Re: Satellite Pro M70 - High CPU Usage - Low Performance

I sincerely hope someone can help. I do not consider myself really computer illiterate, but this is where my understanding ends and I would truly value all help offered.
I have a Toshiba Satellite Pro M70 of 2 yrs old and I am a definite advocate for Toshiba. However, my operating system is slow. Average day usage with Internet Explorer and Office 2007 is a painstaking process that takes too long. I have had conflicts with Trend Micro Internet Security 2008, which works perfectly.
But starting up the computer takes ages. CPU usage is usually high and System Idle Processes as well. I have reinstalled Windows XP from the Toshiba Boot DVD already 4 times with starting fresh and installing everything time and time again. Each time after getting everything up to speed again, the performance is disappointing.
I have extended RAM to 1,49 GB which made little difference from the original 1/3 of RAM. It seems that something is slowing down the computer, but this is not visable in the processes; other than quite a few svhost.exe processes that take little processing capacity nor CPU usage.
I have used Windows Gold Certified Uniblue Power Suite with a good registry cleaner. This helps a bit, but after a couple of days it seems to get only worse. I have an Intel Pentium M 1.73 GHz processor. Research online reveals that Trend Micro IS 2008 is quite good and demanding little capacity in comparison to competing security packages.
Is this system/software related or could this be a hardware issue?
Thanks in advance to all!

Hi!
This definitively not a hardware issue and I think should try to optimize some Windows settings to make your notebook faster.
At first you should clean the start up folder. Remove all programs that you dont need at start up. For example I dont have programs in the start up folder.
Furthermore you can customize the start up programs in msconfig (start => run => msconfig). There you can disable more programs that you dont need. Its your choice what do disable or enable.
You can improve the performance if you defragment your HDD from time time.
Remove all programs and trial software that you dont need and after this clean the registry. You can use CCleaner as Jimi said.
Try an other antivirus program. Maybe TrendMicro is not full compatible to the software that you use. I use AntiVir.
Bye

Similar Messages

  • Satellite T130-10T: High CPU usage for non apparent reason

    I have a brand new Satelitte T130.
    From unboxing, I remarked that CPU usage is most of the time very high, even when doing nothing (no applications are running).
    It sometimes hits 100% and stays ther for a few minutes.
    I installed the newest BIOST I could find on the Toshiba site, but nothing changes.
    Any ideas?
    I don't like this just-out-the-box-unit already causes troubles!

    Hi mate
    There are a lot of applications which are running in the background.
    Most of them are installed by Toshiba and such tools controls the notebook features like FN buttons, multi control buttons, eco button, etc
    You can see the ruing applications in task manager. There you can also see what background process needs the CPU usage.
    Greets

  • High CPU Usage on Satellite C655S5132

    High CPU usage On Satellite C655S5132 when running Window Explorer Internet and other programs. CPU use is so high it freezes computer. I have went back to original factory setting, ran virus programs nothing helps and flash player keep crashing. Please help.
    Desperate

    Has this been something that just recently started happening, or have you had this issue for a while?  Have you installed any new programs recently?
    You may want to download Glary Utilities, which is a free software(they will ask you if you want to go Pro, just say no, the free version works very well).  There is a module for startup manager.  You can go in and disable stuff that starts with the computer.  I would advise unchecking adobe, java, quicktime, printers, etc.  Anything that doesn't REALLY need to start with the computer.  The nice thing with Glary is that you can restart the computer, and if you find that you need one of the programs to start with windows, you can go back in and enable it again.
    The Celeron 925 processor in your computer is a decent entry level processor, but if there are too many programs running in the background, it can bog down quick.  I would also recommend downloading and running Malwarebytes Anti-malware, to be sure that there is nothing malicous running in the background. 
    Qosmio X875 i7-3630QM, 32GB RAM, OCZ SSD Qosmio X505 i7-920XM, PM55, 16GB RAM, OCZ SSD
    Satellite Pro L350 T9900, GM45, 8GB RAM , Intel 320 SSD (my baby) Satellite L655 i7-620M, HM55, 8GB RAM, Intel 710 SSD (travel system)

  • Excessively High CPU usage on my Equium M70

    HI,
    Recently in the last month my CPU usage as been hitting 100% when Im not running any taxing software (just internet explorer and windows media player).
    This is slowing down loading times and the area near the fan is pretty hot.
    I have an Equium M70-337, with a 1.7 centrino processor, and now 2 gigs of RAM (formerly 512 megabytes). I upgraded the ram in December and had no problem like this, now it's just started happening recently, I haven't installed anything that would do it, there are no unnecessary programs running and this was after I restored my comp to factory settings with the startup disc (about a month after) so it seems to have come from nowhere. On the task manager list it shows my web browser and media player using up the majority of CPU but I could have sworn that they didn't use up this much before.
    I don't know if the RAM would have been a factor but it was the correct ram for it and windows acknowledged to 2 gigs.
    Why would this have happened suddenly, any ideas guys?

    Hi
    I have the same notebook model and at the moment I do not have such problems. To be honest I have made clean OS installation 3 months ago and after Microsoft update installation I have noticed that notebook does not run like before. Just for example: if I use IE7 intensively with several different tabs in task manager I can see that IE need over 300.000 k of memory and somehow blocks. After closing IE and ending the IE process sin task manager I can work normally again.
    I really do not know how is your OS configured but in task manager you should see which running process is responsible for high CPU usage. Maybe some antivir application? Sorry but on this way it is really not easy to sayt why this happen. Play little bit with running processes.

  • How to upgrade Intel graphic/CPU on Satellite Pro M70

    Ok, here we go with my first posting. I have bought a Satellite Pro M70, about a year ago. It has a graphics chip (intel gtl 950?!), i just would like to know, if it is possible to install a graphics card, like ati or nvidia's.
    By the way, is it possible to upgrade the cpu? and how about warranty if upgrading and installing all that stuff?

    Here I go with my first answer to you ;)
    No, its not possible. The notebook technology is different as the desktop PCs and therefore you will be not able to upgrade the graphic card.

  • PKR crashing - high CPU usage (windows XP, bootcamp, Macbook Pro 2.5GHz)

    The PKR (3D online poker) client is crashing - often half way through a game, frustratingly. I'm running Windows XP via Bootcamp and have updated to the latest Apple Bootcamp drivers. I notice very high CPU usage (consistently maxing out a core) at all times when running PKR. Anyone else having trouble with this software?

    I've also been getting Kernel panics in OS X, so I took my MBP to the Apple Store in Regent St, London. They tested it and found a problem with the memory controller. After a logic board replacement the laptop is performing very well - no crashes so far in Windows or OS X. Fingers crossed.

  • High CPU usage on IPS

    Hi guys
    I got a problem with an IPS, from some weeks the CPU has been at 100% (all the 4 CPU's) and I don't know why, the Inspection Load is really low and I guess this is not affecting to this. Here some information of the SHOW VERSION command
    *I also attach some images of the IPS*
    Cisco Intrusion Prevention System, Version 7.1(1)E4
    Host:                                                    
        Realm Keys          key1.0                           
    Signature Definition:                                    
        Signature Update    S807.0              2014-06-13   
    OS Version:             2.6.29.1                         
    Platform:               ASA5585-SSP-IPS10               
    Using 4428M out of 5839M bytes of available memory (75% usage)
    system is using 25.1M out of 160.0M bytes of available disk space (16% usage)
    application-data is using 68.0M out of 171.6M bytes of available disk space (42% usage)
    boot is using 56.0M out of 70.5M bytes of available disk space (84% usage)
    application-log is using 494.0M out of 513.0M bytes of available disk space (96% usage)
    I hope somebody had some idea what could be causing the high cpu usage.
    Regards

    Has this been something that just recently started happening, or have you had this issue for a while?  Have you installed any new programs recently?
    You may want to download Glary Utilities, which is a free software(they will ask you if you want to go Pro, just say no, the free version works very well).  There is a module for startup manager.  You can go in and disable stuff that starts with the computer.  I would advise unchecking adobe, java, quicktime, printers, etc.  Anything that doesn't REALLY need to start with the computer.  The nice thing with Glary is that you can restart the computer, and if you find that you need one of the programs to start with windows, you can go back in and enable it again.
    The Celeron 925 processor in your computer is a decent entry level processor, but if there are too many programs running in the background, it can bog down quick.  I would also recommend downloading and running Malwarebytes Anti-malware, to be sure that there is nothing malicous running in the background. 
    Qosmio X875 i7-3630QM, 32GB RAM, OCZ SSD Qosmio X505 i7-920XM, PM55, 16GB RAM, OCZ SSD
    Satellite Pro L350 T9900, GM45, 8GB RAM , Intel 320 SSD (my baby) Satellite L655 i7-620M, HM55, 8GB RAM, Intel 710 SSD (travel system)

  • High CPU usage while buffering a video

    I have a high CPU usage (over 40%) while only buffering this video.
    IE10pre1
    Firefox Nightly 20121229, protected mode enabled
    Firefox Nightly 20121229, protected mode disabled
    Opera Next
    Chrome Canary
    a) open this url: http://www.wimp.com/marsearth/
    b) pause the video if it starts automatically
    c) use task manager or process explorer to view the cpu/gpu usage
    reproducible: mostly
    Windows 7 SP1
    Flash Player 11.6.602.108 / HWA enabled
    TestPC: Gigabyte GA-K8NS Pro; AMD Athlon 64 Venice 3200+; 2x 1GB MDT DDR-400-CL2; Club3D HD4670 AGP; Samsung HD103SJ, SyncMaster 204BM

    While we're aware of the issue, there's not much we can do about it.  The modern security realities facing web browsers have made sandboxing a necessity. 
    There's a good explanation of what's happening here: http://blogs.adobe.com/asset/2012/06/inside-flash-player-protected-mode-for-firefox.html
    Long story short, each video packet has to be passed from the browser to a medium-integrity broker process, then to the low-integrity flash player process for rendering.  If an attacker manages to hijack the Flash Player thread, the process is low-integrity, which prevents the attacker from doing much with it.  While it's not an absolute guarantee (nothing in security is), it raises the bar significantly for attackers.
    The downside is that all of that extra message-passing consumes CPU cycles, especially if you're trying to fill an exceptionally large buffer as fast as possible.  There's not a lot of opportunity to optimize this.
    If you're fine with the risk, you can manually disable ProtectedMode on your machine.  If you're only dealing with trusted sites, and you're not doing anything critical with the machine (work, banking, etc), then it's probably not a huge deal.
    Ultimately, ProtectedMode is like a vaccine -- it's a herd-immunity thing.  If the majority of people run it, exploits targeting machines without it are inconsistent and probably not worth pursuing when you look at the effort involved in developing an end-to-end exploit.  If a large number of people disable it, it becomes economically attractive for people building botnets, and you'll have a problem if you're not using it.
    To disable Protected Mode, add the following line to your mms.cfg file located in:
    Windows 32bit: C:\windows\system32\macromed\flash
    Windows 64bit: C:\windows\syswow64\macromed\flash
    ProtectedMode=0
    If the mms.cfg file does not exist, create one using any standard text editor (e.g.. notepad)
    Depending on your operating system, you might need to first save the mms.cfg file to a writable location (such as your documents or desktop folder) and then copy the file into the destination folder using Windows Explorer.
    To re-enable Protected Mode, simply remove the line from the mms.cfg file.

  • High CPU Usage on Cisco 3845

    Hi all,
    I'm having high CPU usage with one of my Cisco 3845.
    It works as an IP-IP Gateway and the CPU is quite high when the total number of calls only around 100-200 calls.
    I check the CPU usage with "show process cpu sort" and it looks like there are some "hidden" processes that consuming CPU.
    For example, 41% is total CPU, 25% is due to interrups, so CPU utilization on process level = 41 - 25 = 16%.
    But as showed below, processes don't consume that much CPU, only around 7% ???
    Please help to advise on this case. Any help is highly appreciated..
    Thank you.
    3845-GW#show process cpu sort | ex 0.00%  0.00%  0.00%
    CPU utilization for five seconds: 41%/25%; one minute: 46%; five minutes: 47%
     PID Runtime(ms)     Invoked      uSecs     5Sec   1Min   5Min TTY Process
     382     6619708     1473171       4493      1.59%  1.81%  1.92%   0 CCSIP_SPI_CONTRO
     141     4228940    10181955        415      1.35%  1.51%  1.57%   0 IP Input
      65     2450824      163102      15026        1.19%  1.16%  1.17%   0 Per-Second Jobs
     370     2702292     3709512        728        0.87%  0.88%  0.88%   0 VOIP_RTCP
     224      321680      245640       1309          0.47%  0.49%  0.50%   0 AFW_application_
     112       93940    18093506          5             0.39%  0.31%  0.32%   0 Ethernet Msec Ti
     384     1058280     1553567        681         0.23%  0.28%  0.30%   0 CCSIP_UDP_SOCKET
       2       18148       32905        551                 0.07%  0.03%  0.02%   0 Load Meter
     137       35644     4657843          7               0.07%  0.04%  0.05%   0 IPAM Manager
     189      206392      267959        770            0.07%  0.05%  0.07%   0 TCP Protocols
      30       30792      198554        155               0.07%  0.01%  0.00%   0 ARP Input
     368      145456      176151        825             0.07%  0.04%  0.05%   0 CC-API_VCM
      28        9628       32759        293  0.00%  0.01%  0.00%   0 Environmental mo
      48      221352       37922       5837  0.00%  0.11%  0.11%   0 Net Background
      63       16728       32924        508  0.00%  0.01%  0.00%   0 Compute load avg
      64       72080        2781      25918  0.00%  0.01%  0.00%   0 Per-minute Jobs
       6      371644       29792      12474  0.00%  0.14%  0.12%   0 Check heaps
     176       12216      240288         50  0.00%  0.01%  0.00%   0 CEF: IPv4 proces
     284       36416     4929826          7  0.00%  0.02%  0.01%   0 MMON MENG
     307       12168      806151         15  0.00%  0.01%  0.00%   0 Atheros LED Ctro
     335       35300       19755       1786  0.00%  3.16%  1.00% 708 Virtual Exec
    3845-GW#sh int g0/0
    GigabitEthernet0/0 is up, line protocol is up
      MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
         reliability 255/255, txload 1/255, rxload 1/255
      Encapsulation ARPA, loopback not set
      Keepalive set (10 sec)
      Full Duplex, 1Gbps, media type is RJ45
      output flow-control is XON, input flow-control is XON
      ARP type: ARPA, ARP Timeout 04:00:00
      Last input 00:00:00, output 00:00:00, output hang never
      Last clearing of "show interface" counters never
      Input queue: 0/75/2/56803 (size/max/drops/flushes); Total output drops: 0
      Queueing strategy: fifo
      Output queue: 0/40 (size/max)
      5 minute input rate 1551000 bits/sec, 5751 packets/sec
      5 minute output rate 4207000 bits/sec, 7643 packets/sec
         925128804 packets input, 939078510 bytes, 0 no buffer
         Received 62732 broadcasts (0 IP multicasts)
         0 runts, 0 giants, 2 throttles
         2 input errors, 0 CRC, 0 frame, 2 overrun, 0 ignored
         0 watchdog, 3763438515 multicast, 0 pause input
         1472816545 packets output, 3214770103 bytes, 0 underruns
         0 output errors, 2067720191 collisions, 1 interface resets
         0 unknown protocol drops
         0 babbles, 2281155551 late collision, 0 deferred
         2 lost carrier, 0 no carrier, 0 pause output
         0 output buffer failures, 0 output buffers swapped out
    3845-GW#sh int g0/1
    GigabitEthernet0/1 is up, line protocol is up
      MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
         reliability 255/255, txload 1/255, rxload 1/255
      Encapsulation ARPA, loopback not set
      Keepalive set (10 sec)
      Full Duplex, 1Gbps, media type is RJ45
      output flow-control is XON, input flow-control is XON
      ARP type: ARPA, ARP Timeout 04:00:00
      Last input 00:00:00, output 00:00:00, output hang never
      Last clearing of "show interface" counters never
      Input queue: 0/75/0/30335 (size/max/drops/flushes); Total output drops: 0
      Queueing strategy: fifo
      Output queue: 0/40 (size/max)
      5 minute input rate 1684000 bits/sec, 7697 packets/sec
      5 minute output rate 3372000 bits/sec, 5632 packets/sec
         1484558664 packets input, 2383177786 bytes, 0 no buffer
         Received 208998 broadcasts (0 IP multicasts)
         0 runts, 0 giants, 0 throttles
         2 input errors, 0 CRC, 0 frame, 2 overrun, 0 ignored
         0 watchdog, 3060386282 multicast, 0 pause input
         903478941 packets output, 2814588854 bytes, 0 underruns
         0 output errors, 2910776303 collisions, 1 interface resets
         0 unknown protocol drops
         0 babbles, 4157448025 late collision, 0 deferred
         2 lost carrier, 0 no carrier, 0 pause output
         0 output buffer failures, 0 output buffers swapped out

    Has this been something that just recently started happening, or have you had this issue for a while?  Have you installed any new programs recently?
    You may want to download Glary Utilities, which is a free software(they will ask you if you want to go Pro, just say no, the free version works very well).  There is a module for startup manager.  You can go in and disable stuff that starts with the computer.  I would advise unchecking adobe, java, quicktime, printers, etc.  Anything that doesn't REALLY need to start with the computer.  The nice thing with Glary is that you can restart the computer, and if you find that you need one of the programs to start with windows, you can go back in and enable it again.
    The Celeron 925 processor in your computer is a decent entry level processor, but if there are too many programs running in the background, it can bog down quick.  I would also recommend downloading and running Malwarebytes Anti-malware, to be sure that there is nothing malicous running in the background. 
    Qosmio X875 i7-3630QM, 32GB RAM, OCZ SSD Qosmio X505 i7-920XM, PM55, 16GB RAM, OCZ SSD
    Satellite Pro L350 T9900, GM45, 8GB RAM , Intel 320 SSD (my baby) Satellite L655 i7-620M, HM55, 8GB RAM, Intel 710 SSD (travel system)

  • High CPU usage in cisco 7613 with rsp720-3cxl

    Hi everybody,
    our cisco 7613 has about  4.5 Gbps  Tx/Rx IP traffic in total, and we run ospf with other cisco cloud for routing I list in the following some our router show.what is your idea about our high cpu usage .Is it in normal range with the listed cards and modules.How can I tune the rsp720 and other SIP-200,400,600 for better performances
    why our interrupt rate is high ,and one thing more the total sum of 5sec in separate rows not equal to cpu utilization for five second 50% 
    show proc cpu sor
    CPU utilization for five seconds: 50%/46%; one minute: 54%; five minutes: 59%
     PID Runtime(ms)     Invoked      uSecs   5Sec   1Min   5Min TTY Process
       8   196795220    12640741      15568  1.51%  0.38%  0.26%   0 Check heaps
     224  1048610528  4169501364          0  1.19%  1.45%  1.44%   0 IP Input
      13   374006320  3155162661          0  0.23%  0.26%  0.24%   0 ARP Input
     217   119862004   985030884        121  0.15%  0.32%  0.25%   0 ADJ resolve pro
    c
     185      537716  1825736183          0  0.07%  0.03%  0.02%   0 ACE Tunnel Task
     260     1550992  2983272818          0  0.07%  0.13%  0.15%   0 Ethernet Msec T
    i
     305    38186336    58050485        657  0.07%  0.02%  0.00%   0 XDR mcast
      34       67208    11707798          5  0.07%  0.00%  0.00%   0 IPC Loadometer
      27      232776    57160812          4  0.07%  0.01%  0.00%   0 IPC Periodic Ti
    m
     325    17539200    92894502        188  0.07%  0.15%  0.15%   0 CEF: IPv4 proce
    s
     195     7406636    43782487        169  0.07%  0.00%  0.00%   0 esw_vlan_stat_p
    r
    show ip route summ
    IP routing table name is default (0x0)
    IP routing table maximum-paths is 32
    Route Source    Networks    Subnets     Replicates  Overhead    Memory (bytes)
    static          1           120         0           7620        20812
    connected       0           313         0           18860       53836
    ospf 98         17          4892        0           589020      863984
      Intra-area: 89 Inter-area: 383 External-1: 0 External-2: 0
      NSSA External-1: 0 NSSA External-2: 4437
    bgp 12880       0           1           0           60          172
      External: 1 Internal: 0 Local: 0
    ospf 410        0           269         0           16220       47344
      Intra-area: 1 Inter-area: 0 External-1: 0 External-2: 268
      NSSA External-1: 0 NSSA External-2: 0
    internal        137                                             260544
    Total           155         5595        0           631780      1246692
    sh module
    Mod Ports Card Type                              Model              Serial No.
      1    0  4-subslot SPA Interface Processor-200  7600-SIP-200       
      2    0  4-subslot SPA Interface Processor-400  7600-SIP-400       
      3   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP       
      6    1  1-subslot SPA Interface Processor-600  7600-SIP-600       
      7    2  Route Switch Processor 720 (Active)    RSP720-3CXL-GE     
      8    2  Route Switch Processor 720 (Cold)      RSP720-3CXL-GE     
    show ver
    System image file is "bootdisk:c7600rsp72043-adventerprisek9-mz.122-33.SRE2.bin"
    1 SIP-200 controller .
    1 SIP-400 controller (1 Channelized OC3/STM-1).
    1 SIP-600 controller (1 TenGigabitEthernet).
    2 Virtual Ethernet interfaces
    28 Gigabit Ethernet interfaces
    1 Ten Gigabit Ethernet interface
    1 Channelized STM-1 port
    1 Channelized STM-1 port
    show int vlan 1
      Encapsulation ARPA, loopback not set
      Keepalive not supported
      ARP type: ARPA, ARP Timeout 04:00:00
      Last input 00:00:00, output 00:00:00, output hang never
      Last clearing of "show interface" counters 2d23h
      Input queue: 0/75/2886/1830 (size/max/drops/flushes); Total output drops: 0
      Queueing strategy: fifo
      Output queue: 0/40 (size/max)
      5 minute input rate 2380531000 bits/sec, 287383 packets/sec
      5 minute output rate 422133000 bits/sec, 254113 packets/sec
      L2 Switched: ucast: 1200869468 pkt, 101172643240 bytes - mcast: 253599 pkt, 78
    873415 bytes
      L3 in Switched: ucast: 60947040633 pkt, 68919665115039 bytes - mcast: 0 pkt, 0
     bytes mcast
      L3 out Switched: ucast: 52594517004 pkt, 9869168832783 bytes mcast: 0 pkt, 0 b
    ytes
         62147839148 packets input, 69016175499764 bytes, 0 no buffer
         Received 257634 broadcasts (0 IP multicasts)
         0 runts, 0 giants, 15 throttles
         0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
         53647248858 packets output, 10292998021217 bytes, 0 underruns
         0 output errors, 0 interface resets
         0 unknown protocol drops
         0 output buffer failures, 0 output buffers swapped out

    Thank you for your hints and replying
    These are our show ibc in 1 min interval
    Interface information:
            Interface IBC0/0
            5 minute rx rate 20045000 bits/sec, 30183 packets/sec
            5 minute tx rate 47394000 bits/sec, 60212 packets/sec
            19879272237 packets input, 4006174536193 bytes
            19835355282 broadcasts received
            19808585787 packets output, 3981305571968 bytes
            90548 broadcasts sent
            0 Bridge Packet loopback drops
            19756362091 Packets CEF Switched, 1320184 Packets Fast Switched
            0 Packets SLB Switched, 0 Packets CWAN Switched
            Label switched pkts dropped: 0    Pkts dropped during dma: 339549
            Invalid pkts dropped: 0    Pkts dropped(not cwan consumed): 0
            IPSEC pkts dropped: 635184
            Xconnect pkts processed: 0, dropped: 0
            Xconnect pkt reflection drops: 0
            Total paks copied for process level 0
            Total short paks sent in route cache 2605317676
            Total throttle drops 265338    Input queue drops 5831090
            total spd packets classified (120217214 low, 174503 medium, 3073 high)
            total spd packets dropped (339549 low, 0 medium, 0 high)
            spd prio pkts allowed in due to selective throttling (0 med, 0 high)
            IBC resets   = 1; last at 23:52:49.004 Sat Jan 19 2013
    Driver Level Counters: (Cumulative, Zeroed only at Reset)
              Frames          Bytes
      Rx(0)   26537712        3421085217
      Rx(1)   3449063135      2838813650
      Tx(0)   3390340306      2016620276
     Input Drop Frame Count
         Rx0 = 0                Rx1 = 2488435
     Per Queue Receive Errors:
         FRME   OFLW   BUFE   NOENP  DISCRD DISABLE BADCOUNT
     Rx0 0      0      0      0      0        0    0
     Rx1 0      0      0      3633   0        0    0
      Tx Errors/State:
       One Collision Error   = 0            More Collisions       = 0
       No Encap Error        = 0            Deferred Error        = 0
       Loss Carrier Error    = 0            Late Collision Error  = 0
       Excessive Collisions  = 0            Buffer Error          = 0
       Tx Freeze Count       = 0            Tx Intrpt Serv timeout= 1
       Tx Flow State         = FLOW_ON
       Tx Flow Off Count     = 0            Tx Flow On Count      = 0
      Counters collected at Idb:
       Is input throttled    = 0            Throttle Count        = 0
       Rx Resource Errors    = 0            Input Drops           = 2488435
       Input Errors           = 194243
       Output Drops          = 0            Giants/Runts          = 0/0
       Dma Mem Error         = 0            Input Overrun         = 0
    Hash match table for multicast (in use 0, maximum 64 entries):
    show ibc 
    Interface information:
            Interface IBC0/0
            5 minute rx rate 20194000 bits/sec, 30412 packets/sec
            5 minute tx rate 47753000 bits/sec, 60663 packets/sec
            19891125514 packets input, 4007158118761 bytes
            19847185365 broadcasts received
            19820407164 packets output, 3982279276274 bytes
            90576 broadcasts sent
            0 Bridge Packet loopback drops
            19768178233 Packets CEF Switched, 1321008 Packets Fast Switched
            0 Packets SLB Switched, 0 Packets CWAN Switched
            Label switched pkts dropped: 0    Pkts dropped during dma: 339549
            Invalid pkts dropped: 0    Pkts dropped(not cwan consumed): 0
            IPSEC pkts dropped: 635574
            Xconnect pkts processed: 0, dropped: 0
            Xconnect pkt reflection drops: 0
            Total paks copied for process level 0
            Total short paks sent in route cache 2606549061
            Total throttle drops 265338    Input queue drops 5831090
            total spd packets classified (120252754 low, 174531 medium, 3074 high)
            total spd packets dropped (339549 low, 0 medium, 0 high)
            spd prio pkts allowed in due to selective throttling (0 med, 0 high)
            IBC resets   = 1; last at 23:52:49.004 Sat Jan 19 2013
    Driver Level Counters: (Cumulative, Zeroed only at Reset)
              Frames          Bytes
      Rx(0)   26550723        3422835145
      Rx(1)   3461063605      176652699
      Tx(0)   3402319442      3368513724
     Input Drop Frame Count
         Rx0 = 0                Rx1 = 2490155
     Per Queue Receive Errors:
         FRME   OFLW   BUFE   NOENP  DISCRD DISABLE BADCOUNT
     Rx0 0      0      0      0      0        0    0
     Rx1 0      0      0      3633   0        0    0
      Tx Errors/State:
       One Collision Error   = 0            More Collisions       = 0
       No Encap Error        = 0            Deferred Error        = 0
       Loss Carrier Error    = 0            Late Collision Error  = 0
       Excessive Collisions  = 0            Buffer Error          = 0
       Tx Freeze Count       = 0            Tx Intrpt Serv timeout= 1
       Tx Flow State         = FLOW_ON
       Tx Flow Off Count     = 0            Tx Flow On Count      = 0
      Counters collected at Idb:
       Is input throttled    = 0            Throttle Count        = 0
       Rx Resource Errors    = 0            Input Drops           = 2490155
       Input Errors           = 194358
       Output Drops          = 0            Giants/Runts          = 0/0
       Dma Mem Error         = 0            Input Overrun         = 0
    Hash match table for multicast (in use 0, maximum 64 entries):
    and sorry what is your idea about total sum of 5sec in separate rows not equal to cpu utilization for five second 50% 

  • Satellite Pro M70 overheats and powers off

    Need some tech support with this problem.
    Satellite Pro M70 constant over heating problem. After 20-30 minutes of normal use (web browsing etc) the bottom of the laptop gets really hot near the fan, unbearably hot to the touch.
    If I play any games or do anything cpu intensive, it will eventually smell of burning and power off.
    All this time the CPU fan never spins! Just lets it get hotter and hotter. Strange thing is, when you first boot up, the CPU fan spins for about 5-6 seconds so it works! Already tried cleaning it, wasn't particularly dirty, the fan isnt jammed, it spins if u blow on it.....
    Tried updating to latest BIOS still overheats.....
    Tried all the toshiba utils for cpu temp monitoring etc, they indicate the CPU getting hotter and hotter well over 60C + but none of them (or other 3rd party utils) will detect the fan....!
    Any fix for this or is it just bad fan / temp sensor design?

    Hello smurftech_1
    I had the somewhat the same problem with my Satellite M70 (PSM76E-00500K-AS) after three years of usage (it's now just over 4 years old).
    In desperation I brought it to the official Toshiba maintenance workshop and a technician squirted air into the vent at the left-hand side of the laptop (using a simple little rubber bellows operated by a finger and thumb) and the problem was solved!
    The chap didn't even need to blow air into the vent underneath the laptop (where I saw today that dust had collected).
    No expensive repairs were needed. My only cost was in time and fuel getting to the workshop.
    Quite simply, dust had accumulated in the vent and was blocking the circulation of air, so the laptop was quickly overheateding and shutting itself down. It was a dreadfully awkward problem at the time.
    I hope this solves the problem.
    Best wishes,
    "Mannix".

  • Satellite Pro M70 wont Power up when on AC

    Hi
    I bought my dad a Satellite Pro M70 for his birthday and he's been using it for about 3 months. Suddenly without any reason it won't power up if its not connected to the AC. The battery is registering as 100% charged.
    When on AC everything is fine no issues.
    But when its not plugged into the AC it won't power up. Once powered up however you can unplug the AC and it will all work fine again.
    Any ideas?
    Should I try a BIOS update? or does anyone have any other suggestions?
    Thanks
    Gogz

    Hi
    Does this problem appear from the beginning?
    Sounds a little bit like an power supply electroninc malfunction and in such cases you should always ask the Toshiba service provider for an help.
    Dont worry, it seems the warranty is valid and every procedure should be done for free.
    But Im interesting if this will help you:
    Please try to disable powerplay in the graphic card properties and don't set the CPU to a low speed in Toshiba Power Saver in fixed mode.
    Check this option.

  • MSI KT6 Delta LSR SATA to PATA High CPU Usage Problem

    Well recently I've switch to my one of my other motherboards on my network to a MSI KT6 Delta LSR, it was working fine after a reformat, but I notice a few problems and that is 100% cpu usage for SATA to PATA, and vice versa, which seems really crazy. Then my network card performance is ISDN speed sluggish, and I tested my line to be working 100% with another mobo. But when I put another NIC on the same mobo it suffers the same speed problems.
    Any suggestions? The rig is specs:
    Barton 2500+
    Antec QuietPower 350W
    200GB Seagate SATA HDD
    40GB Seagate PATA HDD
    ATI Radeon 7500 AIW
    Audigy 2 Value
    Realtek 8139 NIC
    MSI KT6 Delta LSR Mobo
    2x512 MB PC 2700 RAM
    Pioneer 107D DVD Writer
    LG 16X DVD-ROM
    56K Modem (A-open)

    Shouldn't say what I don't know about SATA, but since I found below, I need ask if VIA 4in1 drivers are installed, preferably while in SafeMode I say:
    http://www.google.se/search?q=cache:X6ewgPiIHYcJ:www.qdi.nl/cgi-bin/bbs/YaBB.pl%3Fboard%3DP4I865%3Baction%3Ddisplay%3Bnum%3D1074174096+sata+to+pata+cpu+usage&hl=sv
    I recently installed 160g Seagate barracuda 7200.7 drive on SATA port. (I enabled the Bios using Auto) I have a P4I865pea-6al mother board, with two PATA drives . When copying files between the PATA drives on ide ports, to or from, the SATA drive, I notice the CPU usage goes up to 100%, but when copying files from one ide drive (the PATA drives) to another the CPU usage is very low.  
    Is there a bios setting that will allow me to copy files from the SATA drive to the Pata drives using a small amount of CPU power, found when just copying between the Primary and Secondary IDE drives? I am using Adobe premiere pro, which uses a lot of CPU power, and the high CPU usage of the SATA drive crashes this program? Any help would be appreciated
     Re: CPU usage with SATA drive?
    « Reply #1 on: Oct 30th, 2004, 7:17pm »  Quote  Modify  
    have you installed the newest chipset- and ide drivers ?

  • SBS 2011 - High CPU usage - Help me Microsoft forums! You're my only hope!

    My company supports a client that has a SBS 2011 server.  For about the past year, we've been fighting a recurring issue with performance on this server.  There are about ten local users and four remote users.  The server's CPU idles at
    about 60%-80% but is usally running when under *any* load from 80%-100%.  If you do anything on the console, it will stay pretty much at 100%.  These are not power users by any means.  The server is utilized for file/printer sharing, Exchange
    2010, and one flat file database application (non-SQL).  SharePoint is not utilized.
    Needless to say, our client is frustrated.  When opening files, using their database application, or doing anything Exchange-related, there is a large amount of lag on the client side.  First, here are the server's specs:
    Make:Dell PowerEdge T420
    OS: SBS 2011 Standard SP1
    CPU: 2 - Intel Xeon E5-2407
    Memory: 32GB
    RAID: RAID 1 - Operating System (C:)/Data Volume (E:) | RAID 5 - Data Volume (D:)
    Here is what we have tried to resolve this to finality:
    * Doubled resources - Initially the server had a single physical processor and 16GB of memory.  While these specs alone should have been fine, and were fine when the server was installed, we had periods of time where the server would just sit all day at
    100% usage.  We doubled the resources and while this seemed like it would fix the issue, we are still seeing abnormally high processor usage.
    * Removed all monitoring tools, antivirus, and backup software - As part of our testing, we removed our monitoring agent (LabTech) and antivirus (GFI Vipre).  Mozy is utilized for an off-site backup so that was disabled.  No dice.
    * Verified updates - We made absolutely sure the server was 100% patched.
    * Malware/Virus/Rootkit checks - We have ran scans checking for any potential issues with security.
    * Ran MBSA and MBCA to fix any issues with the server's configuration.
    There is no single process which is using all of the CPU, or we would simply be able to narrow it down.  Our calls to Microsoft support have yielded no answers.  The last call ended with Microsoft stating that a SBS server should always be running
    at high CPU usage.  Meanwhile, we have many other clients with less-beefy servers, with more users, who have no issues like these.
    So, I'm turning to you all.  I will gladly provide logs, configuration settings, even remote assistance sessions if you all can help shed some light on what might be causing my issues.
    Thank you!

    Some comments/ideas:
    How long was the server running after this screenshot?  I ask because store.exe is only got a 1GB of RAM which is really low - it should grab most of the RAM within a few hours.
    The server was up for about 12 hours.  I believe an adjustment was made before to limit the Exchange memory usage.
    Strange that SearchIndexer (wsearch service) is so high although that may be a startup condition.
    The LT* processes seem to be a 3rd party monitoring tool - no idea why it would ever need that much CPU though (I thought you disabled this?).
    We had, but we cannot go forever without monitoring our client's server.  It has been pulled off in the past and results on performance are pretty much the same.
    The taskmgr process run by amnet_admin has used a lot of total CPU Time.  What is it? (can't see the command line).
    That's the user I was logged in as when I took the screenshot.  Even the task manager seems to eat up the CPU.
    The sqlserver process right above it is also busy - may want to look at the command line and figure out which SQL database that is (SBS has 3 - WSUS, Sharepoint, and SBS monitoring)
    I believe that's the SharePoint database.  They don't currently use their site.  Would you recommend a removal and reinstallation?  I would not completely remove as I know SBS doesn't like you removing parts of the complete package.
    Strange that vds.exe is 10% - that is the interface to the disk management interface IIRC.  Perhaps your monitoring service has gone awry here - definitely lose it.
    I'll see about pulling it off and I'll see if there are any improvements.
    -- Al

  • High CPU Usage in Word 2013

    Hi everyone,
    I'm having an issue with Word 2013 and I'm hoping someone can help. Seen as I got fleeced for my TechNet subscription this year (the price given on the invoice doubled when I called up to pay!) I’d very much like to see a speedy fix from the Microsofties
    please! :D
    Recently, I've found that Word will consistently exhibit high CPU utilisation, ~50% on a dual core second generation Core i5.
    This continues, even when I’m not providing any input to or interacting with the Word window and even when the Word window is covered by other windows. Minimising Word causes its CPU usage to drop back down to zero.
    The strange thing is that, so far, I’ve only observed this with a single document. I started writing this document at the start of this week and it’s been authored exclusively on Word 2013. In fact I’m the only one who’s editing it and I’ve only used a single
    computer (and this one single install of Word 2013) to do so…
    There’s nothing particularly unusual about this document, and a different but similar document which uses the same themes and features (in fact the theme for the second document was created from the first one) doesn’t appear to cause the same issues. Both
    these documents are stored on SkyDrive, and are being edited directly from there.
    Initially I tried the much recommended tweaks of disabling hardware graphics acceleration and sub-pixel positioning, however neither of these has had any effect.
    I investigated a bit further using Sysinternals Process Monitor, and found that while Word is using a lot of CPU it’s actually looping very, very quickly polling for the existence of the registry key “HKCU\Software\Microsoft\Avalon.Graphics”.
    This key doesn’t exist on my system, and a quick test I conducted where I created it just lead to Word looping polling for more non-existent registry keys.
    My system is a HP Folio 13 running Windows 8 Pro x64 with Office 2013 (RTM, not Beta) 32 bit. Both Windows and Office are fully patched, as is everything else on the system.
    Thanks in advance for any help anyone can offer.
    Chris

    Hello again,
    After working on my problematic document some more, I believe I’ve found the cause of the issue.
    @Microsofties – I think this one is either a bug or a dodgy OOTB template…
    I noticed that the high CPU usage only seemed to occur when the document’s footer was displayed. Experimenting with some careful scrolling and zooming to hide footer (without actually using the “hide white-space” option) seemed to confirm this so I investigated
    the footer a bit more.
    My document was using the standard Word “Facet (Odd Page)” footer template with a couple of fields added to suit my needs, namely “Publish Date” and a page number.
    The template seems to be structured such that the content of the footer is inside two nested text boxes (one inside the other). I also noticed previously that this footer template also appears to “jump” up each page and back down again as I scrolled.
    So I deleted the footer and its text boxes, and recreated the same content, in the same position (using the standard paragraph alignment tools) by hand without the nested text boxes. This has, so far, fixed the issue!
    I also noticed that the CPU usage dropped right down to idle the moment I deleted the nested text boxes.
    Altogether, this leads me to conclude that the “Facet (Odd Page)” footer template in Word 2013 is the source of my issue. Specifically, I believe that the use of nested text boxes in this template causes Word’s interactions with the .Net 4.5 WPF to go a
    bit nuts, as evidenced by the infinite loop of request for the non-existent “Avalon.Graphics” WPF registry key I mentioned previously.
    It would be nice to see some feedback on this one, Microsoft people, if only to know if this is actually a general issue or is specific to my document!
    Thanks, Chris

Maybe you are looking for

  • Can I link iWeb and Web Gallery so Web Gallery appears as part of iWeb?

    Anyone know how to link iWeb to Web Gallery so the latter appears to be part of the former? Apple seems to have set them up to be separate things.

  • Set full screen mode

    Hi everyone It may not seem a JMF problem but i am hoping for some help. I am just trying to implment full screen on jmf player panel, i tried but the nothing is shown but a black screen the following is the code of whole program:- import java.awt.*;

  • ADF Input Text not showing

    Hi All, Can anyone help me out. I am using Jdev 10.1.3.3 and when I dragged the componet from Data Control as Input ADF W/ label and run the page the input text doesn't appear only the lable. Thanks in advance

  • Finding and changing ownership of files by uid

    In migrating to a laptop to allow the primary account to be a mobile user on a server, I deleted the user account. Since this user was also the admin for the machine, I now have a series of applications and files on the box which show 501:501 as the

  • Ndiswrapper won't work on 0.7.1 install [split]

    I can not get ndiswrapper working properly with the kernel and initrd support.