Re: Fail to recover the cisco ios 3560

Dear Stephen,
yesterday i was succeeded to upgrade the flash. after the upgradtion it gives me a message
File "xmodem:" successfully copied to "flash:c3560-ipbase-mz.122-25.SEB4.bin"
!--- If the Xmodem file transfer fails for some reason, restart the process.
!--- If the Xmodem file transfer is successful, you return to the
!--- switch: prompt.
switch:
then i apply the command
switch: boot flash: flash:c3560-ipbase-mz.122-25.SEB4.bin
after this command it takes 2mins then restarts and finally it giving a error like this
now i am unable to go in to this mode switch:
try my level best but unable to do it.

Similar Messages

How to recover the cisco ios 3560

dear concerned,
I am unable to upload the ios image cisco 3560. please help me in this regard.
Base ethernet MAC Address: 00:18:ba:e5:5f:00
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
flashfs[0]: 0 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 1024
flashfs[0]: Bytes available: 15997952
flashfs[0]: flashfs fsck took 8 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs) installed, fsid: 3
done.
Loading "flash:c3560-ipbase-mz.122-25.SEB4/c3560-ipbase-mz.122-25.SEB4.bin"...fl
ash:c3560-ipbase-mz.122-25.SEB4/c3560-ipbase-mz.122-25.SEB4.bin: no such file or
directory
Error loading "flash:c3560-ipbase-mz.122-25.SEB4/c3560-ipbase-mz.122-25.SEB4.bin
Interrupt within 5 seconds to abort boot process.
Boot process failed...
The system is unable to boot automatically. The BOOT
environment variable needs to be set to a bootable
image.
switch: dir flash:
Directory of flash:/
15997952 bytes available (1024 bytes used)
please help me in this regared

dear concerned,
I am unable to upload the ios image cisco 3560. please help me in this regard.
Base ethernet MAC Address: 00:18:ba:e5:5f:00
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
flashfs[0]: 0 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 1024
flashfs[0]: Bytes available: 15997952
flashfs[0]: flashfs fsck took 8 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs) installed, fsid: 3
done.
Loading "flash:c3560-ipbase-mz.122-25.SEB4/c3560-ipbase-mz.122-25.SEB4.bin"...fl
ash:c3560-ipbase-mz.122-25.SEB4/c3560-ipbase-mz.122-25.SEB4.bin: no such file or
directory
Error loading "flash:c3560-ipbase-mz.122-25.SEB4/c3560-ipbase-mz.122-25.SEB4.bin
Interrupt within 5 seconds to abort boot process.
Boot process failed...
The system is unable to boot automatically. The BOOT
environment variable needs to be set to a bootable
image.
switch: dir flash:
Directory of flash:/
15997952 bytes available (1024 bytes used)
please help me in this regared

I can not install the Cisco IOS on the AP 1200.

I can not install the Cisco IOS on the AP 1200 series.
Displays error:
ap: tar -xtract tftp: / / 192.168.1.11/temp/c1200-k9w7-tar.123-7.JA3.tar flash:
tftp: / / 192.168.1.11/c1200-k9w7-tar.123-7.JA3.tar: connection timed out
These procedures were done:
flash_init
tftp_init
ether_init
set IP_ADDR 192.168.1.21
set NETMASK 255.255.255.0
set DEFAULT_ROUTER 192.168.1.11 (PC's IP with FTP).
Can someone please help?

Resolved
Recommendations were made by Mr. Talal Fraij.
Tftpd32 application was used.
Image File (C1200-k9w7-tar.123-7.JA3.tar) root directory.
Antivirus disabled.
Firewall disabled.
I want to acknowledge the help of
Mr. Talal Fraij.
If not for your help would be without sleep for a long time .. kkkk

How to copy configuration files to and from the cisco ios routers that use SNMP

Hello,
I went on the page : https://supportforums.cisco.com/docs/DOC-1860
You explain how to get a config file and send it to a tftp server or oppositely.
I face this problem:
id090365:~> snmpset -v2c -c communitystring hostipaddress .1.3.6.1.4.1.9.9.96.1.1.1.1.2.98 i 1
Error in packet.
Reason: noCreation (That table does not support row creation or that object can not ever be created)
Failed object: SNMPv2-SMI::enterprises.9.9.96.1.1.1.1.2.98
Do you have any idea?
Thanks,
Olivier

I hadn't seen any snmp guides using snmpv3 and scp as transport protocol. For those looking to implement, here is what worked for me.
As with the other snmp config copy guides you will need to download the respective MIBS and load them in the snmp.conf file.
This post will specifically cover the snmpset commands for a v3 setup.
SNMP Environment:
Name        : net-snmp
Version     : 5.7.2
Release     : 17.fc20
snmp conf file in ~/.snmp/snmp.conf
   contains
defSecurityName XXX <- replace with v3 username
defContext ""
defAuthType SHA
defPrivType AES
defSecurityLevel authPriv
defAuthPassphrase ***** <-replace with authentication pass
defPrivPassphrase ***** <-replace with encryption pass
defVersion 3
showMibErrors no
mibs ALL
I would verify basic snmpv3 functionality with a snmpwalk of something simple like sysUpTime. When that's good proceed to the CONFIG-COPY snmp commands.
This is my bash script that does the entire copy asking only for a single argument of IP/Hostname of the device being backed up. The 2>/dev/null shown in the script or at the cli below redirects STDERR to null to avoid the MIB modules parsing errors.
#!/usr/bin/bash
DEVICE=$1
RANNUM=42
USER=******
PASS=******
SERVER=X.X.X.X
DATE=$(date +"%m_%d_%y")
snmpset $DEVICE ccCopyProtocol.$RANNUM i 4 ccCopySourceFileType.$RANNUM i 4 ccCopyDestFileType.$RANNUM i 1 ccCopyServerAddress.$RANNUM a "$SERVER" ccCopyFileName.$RANNUM s "$DEVICE.$DATE" ccCopyUserName.$RANNUM s $USER ccCopyUserPassword.$RANNUM s $PASS ccCopyEntryRowStatus.$RANNUM i 4 2>/dev/null
Once run you can check the status of the copy with the following command.
[root@localhost hlsb]# snmpwalk sbs-tech-switch ciscoConfigCopyMIB 2>/dev/null
CISCO-CONFIG-COPY-MIB::ccCopyProtocol.42 = INTEGER: scp(4)
CISCO-CONFIG-COPY-MIB::ccCopySourceFileType.42 = INTEGER: runningConfig(4)
CISCO-CONFIG-COPY-MIB::ccCopyDestFileType.42 = INTEGER: networkFile(1)
CISCO-CONFIG-COPY-MIB::ccCopyServerAddress.42 = IpAddress: 10.10.10.193
CISCO-CONFIG-COPY-MIB::ccCopyFileName.42 = STRING: sbs-tech-switch.07_09_14
CISCO-CONFIG-COPY-MIB::ccCopyUserName.42 = STRING: XXXX
CISCO-CONFIG-COPY-MIB::ccCopyUserPassword.42 = STRING: XXXX
CISCO-CONFIG-COPY-MIB::ccCopyNotificationOnCompletion.42 = INTEGER: false(2)
CISCO-CONFIG-COPY-MIB::ccCopyState.42 = INTEGER: successful(3)
CISCO-CONFIG-COPY-MIB::ccCopyTimeStarted.42 = Timeticks: (52270199) 6 days, 1:11:41.99
CISCO-CONFIG-COPY-MIB::ccCopyTimeCompleted.42 = Timeticks: (52270339) 6 days, 1:11:43.39
CISCO-CONFIG-COPY-MIB::ccCopyEntryRowStatus.42 = INTEGER: active(1)
CISCO-CONFIG-COPY-MIB::ccCopyServerAddressType.42 = INTEGER: ipv4(1)
CISCO-CONFIG-COPY-MIB::ccCopyServerAddressRev1.42 = STRING: "10.10.10.193"
After the successful copy completes the entry will exist for five minutes allowing for no further requests to be made with that particular random number. To send another request prior to the five minute clearing of the table send a "destroy" snmpset to clear the entry.
[root@localhost hlse]# snmpset sbs-tech-switch CISCO-CONFIG-COPY-MIB::ccCopyEntryRowStatus.42 i 6 2>/dev/null
CISCO-CONFIG-COPY-MIB::ccCopyEntryRowStatus.42 = INTEGER: destroy(6)
Hope this will save some time for those looking to implement a more secure snmp config copy setup.
V/R
Cody Hartley

HT201210 Fail to update the latest IOS on iphone at china because of firmware is not compactible

Anyone could give valuabe advise on how to resolve this issue?

Make sure you have the latest updates to the operating system
and to iTunes and then try again.
This message is frequently caused by the iPhone having been
hacked/modified/jailbroken to work with a wireless carrier other
than the one the iPhone is locked to. Such modification can
prevent updates succeeding, carrier unlocks completing and
may render your iPhone unuseable.
Where did you acquire this iPhone? Has it been modified?

ISE 1.1.3 en Cisco IOS SCEP

Hi,
I'm running Cisco ISE 1.1.3.124 and a Cisco IOS 2811 (c2800nm-spservicesk9-mz.150-1.M2.bin) which I configured the be a SCEP server.
PKI Authentication and enrollment of a Cisco switch with this SCEP server is running well but BYOD clients enrollment via EAP-TLS (1024/2048) giving me the following error on the Cisco IOS SCEP server:
SCEP#
.Mar 17 15:21:59.446: Sun, 17 Mar 2013 15:21:59 GMT 10.0.0.164 /cgi-bin/pkiclient.exe ok
        Protocol = HTTP/1.1 Method = GET Query = operation=PKIOperation&message=MIAGCSqGSIb3DQEHAqCAMIACAQExCzAJBgUrDgMCGgU
AMIAGCSqGSIb3DQEHAaCAJIAEggPoMIAGCSqGSIb3DQEHA6CAMIACAQAxggEvMIIBKwIBADATMA4xDDAKBgNVBAMTA2lzZQIBA
TANBgkqhkiG9w0BAQEFAASCAQAmbK6WZ5L6gw+uh7h4Qi53XL76QsBNcY8E6cMxWDp8hWbLvujNOylSvJLF
.Mar 17 15:21:59.446:
.Mar 17 15:21:59.454: CRYPTO_CS: received a SCEP request, 3652 bytes
.Mar 17 15:21:59.454: CRYPTO_CS: read SCEP: registered and bound service SCEP_READ_DB_10
.Mar 17 15:21:59.482: CRYPTO_CS: scep msg type - 19
.Mar 17 15:21:59.482: CRYPTO_CS: trans id - 9871e81c65121310b77df8b341c7c887a5392da2
.Mar 17 15:21:59.486: CRYPTO_CS: failed to open env data
.Mar 17 15:21:59.486: CRYPTO_CS: read SCEP: unregistered and unbound service SCEP_READ_DB_10
.Mar 17 15:21:59.486: CRYPTO_CS: failed to read SCEP request
.Mar 17 15:21:59.502: Sun, 17 Mar 2013 15:21:59 GMT 10.0.0.164 /cgi-bin/pkiclient.exe ok
SCEP#
I'm stuck now on the message: failed to open env data. So can anyone explain what the meaning is of this message or maybe know if IOS SCEP with ISE is supported ?
Thanks in advance.
greetz Michel
btw the tracelog of the switch enrollment with IOS SCEP is below:
SCEP#
.Mar 17 14:57:10.932: Sun, 17 Mar 2013 14:57:10 GMT 10.0.0.161 /cgi-bin/pkiclient.exe ok
        Protocol = HTTP/1.0 Method = GET Query = operation=PKIOperation&message=MIIGWgYJKoZIhvcNAQcCoIIGSzCCBkcCAQExCzAJBgUrDgMCGgUAMIIDAAYJKoZI
hvcNAQcBoIIC8QSCAu0wggLpBgkqhkiG9w0BBwOgggLaMIIC1gIBADGBujCBtwIB
ADAgMBsxGTAXBgNVBAMTEGNhLndlc3R3aWp6ZXIubmwCAQEwDQYJKoZIhvcNAQEB
BQAEgYAo/LNaINm+tcgzF8V8d7d5x
.Mar 17 14:57:10.932:
.Mar 17 14:57:10.936: CRYPTO_CS: received a SCEP request, 2210 bytes
.Mar 17 14:57:10.940: CRYPTO_CS: read SCEP: registered and bound service SCEP_READ_DB_1
.Mar 17 14:57:10.948: CRYPTO_CS: scep msg type - 19
.Mar 17 14:57:10.948: CRYPTO_CS: trans id - 59D142A6D0F525668626A435229BAAF1
.Mar 17 14:57:11.040: CRYPTO_CS: read SCEP: unregistered and unbound service SCEP_READ_DB_1
.Mar 17 14:57:11.040: CRYPTO_CS: received an enrollment request
.Mar 17 14:57:11.040: CRYPTO_PKI: creating trustpoint clone ise1
.Mar 17 14:57:11.040: CRYPTO_CS: checking policy for enrollment request ID=1
.Mar 17 14:57:11.040: CRYPTO_CS: request has been authorized, transaction id=59D142A6D0F525668626A435229BAAF1
.Mar 17 14:57:11.040: CRYPTO_CS: locking the CS
.Mar 17 14:57:11.040: CRYPTO_CS: added CDP extension
.Mar 17 14:57:11.044: CRYPTO_CS: added key usage extension
.Mar 17 14:57:11.044: CRYPTO_CS: Validity: 13:57:11 UTC Mar 17 2013-13:57:11 UTC Oct 3 2013
.Mar 17 14:57:11.128: CRYPTO_CS: writing serial number 0x2.
.Mar 17 14:57:11.180: CRYPTO_CS: file opened: nvram:ise.ser
.Mar 17 14:57:11.180: CRYPTO_CS: Writing 32 bytes to ser file
.Mar 17 14:57:13.864: CRYPTO_CS: reqID=1 granted, fingerprint=2
.Mar 17 14:57:13.864: CRYPTO_CS: unlocking the CS
.Mar 17 14:57:13.864: CRYPTO_CS: write SCEP: registered and bound service SCEP_WRTE_DB_1
.Mar 17 14:57:13.984: CRYPTO_CS: write SCEP: unregistered and unbound service SCEP_WRTE_DB_1
.Mar 17 14:57:13.988: CRYPTO_CS: Certificate generated and sent to requestor
.Mar 17 14:57:13.988: CRYPTO_CS: removing trustpoint clone ise1

Michel,
Officially supported it is not:
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCud86973
Some people mentioned varios degrees of "having it working".
In your case it's the envelope data which appears to be a problem for IOS.
M.

Basic questions about CISCO IOS

Hi everybody, Jack here,
I have some basic questions about the Cisco IOS, could someone help me addressing some of them please? Any feedback would be greatly appreciated.
Basically, I have two IP addresses assigned by our Cable ISP. From what I understood you can configure a Cisco router for multiple IP addresses using the IOS, thereby allowing someone like myself to take advantage of having multiple IP addresses. This may seem unnecessary to some, but I've always wanted to put the 2nd IP address to use, since after all, I've been paying for it.
I was just wondering if someone could confirm that what I'm hoping to accomplish is indeed within the capability of the Cisco IOS (i.e. Fully utilize my 2 IP addresses). As well, if someone could kindly suggest a decent CISCO router for online gaming home use that would be super awesome!
Thank you all so much for reading through the wall of text:)
Jack

Jack
Certainly using multiple IP addresses is in the capability of Cisco IOS routers. How they can be used depends on the relationship of the IP addresses. I am assuming that we are talking about IP addresses assigned for the user to use and that the IP address for the ISP connection is not one of these that we are talking about.
If both of the IP addresses that you have been assigned are within the same subnet then you would assign one of the addresses to the router interface to establish IP communication between the router and the ISP and to enable Internet connectivity for the devices inside your network that will use the router as their gateway to the Internet. The other address that is assigned can be used for address translation and in particular for static address translation which would make one of your devices inside to be reachable for connections initiated from the Internet (if that is something that you might want to do).
If the addresses that are assigned to you are in different subnets then you could assign one address to the outside router interface and assign the other address to the router inside interface. Or you could use the second address for address translation.
I do not have much expertise with online gaming, but I would think that either the Cisco 881 router or the 890 router might be appropriate for you. If 100 Mb connection is sufficient then probably the 881 would be the one to look at. If you need Gig connection then look at the 890.
HTH
Rick

Wrongly updated the newest iOS for my iphone 3GS

As I pluged my iPhone 3GS into a new laptop, I wrongly updated the newest iOS version into my phone. This causes a few content loses and the phone runs very slowly. How can I restore/recover the right iOS at my 3GS? Thanks a lot.

Downgrading is not supported, so that is out of question.
About the lost contents. Plug your iPhone in to iTunes of your previous laptop (if you still have it); right click on your phone's name and hit "Restore from backup". Later you can move your iTunes library from your old laptop to your new laptop by following this.
http://support.apple.com/kb/HT1751
Message was edited by: impious-rocker

Cisco IOS CA

Team,
I am using Cisco IOS XE Software, Version 03.15.00.S - Standard Support Release Cisco IOS Software, CSR1000V Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(2)S, RELEASE SOFTWARE (fc3) to support my Cisco IOS CA.
In a nutshell, I am trying to support a FlexVPN - Win7 VPN client as per tac document id 115907
In this document, it states that OpenSSL CA is used but a Cisco IOS CA can also be used. When testing I am at a point where my certificates do not match the example:
The TAC document example:
X509v3 extensions:
X509v3 Key Usage: F0000000
Digital Signature
Non Repudiation
Key Encipherment
Data Encryption
My lab version:
X509v3 extensions:
X509v3 Key Usage: A0000000
Digital Signature
Key Encipherment
Question - How do I get these alternate extensions using the Cisco IOS CA?
Chris

Hi Marcin,
You have the same as I - I got my lab working - I tripped up on the KeyUsage thinking that my VPN headend Cisco CSR needed these same extensions as my Win7 client did. When I adjusted my Win7 CSR to feature these extra extensions and re-enrolled, everything is working.
Thanks for your help,
Chris

Cisco IOS IPS in Cisco 2921/k9 router

Hi All,
I have a router of Cisco 2921 series (C2921/K9) basic box with IP BAse IOS image (SL-29-IPB-K9 IOS). I would like to enable IOS Level IPS feature on this Router now. Based on the Cisco Document i have found i need to purchase an additonal subscripton license to enale the IPS feature. My querry is-
Will it support on the Basic IP Base IOS or do i need to change the IOS?
If i need to purchase the Subscription Licesne, how can i get the part number and cost for the same?
Do i need to buy any addtional module for this like (NME-IPS-K9) ?
Thanks in advance for your quick support
regards
Sunny

Hi Sunny
1. Yes you can enable IPS on IOS with the security license, without buying a subscription, but this would make little sense - new signatures are being released all the time so you would not be protected from recently discovered vulnerabilities/attacks.
2. Correct, the modules and appliances run a different kind of software and are much more powerful
3. If you add the module, you do NOT need the security license. It would still be advised to get a subscription license to get signature updates for the module.
I hope this helps, let us know.
regards
Herbert
jacob.samuel wrote:Dear Herbert,Thanks alot for the wonderful post. It clear most of my doubts. Still i kindly need to know few more points-1) Cant we enable IPS Feature on 2921/K9 router (with Sec license or 2921Sec/K9 bundle) without signature subscription license (is it a must? it is for getting updates of signatures and for support only, right?)2) I came to know from a distributor pre-sales engineer that the Cisco IOS Level Intrusion Protection is not going to provide the full feature of IPS like NME module or IPS Applinace. Is that right?3) If i add NME-IPS-K9 Module to my 2921 Router, without enabling Sec License, can i enable IPS feature on the Router. Or is it a must that i need to buy Sec License (SL-29-SEC-K9)?Attaching the Datasheet of NME-IPS-K9 module (Page num 5 above Table 3) mentione as follows-Cisco IOS Software Feature Sets and ReleaseTable 3 lists the required Cisco IOS feature sets and releases for Cisco IPS AIM and IPS NME on the Cisco 1841,
2800 and 3800 series Integrated Services Routers Note that, IPS NME on the Cisco 2900 and 3900 Integrated
Services Routers does not require a Security Feature license.
In that case if i buy a module i can install it on the 2921K9 box directly and can enable the IPS feature right? I dont need any License and additonal signature subscription here to enable the IPS feature (if i dont need signature updates and support) right?
thanks alot for the support.
regards
Sunny

Cisco IOS-XR with ACS

Hello, my question is if you have to configure the Cisco IOS-XR enabled router (it is a 12k series by-the-by) differently on the ACS side or is it added like any other normal router.

hi raul,
the ios-xr router will act as a NAS for the ACS. so the configuration will the same as any other NAS on the ACS.
Regards,
Anisha
P.S.: please mark this thread as answered if you feel your query is resloved

BGP support in Cisco IOS 15.1(3) T2

Because of security concerns I must update the IOS in my 2800 and 3800 series routers. After checking the available options and the
Cisco IOS Software Checker application the version of choice would appear to be 15.1(3)T2. But I must be able to support BGP and 15.1(3)T2 is not listed in the Cisco Feature Navigator.
Generally one might assume that if a previous version and image supported a feature, the update would also. But I cannot take any chance that this is true or not true. I need to know for sure before implementation.
Before I bring a system crashing down, I need to know if this IOS version, and which images of this version, support BGP.
Any assistance gratefully accepted.
Manny

Of course it support BGP.
However, 15.0(1)Mx would be the safest choice.

Cisco IOS Syslog Messages

Does anyone have a link that shows all the Cisco IOS syslog messages?
Such as this one for the ASA?
http://www.cisco.com/en/US/docs/security/asa/asa80/system/message/syslog.html
Thanks in advance.

This guide should give you what you want.
http://www.cisco.com/en/US/docs/ios/system/messages/guide/consol_smg.html

Cisco Aironet Conversion Tool Version 2.1 for Cisco IOS Software

I am trying to convert a LWAP to Cisco IOS and the tool wants to know the Admin Name*? This is a factory radio sent to me as LWAP. I cannot seem to find out what the Admin Name is, I have tried Admin and Cisco not sure what else to try.

Hi Brian,
That tool is used for the IOS to LWAPP upgrade only. The AP can be converted back to Autonomous (IOS) using the following method;
Reverting the Access Point Back to Autonomous Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob

Cisco AP1231G failed to flash the interface on failed boot

Hello,
I have an issue with Cisco AIR-AP1231G-E-K9 since I have rebooted it to reload startup conf :
Now, radio is disabled. On web interface, Radio mac address is 0000.0000.0000
I tried a no shut on Dot11radio0 but didn't work.
I tried to upload a new firmware but didn't solve the issue.
Here you can find result of sh log :
POZAPA-0004#sh log
Syslog logging: enabled (0 messages dropped, 3 messages rate-limited,
0 flushes, 0 overruns, xml disabled, filtering disabled)
Console logging: level debugging, 38 messages logged, xml disabled,
filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
filtering disabled
Buffer logging: level debugging, 40 messages logged, xml disabled,
filtering disabled
Logging Exception size (4096 bytes)
Count and timestamp logging messages: disabled
Trap logging: level notifications, 34 message lines logged
Logging to 10.128.2.12, 34 message lines logged, xml disabled,
filtering disabled
Log Buffer (4096 bytes):
101.img)
*Mar 1 00:00:11.895: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-
k9w7-mx.123-7.JA3/5101.img)
*Mar 1 00:00:19.202: Failed to flash the interface on failed boot
*Mar 1 00:00:19.205: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-
k9w7-mx.123-7.JA3/5101.img)
*Mar 1 00:00:19.264: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-
k9w7-mx.123-7.JA3/5101.img)
*Mar 1 00:00:26.574: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-
k9w7-mx.123-7.JA3/5101.img)
*Mar 1 00:00:34.181: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-
k9w7-mx.123-7.JA3/5101.img)
*Mar 1 00:00:34.241: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-
k9w7-mx.123-7.JA3/5101.img)
*Mar 1 00:00:41.548: Failed to flash the interface on failed boot
*Mar 1 00:00:41.548: Tried to send command 0229 while the MAC not running
*Mar 1 00:00:41.549: Tried to send command 0229 while the MAC not running
*Mar 1 00:00:41.549: Unable to read RID_CHAN_POWER
*Mar 1 00:00:41.549: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid power levels available
*Mar 1 00:00:41.549: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid power levels available
*Mar 1 00:00:43.640: %SYS-6-LOGGERSTART: Logger process started
*Mar 1 00:00:43.642: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 01:00:43.768 GMT: %SYS-6-CLOCKUPDATE: System clock has been updated from 00:00:43 UTC Fri Mar 1 2002 t
o 01:00:43 GMT Fri Mar 1 2002, configured from console by console.
*Mar 1 01:00:44.703 GMT: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 01:00:45.270 GMT: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 01:00:45.270 GMT: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(7)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Tue 21-Mar-06 14:18 by ccai
*Mar 1 01:00:45.270 GMT: %SNMP-5-COLDSTART: SNMP agent on host POZAPA-0004 is undergoing a cold start
*Mar 1 01:00:45.286 GMT: %SSH-5-ENABLED: SSH 1.99 has been enabled
*Mar 1 01:00:45.296 GMT: Writing radio coredump to 'flash:/r0_00_0000_E6177677.rcore'
*Mar 1 01:00:46.151 GMT: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
Sep 23 10:05:02.004 GMT: Writing radio coredump to 'flash:/r0_00_0000_BA624BBC.rcore'
Sep 23 10:05:05.015 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:05:06.073 GMT: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
Sep 23 10:05:38.648 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:05:38.708 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:06:12.048 GMT: Failed to flash the interface on failed boot
Sep 23 10:06:12.050 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:06:12.111 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:06:45.463 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:07:20.311 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:07:20.371 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:07:54.989 GMT: Failed to flash the interface on failed boot
As you can see , I have multiples line saying that radio is loading firmware but at the end we have "Failed to flash the interface on failed boot"
Did someone had this issue already ?
tanks for your answer.

Sep 23 10:06:12.111 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-k9w7-mx.123-7.JA3/5101.img)
This is the reason why your 802.11b radio won't come up. The radio-specific firmware is either missing or corrupted.
Most effective way is to overwrite and unpack the entire TAR file. So let the AP boot normally. Don't worry about the radio for the time being.
Make sure you have the TAR file located in the correct folder of your TFTP server. Use the command "archive download-sw /over /force tftp://<TFTP IP address>/filename.tar".
Once the process is complete the AP will reboot.

Re: Fail to recover the cisco ios 3560

Similar Messages

Maybe you are looking for