: you need to supply the correct username and password.
when trying throught hmailserver i receive an email "undeliverable" with this error in body:
Error Type: SMTP
Remote server (62.149.128.202) issued an error.
hMailServer sent: EHLO Globalnet
Remote server replied: 502 unimplemented (#5.5.1)
receving email work correctly.
i'm already using smtp auth, and with my old router everything work fine.
so i beleive is a config problem, maybe with ESMTP (ehlo)?.
i attach my config:

Dear sirs
Thank you for answer so quickly
I download this document from Cisco âConfiguring the (Remote) Common Application Programming Interface for Cisco 800 Series Routerâ.
I have a Lan with Asterisk IP-PBX , the Cisco router have a BRI to public exchange (ISDN) , the router act like a DCP (ISDN- Device Control Protocol) server and listen (DCP messages) in 2578 port.
I need o know the contents of the TCP frame that carry (ISDN-TCP, the DCP messages) to put a SIP client to talk with PSTN/ISDN using the router. I want to write a software module in Asterisk that translate SIP in (ISDN-DCP) to connect the SIP Phones to the PSTN/ISDN using the BRI ports of the Cisco router. I need to now the contents of this message to dialogue with RCAPI server of the router.
If forum is the right place perhaps to put this, Could you give me a better place, a mail or other forum to receive the speciation of (ISDN-DCP)
thank you
With kinds Regards
JoÃ£o Pereira Rosa

WRT54G router and call of duty online gaming

I just bought the WRT54G wireless router and had no problem installing it. I was able to get internet connection on the wired desktop and the wireless laptop. However, when I start playing 'Call of Duty 4' online, within a couple of minutes I start to lose internet connectivity until it completely goes out. At the same time, I will lose connectivity on my laptop as well. In one iteration of fixing this problem, my laptop displayed a message that said something about an 'IP address conflict'.
I called tech support and tried a few different changes in configurations, including changing the MTU to 1400 and creating a static IP address in the 'Accessibility and Gaming' section of the Linksys configurations.
I read several other posts that mention a gaming wireless router (WK300TN or something like that). Do I need that even if I'm gaming on the wired desktop and not on the wireless laptop? Help!

yes WRT310N, WRT330N etc are build for good performance in gaming. Those would definitely improve situation.

Cost estimate/costing run

Hi
What is the difference between cost estimate and costing run?
Thanks,
Nivi

Hello Ram,
There are 3 steps in Costing Procedure. They are
1. Creation of cost estimate
2. Marking of cost estimate
3. Release of cost estimate
Once you release cost estimate, then only system will update the required fields in the database and can be used for transactions.
Hence, cost estimate means, it is just estimated total cost of the product and Costing Run means which inclusive of all the above three steps to complete the total process.
Please let me know if you require any further clarifications.
Thank you,
Regards,
Santosh
Reward points if helpful.

Cost Run should not be getting executed on Material with Price Control V

Raw & Packing materials are with price control V in MM as company wants to keep them on moving average cost. Somehow finance users executed cost run on one such material and cost run was executed and the difference was posted in price difference. As far as I know, system shouldn't be allowing cost run on materials other than those having S as price control.
Question is: How to ensure system sends error if cost run is attempted to be executed on materials with Price Control V?

Hi
If you are executing cost run using CK40N, it releases the cost for all the materials i.e. both for the header and the components
the components may be usually valuated at V. So, the std price update for these will be only for information purposes and it wont revaluate your inventory for sure... This cant post to price difference.... Price diff upon std cost release will apply only to those materials which have price control S
However, if you dont want to release the cost for V items, you can specify them in the exclusion list... In Ck40N selection parameters you specify your plant/material, etc... While specifying the materials to be costed in the multiple selection screen, , you can also specify the ones not to be. Then std cost wont be released in those cases
Regards
Ajay M

Routing Vs rate routing

hi frnds,
whatz the differnce between rate routing and routing...
I knw that rate routing is used for REM.. what are the special fucntion that are avialable in rate routing over the normal routing...
Can we provide a rough production rate in rate routing say 50 qty per hr...
is that possible.....
any inputs... pls help.
regards
csn

Hi Mr.Sarvan,
Routing:
1.A routing determines the sequence of individual operations thar are necessary to produce a Finished product.
2.A Rotuing contains operations & information about work centres at which the individual operations are to be carried out,as well as standard times.
3.It contains the material components required for an operation as well as the nessary tools,jigs & fixtures.
4.Each routing can have one or more alternative sequences & one or more parallel sequences.
5.The planned time for each operation (standard value) is stored in a routing.
CA01,CA02,CA03 - Rotuing creation,change & display T codes.
Rate Routing:
1.One of the Routing type that's used in REM - Repetetive manufacturing.
2.CA21,CA22,CA23-Create,Change,Display rate routing respectively.
Regards
Mangal

Raouting, Rate Routing and Cost run Problem

Similar Messages

Maybe you are looking for