Re: applock and smart app lock does not work on 5.1.1

Hi @omdavice @wantboost When turn on the sony only the red led light flashed multiple times. This could be because battery was fully drained or there
was a problem with the boot. If you press the 3 buttons Power, Volume down and Volume up for about 8 seconds and then release them, the sony logo would appear. If this doesn´t work, you can also first run a backup of the device information like this: http://talk.sonymobile.com/t5/FAQ/Backup-amp-Transfer/m-p/407253#U407253 Then try performing a system repair using PC Companion: http://support.sonymobile.com/gb/tools/pc-companion/ This will factory reset your phone and erase all data. You might need tocharge your device for about 1-2 hours before so the device has at least 80% battery. Make sure the device is not connected to computer or laptop and turned off (sometimes you have to press power button and volume up until the device vibrates 3 times or on some devices you have to press the small button near the SIM tray or on the back of the device). Start PC Companion and select Support zone then Update my phone/tablet then in Blue Repair my phone/tablet and follow the on screen instructions - When prompted connect your phone still switched off holding volume down or back button - This should start the repair or reformat process. If you are using Windows 8/8.1 or a 64bit operating system then adjust the settings for PC Companion and run in compatibility mode and chose Windows 7 or XP. I hope can be useful.
Best Regards,

My Xperia ZL have an strange battery behaviour. It started with a crazy battery indicator, for example, sometimes it is showing 75% of battery, then I start to use some app, and the battery drains to 50%, but right after I close de app, the battery shows 63%. So I've never been able to know how my battery is going for sure. Sometimes it is showing 35%, then I just use some app for a few minutes, the battery goes to 15% and suddenly the phone turns off. But when I reboot it, it is showing 30% again.
To charge the phone's battery, I must have luck, because it looks like the phone choose when it would like to charge the battery. The problem turns worst when the battery drains totally. The battery simply doesn't charge, the phone turns on and off constantly. When I plug the battery charger, the LED indicator glows a weak red light, then the "SONY XPERIA" appears, and then the phone turns off, the cycle repeats if I let the battery charger plugged in, back to the weak red light.
Does anyone here had the same problem with Xperia ZL? Does a simple battery change might resolve this issue?
Thank you!  

Similar Messages

  • I generated a new Itunes Account and now the App sync. does not work with theapps I bought with the old account. Is it possible to merge the old and the new account ?

    I generated a new Itunes Account and now the App sync. does not work with the apps I bought with the old account. Is it possible to merge the old and the new account ?

    It is not possible to merge Apple IDs. 
    Why did you create a new one?

  • I updated to 6.1.3 on my iPaad 1, and now my app store does not work.  What should I do?

    I updated to 6.1.3 on my iPad 1, and now my app store does not work.  What should I do?

    The Complete Guide to Using the iTunes Store
    http://www.ilounge.com/index.php/articles/comments/the-complete-guide-to-using-t he-itunes-store/
    Can't connect to the iTunes Store
    http://support.apple.com/kb/TS1368
    iTunes: Advanced iTunes Store troubleshooting
    http://support.apple.com/kb/TS3297
    Best Fixes for ‘Cannot Connect to iTunes Store’ Errors
    http://ipadinsight.com/ipad-tips-tricks/best-fixes-for-cannot-connect-to-itunes- store-errors/
    Try this first - Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
    This works for some users. Not sure why.
    Go to Settings>General>Date and Time> Set Automatically>Off. Set the date ahead by about a year.Then see if you can connect to the store.
     Cheers, Tom

  • My auto-lock does not work properly in this new iOS 6

    My auto-lock does not work properly in this new iOS 6

    Do you have your Assistive Touch on? Per another user in another forum:
    Source: http://forums.imore.com/ios-6-forum/240631-auto-lock-not-working-ios-6-a.html. Username: Chambaka
    Okay, I did a 'reset all settings' in settings and problems fixed. Hope this can be useful for others.
    Edit: it appears that when the assistive touch is on the autolock function won't work while in the home screen, but will work if opening a app. I hope Apple fixes this bug in the next update.
    I tried what he said and my auto-lock's working again - so, I turned off my Assistive Touch. Hope Apple fixes this bug soon,

  • My Pokerist app sound does not work, only with headphones....can anyone help me? Thank you

    My Pokerist app sound does not work.  It will only work if I have head phones on.  All other sound works, songs, video etc.  I deleted the app, then installed again still no sound.  It is not the app because I also have a IPhone and the sound works on Pokerist.  If anyone can help me I would appreciate it.
    Thank you
    Smartypants0

    Check out this link - http://support.apple.com/kb/HT4085.  There have been instances where settings have accidentally changed. Double click on the Home button, swipe all the way to the right to reveal the leftmost icon and alternate settings if necessary.

  • HT204135 I update my Mac to version 10.9.2 and now my printer does not work anymore. I did all the software updates and I do not understand why my mac does not recognize the printer anymore?

    I update my Mac to version 10.9.2 and now my printer does not work anymore. I did all the software updates and I do not understand why my mac does not recognize the printer anymore?

    Go to the website of the manufacturer of your printer and check to see if they have released an updated driver for your particular model.

  • How do I fix my iPod I updated it to iOS 6 and now iTunes and the App Store will not work?, How do I fix my iPod I updated it to iOS 6 and now iTunes and the App Store will not work?

    How do I fix my iPod I updated it to iOS 6 and now iTunes and the App Store will not work?, How do I fix my iPod I updated it to iOS 6 and now iTunes and the App Store will not work?

    App Store Failure / Updates White Screen
    Tap Settings > General > Date and Time > Set Automatically > Off. Set the date one year ahead. Then try to access the App Store.
    It may be a connection issue. Try changing your DNS settings to Google’s open DNS by tapping Settings > Wi-Fi >, tap the blue arrow next to your current Wi-Fi network, and then tap the “DNS” field and enter the DNS servers; 8.8.8.8 (Google’s Public DNS, 8.8.4.4 also alternate).

  • Why does Adobe sendnow work and the newest and greatest Adobe Send does not work?

    Why does Adobe sendnow work and the newest and greatest Adobe Send does not work? I wasted about 8 hours on trying to get Adobe Send to upload 269 files that amounted to 469MB. When it did not work I made a zip file and after a lot of wasted run time that did not work. The first situation gives little indication of when a file is loaded compared to Adobe SendNow. In both cases with Send it failed with a message like only the first 50 can be loaded. When I went and looked none of them had been loaded. With the zip file (I wanted to hide the individual files so they would not be counted) it appeared to work but very slowly and finally said it was done and I went and looked and it had done anything for oever 2 hours except a false "I'm runninng" indication.
    Thus, I took a chance with Adobe SendNow and it works great. It never gave me a limit on the amount of files nor on the size of the complete job. It shows me one file at a time when it has finished with the file uploading it. SendNow has never given me any problems.
    Why woiuld you want to change the program from SendNow to Send without the newest program being the best, fastest, user friendly program of the two? It just doesn't make sense to me. I suggest that Adobe keep SendNow working until Send is fixed. I would also suggest that SendNow and how it looks be kept, called Send, then modify Send one thing at a time until you get it to the point you need it to be for Acrobat. I have heard nothing good and now I have experienced it that Send is a piece of junk. I wasted most of my work day on giving Adobe the benefit of the doubt to find out I made a very bad decision to trust Adobe to make good decisions on the transfer of a function to another place .... both Adobe's responsibility.without making it painless for your customers that totally rely on you. Don't throw away customer confidence as it is very hard to get it back.

    Funny how you answer to "troll". (What's your handle on AT&T forums?)
    Yep! Verizon living up to it's contractual obligations by not releasing updates. Caveat emptor!
    I think there are some reasonable expectations here to keep customer's happy. When one carrier offers upgrades there is an expectation the same will happen across all the carriers. We have seen that except Big Red.
    Verizon could have said the update is in MS court months ago and stilled the voice of the disgruntled, or at least redirected it, but instead chose to be silent. Not for market share but for partial blame I think.
    We will have to agree to disagree since you only see Terms & Conditions and I, see customer satisfaction.

  • TS3212 I get an apple application support error when installing itunes. It says uninstall and re-install.  Does not work.  same message.  What is a solution?

    I get an apple application support error when installing itunes. It says uninstall and re-install.  Does not work.  same message.  What is a solution?

    Is that an error 2 message?
    If so, let's try a standalone Apple Application Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of the issue.
    Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
    http://www.apple.com/itunes/download/
    Download and install the free trial version of WinRAR:
    http://www.rarlab.com/
    Right-click the iTunesSetup.exe (or iTunes64Setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
    Go into the folder and doubleclick the AppleApplicationSupport.msi to do a standalone AAS install.
    Does it install properly for you?
    If instead you get an error message during the install, let us know what it says. (Precise text, please.)

  • Hello everybody,i've forgot my apple password and i wanted to reset it to a new one but i also forgot the security question and the alternative email does not work and i am really need to log in to my apple i d because my iPhone 4g won't  let me access it

    Hello everybody,i've forgot my apple password and i wanted to reset it to a new one but i also forgot the security question and the alternative email does not work and i am really need to log in to my apple i d because my iPhone 4g won't  let me access it so anyone can help me with it or can i put another apple id to it without putting the first password?THANKS FOR YOUR HELP.

    Then call AppleCare and talk to someone in account security.

  • My serial number for adobe photoshop elements 12 and premiere elements 12 does not work

    My serial number for adobe photoshop elements 12 and premiere elements 12 does not work.  On adobe.com it shows that the serial number I received is associated with adobe photoshop elements 9 and premiere elements 9.  I have purchased those products in the past, but just recently upgraded to elements 12.  I can use the the photoshop organizer, but can't open the photoshop editor.

    You need to contact Adobe Support either by chat or via phone when you have serial number and activation issues.
    Here is a link to a page with options to help make contact:
    http://www.adobe.com/support/download-install/supportinfo/

  • Since upgrade to v29, pinned tabs don't appear and sometimes all tabs don't appear and open menu button does not work

    My pinned tabs don't appear at any start and at some starts, I don't see the bookmarks toolbar (I can restore that by removing it from view-toolbars and then reselecting it). when this happens, FF also does not show any tabs and the Menu button does not work.
    I have tried various suggestions found on here like deleting the sessionstore.js and re-installing FF, also tried disabling hardware acceleration in safe mode and still have the same problems.
    Am reluctant to reset FF in case I lose my favourites and Bookmarks, is there anything else I can try?

    Firefox may not have closed properly.<br />
    You can try to update to Firefox 29.0.1 to be released tomorrow (Friday) to see if that helps with this issue.
    See also:
    *"Hang at exit": http://kb.mozillazine.org/Firefox_hangs
    *"Firefox hangs when you quit it": https://support.mozilla.org/kb/Firefox+hangs

  • HT201412 my wifi button does not working / it looks grey and can not open it... and my some applications does not working too ... please help me ... I bought this I phone from Beirut/Lebanon and i live in Turkey...

    my wifi button does not working / it looks grey and can not open it... and my some applications does not working too ... please help me ... I bought this I phone from Beirut/Lebanon and i live in Turkey...

    Here you go:
    http://support.apple.com/kb/ts1559

  • When I open firefox before connecting (via 56k modem) or if I leave a previous section open, disconnect and then reconnect, firfox does not work, it remains offline, even though internet is connected. I have to close firefox and reopen

    When I open firefox before connecting (via 56k modem) or if I leave a previous section open, disconnect and then reconnect, firfox does not work, it remains offline, even though internet is connected. I have to close firefox and reopen

    Thanks for the reply. I never get the option to "Restore Previous History" from History. I don't even have the box checked that asks to delete the history when Firefox closes. I don't know what's wrong, no matter what, I always lose everything. I have the box marked "Show my windows and tabs from last time" for when I open Firefox, but it never shows that, just my homepage. Also, when I check my History, it only shows the pages that I opened since I started Firefox, nothing from before. Even if I were to open up 10 pages now, close Firefox, and open it, the history would only show the homepage that opened this time, not any of the 10 pages that I opened 5 minutes ago.

  • I have updated my iPhone 6 to iOS to 8.3 and the Blutooth still does not work

    I Have updated mu iphone 6 to iOS 8.3 and the Blutooth still does not work in my car for hands free

    Why would you expect it to work in 8.3, if it didn't work in a previous version? What troubleshooting have you done? Have you tried putting the car system into Pairing mode?

Maybe you are looking for

  • Cannot copy and paste in InDesign CS6

    I am trying out InDesign CS6 as an upgrade, but I cannot copy and paste. Does anyone know about this or have a solution? Thanks, Maya

  • Query optimization

    I'd like to bring to everyone's attention a very unusual scenario involving a query with CTE, multiple union all, and unpivot, over unnormalized data used by a transactional application. Because the data structures are sensitive, I've created separat

  • Copy and Paste in an Application (like sql-workshop)

    Hey, i would like to implement a functionality to copy & paste (similar to sql workshop) data from an excell sheet into a formular. by submitting this formular i want to create a set of data after the 'tab' dividing. its not comma seperated. because

  • AX set up as WDS to use with a switch.  does airtunes capability go away?

    quick question, since i can't seem to find the answer to this. if i configure an ax as wds (so i can use the ethernet port to hook to a switch), will it still work as an airtunes distribution point? i suppose i could try it... but taking the lazy way

  • Script Editor with Adobe Interactive Forms

    Hi Everybody, I have an issue (i think!) with the Adobe Interactive Form Editor in my NWDS. I need to use some scripts in my PDF form, and i though that the script editor will be helpful, but this is disabled. Somebody knows how to enable it? If I ha