Re@lted t0 bluetooth dongle, stack and configuration.. .......

Hi to all,
Those r new or require some more info realted to STACK and statring the prohect read the following page
http://www.cs.hku.hk/~fyp05016/kyng/bt_j9.htm
This is may be benifical to u.
Anyhow, i am making the my final year project related to Bluetooth and i am trying to use AVETANA which can be dowloaded from the following link:
http://www.avetana-gmbh.de/avetana-gmbh/downloads/relicense.idmexieubncmqxqphuvrohkpjcgwbv.eng.xml
After u visit this link u will see that, avetana require three bluetooth address. I have inputed the address 22:22:22:22:22:22 ( or 22-22-22-22-22-22). I have extracted this address from start-run-ipconfig/all after i install the device dirver software "BlueSoleil_1.6.2.1" in Win XP OS. My bluetooth dongle is "ISSC Bluetooth Device" which i extracted from Device Manager (Start - Right Click My computer - Properties - Hardware - Device Manager). Moreover my VID and UID of the bluetooth dongle is "USB\VID_1131&PID_1001". I have even cheked the microsoft XP site
http://support.microsoft.com/kb/841803/
for the sake of conformation that whether my bluetooth dongle is supported my Win XP sp2 and the above VID and UID is not present there.
Now the problem is that site doesnot accept my above written address, and so i am unable to download the avetana,,,
In the end(after searching on the net) I have concluded that might the following reason may be there:
1) my bluetooth dongle is either of some local company manufacturer which is not recognized by win XP
2) i am using wrong device driver
3) i am unable to configure properly the bluetooth device.
Moreover, even after installing the device driver (BlueSoleil_1.6.2.1) i am unable to see any bluetooth icon in the Control panel so that i can see/change the bluetooth property.
Plz help me up..
and if i am thinking correct, which company dongle i should purchase or which other bluetooth stack (say like atinav, BlueCove) i should use...
I even want to know that with respect to stack (say atinav) i need to purchase the dongle or not..
moreover, i donot want to buy any stack as this is only my academic project so i donot have so much money to buy a stack (like atinav)
thx in advance..

Bluetooth forum
http://vietcovo.com http://forum.vietcovo.com

Similar Messages

Bluetooth USB dongle stack download for Windows 7

I have a Toshiba USB bluetooth dongle. The software will not install using Windows 7 and the dongle does not work at all on my PC. The only download I could find for the software was for Toshiba notebooks! Where can I download the software/drivers? I must say that the support for updates to Windows 7 is very poor or very well hidden. Why is the stack only free for notebook users? Must I avoid Toshiba's products in future because the support seems to be non-existent. Any help would be appreciated.

Hi
Please take a look here on this Toshiba BT portal:
http://aps2.toshiba-tro.de/bluetooth/
Here you can download the newest Toshiba BT stack!
Here is also an explanation why the BT stack is valid for 30 days:
http://aps2.toshiba-tro.de/kb0/FAQ81021V0000R01.htm
This message will appear ONLY if you are using non-Toshiba Bluetooth adapter.
The usage of Toshiba BT stack on all Toshiba products is NOT limited.

Msi bluetooth headset and msi bluetooth dongle

have both, dongle installed and working, but it cant ever find the headset... any idea?

From my understanding the dock for the bluetooth headset was made for the original iPhone. The dimensions of the iPhone 3g are different, so the dock would not be the right size for the phone. You can still charge the bluetooth headset either in the dock that came with it, or with the cable that also was included in the box. Hope this helps

Conflict Between Toshiba Bluetooth Stack and Power Drawers on Tecra M5

There seems to be a bug in TosBtShell.dll and I'm hoping this alert might get it repaired in a future revision. Maybe also it will save others the considerable effort it cost me to track down the problem on my new Tecra M5. I've had to abandon Toshiba Bluetooth Stack and now use the one in XP SP2.
When Bluetooth Manager is running, TosBtShell.dll puts the item 'to Bluetooth' next to 'Send To' in the context menu for files and folders. Unfortunately it conflicts with the shell enhancement software Power Drawers http://www.dynamickarma.com/powerdrawers.htm that I rely on to speed up access to my computer files. This software lets you right-click on a folder to display its contents in a list. You can then mouse to any folder in the list and that one also expands as a sub-list - and so on as deep as you like until you reach the folder or file that you want. Right-click an item in the cascade and you get a list of useful options. However if Bluetooth Manager is running when you do the right-click, Power Drawers crashes and you have to close and reopen explorer.exe to get it back.
The conflict stops if you remove 'to Bluetooth' from the context menu for files and folders. I proved this by using ShellExView from Nirsoft http://www.nirsoft.net/utils/shexview.html to disable the Registry key 'Bluetooth File Extenstion' [sic]. This key is associated with C:\WINDOWS\system32\TosBtShell.dll and CLSID {6BEF3D0B-53F0-4b0d-B91C-C19ED3D4C9D1}. Unfortunately the Registry key comes back again whenever you restart Bluetooth Manager.
David Tong.

I forgot to say in my original posting that the problem still exists in the current version of Toshiba Bluetooth Stack that I downloaded on 6th July from the Bluetooth page.
R2D2, your 'recommendation' would be useful if the site showed in detail what bugs have been fixed. I tried the new version because, although there was no mention of a fix for context menu issues, it does mention that "minor bug-fixes" have been made. I discovered the hard way that these fixes do not deal with the issue I described.
My experience with new Toshiba laptops over the past 15 years is that the update documentation seldom states clearly enough what has changed when new software versions appear. Yet such information could save users a lot of time.
Changing the Bluetooth stack from Microsoft to Toshiba and back is not a five-minute task.
But it seems that the MS Bluettooth stack works with Power Drawers
David Tong.

Install and configuring JDBC Driver in SAP Java stack

Hi Experts,
We are fetching data from GRC to BIW, for this we are using UD Connect in biw.
For this we need to configure and installed the JDBC Connectors.
Please suggest how to go about this.
Thanks,
Vijay

Hi
Check this SAP Notes
1347514 - How to setup and configure the webi/deski JDBC connection for the Microsoft SQL Server 2005 and Oracle 9i&10g Database
1602614 - How To Install And Configure Microsoft SQL JDBC Drivers
831162 - FAQ: XI 3.0 / PI 7.0 / PI 7.1 / PI 7.3 JDBC Adapter
Check the SCN blog
Michal's PI tips: JDBC/JMS driver deployment - now more forceMode=true
Configuring the JDBC Adapter - Advanced Adapter Engine - SAP Library
Regards
Ram

How to use a bluetooth dongle instead of built-in BT?

Just got an "Ultra Long Range Industrial" bluetooth dongle (BTD Bluetooth Dongle BT-6610). I want to use it instead of the built-in bluetooth because it has a much longer range.
How do I disable the built in bluetooth and enable the BT-6610?
The dongle shows up:
USB Bus:
Host Controller Location:          Built-in USB
Host Controller Driver:          AppleUSBOHCI
PCI Device ID:          0x0aa7
PCI Revision ID:          0x00b1
PCI Vendor ID:          0x10de
Bus Number:          0x06
Bolutek BTD-6610:
Product ID:          0x0001
Vendor ID:          0x0a12 (Cambridge Silicon Radio Ltd.)
Version:          59.41
Speed:          Up to 12 Mb/sec
Manufacturer:          Bolutek Technology Co.,Ltd.
Location ID:          0x06200000
Current Available (mA):          500
Current Required (mA):          200
BRCM2046 Hub:
Product ID:          0x4500
Vendor ID:          0x0a5c (Broadcom Corp.)
Version:           1.00
Speed:          Up to 12 Mb/sec
Manufacturer:          Apple Inc.
Location ID:          0x06100000
Current Available (mA):          500
Current Required (mA):          0
Bluetooth USB Host Controller:
Product ID:          0x8217
Vendor ID:          0x05ac (Apple Inc.)
Version:           1.80
Serial Number:          xxxxxxxxx
Speed:          Up to 12 Mb/sec
Manufacturer:          Apple Inc.
Location ID:          0x06110000
Current Available (mA):          500
Current Required (mA):          0
Here are my bluetooth setting:
Apple Bluetooth Software Version:          2.4.0f1
Hardware Settings:
Address:          xx-xx-xx-xx-xx-xx
Manufacturer:          Cambridge Silicon Radio
Name:          billbarnes
Firmware Version:          5941
Bluetooth Power:          On
Discoverable:          No
Vendor ID:          0
Product ID:          0x1
HCI Version:          4 (0x4)
HCI Revision:          5941 (0x1735)
LMP Version:          4 (0x4)
LMP Subversion:          5941 (0x1735)
Device Type (Major):          Computer
Device Type (Complete):          Macintosh Portable
Composite Class Of Device:          3670284 (0x38010c)
Device Class (Major):          1 (0x1)
Device Class (Minor):          3 (0x3)
Service Class:          448 (0x1c0)
Requires Authentication:          No
Services:
Bluetooth File Transfer:
Folder other devices can browse:          ~/Public
Requires Authentication:          Yes
State:          Enabled
Bluetooth File Exchange:
Folder for accepted items:          ~/Downloads
Requires Authentication:          Yes
When other items are accepted:          Ask
When PIM items are accepted:          Ask
When receiving items:          Prompt for each file
State:          Enabled
Devices (Paired, Favorites, etc)
Manufacturer:          Cambridge Silicon Radio (0x3, 0x10db)
Incoming Serial Ports:
Serial Port 1:
Name:          Bluetooth-PDA-Sync
RFCOMM Channel:          3
Requires Authentication:          No
Outgoing Serial Ports:
Serial Port 1:
Address:
Name:          Bluetooth-Modem
RFCOMM Channel:          0
Requires Authentication:          No

Hi X42:
Your last paragraph intrigued me as I had the same impression:
I thought unlicensed BT devices were legally limited by the FCC to about 30 feet (3 meters)
Actually, 30 feet is 10 meters.
Anyway, I researched and found this as part of a Wikipedia item:
Bluetooth is a standard wire-replacement communications protocol primarily designed for low power consumption, with a short range (power-class-dependent, but effective ranges vary in practice; see table below) based on low-cost transceiver microchips in each device.[7] Because the devices use a radio (broadcast) communications system, they do not have to be in visual line of sight of each other, however a quasi optical wireless path must be viable.[2]
Class
Maximum Permitted Power
Range
(approximate)
mW
dBm
Class 1
100
20
~100 meters
Class 2
2.5
4
~10 meters
Class 3
1
0
~5 meter
The effective range varies due to propagation conditions, material coverage, production sample variations, antenna configurations and battery conditions. In most cases the effective range of class 2 devices is extended if they connect to a class 1 transceiver, compared to a pure class 2 network. This is accomplished by the higher sensitivity and transmission power of Class 1 devices.[8]
Apparently there are BT devices that will transmit about 300 feet. I did look at the FCC site, but quickly became confused in the technbabble.
Barry

Problem with Usb Bluetooth dongle (Cambridge Silicon Radio Ltd.) on 10.5.8

Hello,
I tried until two day to configure a usb bluetooth dongle than I buy on ebay. This dongle work on my macbook osx 10.6 in System Profiler than y see this and tried many times to modifed the IOBluetoothfamily.kext
Can you help me?
Bluetooth HCI:
Product ID: 0x0001
Vendor ID: 0x0a12 (Cambridge Silicon Radio Ltd.)
Version: 19.15
Speed: Up to 12 Mb/sec
Location ID: 0x4b430000
Current Available (mA): 100
Current Required (mA): Unknown (Device has not been configured)

No configuration or modification of system files is required. If the USB Bluetooth dongle is Mac compatible, just plug it in and open the Bluetooth system preferences pane.
Not all USB Bluetooth dongles are fully Mac compatible.

Bluetooth dongle D-Link DBT-120 isn't recognized

Hello
I have a problem with a D-Link DBT-120 bluetooth-dongle.
Linux seems to recognize it, but it does not appear as bluetooth device. The device works on another linuxsystem.
lsusb:
Bus 002 Device 006: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
/var/log/messages.log beim einstecken des Sticks:
Jul 5 11:23:00 pcflo usb 2-1: new full speed USB device using ohci_hcd and address 6
Jul 5 11:23:00 pcflo usb 2-1: configuration #1 chosen from 1 choice
/etc/conf.d/bluetooth:
# Run the hcid daemon (default: true)
DAEMON_ENABLE="true"
# Run the bluetooth HID daemon (default: false)
HIDD_ENABLE="true"
hcitool dev:
Devices:
hciconfig
hci0: Type: USB
BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
DOWN
RX bytes:0 acl:0 sco:0 events:0 errors:0
TX bytes:0 acl:0 sco:0 commands:0 errors:0
Then: hciconfig hci0 up
->
hci0: Type: USB
BD Address: 00:0F:3D:48:F2:0B ACL MTU: 192:8 SCO MTU: 64:8
UP RUNNING
RX bytes:348 acl:0 sco:0 events:11 errors:0
TX bytes:35 acl:0 sco:0 commands:10 errors:0
hcitool dev
Devices:
hci0 00:0F:3D:48:F2:0B
But it still is not recognized by bluetooth-applet. What should it do, to change this?
On my other linuxsystem I don't need to enter anything. Just put the dongle in and bluetooth works fine.
I would be glad, if someone could help me.

It works excellent with Fedora 9 (same pc).
bash-3.2# /etc/rc.d/hcid start
bash: /etc/rc.d/hcid: Datei oder Verzeichnis nicht gefunden
bash-3.2# /etc/rc.d/hidd start
bash: /etc/rc.d/hidd: Datei oder Verzeichnis nicht gefunden
bash-3.2# locate hcid
/etc/bluetooth/hcid.conf
/usr/sbin/hcid
/usr/share/man/man5/hcid.conf.5.gz
/usr/share/man/man8/hcid.8.gz
/usr/src/linux-2.6.25-ARCH/include/config/bt/hcidtl1.h
/var/lib/pacman/sync/community/bluez-hcidump-1.41-1
/var/lib/pacman/sync/community/bluez-hcidump-1.41-1/depends
/var/lib/pacman/sync/community/bluez-hcidump-1.41-1/desc
Is there missing a package?

Need Vista driver for Bluetooth dongle model: TechBlue1

Hi,
I recently got given a Technika Bluetooth dongle, model: TechBlue1 and it isn't supported by Vista.
Is there any updates or drivers that will allow this?

{color:#800000}*The Technika TechBlue 1 dongle uses a TOSHIBA Bluetooth stack. It will only partially install under Vista and there is an incompatibility warning box. I have been unable to find the Bluetooth stack version number. Is there a patch or fix or Vista driver available, please Toshiba? This dongle is sold by TESCO, one of the biggest UK supermarkets and there must be a large number of these dongles in circulation.*
{color}

Improve Auto-Stack and Process Collections with user settings

I have read through all of the Bridge request discussions, and encountered a few comments on the stacking process but nothing to explain my critique and feature request. My apologies for any redundancy.
Bridge CS4 includes two features that would (virtually) streamline my entire photo-organization workflow. Brilliant! Except that they offer zero configuration and my default scenario is very different from Adobe's, so these two would-be-wonderful features are pretty much useless to me, and to anybody else who doesn't happen to shoot in the way the presets are configured.
The first feature is to automatically group images into stacks, based on their similarity, exposure settings, and timestamps. Unfortunately Bridge considers no minimum or maximum amount of photos per stack, and has a fixed timestamp window of 18 seconds. I shoot everything in three-exposure bursts and sometimes multiple shots in less than 18 seconds, so being able to say "process collections in 3-item stacks only" would be absolutely perfect. For other people, being able to limit the timestamp range or other min/max exposure options would work great.
The second feature, which could save me hours every week but is equally useless, is to automatically process collections in Photoshop. My biggest ire about this function is that it completely ignores stacks that I have manually created AND stacks that were previously created using the auto-stack feature. Every time this function is run, it re-runs the auto-stack process from scratch and then delivers the collections to Photoshop. Not only is this made useless by the previously mentioned inflexibility of the auto-stack process, but even if auto-stack worked perfectly, this would waste time by doing the entire thing again and denying the user the option to review the stacks before committing to the Photoshop processing. The process collections feature would also be much improved if the option were given to process ONLY panoramas or HDR photos, or auto-detect. I have never shot a panorama in my life and I'm sure plenty of people have never shot HDR, but Photoshop isn't capable of knowing our intentions and there's no reason why we shouldn't be able to instruct it.

Agree. It is an interesting capability that falls short of being really useful. I feel like an ingrate to complain, but ...
I'd also like to see the capability to specify something than "Auto" for the panorama option. My experience is that most of my panos work best with "Cylindrical + Geometric Correction".
My experience is that once you get past 5+ images in a pano, it becomes very tedious ... and then 20+ images in rows is painful. Unlike a single image that you can quickly evaluate, with panos I find I need to make the pano to tell if it going to turn out. I have been generating smaller 1800x1200 or 1200x1800 files to speed up the evaluation process, but it is still very manual and tedious.
The Auto-Stack generates a AutoCollectionCache.xml, but I haven't found it workable to edit this. I'd like to be able to modify it to "force" my knowledge of what is in a group. It seems to check the time-stamp, and re-do the Auto-Stack, thus ignoring my changes. Sigh.

Satellite C660-108 does not boot if USB Bluetooth dongle connected

Hiya,
I hope you would help me.
I am having an issue with my bluetooth dongle and satellite c660-108.
It works all perfectly. It connects devices via bluetooth and I can do everything I want.
But then when I am shutting down laptop and turning on again it won't go if the bluetooth dongle is still in the usb socket.
I see Toshiba screen and then it hangs with black screen and blinking cursor in top left corner.
I have to turn it off, take out the bluetooth dongle and then turn it on again.
And then windows starts. After that I have to put in bluetooth dongle again if I want to work with it.
It is not a huge issue but it is a bit annoying when I have to take out the bluetooth and put it back again to get the windows started.
I am currently running under win 8.1 but had it already with win 8.
Anybody any ideas??

>I see Toshiba screen and then it hangs with black screen and blinking cursor in top left corner.
Mostly the blinking cursor appears because the notebook cannot find an bootable device.
It looks like the unit cannot switch to the HDD while the USB dongle is connected.
I would recommend you checking the booting order in the BIOS.
Set the HDD at the first place and the USB as last possible booting device.
Save the changes and check if it helps.

How can I tell whether my Mac Pro is using the bluetooth dongle or not?

I got myself a bluetooth dongle to get around the terrible internal BT signal. When it's in use, it alleviates all my troubles and I can actually stroll halfway down the hall and still type accurately.
However, it seems that every time I reboot, it must stop using the dongle and use the internal, because I then get the terrible signal of the internal antenna. The only way to convince my computer to use the dongle, is to unplug and plug it back in. Then I have to delete all my bluetooth devices and pair them again!
So yes, I am seeking a two-part solution.
Firstly, I'd like to know if there's anywhere in System Profiler, BT Preferences, Terminal, etc that will just inform me of WHICH bluetooth my computer is using.
Secondly, I'd ideally want to set it to default to the dongle. If this isn't possible, at least the first part would let me know when I need to arduously re-do my settings.
Thank you very, very much. Usually this isn't that big an issue, as I only rarely need to move my peripherals off my desk, but I got a Magic Mouse earlier this week and its extremely clear it doesn't have as strong an antenna or whatever as the Mighty Mouse, and it starts going erratic if I move it so much as a foot from the Mac Pro tower.

I have the same problem and I cannot find any way to turn off the internal bluetooth without killing all bluetooth including the dongle. If someone has a way to turn off the internal bluetooth I want to see it.
Thanks

PI 7.1(dual stack) and PI 7.31(Single stack) -

Friends,
I have a proxy to proxy scenario - Proxy --> PI --> Proxy
We have two servers PI 7.1(dual stack) and PI 7.31(Single stack)
i did the development in ESR and my ESR is pointing to PI 7.1, when i execute the scenario i receive one error message "receiver could not be determined", i ensured that all my input is correct, still i get the same error message.
the expectation is my scenario should point to PI 7.31, Can some one help me where and what settings i need to make in-order to make it work.
Please Note: All my data is correct and i read some scn forums wherein they asked to refresh the cache , i have refreshed the cache also still the problem persists.
Thanks in advance!

Iñaki Vila
Communication component in ID is the same as sender side.
could you share your sender configuration?
Did you mean Tcode - SXMB_ADM and under that Sender/Receiver configuration
Krupa Rao Atluri
In ID steps are correctly defined.
I spoke to my colleague he hinted that at RUN TIME we want to point to PI7.31, he mentioned config change needed in SXMB_ADM
any further inputs from any one could be useful.

Errror in RFC connection between SCM ABAP stack and JAVA Stack

Hi All
we have installed SCM Abap stack and SCM java stack on same system within single database.when i create rfc connection AI_RUNTIME_JCOSERVER from SCM Java stack to SCM Abap Stack its working fine,but when i am configuring same from SCM Abap to SCM Java using SM59 its giving error.
Error Details     Error when opening an RFC connection
Error Details     ERROR: failed to open file G:\usr\sap\SCD\DVEBMGS00\data\sideinfo.DAT
Error Details     LOCATION: SAP-Gateway on host OPS20SCD1.Octal.pet / sapgw00
Error Details     CALL: fopen
Error Details     COMPONENT: SAP-GW-LIB (ReadSideInfo)
Error Details     COUNTER: 1854
Error Details     ERROR NUMBER: 2
Error Details     ERROR TEXT: ENOENT: No such file or directory OR: The system cannot find the fi*
Error Details     MODULE: gwxxside.c
Error Details     LINE: 274
Error Details     RETURN CODE: 451
Error Details     SUBRC: 0
Error Details     RELEASE: 701
Is it compulsory to create RFC connection between abap and java installed on the same system.
plese suggest.
Regards

to configure acceptance of the ABAP (integrated ITS / WebGUI) saplogonticket on the java stack, just log into the java stack (http://FQDN:50xxx/nwa) and select configuration THe last item in the list is Trusted System... click.
on the ensuing page, click on the add trusted system button --> by querying trusted sytem.
Enter the required data on the page:
system type: ABAP
host name: FQDN
System Nr: your instance number
client (of the productive client)
and a username and pw with superuser priveliges in the system (SAP_ALL/SAP_NEW, etc).
the click next
On the final screen, click finish.
You have now SSO setup between the ABAP and Java stacks. To configure SSO to accept java saplogontickets on ABAP see:
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/2b0310d6-0801-0010-3185-b2371a280372
This should resolve your question.

PI 7.31 Dual Stack SSL configuration

HI Gurus,
I have a quick query, I am configuring SSL on my PI 7.31 systems.
I have checked all the standard guides and forums but I have one doubt.
Q1 - Is it necessary to configure SSL both in ABAP and JAVA side ?
Q2 - If I just configure SSL in STRUSTSSO2 in ABAP , will it be more than enough ?
Q3 - In what cases do we need to configure SSL in JAVA side ? And does configuring SSL in JAVA mandatory require sapcryptolib files ?
Please share your views.
Cheers, SG

I want to understand is it necessary to configure SSL in both ABAP and JAVA in case of dual stack PI ?
>>> Please refer to Huseyin's comments in the below thread..
PI 7.3 Dual Stack SSL configuration
In what cases do we use JAVA SSL in Dual stack system ?
>>> AFAIK - when you use http_aae adapter/soap with https then you should configure the SSL on java stack.

Re@lted t0 bluetooth dongle, stack and configuration.. .......

Similar Messages

Maybe you are looking for