Re: No connection to SLM2008

Hi.
I've just bought a Linksys SLM2008, new, boxed and shrink wrapped from somebody, and it is 'brain dead', just as you all have - have the green 'Power' LED only.  The guy won't have it back as he says it was sold as new.  I think the IOS is not booting for some reason, but the unit gets very hot if left on for and hour or so.
As I'm an electronics engineer, (Radio, TV and self-build computers in the 70's and 80's) and more recently, Technical Projects Engineer for Compuatacenter, I want to take it apart without damage to have a look at the internals.  Anybody have instructions for this?
I notice Linksys wall plug power supplies fail - bulging capacitors on inspection.  Cheaper to bin it and buy a 2A unit from Hong Kong for £8 all in.  I used to install big Cisco Catalyst 6500 L3 switches, and we had a lot of PSU failures early on.
I'll let you know if I get Linksys to replace it first.

In my opinion, I believe the switch is indeed has some problems. This switch I think has a reset button. Try to press the reset button for 30 sec. then power cycle the unit. Connect a PC to one of the LAN ports. You should be getting a light in the port when the pc is connected. If not you should be able to replace the unit especially that you just bought the unit. If the store won’t accept it, I think you can replace it to Linksys directly or this case Cisco since they are now handling these devices. I suggest try contacting CISCO tech support and seek their opinion about it.

Similar Messages

  • No connection to SLM2008

    I have 2 SLM2008 that were configured a while back and left in a shelf to be used at a later time. Now that the time has come I am trying to connect them but any computer plugged on them is not recognized. (No lights on the switch). Plugging the computer on any other switch works.
    A reset to factory default doesn't even seem to work to reset all the settings. I would like to do a firmware upgrade on the units to see if it works but not being able to connect to them doesn't help me.
    Does anyone ever seen this problem ? or I have 2 defective units...
    Thanks

    Hi,
    I have the same problem as describe here. My switch (slm2008) has worked smoothly during more than 8 month. Always up and running without power off. But suddunly this week he is no more working. I haven't done any configuration changes this long time....
    I tried to power it off and on again but it is not working again. After that i tried a reset but not working better.
    And the end i tried a factory reset but still not working.
    Now i'm not being able to show the config web page anymore which must be now at address 192.168.1.254.
    Please could you provide some advise to test if the switch is broken....
    I tried the following to hit the config page but it doesn't worked:
    Routeur config: network ip : 192.168.1.100
    Mask given when static ip : 255.255.255.0
    -connect the switch to the routeur, my pc to the routeur (with dhcp, enable on the routeur) and try to hit the config page. Doesn't work.
    -connect the switch to the routeur, my pc to the routeur (with static ip) -> doesn't work. -connect the pc to the switch with static ip and gateway same has switch ip (192.168.1.254) -> doesn't work
    -connect the pc to the switch with dhcp ip -> doesn't work.
    Please could anyone provide the right connecting mode with ip for the devices ( pc and routeur etc) to hit the default config page to see if my switch is broken (192.168.1.254)
    Thx in advance...
    Message Edited by Fusfighter on 09-13-2008 05:13 AM
    Message Edited by Fusfighter on 09-13-2008 05:14 AM

  • SLM2008 to SG200-08 VLAN

    Hi,
    I have the following setup:
    Service Provider connected to SLM2008 port 2
    SLM2008 connected to SG300-20 using LAG2
    SG300-20 connected to SG200-08 using LAG1
    SG200-08 port 1 connected to PC
    I have configured VLAN 4 to isolate this (port-to-port)​ traffic from the rest of the network, however I can't obtain an IP address from the SP.
    SLM2008 : port 2 PVID 4 all frame types accepted, VLAN ID 4 assigned to port 2 and LAG 2 (consisting of port 5&6)
    on the SG300-20, the Port VLAN Membership Table shows LAG1 & 2 with 1UP, 4T (so supposed to transport VLANs 1 & 4, 1 being the default)
    SG200-08 shows Port VLAN Membership Table port 1 in access mode with PVID 4 and operational VLAN membership 4U. I can't put it to 4T except in generic mode, but this doesn't work either.
    What am I missing here ?
    Any input/feedback would be highly appreciated.
    Christophe

    Hi chrebert,
    Thanks for your answer. You're right in concluding the VLAN 1 is my default VLAN. The problem is that the switch should contact my DHCP server over VLAN 1 and since the traffic on port 1 is not tagged, the traffic DHCP request will never reach my DHCP server. As a consequence, the switch always ends up with its factory default IP address (192.168.1.254) instead of the IP address assigned by the DHCP server. And yes, that's a problem
    So to summarize, when I configure tagged access for VLAN 1 on port 1 and write this to the startup config, it is indeed present in the startup config afterwards. However, the switch ignores this upon reboot, causing VLAN 1 on port 1 to feature untagged access.
    By the way, I completely set up the switch from scratch after restoring the config to factory defaults. It would be great if you could try to reproduce the issue and hopefully come with a fix. In case you need more information, please don't hesitate to contact me.

  • Connecting a 2nd laptop to wireless router

    Hi, Everyone - I have my Mac desktop connected to a WRT54GS wireless router, as well as a Dell laptop connected. All is working fine up till now...
    Now I'm trying to connect a 2nd Dell laptop but can't get it to connect! It detects the network, but when you click on "connect" it says "acquiring connection" but then it gives an error saying something about limited access. It is a secured network, BTW.
    How can I get this 2nd computer connected?
    I also noticed something called "Default Tx Key" which is set to 1 - this key is what the 1st laptop is using. How do I get the 2nd one to be available - if I click on #2 for the default key, it disables #1.
    What do I need to do?!! Thanks so much!

    use the same key for ALL wireless devices, it is a shared key. so the key for #1 is used on ALL of the laptops.
    Regards Simon
    NAS: TS-459 Pro - 3.6.1 Build0302T - 4 x 1TB Samsung HD103SJ : EXT4 - APC ES 700VA UPS
    QPKG: WordPress 3.4, TwonkyMedia 6.0.39 QPKG - Zenphoto1.4.2.1 [7802] - phpMyAdmin v3.3.10
    Network: Netgear DG834G V4.01.40 - DGTeam Rev. 0849 -> Cisco RV220W 1.0.4.13, Cisco SLM2008, Dlink DSM-520, Xbox360

  • Linksys WRT54G v5 - Connection issues

    Good evening,
    I picked up a new WRT54G (v5) the other day to replace an old BEFW11 router, and so far have been far less than impressed.  I have one computer on the wired connection, and one on wireless.  It seems, though, that if the wireless system is running any P2P software (Limewire, in this case), or anything else which creates a large number of simultaneous connections (BitTorrent for d/ling CD images, for instance), the router simply dies.  Although any existing TCP connections are fine (e.g. MSN Messenger switchboard connections, though not _new_ conversations), it is virtually impossible to generate any new TCP connections.  They appear to connect immediately, and then disconnect less than a second later.  This occurs for HTTP, SSH, Telnet, IMAP, and SMTP connections, so far as I've tried.
    A hard reset of the router seems to be the only thing that helps. 
    I ran into similar issues with the BEFW11, and ended up using it only as an access point, and relying on an old D-Link DI-704P to take care of NAT -- and this worked fine.  But in this case, I want to take the DI-704 with me when I move, not leave it here ... and so I would really prefer if the Linksys could, uh, do what it's supposed to in the first place. 
    I tried upgrading the firmware to v1.00.9, but after sitting there for a few minutes I ended up with a "this page cannot be displayed" error from I E.  I'm going to give it another shot, but am a little hesitant to reboot the router at this point because I have no idea if it will be toast at that point or not. 
    EDIT: Now upgraded to v1.00.9.  Apparently this doesn't work over HTTPS, but it worked fine via HTTP itself.  We'll see if this has made a difference ...
    I see some similar reports from other people.  Any suggestions?
    Message Edited by tibbbsa on 07-08-2006 09:00 PM

    tibbbsa wrote:
    I see some similar reports from other people. Any suggestions?
    yeah use a WRT54GL instead. my website is unindated with wrt54g/GS v5 and v6 router problems. how linksys has been able to ignore this problem is beyond me. the WRT54GL is by far the better router. (linux based)
    Regards Simon
    NAS: TS-459 Pro - 3.6.1 Build0302T - 4 x 1TB Samsung HD103SJ : EXT4 - APC ES 700VA UPS
    QPKG: WordPress 3.4, TwonkyMedia 6.0.39 QPKG - Zenphoto1.4.2.1 [7802] - phpMyAdmin v3.3.10
    Network: Netgear DG834G V4.01.40 - DGTeam Rev. 0849 -> Cisco RV220W 1.0.4.13, Cisco SLM2008, Dlink DSM-520, Xbox360

  • Question about SLM2008

    I got three domain on the same network. Trying to set up a vlan to split all the computers to respective domain. This is my setup i got 5 static IPS. The respective IP runs to a wireless router which then runs to a server and to the SLM2008 router. Now my question is i got all the computers in my office running to one Port in the back of the SLM2008. I want 3 Vlans, one for each company. I have had the Packets tagged but it doesnt seem to work. Any help would be great. Thanks in Advance.

    Sorry about that this is how it is set up I have a modem that supports multiple static IPS. The Modem is a Motorola 3347. The Modem Conects to three seperate routers all of them are Linksys WRV54G. The first Router connects to port two of the SLM2008 and also \ connects to a server. The second router connects to port three of the SLM2008 and to another server. The third router connects to port four and connects to yet another server. Port 5 is then connected to to the wall witch is then distributed to the other computers through out the office. Right now I the Vlans set up as the following. Vlan 1 ports are port 5 and port 2. Vlan 2 port 5 and port 3. Vlan 3 port 5 and port 4. On the computers i have downloaded the vlan drivers for my ethernet adapter and connected them to the repective vlans(mainly vlan1). But non of the computers can see the server on the repective vlan. This is a pretty complicated setup but any help would be appreciated.

  • WRT54GS Connects to the Internet Not Admin Page

    I am able to connect to the internet with the WRT54GS and was able to access the admin page, but now all I get is "Page Can Not Be Displayed". I powered everything off and than turned on the broadband DSL modem, the router and than the PC but still can't get the admin page to load. I am using Windows XP. Can someone please help. Thanks in advance

    What is the Ip of your DSL modem? is this the same as your WRT54GS perhaps?
    have you setup a proxy cache in your web browsers LAn settings perhaps?
    any antivirus/web scanning or firewall utils that are blocking it?
    Regards Simon
    NAS: TS-459 Pro - 3.6.1 Build0302T - 4 x 1TB Samsung HD103SJ : EXT4 - APC ES 700VA UPS
    QPKG: WordPress 3.4, TwonkyMedia 6.0.39 QPKG - Zenphoto1.4.2.1 [7802] - phpMyAdmin v3.3.10
    Network: Netgear DG834G V4.01.40 - DGTeam Rev. 0849 -> Cisco RV220W 1.0.4.13, Cisco SLM2008, Dlink DSM-520, Xbox360

  • SSID change & odd connection timeouts

    Hello,
    We are in the process of changing our ssid's and re-subnetting our networks.  We have 1142's, 1131's and a 5508 controller.  I have everything working, but I have noticed that sometimes the clients (all windows xp sp3) will take a long time to connect to the ssid's, both the old and new ones.  It almost looks like it's taking a long time to get the ip address from the dhcp server (which is the switch where the access point is connected too).
    I'm tring to find out more information about some of the WLAN settings and I was wondering if anyone knew if "Learn Client IP Address" under advanced H-REAP settings in the WLAN configuration would be the cause of the slow or timing out connections?
    Currently in the advanced tab of the WLAN configuration I have the following enabled:
    Coverage Hole Detection
    Aironet IE
    Client Exclusion - 60 Seconds
    H-Reap
    Learn Client Ip Address
    Any ideas?

    1. WEP is hackable.
    2. leaving the SSID to linksys tells a hacker/wardriver to use "admin" as the default password!
    Change your SSID
    Change your admin password to something longer than 8 characters (with upper/lower case letters and numbers) if WEP has to be used then use the highest level of WEP encryption.
    The hacker has most likely now got all you MAC addresses if he has been on your router. i would now go out and buy a USB WPA stick that works with your Mac and use WPA encryption with more than 20 characters for the passkey.
    This story is a prime example of how to get hacked.
    Wireless Security - How secure is your Wireless Network?Message Edited by linksysinfo on 09-02-2006 11:29 PM
    Regards Simon
    NAS: TS-459 Pro - 3.6.1 Build0302T - 4 x 1TB Samsung HD103SJ : EXT4 - APC ES 700VA UPS
    QPKG: WordPress 3.4, TwonkyMedia 6.0.39 QPKG - Zenphoto1.4.2.1 [7802] - phpMyAdmin v3.3.10
    Network: Netgear DG834G V4.01.40 - DGTeam Rev. 0849 -> Cisco RV220W 1.0.4.13, Cisco SLM2008, Dlink DSM-520, Xbox360

  • SLM2008 VLAN

    Hi, VLAN newbie here!
    I need to setup a VLAN using a SLM2008 and connect it to our Fortigate Internet Firewall.  I'm doing this to segregate the SLM2008 traffic from the main network which is already connected to the firewall.  I have created VLAN #200 in the SLM2008.  I have read all the SLM2008 documentation and spent quite a lot of time on these forums but can't seem to get this working.
    Questions:
    1. The firewall is seen on the network as another multi-port hub, so does this mean that the SLM2008 must be connected to it via a VLAN trunk link?
    2. On this forum someone said you must use Port 1 of the SLM2008 if you want to do trunking?  True?
    3. If #2 is correct, then how do you setup port 1 as a trunk?  There is no trunk option in the web gui.
    Thanks in advance!
    Marty

    I finally found the answer by discovering this page.  The Cisco documenation is incomplete
    on setting up the SLM2008 as a VLAN trunk.  Follows the steps given here:
    http://www.jarmanator.net/kb/slm2008vlan.htm
    Marty

  • Падение скорости SLM2008

    Здравствуйте, у меня 2 свитча  SLM2008
    Только на одном через несколько часов работы падает скорость, подключено 3 компьютера на скорости 1гбит и роутер на скорости 100мбит, скорость с 1гбита падает до 5мбит, при этом соединение показывает 1гбит. Помогает только перезагрузка свитча, потом снова через несколько часов такая же ситуация.
    Прошивка Current Firmware Version: 2.0.0.10
    Пробовал перепрошивать, сбрасывать на заводские установки, ничего не помогло.
    Подскажите пожалуйста как исправить?
    Вот тесты до и после перезагрузки свитча
    iperf -c 192.168.1.2
    Client connecting to 192.168.1.2, TCP port 5001
    TCP window size: 16.0 KByte (default)
    [  3] local 192.168.1.5 port 51197 connected with 192.168.1.2 port 5001
    [ ID] Interval       Transfer     Bandwidth
    [  3]  0.0-10.0 sec  70.4 MBytes  58.9 Mbits/sec
    [root@armtorrent ~]# iperf -c 192.168.1.2
    Client connecting to 192.168.1.2, TCP port 5001
    TCP window size: 16.0 KByte (default)
    [  3] local 192.168.1.5 port 50283 connected with 192.168.1.2 port 5001
    [ ID] Interval       Transfer     Bandwidth
    [  3]  0.0-10.0 sec   822 MBytes   689 Mbits/sec

    Hi
    After looking at the iperf data, it sure indicates a problem with traffic between the two switches or maybe within a switch.. 
    The exact cause of this traffic problem is undetermined at this stage, needs further analysis...
    Do we enable flow control, what is the autonegotiated speed of the ethernet port, what do the port statistics look like.  these are all questions that should be looked into.
    It would have been be interesting to see a wireshark capture going to IP host at 192.168.1.2 at times when throughput is low. and a capture when throughput was good.  These captures only need to be a few seconds in long.
    Might I suggest that you contact your local Small Business Support Center who can assist in hopefully identifying your issue.
    I have copied the worldwide support contact information URL below for your referenece.
    http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
    regards Dave

  • SLM2008 and SD2008 don't work together

    Has anyone trouble to get Linksys SLM2008 Managed and Linksys SD2008 Unmanaged to Work together? SD2008 LED Light is continously flashing at connected Port.

    Hi Erik,
    I am guessing this might be a new installation and still covered by phone support warranty..
    Please open a case with the Small Business Support center to determine the cause of the issue.
    http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
    regards Dave

  • Wired Connection Works, but Wireless won't connect

    I just got the Wireless-N Broadband Router and I have my Home computer connected to it through a LAN connection. And I have an internet connection. But on my Laptop the only thing that my WiFi connection picks up is HPsetup (Is this my Linksys Router?).. The Hpsetup has a very low connection by my Linksys Router. And the signal fades in and out.

    what Conection protocol does your Laptop use?
    PreN, 802.11g, 802.11b?
    Regards Simon
    NAS: TS-459 Pro - 3.6.1 Build0302T - 4 x 1TB Samsung HD103SJ : EXT4 - APC ES 700VA UPS
    QPKG: WordPress 3.4, TwonkyMedia 6.0.39 QPKG - Zenphoto1.4.2.1 [7802] - phpMyAdmin v3.3.10
    Network: Netgear DG834G V4.01.40 - DGTeam Rev. 0849 -> Cisco RV220W 1.0.4.13, Cisco SLM2008, Dlink DSM-520, Xbox360

  • WRT54GS Internet Connection Issues

    I have a new WRT54GS with factory firmware.  I am constantly losing internet connection which I then have to unplug and replug the router which fixes the issues.   Any ideas?  FYI...I tried to download the latest firmware (which I thihnk I did correctly) and it said "Installation Failed" numerous times.  Please help!

    what version of WRT54GS do you have? what version of Firmware is loaded on it at present?
    Regards Simon
    NAS: TS-459 Pro - 3.6.1 Build0302T - 4 x 1TB Samsung HD103SJ : EXT4 - APC ES 700VA UPS
    QPKG: WordPress 3.4, TwonkyMedia 6.0.39 QPKG - Zenphoto1.4.2.1 [7802] - phpMyAdmin v3.3.10
    Network: Netgear DG834G V4.01.40 - DGTeam Rev. 0849 -> Cisco RV220W 1.0.4.13, Cisco SLM2008, Dlink DSM-520, Xbox360

  • Hi, i am trying to open and view a report that comes from another server with different odbc connection

    hi, i am trying to open and view a report that comes from another server with different odbc connection
    i created a crystal report for a mysql database on my machine and everything works great
    but we have other reports that come from other machines with different odbc connection
    and this its not working when opens the report asks for credentials
    and i cannot use the remote ip for these reports that come from other machine
    question
    if i cannot connect to remote ip to open the report
    for each report i have to create a database the report database on my machine and then open the report ?
    or there is some other way to open the report ?
    i am using visual studio 2013 and mysql and
       <add key="MYSQLODBCDRIVER" value="{MySQL ODBC 5.3 UNICODE Driver}"/>
    thanks

    short
    i have a report that it was created on another server with a specific dsn
    now i am trying to open the report on my machine
    the database from the other server does not exist on my machine
    the server machine where the report was created the ip its not accessible
    question ?
    can i open the report on my machine or its impossible ?
    thanks

  • Connecting Audiovox TV (FPE3205) using Apple Mini-DVI to Video Adapter

    I can't figure out what I'm missing here. All the connections look right, but... well, it's possible that I just don't know what I'm supposed to do now. I restarted both devices, but still, nothing. Any ideas?

    You've posted in the iMac G3 CRT area. Are you asking this question about an iMac?
    David

Maybe you are looking for