Re: Oracle Solaris Cluster 3.3 using Oracle Solaris 09/10 on virtualbox

Dear All,
I am trying to build a solaris cluster 3.3 on virtualbox using Oracle Solaris 09/10. My host OS is Ubuntu 10.10. But, when i try to add the second node, it is not able to find the node1 says "unable to connect to node1". Can anyone help me build this cluster.
my laptop is hp probook 4420s and has i3 processor and 2gb ram, wherein i have assigned 750mb ram to both Oracle Solaris 09/10 OS. Moreover, the first node is successfully attached. Both the virtual machines can ssh succesfully and link based ipmp is setup on both the virtual machines. Please help me regarding this as i am new to clustering.

As Nik said, this could be a problem with the setup of the private interconnects. This could also be caused by the fact that the necessary ports on the nodes are closed - due to secure by default.
There is an old blog entry on blogs.sun.com by Thorsten Frueauf that explains how to open the ports and/or start the necessary services. I think it is also documented now as part of the normal installation manuals.

Similar Messages

Prerequisites : 2-node Solaris Cluster 4.1 using VirtualBox.

Hi,
I am going to try building a 2-node Solaris Cluster 4.1 using VirtualBox. I have downloaded Solaris 11.1 ISO. Can someone please help me with the right configuration for the 2 nodes/guests, particularly the NICs and shared storage?
Thanks,
Shankar

https://blogs.oracle.com/TF/entry/new_white_paper_practicing_solaris
it's a bit dated but should still get you there.

Solaris Cluster 3.2 with Oracle 11i R2 oracle agent installation question

Hi all!
I'm new in clustering and trying to build a two-node cluster in my lab. At the moment i've successfully installed cluster software and oracle on the nodes and now i'm trying to integrate cluster with oracle DB. Unfortunately, i couldn't find the documentation about this task. Can anyone give me an URL, where to look? By the way: i tried to find something here: http://docs.sun.com/app/docs/doc/820-7360/fxjbo?a=view but found info only about Oracle RAC and nothing else, but i'm trying to build cluster without RAC - just only with solaris cluster.

Hi,
You might run into trouble with 11gR2 right now. You need to wait until the nxt patch for th eHA Oracle agent is avialble, or use 11gR1 at the moment.
Sorry for the bad news.
Detlef

How can i start oracle databases? i am using Oracle 8.1.6 for linux.

when i run dbstart,it gives me following message:
Database "ora4cweb" warm started.
but when i use sqlplus,it says:
ORA-01034: ORACLE not available
i made a mistake ,i shutdown my linux before i shutdown oracle databases,how can i start oracle databases now?thanks in advance.

try it without the scripts...
login to linux as oracle
start server manager
svrmgrl
connect internal
startup
select sysdate from dual;if that works
exitcheck listener
lsnrctl
statif nothing running type
start
exitnull

Connecting to Oracle 8.0.3 server using Oracle 10.1.0 client

I was wondering if it was possible to connect to a oracle 8.0 or oracle 8.1 server using oracle 10.1 client.
I have tried connecting to oracle 8.0.3 and it gives me an error saying "connections to this server are no longer supported."

If updating your Oracle Database isn't an option, then you can have 2 different clients installed (in different "Oracle Homes" (or directories), and use the selecthome.bat file to switch between your installed clients.
For example, before connecting to 8i, you'd run:
C:\Oracle\Client1_8i\bin\selecthome.bat
or this to use your Oracle 10g client:
C:\Oracle\Client2_10g\bin\selecthome.bat

Oracle EBS R12 - DR setup using Oracle Data Guard

Hi,
Our customer has implemented Oracle EBS R12 (12.0.6) on a Two Node RAC on HP-UX env. The application Tier also has Two Nodes(Admin Tier and Web Tier).
Oracle Clusterware - OCR and Vote Disk are on Raw Devices and the EBS database is on ASM.
Customer wants to implement a DR solution with Oracle Data Guard with only 2 servers - 1 for the Database Tier and 1 for the Application Tier on the DR Site.
I would like to know if this could be done by following note: 452056.1? I would also like to know if there are other useful docs.
Thanks.
Thiru

Hi,
Customer escalated this issue to Oracle and they came up with this reply:
They can implement Disaster recovery solution from RAC to NON RAC using Solution A which use RMAN utilities for backup and recovery.
While now AMP Application Management Pack gives the capablitiy to build non RAC from RAC Envioment, In future AMP will be capable also to support cloning of DB with Data Guard.
Details
Solution A - Using RMAN:
For Release 12 customers, you can clone from a RAC to RAC (like to like) or RAC to non-RAC. This is using RMAN scripts to take a copy of the db when it’s in archive mode. if you’re leveraging any disaster recovery tools like data guard, the above solution should work fine…perhaps some fine tuning to the procedures
Solution B - Using AMP in the future release
For Release 11i , Release 12.x customers, AMP would be offering a new cloning solution that wouldn’t have dependency on Rapid Clone. This solution leverages the strengths of EM Grid Control in provisioning or cloning targets such as databases. This would be an advance solution that would support:
o A full-fledged scale down cloning
o Cloning of EBS deployed on Shared File System
o Hot and Cold mode cloning
o Quantifiable reduction in clone time for the entire EBS system
This solution would be leveraging EM grid Control’s DB provisioning pack’s clone utilities, that are quite advanced and support cloning of DB with Data Guard.
The recommendation is to start trialing AMP version 3.0, making the purchase and implementing within the Enterprise. As we release the new version of AMP (release 3.0.1), Customer would be in a better position to quickly implement the latest features
Can anyone let me know if the solution A suggested will work.
Rgds,
Thiru

Oracle error ORA-00600 when using Oracle 10g and Sun One Web Server 6.1

I have a java application that was running under Solaris 8 and Oracle 9i. I am trying to get it up and running on a new server that is configured with Solaris 9 and Oracle 10g. Whenever the application tries to connect to the database it receives the following error: ORA-00600 [ttcgcshnd-1][0]. My research indicates that this is an internal Oracle error that represents a low level unexpected condition. I have looked through my configuration for the Web Server and I have not been able to determine the cause of this problem. My DBA tells me that we have the latest patch installed for Oracle! Has anyone encountered this problem before? Any help would be greatly appreciated!

If the problem is also present in a SWING app, i.e. outside the web server, then it is porbably something external to the webserver.
I think you should ensure that the driver and database are compatible with each other. It is very likely that you need a new jdbc driver for the new database.
download from here http://www.oracle.com/technology/software/tech/java/sqlj_jdbc/htdocs/jdbc101020.html
try the ojdbc14.jar

HOWTO: Create 2-node Solaris Cluster 4.1/Solaris 11.1(x64) using VirtualBox

I did this on VirtualBox 4.1 on Windows 7 and VirtualBox 4.2 on Linux.X64. Basic pre-requisites are : 40GB disk space, 8GB RAM, 64-bit guest capable VirtualBox.
Please read all the descriptive messages/prompts shown by 'scinstall' and 'clsetup' before answering.
0) Download from OTN
- Solaris 11.1 Live Media for x86(~966 MB)
- Complete Solaris 11.1 IPS Repository Image (total 7GB)
- Oracle Solaris Cluster 4.1 IPS Repository image (~73MB)
1) Run VirtualBox Console, create VM1 : 3GB RAM, 30GB HDD
2) The new VM1 has 1 NIC, add 2 more NICs (total 3). Setting the NIC to any type should be okay, 'VirtualBox Host Only Adapter' worked fine for me.
3) Start VM1, point the "Select start-up disk" to the Solaris 11.1 Live Media ISO.
4) Select "Oracle Solaris 11.1" in the GRUB menu. Select Keyboard layout and Language.
VM1 will boot and the Solaris 11.1 Live Desktop screen will appear.
5) Click <Install Oracle Solaris> from the desktop, supply necessary inputs.
Default Disk Discovery (iSCSI not needed) and Disk Selection are fine.
Disable the "Support Registration" connection info
6) The alternate user created during the install has root privileges (sudo). Set appropriate VM1 name
7) When the VM has to be rebooted after the installation is complete, make sure the Solaris 11.1 Live ISO is ejected or else the VM will again boot from the Live CD.
8) Repeat steps 1-6, create VM2 and install Solaris.
9) FTP(secure) the Solaris 11.1 Repository IPS and Solaris Cluster 4.1 IPS onto both the VMs e.g under /home/user1/
10) We need to setup both the packages: Solaris 11.1 Repository and Solaris Cluster 4.1
11) All commands now to be run as root
12) By default the 'solaris' repository is of type online (pkg.oracle.com), that needs to be updated to the local ISO we downloaded :-
+$ sudo sh+
+# lofiadm -a /home/user1/sol-11_1-repo-full.iso+
+//output : /dev/lofi/N+
+# mount -F hsfs /dev/lofi/N /mnt+
+# pkg set-publisher -G '*' -M '*' -g /mnt/repo solaris+
13) Setup the ha-cluster package :-
+# lofiadm -a /home/user1/osc-4_1-ga-repo-full.iso+
+//output : /dev/lofi/N+
+# mkdir /mnt2+
+# mount -f hsfs /dev/lofi/N /mnt2+
+# pkg set-publisher -g file:///mnt2/repo ha-cluster+
14) Verify both packages are fine :-
+# pkg publisher+
PUBLISHER                   TYPE     STATUS P LOCATION
solaris                     origin   online F file:///mnt/repo/
ha-cluster                  origin   online F file:///mnt2/repo/
15) Install the complete SC4.1 package by installing 'ha-cluster-full'
+# pkg install ha-cluster-full+
14) Repeat steps 12-15 on VM2.
15) Now both VMs have the OS and SC4.1 installed.
16) By default the 3 NICs are in the "Automatic" profile and have DHCP configured. We need to activate the Fixed profile and put the 3 NICs into it. Only 1 interface, the public interface, needs to be
configured. The other 2 are for the cluster interconnect and will be automatically configured by scinstall. Execute the following commands :-
+# netadm enable -p ncp defaultfixed+
+//verify+
+# netadm list -p ncp defaultfixed+
+#Configure the public-interface+
+#Verify none of the interfaces are listed, add all the 3+
+# ipadm show-if+
+# run dladm show-phys or dladm show-link to check interface names : must be net0/net1/net2+
+# ipadm create-ip net0+
+# ipadm create-ip net1+
+# ipadm create-ip net2+
+# ipadm show-if+
+//select proper IP and configure the public interface. I have used 192.168.56.171 & 172+
+# ipadm create-addr -T static -a 192.168.56.171/24 net0/publicip+
+#IP plumbed, restart+
+# ipadm down-addr -t net0/publicip+
+# ipadm up-addr -t net0/publicip+
+//Verify publicip is fine by pinging the host+
+# ping 192.168.56.1+
+//Verify, net0 should be up, net1/net2 should be down+
+# ipadm+
17) Repeat step 16 on VM2
18) Verify both VMs can ping each other using the public IP. Add entries to each other's /etc/hosts
Now we are ready to run scinstall and create/configure the 2-node cluster
19)
+# cd /usr/cluster/bin+
+# ./scinstall+
select 1) Create a new cluster ...
select 1) Create a new cluster
select 2) Custom in "Typical or Custom Mode"
Enter cluster name : mycluster1 (e.g)
Add the 2 nodes : solvm1 & solvm2 and press <ctrl-d>
Accept default "No" for <Do you need to use DES authentication>"
Accept default "Yes" for <Should this cluster use at least two private networks>
Enter "No" for <Does this two-node cluster use switches>
Select "1)net1" for "Select the first cluster transport adapter"
If there is warning of unexpected traffic on "net"1, ignore it
Enter "net1" when it asks corresponding adapter on "solvm2"
Select "2)net2" for "Select the second cluster transport adapter"
Enter "net2" when it asks corresponding adapter on "solvm2"
Select "Yes" for "Is it okay to accept the default network address"
Select "Yes" for "Is it okay to accept the default network netmask"Now the IP addresses 172.16.0.0 will be plumbed in the 2 private interfaces
Select "yes" for "Do you want to turn off global fencing"
(These are SATA serial disks, so no fencing)
Enter "Yes" for "Do you want to disable automatic quorum device selection"
(we will add quorum disks later)
Enter "Yes" for "Proceed with cluster creation"
Select "No" for "Interrupt cluster creation for cluster check errors"
The second node will be configured and 2nd node rebooted
The first node will be configured and rebootedAfter both nodes have rebooted, verify the cluster has been created and both nodes joined.
On both nodes :-
+# cd /usr/cluster/bin+
+# ./clnode status+
+//should show both nodes Online.+
At this point there are no quorum disks, so 1 of the node's will be designated quorum vote. That node VM has to be up for the other node to come up and cluster to be formed.
To check the current quorum status, run :-
+# ./clquorum show+
+//one of the nodes will have 1 vote and other 0(zero).+
20)
Now the cluster is in 'Installation Mode' and we need to add a quorum disk.
Shutdown both the nodes as we will be adding shared disks to both of them
21)
Create 2 VirtualBox HDDs (VDI Files) on the host, 1 for quorum and 1 for shared filesystem. I have used a size of 1 GB for each :-
*$ vboxmanage createhd --filename /scratch/myimages/sc41cluster/sdisk1.vdi --size 1024 --format VDI --variant Fixed*
*0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100%*
*Disk image created. UUID: 899147b9-d21f-4495-ad55-f9cf1ae46cc3*
*$ vboxmanage createhd --filename /scratch/myimages/sc41cluster/sdisk2.vdi --size 1024 --format VDI --variant Fixed*
*0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100%*
*Disk image created. UUID: 899147b9-d22f-4495-ad55-f9cf15346caf*
22)
Attach these disks to both the VMs as shared type
*$ vboxmanage storageattach solvm1 --storagectl "SATA" --port 1 --device 0 --type hdd --medium /scratch/myimages/sc41cluster/sdisk1.vdi --mtype shareable*
*$ vboxmanage storageattach solvm1 --storagectl "SATA" --port 2 --device 0 --type hdd --medium /scratch/myimages/sc41cluster/sdisk2.vdi --mtype shareable*
*$ vboxmanage storageattach solvm2 --storagectl "SATA" --port 1 --device 0 --type hdd --medium /scratch/myimages/sc41cluster/sdisk1.vdi --mtype shareable*
*$ vboxmanage storageattach solvm2 --storagectl "SATA" --port 2 --device 0 --type hdd --medium /scratch/myimages/sc41cluster/sdisk2.vdi --mtype shareable*
The disks are attached to SATA ports 1 & 2 of each VM. On my VirtualBox on Linux, the controller type is "SATA", whereas on Windows it is "SATA Controller".
The "--mtype shareable' parameter is important
23)
Mark both disks as shared :-
*$ vboxmanage modifyhd /scratch/myimages/sc41cluster/sdisk1.vdi --type shareable*
*$ vboxmanage modifyhd /scratch/myimages/sc41cluster/sdisk2.vdi --type shareable*
24) Start both VMs. We need to format the 2 shared disks
25) From VM1, run format. In my case, the 2 new shared disks show up as 'c7t1d0' and 'c7t2d0'.
+# format+
select disk 1 (c7t1d0)
[disk formated]
FORMAT MENU
fdisk
Type 'y' to accept default partition
partition
0
<enter>
<enter>
1
995mb
print
label
<yes>
quit
quit26) Repeat step 25) for the 2nd disk (c7t2d0)
27) Make sure the shared disks can be used for quorum :-
On VM1
+# ./cldevice refresh+
+# ./cldevice show+
On VM2
+# ./cldevice refresh+
+# ./cldevice show+
The shared disks should have the same DID (d2,d3,d4 etc). Note down the DID that you are going to use for quorum (e.g d2)
By default, global fencing is enabled for these disks. We need to turn it off for all disks as these are SATA disks :-
+# cldevice set -p default_fencing=nofencing-noscrub d1+
+# cldevice set -p default_fencing=nofencing-noscrub d2+
+# cldevice set -p default_fencing=nofencing-noscrub d3+
+# cldevice set -p default_fencing=nofencing-noscrub d4+
28) It is better to do one more reboot of both VMs, otherwise I got a error when adding the quorum disk
29) Run clsetup to add quorum disk and to complete cluster configuration :-
+# ./clsetup+
=== Initial Cluster Setup ===
Enter 'Yes' for "Do you want to continue"
Enter 'Yes' for "Do you want add any quorum devices"
Select '1) Directly Attached Shared Disk' for the type of device
Enter 'Yes' for "Is it okay to continue"
Enter 'd2' (or 'd3') for 'Which global device do you want to use'
Enter 'Yes' for "Is it okay to proceed with the update"
The command 'clquorum add d2' is run
Enter 'No' for "Do you want to add another quorum device"
Enter 'Yes' for "Is it okay to reset "installmode"?"Cluster initialization is complete.!!!
30) Run 'clquorum status' to confirm both nodes and the quorum disk have 1 vote each
31) Run other cluster commands to explore!
I will cover Data services and shared file system in another post. Basically the other shared disk
can be used to create a UFS filesystem and mount it on all nodes.

The Solaris Cluster 4.1 Installation and Concepts Guide are available at :-
http://docs.oracle.com/cd/E29086_01/index.html
Thanks.

Requesting Oracle Db Client 9i or 10g for Solaris

Dear friends
What is the name in "combo box" in metalink when i open an SR that identifies "Oracle Client for Solaris".
i dont know what it is. Please you could help me?
thanks
cesar.

I believe Oracle don't have CD that only have Oracle client for Solaris.
They only have client only CD for Windows. To install Oracle client for Solaris you need to use Oracle server CD/DVD, which usually come with a combo box with all kinds of other products as well.

Using Oracle Berkeley DB Java Edition RELEASE 3.2

Hi,
I am completely new to Oracle. I intend to use Oracle Berkeley DB Java Edition RELEASE 3.2., in conjunction with Java.
Can some one help me figure out what documentation I should use, and the learning path ?
Any suggestions would be greatly appreciated.
Thanks
Ravi Banthia
Kolkata

Please refer
http://www.oracle.com/technology/products/berkeley-db/je/index.html

Looking for some help with using Oracle stored procedures in vb2010

First off thank you to whoever lends me a hand with my problem. A little background first I am in a software development class and we are currently building our program using VB (I have no experience in this), and Oracle(currently in a Oracle class so I know how to use Oracle itself just not with VB).
I am using vb2010 express edition if that helps. Currently I have a stored procedure that takes a 4char "ID" that returns a position (ie, salesperson,manager ect). I want to use the position returned to determine what vb form is displayed (this is acting as a login as you dont want a salesperson accessing the accountants page for payroll ect).
Here is the code I have currently on the login page of my VB form
Imports Oracle.DataAccess.Client
Imports Oracle.DataAccess.Types
Public Class Login
Dim conn As New OracleConnection
Private Sub empID_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles empID.Click
End Sub
Private Sub LoginBtn_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles LoginBtn.Click
conn.ConnectionString = "User ID = Auto" & _
";Password = ********" & _
";Data Source = XE"
conn.Open()
Dim sq1 As String = "Return_Position" 'name of procedure
Dim cmd As New OracleCommand(sq1, conn)
cmd.CommandType = CommandType.StoredProcedure
cmd.Parameters.Add(New OracleParameter("I_EmpID", OracleDbType.Char, 4)).Value = Emp_ID.Text
Dim dataReader As OracleDataReader = cmd.ExecuteReader
dataReader.Read()
Dim position As New ListBox
position.Items.Add(dataReader.GetString(0)) 'were I am getting an error, I also tried using the dataReader.getstring(0) to store its value in a string but its a no go
If position.FindStringExact("MANAGER") = "MANAGER" Then
Me.Hide()
Dim CallMenu As New Menu()
CallMenu.ShowDialog()
End If
LoginBtn.Enabled = False
End Sub
I have read the oracle.net developer guide for using oracle in vb2010 and have successfully gotten through the document however they never use a stored procedure, since the teacher wants this program to user a layered architecture I cannot directly store sql queries like the document does, thus the reason I want to use stored procedures.
This is getting frustrating getting stuck with this having no background in VB, I could easily do this in c++ using file i/o even through it would be a pain in the rear....

Hello,
I am calling Oracle 11g stored procedures from VB.Net 2010. Here is a code sample (based on your code) you should be able to successfully implement in your application.
Please note that you may have to modify your stored procedure to include an OUT parameter (the employee position) if it doesn't have it yet.
Private Sub LoginBtn_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles LoginBtn.Click
Dim sProcedureName As String = "Return_Position" 'name of stored procedure
Dim ORConn as OracleConnection, sConn as String
Dim sPosition as String, sDataSource as String, sSchema as String, sPWD as String
Dim cmd As OracleCommand
'please provide below sDataSource, sSchema and sPWD in order to connect to your Oracle DB
sConn = "Data Source=" & sDataSource & ";User Id=" & sSchema & ";Password=" & sPWD & ";"
ORConn = New OracleConnection(sConn)
ORConn.Open()
cmd = New OracleCommand(sProcedureName, ORConn)
With cmd
.CommandType = Data.CommandType.StoredProcedure
'input parameter in your stored procedure is EmpId
.Parameters.Add("EmpID", OracleDbType.Varchar2).Value = Emp_ID.Text
.Parameters.Item("EmpID").Direction = ParameterDirection.Input
'output parameter in your stored procedure is Emp_Position
.Parameters.Add("Emp_Position", OracleDbType.Varchar2).Direction = ParameterDirection.Output
.Parameters.Item("Emp_Position").Size = 50 'max number of characters for employee position
Try
.ExecuteNonQuery()
Catch ex As Exception
MsgBox(ex.Message)
Exit sub
End Try
End With
sPosition = cmd.Parameters.Item("Emp_Position").Value.ToString
'close Oracle command
If Not Cmd Is Nothing Then Cmd.Dispose()
Cmd = Nothing
'close Oracle connection
If Not ORConn Is Nothing Then
If not ORConn.State = 0 Then
ORConn.Close()
End If
ORConn.Dispose()
End If
ORConn = Nothing
If UCase(sPosition) = "MANAGER" Then
Me.Hide()
Dim CallMenu As New Menu()
CallMenu.ShowDialog()
End If
LoginBtn.Enabled = False
End Sub
If you need further assistance with the code, please let me know.
Regards,
M. R.

I have a problem to extract data from oracle dump file (.dmp) using oracle database or any other tools.

There is IMP utility which provides me data as graphical way. But i need extract data in such a way so that i could able to use in my application.
thanks,
mohan

Hi,
EdStevens
Actually I was using SQL Developer. Sorry for the wrong define question. Now the real problem is:
I want to read or extract data in a txt file from Oracle Dump (.dmp) file without using Oracle sqlPlus or Oracle Database.
No need to say that i am able to extract dump data using sqlPlus. But for that, there is a little burden to install oracle database
or sql Developer.
I also listen about Oracle Loader a little bit. Is it a tool for providing extraction of data from Oracle dump file.
Thanks for your previous reply,
And now waiting for your suggestion.
thanks,
mohan

Oracle EBS Inbound/Outbound Interface build using Oracle SOA 11g

Hi SOA Guru's,
I am very much new to SOA 11g, could you guy's help me in understanding "How I can build any Oracle EBS Inbound/Outbound interface using Oracle SOA 11g"
It will be great if anybody explain me with any example script/screen shot/document.
Thanks in advance.
Regards
Pankaj

I don't have any experience with ebs, but i assume it works like this.
In the composite editor you will find a list adapters at the right..over here you will also find the oracle applications (ebs) adapter.
This will be the component for you which will communicate with the ebs packages.
you need to drag this adapter on the swim lane, and after that you should create the composite application like the way it's described in the tutorials Oracle supplies, put a mediator component in the middle and expose this interface (drag the line to the left swim line)
Hope it's a bit clear like this ?
http://download.oracle.com/docs/cd/E15523_01/integration.1111/e10224/fod_intro2.htm
this should make a few things clear too

Using Oracle Dataguard 10g With Oracle EBS

Hello,
I am working on Linux with Oracle Database 10g and Oracle EBS R12 and trying to configure Oracle Data Guard with Oracle EBS. I have been reading Oracle My Support Document (Business Continuity for Oracle E-Business Release 12 Using Oracle 11g Physical Standby Database [ID 1070033.1] ).
Please let me know of any another useful documents. It will also be helpful if anyone could share real time experiences.
Thank you.

Hi,
http://www.oracle.com/webfolder/technetwork/tutorials/obe/db/11g/r2/prod/ha/dataguard/physstby/physstdby.htm
http://www.oracle.com/technetwork/database/features/availability/dataguardoverview-083155.html
Regards
Yoonas

Cant connect to Oracle database using oracle db client

Hi All,
I recently created a virtual machine running windows server 2008 on my windows 7 host. Oracle database 11g is already installed on host OS(windows 7) and I have installed oracle 11g client on the guest OS(windows server 2008) and trying to connect to oracle database from remote server using oracle client but getting this error:
ORA-12504: TNS:listener was not given the SERVICE_NAME in CONNECT_DATAI am trying to connect using oracle client as below:
C:\Users\Administrator>SET ORACLE_SID = HR84DEV
C:\Users\Administrator>SQLPLUS /NOLOG
SQL*Plus: Release 11.2.0.1.0 Production on Fri Feb 10 06:16:34 2012
Copyright (c) 1982, 2010, Oracle. All rights reserved.
SQL> CONNECT SYSADM/[email protected]
ERROR:
ORA-12504: TNS:listener was not given the SERVICE_NAME in CONNECT_DATA
I have created database with name - HR84DEV
HOST ip address is - 192.168.56.1
I googled this error and as most of resources/blogs talked about having correct entry on listner.ora and tnsnames.ora file, I did the changes on both of these files accordingly.
PFB the cotent of both of these files:
tnsnames.ora
# tnsnames.ora Network Configuration File: C:\MyApps\Oracle\product\11.2.0\dbhome_\NETWORK\ADMIN\tnsnames.ora
# Generated by Oracle configuration tools.
LISTENER_ORCL =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.56.1)(PORT = 1521))
ORACLR_CONNECTION_DATA =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521))
(CONNECT_DATA =
(SID = CLRExtProc)
(PRESENTATION = RO)
HR84DEV =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.56.1)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = HR84DEV)
ORCL =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = orcl)
listner.ora
# listener.ora Network Configuration File: C:\MyApps\Oracle\product\11.2.0\dbhome_\network\admin\listener.ora
# Generated by Oracle configuration tools.
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = CLRExtProc)
(ORACLE_HOME = C:\MyApps\Oracle\product\11.2.0\dbhome_)
(PROGRAM = extproc)
(ENVS = "EXTPROC_DLLS=ONLY:C:\MyApps\Oracle\product\11.2.0\dbhome_\bin\oraclr11.dll")
(SID_DESC =
(SID_NAME = HR84DEV)
(ORACLE_HOME = C:\MyApps\Oracle\product\11.2.0\dbhome_)
(PROGRAM = extproc)
(ENVS = "EXTPROC_DLLS=ONLY:C:\MyApps\Oracle\product\11.2.0\dbhome_\bin\oraclr11.dll")
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.56.1)(PORT = 1521))
ADR_BASE_LISTENER = C:\MyApps\Oracle
Please not that I dont have any problem in connect to database locally.

Thanks Nicolas,
Actually, there was a problem with my oracle client installation. I uninstalled it and then installed back again but still, even after following your instructions I get some error.
Here what I did:
Created tnsnames.ora file as below:
HR84DEV =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.56.1)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = HR84DEV)
Placed it under appropriate directory and then checked the connection with database using the command shown below:
C:\Users\Administrator>tnsping HR84DEV
TNS Ping Utility for 32-bit Windows: Version 11.2.0.1.0 - Production on 10-FEB-2
012 08:42:03
Copyright (c) 1997, 2010, Oracle. All rights reserved.
Used parameter files:
C:\MyApps\Administrator\product\11.2.0\client_1\network\admin\sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)
(HOST = 192.168.56.1)(PORT = 1521))) (CONNECT_DATA = (SERVICE_NAME = HR84DEV)))
OK (20 msec)
Then tried to connect to database as below:
C:\Users\Administrator>SET ORACLE_SID=HR84DEV
C:\Users\Administrator>SQLPLUS /NOLOG
SQL*Plus: Release 11.2.0.1.0 Production on Fri Feb 10 08:25:56 2012
Copyright (c) 1982, 2010, Oracle. All rights reserved.
SQL> CONNECT SYSADM/SYSADM@HR84DEV
ERROR:
ORA-28547: connection to server failed, probable Oracle Net admin error
But still getting error.
I Googled this error and tried to figure out what the problem is and came across the possible cause which is because I haven't specify that the service should run as a user who is in domain admin group.
well, I am not really sure about this and dont know what user name and password I should enter in OracleserviceHR84DEV-properties-log on-this account.
do I really need to set this?

Re: Oracle Solaris Cluster 3.3 using Oracle Solaris 09/10 on virtualbox

Similar Messages

Maybe you are looking for