Re: Equium A60-672 will not log on - winlogon.exe - Ordinal not found

Hi, got a Equium with a problem booting up into Windows XP Home. It goes through the main screen then shows the above and the message " The orinal 258 could not be located in the dynamic link libary SHELL32.LL.
When I press OK it comes up with a user interface failure message saying "the logon user interface DLL msgina.dll failed to load" Then all I can do is restart it and it starts with the messages again.
I dont have an recovery or install disk.
Can anyone help?

All drivers, tools and utilities for your notebook model you can find on Toshiba support page under http://eu.computers.toshiba-europe.com > Support & Downloads.

Similar Messages

Equium L10 -200 - Will not switch on

HI,
My laptop will not power up, it will not switch on at all.
I charged it for over 12 hours, but still it would not power up.
The light that indicates that a charger is plugged in doesn't even come on.
The charger is fine, as I was able to charge an older laptop wih it.
Any help would be appreciated, many thanks.
hk

If removing the battery doesnt fix the problem, then there is no easy way of fixing it. The mainboard needs replacing.
ASP = Authorized Service Center

Equium A60: DVD-RAM not being recognised properly

Hiya!
I have a EA60 and my Mat****a DVD-RAM UJ-820S is being not being recognised by the Notebook properly. When I go into Device Drivers it says the driver has loaded but comes up error code 41. I've reloaded the Driver and the Device and this makes no difference.
I also bought a new Pioneer DVD-RAM and this comes up with the same error code.
Anyone out there can help me please?
[email protected]
Regards,
Gary

You could try this method, maybe it works:
Start Registry Editor
Locate the UpperFilters value under the following key in the registry:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}
On the Edit menu, click Delete, and then click OK.
Locate the LowerFilters value under the same key in the registry:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}
On the Edit menu, click Delete, and then click OK.
Quit Registry Editor and restart your system. Now windows should recognize your ODD correctly.

Equium A60: I get error message using explorer.exe

Everytime I try to open an image file using Paint or Fax/Image viewer, or I try to drag a file into a folder I get the following error message:
"Windows Explorer has encountered a problem and needs to close. We are sorry for the inconvenience"
The error report says:
"AppName: explorer.exe AppVer: 6.0.2900.2180 ModName: rpcrt4.dll
ModVer: 5.1.2600.2180 Offset: 000847a6"
Also I cannot open webpages that open in new IE windows. Norton Internet Security 2005 also would not open, but did claim to be active in the background.
Does anyone have any advice for me?
I've tried all the help for explorer.exe problems on helpwithwindows.com but nothing they suggested worked - such as spyware, malaware removal. I've run a few online virus checks - since Norton won't work I had to try the online scans.
The laptop was bought last year, and we've lost the recovery CDs - so if we need them, then where can we get replacements?
Many thanks,
Jonathan

Hi
Well, this sound like a OS software malfunction. It's possible that some registry entries or/and data files are corrupted and damage.
However, the best solution is to recover the OS.
The other possibility is to use the "system restore" tool of Win XP.
Then you can try to roll back the OS to the early point. But if it doesnt work so the new installation is needed.
regards

Equium A60-157 Wireless Network Card/PCMCIA HELP!

Hi, all!
This problem has been frustrating me for at least 2 months.
Ok, I recently purchased a Belkin Wireless G Notebook Card (wifi card).
The first time I installed the wifi card it was working perfectly. I powered
off the laptop (after I had finished working on it). The following day
when I powered on the laptop, you guessed it, the wifi card was not
working. I did not remove the wifi card during the power off/on phase.
When I went into the device manager, a yellow exclamation mark was
above the wifi card. When I examined the wifi cards properties, I found the
following message:
This device cannot find enough free resources that it can use. (Code 12)
If you want to use this device, you will need to disable one of the other devices on this system.
Click Troubleshoot to start the troubleshooter for this device.
I have tried unistalling and reinstalling the wifi card. I have tried using the latest Belkin drivers for the wifi card. Sometimes it works, but when I power off/on the laptop its a no go.
One way I have gotten the card to work was by removing and inserting the card several times
until it found resources and finally worked. I dont use this method anymore as, quite obviously, I risk causing damage to the cardbus slot and the card. In the meantime Ive been using a Belkin Wireless G USB network adaptor. I have not had any problems with the USB adaptor, but I would prefer to use the wifi card. This is because the majority of the wifi card is housed inside the laptop, so its not easily dislodged. The USB adaptor is fine for wireless networking indoors, but too much of a risk for roaming outdoors.
I have had this problem from bios revision 1.70 to 1.8C, and I still have it with revision 1.90. Im planning to take the wifi card back to the shop for an exchange, but I have a very bad feeling that the same thing is going to happen with the replacement card. Im not convinced that the current wifi card is defective, because it works perfectly when it gets resources.
I have tried to manually configure the resources on the devices, but I run into one major problem. Windows seems to be LOCKED into automatic settings. The automatic settings checkbox is completely greyed out, making it impossible for me to clear the check box. I have not seen anything in the bios that can help me resolve this problem.
I have noticed that there are a lot of devices running off IRQ (Interrupt Request) 19, when viewing the resources by type in the device manager. These devices are:
Standard Enhanced PCI to USB Host Controller
Standard OpenHCD USB Host Controller x 2 (two entries)
Texas Instruments OHCI Compliant IEEE 1394 Host Controller
Texas Instrumetns PCI-1410 CardBus Controller
When the wifi card is working it also runs off IRQ 19, but as I stated before Windows is locked into automatic settings and will not let me configure the hardware resources manually.
The Equium A60-157 does not come with onboard, but it has the potential to. Wifi l.e.d. on front panel, location for physical wifi switch on side panel and wifi icon on F8. Does anyone know if Toshiba offer an upgrade service, or can I install onboard wifi myself?
ANYONE, PLEASE HELP ME WITH THESE ISSUES!!!
Thanks for you time!

Hi
I found this for you:
Two devices have been assigned the same input/output (I/O) ports, the same interrupt, or the same Direct Memory Access channel (either by the BIOS, the operating system, or a combination of the two). This error message can also appear if the BIOS did not allocate enough resources to the device (for example, if a universal serial bus (USB) controller does not get an interrupt from the BIOS because of a corrupt Multiprocessor System (MPS) table).
You can use Device Manager to determine where the conflict is and disable the conflicting device. On the General Properties tab of the device, click Troubleshoot to start the troubleshooting wizard.
Try to disable the conflict devices. It will be interesting to know if the problem will occur again.
In my opinion you should contact Service partner and ask them if the unit is prepared for Wi-Fi module. Sorry but I am not sure about that and I dont want to give you a wrong information about that.

Equium A60 won't boot properly

A puff of smoke came from the keyboard of my Equium A60 and now it can only be booted in Safe Mode. Everything seems to work OK in Safe Mode, but if I try to boot it normally it says: 'No bootable disc in DVD drive' and the following message appears:
For Realtek RTL8139(x)/8130/810x PCI Fast Ethernet Controller v 2.13(020326) PXE-E61-Media Test Fail, Check Cable.
PXE-MOF-Exiting PXE ROM.
I understand that this means that it is trying to boot from the LAN !
When operating in Safe Mode the C-drive seems OK, so there does not seem to be anything wrong with the HDD. But in Safe Mode I cannot connect to the Internet of course.
I'm using Windows XP.
Anyone out there who can tell me what's going on ?
All help gratefully received.

Hello Collin
> A puff of smoke came from the keyboard of my Equium A60
Please do not make experiments anymore and contact authorized service partner in your country as soon as possible. Who knows what is wrong there. Smoke can indicate to serious hardware problem and you should be careful with it.
I repeat again: please do not risk because it can end with more damaged hardware. Contact service and explain them the situation. Address and phone number you can find under http://eu.computers.toshiba-europe.com Support & Downloads Find an ASP.
Bye

Can I use board from Equium A60 for my Satellite A60?

Hi,
I need help pleas! I have a Satellite A60-793, and I need a new board. I can buy a board of a Equium A60. Will that work on my system? My system have a P4 3.0Ghz.
Best Regards
José Nunes

Hi
Usually there are different Satellite A60 series and different Equium A60 series but both notebooks are very similar and you should be able to install the motherboard from a Sat A60 into the Equium A60.
The motherboards dimensions (width + length) are the same.

Crystal Report 2011 CrystalDecision.reports.web.dll Not found

Dear All,
Scenario 1:
I want to use crystal report in my web application developed in 2008 so,
I have been install Crystal Report 2011 Evaluation copy download from SAP Site.
But it will not found following necessary dll file after installing it.
1. CrystalDecision.reports.web.dll
2. CrystalDecision.reportsource.dll
3. CrystalDecision.reports.engine.dll
4.   CrystalDecision.reports.shared.dll
   This files are necessary to load crystal report on webForm.
Scenario 2:
    I want to download Crystal report 2011 run-time but i found it with must install visual studio 2010 setup.,
so, i need crystal report 2011 run-time which will run with dependency of VS 2010 and with both .net framework 3.5
and 4.0
So,Can anybody tell me solution about this scenarios.

Hi,
There is no .NET SDk for CR 2011. It does not install any SDk assemblies.
No SDk means No runtimes.
[http://forums.sdn.sap.com/thread.jspa?messageID=10937322#10937322|http://forums.sdn.sap.com/thread.jspa?messageID=10937322#10937322]
[https://weblogs.sdn.sap.com/pub/wlg/25302|https://weblogs.sdn.sap.com/pub/wlg/25302]
[http://forums.sdn.sap.com/thread.jspa?messageID=10814217#10814217|http://forums.sdn.sap.com/thread.jspa?messageID=10814217#10814217]
[1606608 - Where is the SDK for VS .NET in Crystal Reports 2011? |http://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes_boj/sdn_oss_boj_bi/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/scn_bosap/notes%7B6163636573733d36393736354636443646363436353344333933393338323636393736354637333631373036453646373436353733354636453735364436323635373233443330333033303331333633303336333633303338%7D.do]
Use either CR 2008 + VS 2008 or VS 2010 + CR for VS 2010
- Bhushan.
Edited by: Bhushan Hyalij on Feb 9, 2012 1:32 PM

Satellite A60-672 hangs and will not boot up properly

Hi,
I have a Toshiba Laptop A60-672 it had been running slow but now when I turn the laptop it goes straight into the option screen where I choose safe mode or last known good configuration, every option I choose goes into the windows screen as if xp is loading up the blue bar runs across the bottom of the screen then you get a quick click of a blue screen then it reboots back to the screen of safe mode and last know good config ??
Can anyone advise me
Thanks and Regards

Hi
The same happens on my brothers notebook because the files and sectors on the HDD were corrupted. This is happened after trying changing the partitions size.
I have booted from the original Microsoft Windows booting CD and went to the reparation console. I think you have to press the R to start the reparation in the Windows setup.
Then in the reparation console I have used the chkdsk /r option to solve this problem.
And I was successful try it!

Equium will not boot - how to access Recovery partition?

Hi, my sister has a 2008 Equium A200-1V0 with Vista 32-bit which will not boot (probably due to virus rootkit damage). It loads the BIOS but then goes straight to black screen with flashing cursor.
F8 does not work.
F2 goes to Phoenix TrustedCore Setup utility. The Toshiba hard drive and CD-ROM drive are listed in Main and Boot in the correct order.
Using F12 I can get it to boot from a Win7 64-bit repair disc I burned using my laptop.
However, this does not recognise the OS nor any image or restore points (because it is 64-bit) but it will load Command Prompt.
In *Command Prompt*, I can start Notepad and when I click File/ Open and double click on Computer it shows 4 Hard drives as follows:
Local Disk (C:)
Data (D:) 42 GB free of 54.5 GB
WinRE (E:) 1.11 GB free of 1.46 GB
Boot (X:) 29.0 MB free of 31.5 MB (which is used by the Repair disc)
So the C: drive is listed but without capacity.
*CHKDSK*
chkdsk c: /r and press return
"The type of the file system is NTFS.
Unable to determine volume version and state. CHKDSK aborted.
Failed to transfer logged messages to the event log with status 50.
*Running TESTDISK*
Analysis:
Partition Start End Size in Sectors
1 P Windows RE(store) 0 32 33 191 89 26 3072000
2 * HPFS - NTFS 191 89 27 7477 118 1 117051392
3 P HPFS - NTFS 7477 118 2 14592 190 62 114307072 (data)
* = Primary bootable
When doing Quick Search and then P - list files, of the second partition it reports:
"Can't open filesystem. Filesystem seems damaged."
So what I would like to do is boot up from Windows Restore on the E drive.
My question is to any Toshiba experts: When F8 does not work how do I use the recovery partition???
Laptop is:
Part Number : PSAF5E-002005KS
Key Features
- Intel Pentium Dual-Core Processor T2310
- Genuine Windows Vista Home Premium Edition
- DVD Super Multi (Double Layer) drive
- 2,048 (1,024 + 1,024) MB RAM (667 MHz)
- 15.4 " WXGA TFT display 1,280 x 800

*UPDATE*:
I have borrowed a genuine Windows Vista Home Premium 32-bit dvd and booted up with that.
Clicked on "Repair your Computer"
Then it goes striaght to System recovery Options but no Operating System is shown. Click Next.
Then:
"Choose a Recovery Tool.
Operating system: Unknown on (Unknown) Local Disk"
*Startup Repair*
This takes 1 second.
Root cause found
System volume on disk is corrupt.
*System Restore*
"X - To Perform an offline System Restore, you must specify which Windows installation you would like to restore.
For example, if the installation located in "C:\Windows" should be restored enter the following command:
rstrui.exe /OFFLINE:C:\Windows "
*Windows Complete PC Restore*
" No valid backup locations could be found.
Windows cannot find a backup on the hard disks or DVDs on this computer. Attach the correct hard disks or insert the last backup DVD and then start the restore process again. "
Windows Memory Diagnostic Tool
Windows cannot check for memory problems...[snip]
*Command Prompt*
This is working fine.
CHKSDK C:
The type of file system is NTFS.
Unable to determine volume version and state. CHKDSK aborted.
The HDD is 120 GB and is split by Toshiba into 3 partitions.
C:\ drive (56GB) is bootable with Windows - this is corrupted.
D:\ drive (55 GB) has all Data - fully accessible
E:\ drive is CDROM
F:\ drive (1.46 GB) is the WinRE recovery partition - this is fully accessible.
So my question still remains: can I recover my Toshiba laptop using this recovery partition?
PLEASE NOTE: as mentioned above, pressing F8 during boot has no effect and therefore Safe Mode cannot be accessed.

Equium A60 - DVD drive does not read data discs

Hello
I am having a problem with my DVD drive on my Toshiba Equium A60 laptop. The DVD drive (Pioneer DVD-RW DVR-K13A ) will play shop bought films etc without a problem. it will also read a blank DVD when you put it in the drive but once information/Data is on the disc it wont detect the disc.
I am not really that good with computer so any help would be most grateful. The computer used to play everything it just stopped doing it a few months back.
Many thanks Phil

The issue is clear.
Fact is that not all CDs and DVDs are supported and compatible. There could be always an issue with a reading or writing
The same happened to me too I had to test different CDs and DVDs from different manufacturers and finally some medias worked
In your user manual you should find a list of medias which were tested and should run properly check it!
bye

Equium A60 does not start after BIOS update

I have an Equium A60. After being caught with some very nasty malware and a trojan I made the disiccion to reformat the machine and reinstall the o.s..
All went well until I updated the bios. Machine crashed and now I cannot get it to reboot. Press the power button and the machine will start for 3-4 seconds and then shuts down.
I know this is due to the bios and want to know if there is any way that i can reset this back to it original settings?
thanks in advance for your help

Hi Rob.
The model of my laptop is EA60-152 / PSA67E.
Yes i did upgrade from the Toshiba website.
I should have never done this it was working after the reinstall of the o.s and so i should not have tried anything else(never fix something that aint broke).
The only place i have found for a new motherboard is Toshiba. But the price is nasty. Talk about what a fool am i.
Never mind though i keep on thinking that there may be an answer or a scrap one that i can rob a bios chip from. Other than that a very nice paperweight me thinks..!!!!
If i get an answer than i will post it here..

Equium M50 will not recognise the LAN port - error: Network Cable unplugged

I own a Toshiba Equium M50 and have problems with the Marvell Yukon 88E8036 PCI-E Fast Ethernet Controller.
I used to connect via an 'ADDON' Modem/ADSL Switch and had no problems. I then replaced the ADDON with a 'NETGEAR' DG834G ADSL Modem/Router to gain the wireless port, and since then my machine will not recognise the LAN port. <error: Network Cable unplugged>.
I know that the cables are OK as I used them with other laptops and had no trouble. I can also plug in a PCI card to connect without any problems. It looks to me as if the Marvell Yukon 88E8036 PCI-E Fast Ethernet Controller has a problem with the netgear Modem/Router.
Anyone out there with a similar experience and some advice/suggestions?
PLEASE

Hi
For me it doesnt show like a LAN card problem but your router is a problem.
Check the device manager if the LAN card was properly recognized. If there are no yellow exclamation marks so everything is ok!
You can try to delete the LAN card from the device manager and after new reboot install the LAN driver again.
The issue has stared after installing or connecting the new Netgear modem router.
Therefore I would recommend to checking firstly the settings or to update the firmware on this router.
I have found additionally these useful websites
http://compnetworking.about.com/od/windowsnetworking/f/cableunplugged.htm
http://www.experts-exchange.com/Networking/Broadband/DSL_Cable/Q_20381405.html

I bought a movie from itunes and it will not play. gives me a prompt to sign into itunes to play, but am already logged in?

I had to wipe and re install Itunes on my mac minni. When I bought the hobbit, it will not play. I get a prompt to sign into Itunes and the movie will not play. I am logged into Itunes and still no luck?

I am having the same trouble

I have an original iPad and when I try to login on Yahoo through Safari it will not log me in. What could be the problem?

My original iPad will not log me into Yahoo through Safari. It's been this way for one week. I can access Yahoo on my PC with no problem so I think the problem is my iPad or Safari.

Your description of the behavior of the ipad1 during a login attempt is more precise than mine, it is the exactly as my ipad1 reacts and supposedly as all other iPad1 will behave. This could be solved either by apple with an update of the safari browser for ipad1. I do not think that apple will do that. Also yahoo could undo the change of the login procedure which they recently made and which is incompatible do the ipad1s safari browser. They hardly will do that either if not be urged by lots of ipad1 users.
!!!! SO SEND COMPLAINS TO YAHOO, PHONE THE HOTLINE ETC !!!!!!
Otherwise you have to buy a new iPad or to change the email provider.

Re: Equium A60-672 will not log on - winlogon.exe - Ordinal not found

Similar Messages

Maybe you are looking for