Re: AGREE to select on agreement contract to start to use the App Store. Please can someone tell me where it is, as I am a novice, but even I thought this would be in plain sight! Please can someone tell me where it is so I can use the App Store?
Please help me find where the AGREE is that I need to press so I can start using the App Store ?
You are most welcome
Similar Messages
-
I can't hear anything when making calls no dailing tone or anything but when I try and audioface time it works fine please help
Hi Nfrith1,
Please take a look at the article referenced below, the same as in my original reply. The receiver on the iPhone does not have anything to do with the speakers on the bottom of the phone nor your microphone.
Clear the receiver
The iPhone receiver won't work properly if it's blocked or dirty. Here's where the receiver is:
Follow these steps, testing after each:
Make sure nothing is blocking the receiver, such as a case or film.
If you have a new iPhone, remove the plastic film on the front and back of the device.
Check the receiver opening to see if it's blocked or dirty. If necessary, clean the receiver opening with a clean, small, dry, soft-bristled brush.
While you're on a call, turn on speakerphone. If you still can't hear, then your network or reception could be the issue. Try calling again later or from a different location.
Restart and update
Restart your iPhone and test again.
If there's still no sound or poor sound quality, update to the latest version of iOS.
Get more help
If you've tried these steps and there's still no sound or poor sound quality from your iPhone, contact Apple Support.
Learn what to do if other people can't hear you on a call.
If you can't hear a person on a call or voicemail or if the sound quality is poor on iPhone
Take care,
Alex H. -
How to create NEW Pdf from SELECTED pages?! thought this would be so easy!
I am finding it hard to believe how much time I've sunk into trying to figure this out. I thought it would be as simple as me selecting different pages, right clicking, and then finding "new document from selection," or something like that.
I have a PDF with about 300 pages. I have a list of page numbers that I need in a NEW PDF. What is the easiest way to do this? Thanks so much.
-EricI created a tool that does just that (only you will need to enter the page numbers as text, it does not work by selecting them):
Acrobat -- Extract Non-Sequential Pages: http://try67.blogspot.com/2011/04/acrobat-extract-non-sequential-pages.html -
I thought this would be simple BUT I guess not!
I have two tables Master/Detail. On the detail table I have a database trigger written for insert, update or delete that updates values not the master. This works perfect. Now I add another database trigger that when the master is deleted the trigger deletes the details (ESTBOMHMST_T1). This would work perfect IF the first trigger (UPDATE_ESTBOMHMST_TOTALS ... after insert,update,delete) was not there BUT that one fires because of the delete ... this causes a mutating table error.
I have tried to understand the section in the database triggers help onsite BUT cannot get the combination of triggers working ...
Simply put I want the database trigger to delete my child details when the master header is deleted AND also (via if the UPDATE_ESTBOMHMST_TOTALS) if the detail is acted upon (updated or perhaps just one detail of many deleted) perform a calculation back to the header to update the totals.
Here is the error I and getting and the two triggers currently being used:
ORA-04091: table SDC.ESTBOMHMST is mutating, trigger/function may not see it ORA-06512: at "SDC.UPDATE_ESTBOMHMST_TOTALS", line 5 ORA-04088: error during execution of trigger 'SDC.UPDATE_ESTBOMHMST_TOTALS' ORA-06512: at "SDC.ESTBOMHMST_T1", line 4 ORA-04088: error during execution of trigger 'SDC.ESTBOMHMST_T1'
create or replace trigger "ESTBOMHMST_T1"
BEFORE
delete on "ESTBOMHMST"
for each row
begin
delete from estbomdmst where ref_no = :old.ref_no;
end;
create or replace TRIGGER "UPDATE_ESTBOMHMST_TOTALS"
AFTER INSERT OR UPDATE OR DELETE on ESTBOMDMST
declare
begin
update ESTBOMHMST set total_mat_cost =
(select sum( nvl(mat_price,nvl(mat_cost,0)) * nvl(qty_required,0) )
from ESTBOMDMST
where ESTBOMHMST.ref_no = ESTBOMDMST.ref_no);
update ESTBOMHMST set total_lab_cost =
(select sum(nvl(lab_cost,0)) from ESTBOMDMST
where ESTBOMHMST.ref_no = ESTBOMDMST.ref_no);
end;
Edited by: user2457943 on Jan 15, 2012 7:28 AM
Edited by: user2457943 on Jan 15, 2012 9:27 AMPlease post the details of your DB version.
Your design is flawed for several reasons.
1. The master table is not normalized. It contains rolled up detail information. A design should almost never do this in an OLTP system. Conversely, in an OLAP system the detail data does not change in real-time so there should be no need to perform real-time rollups.
2. You say 'if the detail is acted upon and detail is deleted ' - but the detail trigger code makes NO distinction between INSERT, UPDATE or DELETE operations. Worse the DML for a single detail record attempts to cause the trigger to recalculate the master data for ALL RECORDS and not just the record based on the key value for the detail record that changed. Why are you trying to recalculate summary data for detail records whose data has not changed? That is a design flaw and will never perform anyway.
3. For OLTP systems the rollups of detail data can easily be performed using standard Oracle queries, analytical functions or customized views.
4. For OLAP systems the rollups are typically done as a batch operation after or during the process of updating the master/detail records.
5. Oracle already has functionaliity to delete child records when a parent record is deleted. You create a foreign key constraint on the child that uses the clause ON DELETE CASCADE. When a parent record is deleted the child records will also be deleted. Since there will be no more parent record there will be no child records to roll up. So the entire DELETE portion of both triggers is unnecessary in any case. -
Having problems with air printer to i pad, problem seems to lie with talktalk router, hp solutions managed to get i mac to air printer working but not i pad, adivsed to buy another router as talktalk is not compatiable with bonjour. Went to PC world apple department advised to by airport express. tried setting it up using but will not finalise. i was led to believe this would replace the talktalk router? i feel i have been sold the wrong thing. Any suggestions
This happened to me when I was setting up the wireless router for a friend. The issue is with the Westall modem. You need to go in and setup the "bridge" option on the westell modem. The link below gives directions or you can call bellsouth dsl support (this is how I learned about it).
http://help.bellsouth.net/bellsouth/asp/contentview.asp?isbrowse=true&sprt_cid=3f993409%2Ddff7%2D422...
Good luck
Solution:
Method 1 - Hard Reset
Restore the modem to default settings by pressing the Reset button on the back of the modem and holding it for 3 seconds. (Bridged mode is the default setting for the Westell).
After the modem regains sync, it is in Bridged mode. Do not attempt to surf into the modem as surfing into the modem will enable the Easy Login page and convert the modem from bridged mode to a PPP mode.
Method 2 – Bridged Mode
Access the Westell interface using http://192.168.1.254 or http://launchmodem.
Click on the Broadband DSL Line button.
Click on the Protocols button
Select the radio button to the left of Option 2 (Bridge)
Click the save button. Once the modem has restarted it is in bridge mode.
ALL STEPS COMPLETE -
I am trying to update the apps in my computer, but even though I am signed in with my Apple ID in the App Store, the tab where I am supposed to enter my Apple ID to to update it, someone else's email apprear. What do I do?
You installed a hacked app, originally from the Mac App Store. It contains the receipt for a different app, downloaded using an account that you don't control. You need to identify and remove the hacked app.
Important: The app you need to remove is not necessarily the one named in the App Store alert. For example, the App Store may prompt you to update "Angry Birds" or "Twitter," but the hacked app may be something else entirely. Don't make any assumptions about which app you're looking for. To find it, you must carry out a systematic search with Spotlight.
1. Triple-click anywhere in the line of text below on this page to select it:
kMDItemAppStoreHasReceipt=1
Copy the selected text to the Clipboard by pressing the key combination command-C.
2. In the Finder, press command-F to open a search window, or select
File ▹ Find
from the menu bar. In the search window, select
Search: This Mac
from the row of tokens below the toolbar. Below that is a popup menu of search criteria, initially showing Kind. From that menu, select
Other...
A sheet will drop down. In that sheet, select
Raw Query
as the criterion, then click OK or press return.
Now there will be a text box to the right of the menu of search criteria. That's where you enter the raw search query. Click in that box and paste the text you copied earlier by pressing command-V.
4. The search window will now show all the App Store products that are installed. Compare those search results with the list of your purchases from the App Store. To see the complete list, you may need to unhide hidden purchases. If any apps were download from the App Store using other Apple ID accounts that you control, sign in to the store under each of those ID's and check the purchases.
At least one of the apps in the Spotlight search results is not among your purchases in the App Store. Move each such item to the Trash, after quitting it if it's running. You may be prompted for your administrator password. Empty the Trash.
Quit and relaunch the App Store. Test.
If you find these instructions confusing, ask for an alternative method. -
How do I get music already on my laptop into my itunes account library? I have just done the icloud match thinking this would pick them all up, but it hasn't, all it has done is match the 40 songs I already have in my itunes library. I wanted to get some more music onto my iphone and I am stuck. If someone could assist, that would be great. Thanks. Sue
Suzybabe wrote:
Fantastic, how easy this was, searched and searched through itunes help and forums earlier today and this little gem of instruction is nowhere to be found.
Many thanks ed2345.
Sue
Sue,
Glad to hear that it was helpful. Enjoy the music!
Ed -
How can a company sell a Times Capsule appliance as a solution for backup and die for this manufacturing fault? And with that Apple? nothing, or technical assistance in Brasil. Of a sledgehammer, open the device and attempt to recover your files by force!???
Heat up the bottom rubber mat with a hairdryer for 5-10 minutes to loosen the adhesive, then pull the rubber mat away from the bottom metal plate carefully.
Then use a screwdriver to remove the 10-12 screws to open up the case. -
I have dozens of legacy BB 8310 curves that I'm trying to configure for staff. Email has been set up fine but I can't for the life of me figure out how to sync contacts from gmail.
I know Google Sync is no longer available, but we don't use Outlook so I have no idea how to have my staff sync all their contacts from Gmail accounts.
Please anyone give me some help here...have researched for hours and I can't figure it out.
I'm running software version 4.5.0.55 and I haven't found any more recent software versions approved for the 8310.Hi and Welcome to the Community!
Here is a KB that discusses that function:
KB19269 What is Google Mail contact synchronization
As you can see, the device software version you are using is too old for this function.
As far as I can tell, OS development for the 8310 may have stopped in the 4.x range...but it's hard to know for certain. You can dig, carrier by carrier, through the official download portal to find carriers that still support the 8310 and that will reveal to you the exact OS's that are available for it:
http://us.blackberry.com/support/apps-and-software/desktop-and-device-download-sites.html
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
I think there should be a flash card app that let's u put in ur own info. I'm studying for a test and I think it would be really cool to have my flash cards in my phone!! Is there an app like that already?
http://www.appshopper.com/education/flashcards
-
Hello, I just bought a Airport Express, and on the first day it has a a weak signal. It is very far from my working space and my apartment has very thick walls that might be blocking the signal. I would like to know if I can do anything to make it stronger or faster. If you know please reply.
You need to move the AirPort Express closer to the bedroom.
You can leave the modem at its current location and purchase a longer Ethernet cable to move the AirPort Express virtually anywhere that you want. The closer that you can locate the AirPort Express to your working space, the better the signal will be.
Standard lengths of Ethernet cables are 6 feet (2 meters), 25 feet (8 meters), and 50 feet (15 meters). Any computer / electronics superstore will have a selection of Ethernet cable from which to choose. -
Hi all,
The previous query is absolutely ok.
The only thing i want to change is ...
get all the previous available ve1 AND NEW: if a AGNR has no ve1-instance, regardless get an ve1-instance with the agnr filled but f.e. the other fields empty
The grouping could made in reporting-logic later, and not in the tsql-query.
resultset i need:
- all agnr, if the have an ve1-instance or not
Groups (hierarchy) i need, later in Report:
- AGNR
- ve1 (with all the left joind fields pg, vnfk, vnpk, vm (if they are)
- if a agnr has no instance of ve1 --> print: "NO ver available"
SELECT
ve1.new_verid,
ve1.new_no,
ve1.statuscode,
ve1.statuscodename,
ve1.createdon,
ve1.createdby,
ve1.createdbyname,
ve1.new_begin,
DATEPART(yyyy, ve1.new_begin) AS begin_year,
ve1.new_end,
ve1.new_vn_fid,
ve1.new_vn_fidname,
ve1.new_vn_kid,
ve1.new_vn_kidname,
vnpk.new_how_old,
ve1.new_vg,
ve1.new_vgname,
ve1.new_vs,
ve1.new_vsname,
ve1.new_vstat,
ve1.new_vstatname,
ve1.new_zw,
ve1.new_zwname,
ve1.new_bn_zw,
ve1.new_rlz_v,
ve1.new_pgid,
ve1.new_pgidname,
pg.accountnumber as pg_accountno,
ve1.new_agnr_agnr_avmid,
ve1.new_agnr_agnr_avmidname,
AGNR.new_vm_kid AS vm_contactid,
AGNR.new_vm_kidname AS vm_contactidname,
ve1.new_efv,
ve1.new_efvname,
CASE
WHEN ve1.new_vn_kid IS NOT NULL THEN 'Private Customer'
WHEN ve1.new_vn_fid IS NOT NULL THEN 'Account Customer'
ELSE 'Kunde'
END AS kunde_typ,
DATEPART(yyyy, vnpk.birthdate) as vnpk_birth_year,
CASE
WHEN ((ve1.new_rlz_v IS NOT NULL) OR (ve1.new_rlz_v > 0))
THEN ve1.new_rlz_v
WHEN (DATEPART(yyyy, ve1.new_begin) IS NOT NULL) AND (DATEPART(yyyy, vnpk.birthdate) IS NOT NULL)
THEN 65 - ((DATEPART(yyyy, ve1.new_begin)) - (DATEPART(yyyy, vnpk.birthdate)))
ELSE 20
END AS vlz_calc,
CASE
WHEN ((ve1.new_bnj IS NOT NULL) OR (ve1.new_bnj > 0)) THEN ve1.new_bnj
WHEN ((ve1.new_bn_zw IS NOT NULL) OR (ve1.new_bn_zw > 0))
THEN
CASE
WHEN new_zw = '100000008' THEN ve1.new_bn_zw * 12
WHEN new_zw = '100000004' THEN ve1.new_bn_zw * 4
WHEN new_zw = '100000002' THEN ve1.new_bn_zw * 2
WHEN new_zw = '100000001' THEN ve1.new_bn_zw * 1
WHEN new_zw = '100000006' THEN ve1.new_bn_zw
ELSE 0
END
ELSE 0
END AS bnj_calc
FROM
Filterednew_ver AS ve1
LEFT OUTER JOIN Filterednew_agnr AS AGNR
ON ve1.new_agnr_agnr_avmid = AGNR.new_agnrid
LEFT OUTER JOIN FilteredAccount AS pg
ON ve1.new_pgid = pg.accountid
LEFT OUTER JOIN FilteredAccount AS vnfk
ON ve1.new_vn_fid = vnfk.accountid
LEFT OUTER JOIN FilteredContact AS vnpk
ON ve1.new_vn_kid = vnpk.contactid
LEFT OUTER JOIN FilteredContact AS vm
ON AGNR.new_vm_kid = vm.contactid
WHERE
(ve1.createdon >= @Begin_Week)
AND (ve1.createdon <= @End_Week)
AND (ve1.new_vg = @vg)
AND (ve1.statuscode = '1')
AND (ve1.new_efv <> '100000000' OR ve1.new_efv IS NULL)
AND (ve1.new_vstat <> '100000004' OR ve1.new_vstat IS NULL)
AND (ve1.new_zw IN ('100000008','100000004','100000002','100000001','100000006'))
ORDER BY
ve1.createdon
i thought, and tried with right joins, but i think i need to change the sight (the complete query)?
thx for all kind of help
Greets PebHi Peb,
Please provide sample data and expected results. -
I thought this was wireless?? Help please..
As I'm holding for tech support, I thought that perhaps someone here could help me. I just purchased my Linksys Wireless-G Broadband Router, Model WRT54GS. From what I understood the router would completely eliminate wires with the exception of the ethernet cable going from the modem to the router. The instructions are stating that I will have a cable going from the modem to the router and one going from the router to my computer? If so, that completely defeats the purpose of me purchasing a WIRELESS router, and I will be returning it promptly. Is this true? Please help...
Once you configure your router, you remove the cable.
Greetings from Northern Ontario, Canada -
I get this report everytime i try to open firefox:
AdapterDeviceID: 9490
AdapterVendorID: 1002
Add-ons: {5F590AA2-1221-4113-A6F4-A4BB62414FAC}:0.45.6.20100202.1,{89506680-e3f4-484c-a2c0-ed711d481eda}:0.9.5.6,[email protected]:1.1.1,{6F0976E6-26F3-4AFE-BBEC-9E99E27E4DF3}:1.4.14,{a0d7ccb3-214d-498b-b4aa-0e8fda9a7bf7}:20110323,wikilook@testpilot:2.7.0,[email protected]:4.0.20110415,{EF522540-89F5-46b9-B6FE-1829E2B572C6}:5.0.3,{b9db16a4-6edc-47ec-a1f4-b86292ed211d}:4.9.3,{46551EC9-40F0-4e47-8E18-8E5CF550CFB8}:1.2,{CAFEEFAC-0016-0000-0022-ABCDEFFEDCBA}:6.0.22,{CAFEEFAC-0016-0000-0023-ABCDEFFEDCBA}:6.0.23,{CAFEEFAC-0016-0000-0024-ABCDEFFEDCBA}:6.0.24,{d10d0bf8-f5b5-c8b4-a8b2-2b9879e08c5d}:1.3.9,{CAFEEFAC-0016-0000-0026-ABCDEFFEDCBA}:6.0.26,{cc85cd4e-5a5b-4eda-a25c-bdaffa93b406}:0.7,{972ce4c6-7e08-4474-a285-3208198ce6fd}:5.0
AvailableVirtualMemory: 4115996672
BuildID: 20110615151330
CrashTime: 1309981062
EMCheckCompatibility: true
FramePoisonBase: 00000000f0de0000
FramePoisonSize: 65536
InstallTime: 1308935344
Notes: AdapterVendorID: 1002, AdapterDeviceID: 9490, AdapterDriverVersion: 8.632.1.2000
ProductName: Firefox
ReleaseChannel: release
SecondsSinceLastCrash: 636
StartupTime: 1309981057
SystemMemoryUsePercentage: 63
Theme: classic/1.0
Throttleable: 1
TotalVirtualMemory: 4294836224
URL:
Vendor: Mozilla
Version: 5.0
Winsock_LSP: Tcpip MSAFD [TCP/IP] : 2 : 1 :
Tcpip MSAFD [UDP/IP] : 2 : 2 : %SystemRoot%\system32\mswsock.dll
Tcpip MSAFD [RAW/IP] : 2 : 3 :
MSAFD Tcpip [TCP/IPv6] : 2 : 1 : %SystemRoot%\system32\mswsock.dll
MSAFD Tcpip [UDP/IPv6] : 2 : 2 :
MSAFD Tcpip [RAW/IPv6] : 2 : 3 : %SystemRoot%\system32\mswsock.dll
Provedor de Serviço de TCPv6 de RSVP : 2 : 1 :
Provedor de Serviço de TCP de RSVP : 2 : 1 : %SystemRoot%\system32\mswsock.dll
Provedor de Serviço de UDPv6 de RSVP : 2 : 2 :
Provedor de Serviço de UDP de RSVP : 2 : 2 : %SystemRoot%\system32\mswsock.dll
MSAFD RfComm [Bluetooth] : 2 : 1 :Can you start Firefox in [[Safe mode]] ?
You can also do a clean reinstall and download a fresh Firefox copy from http://www.mozilla.com/firefox/all.html and save the file to the desktop.
Uninstall your current Firefox version and remove the Firefox program folder before installing that copy of the Firefox installer.
It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
You can initially skip the step to create a new profile, that may not necessary for this issue.
See http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Clean_reinstall -
I keep losing notes once I've added them. I don't know how to confirm where they are being stored. I'm wondering if the storage could be full. Also tried to sync with my yahoo account thinking that might help. But not sure how I get existing notes to sync with the account....they didn't show up once I turned that feature on.
were using icloud?
you can check to see if there by logging into your account at icloud.com
Maybe you are looking for
-
How Can I Control Format & Color Of Text Links?
iWeb appears to colorize and/or box or underline link text according to its own "uncontrollable" set of criteria. How can I control the color of a text hyperlink and turn automatic link underlining OFF?
-
Data not populated when run from a different machine
I have a stored procedure which populates a table The stored procedure when it is run on my machine using SQL Plus populates data correctly in a table. I select using SQL PLUS and it shows that the data is there But when I run the SAME procedure ( SA
-
After I download a 256 kbps song from the cloud using ITunes Match, how do I get it to play on my computer once I turn ITunes Match off again? I have been using ITunes Match for awhile now to increase the bit rate on songs to 256 kbps. Once I downlo
-
Hello, This is my first time usinf a help forum and this is my first attempt to convert old vhs home movies to the digital realm. This step is slow and tedious but successful. I have completed DVD copies of vhs tapes but am unable to utilize them in
-
[Desktop] Every grid view should have an option for a vertical listing
For example the Artists screen under Your Music, and albums displayed on an artist page. Grid views are kind of pretty if you like colours. They're pretty awful for finding a particular thing by name. For example if I am looking for Infected Mushroom