Re: Satellite U 500 usb sleep & charge not functioning

Hi all,
I have new satellite U500-PSUME9 that works fine except usb sleep & charge utility. Sorry if I ask stupid question amn't compter qualified person
Any help appreciated. Thanks in advance

Hi,
1. You should enable usb sleep & charge in BIOS
2. As I know, usb sleep & charge is only available for USB ports marked with a small flash sign.
3 Install/update usb sleep & charge utility from [Toshiba driver page|http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp]

Similar Messages

My firewire 800 and USB ports on not functioning!

My firewire 800 and USB ports on not functioning, I believe it is an issue the next driver loaders anyone, know how I can reset these?

You don't "reset" a driver (kext). And I don't believe it s a driver problem. However you might try doing a smc and pram reset to see if that "shakes the ports loose". Might work. Couldn't hurt to try.

Usb car charger not fully charge Nokia 5800

Hi,
I have a usb car charger with a cable that has a usb plug on one end, and on the other end
there is a nokia 2.0mm charger plug.
like this one:
http://www.myonetwothree.com/items/Electronics/MoAs009/MoAs_2003_22_CarChr/MoAs_2003_22_CarChr_02.jp...
But the problem is that it's not fully charge my Nokia 5800, only about 85%-90%.
Could this charger can fully charge a nokia 5800?
on the charger itself it's written "DC 5V +- 5% Max= 1000mA"
Thank you.

Voltage of the charger needs to be about 5.5 V to fully charge it. There are some car usb chargers which give 5.5 V some which give only 5 V. You need to check them and see if they work properly with your nokia.

DVD-RW for Satellite 2800-500: IDE1 error, drive not recognized

Installation of a DVDRW slim drive NEC ND6500 has caused an "IDE1 error" message on boot and the drive was not recognized.
Would the Toshiba SD-R6472 DVDRW drive be compatible with my Satellite 2800-500?
Does anyone know a way to make anyone of them work?
[Edited by: admin on 22-Jul-05 17:57]

If you took some effort in reading this:
http://www.cdrinfo.com/Forum/tm.asp?m=84345&mpage=15??
you would have known already.
Well, you always have people who know better, and ofcourse there are always people who know better....
(euh, never mind, hihi)
Ok about the IDE error.
Vasdiak has an ide error-notification.
I didn't.
In my case it was not recognized with the ND6500 connected and the 2nd controller dissapeared in bios and OS.
Nevertheless was there the same solution for what appeared the same problem.
This (and reading lot's of info on the web) got me thinking.
In case of NEC equipment(and maybe other brands as well) basically you have to look for a real OEM drives, which are configured as Master/Slave
Bulk & Retail drives are most of the time deliverd as CLS (even though retailers/dealers say otherwise), and that's no good for Satellite Pro 4600 (and many other toshiba laptops).
Just to cut to the chase:
The GNR-version of the NEC-ND6500A will work in a Toshiba Satellite Pro 4600 (2100 & 6100 too, and I think many more will).
As for the Toshiba SD-R6472 DVDRW:
My guess is it's the same problem with the same solution:
1.Buy a Master/Slave configured drive OR
2.modify it yourself by:
2a.soldering pin45&47 together (like I did).
2b.flashing the proper firmware (which is not always available/hard to get), which will result in reversed ATA.
Problem is that the NEC, Toshiba and many others do NOT sell (real)OEM-parts to the end-users, even though many retailers believe they do.
But that's merely because of the lack of consensus on how to interpret the meaning of "OEM".
Fact is that many retailers sell bulk-parts as if there where OEM, but that's wrong !
In my particular case:
I bought a NEC-ND6500A which was OEM-specified on the website (dealer), and after informing with the dealer I bought the drive.
The NEC did not work and I,amongst a lot of other things -->, contacted NEC.
I mentioned the "OEM-story" and NEC explained.
They won't deliver GNR-version to the end user, but he also told me the reverse ATA trick and send the proper firmware via email.
Then again I decided not to use reverse-ATA-firmware because it cannot be undone, and there is less available firmware in reverse-ATA mode (no problem if you want to use official firmware only, by the way).
To make things more confusing:
GEN-version is specified as master, also by Nec, but the Toshiba does not cope with it well.
And so do a lot of other laptops that cannot recognize CSEL-drives (which it really is !!).
Kinds of errors one can get: IDE-error, unpredictable behaviour, no DMA possible, etc...
The GNR-version (or GEN-version with soldering trick or reverse ATA-firmware) IS however recognized as master (or slave) drive on the 2nd controller....
Enfin, if people here are really interested in solving their problem I think I really got them started here.
My advise: put some effort into it (by reading link above and search the web).
Good luck to y'all !
Ger

Satellite P300D-110 integrated webcam is not functioning properly.

Hello everyone,
as the title says, the integrated webcam of my Toshiba Satellite P300D-110 is not functioning properly. Allow me to explain. Using the Camera Assistance Software I can take photo's and record music. If I try to record a video the preview screen turns up black and the end result tuns out black aswell, completely black.
Whenever I try to use my camera with applications such as MSN Live Messenger, Skype or at community websites using Firefox, Internet Explorer or Safari the application in question crashes.
*How did this happen?*
You tell me. This is how it went;
* Day 1: I've started up my laptop and looked at my fresh and clean install of windows vista home premium. I tried out my webcam using the webcam assistance software and it worked like a charm.
* Day 2: Once again I boot up my laptop and try to start my webcam only to find out that it no longer functions.
To give a quick summary of the thread;
* Using Camera Assistance Software provided by Toshiba I can take pictures.
* Using Camera Assistance Software provided by Toshiba I can record sound.
* Using Camera Assistance Software provided by Toshiba I can _*NOT*_ record or preview a video.
* I can not start my camera using any other application such as but not limited to; MSN Live Messenger, Skype, Mozilla Firefox, Internet Explorer and Safar.
* I have downloaded and isntalled the latest drivers from the Toshiba website.
* My laptop is about a week old.
I'm not sure what more I can do, all I want is for the webcam to work, if anyone can help me out please do so.
And if possible WITHOUT having to reinstall Windows Vista Home Premium.
I haven't even used it and wouldn't want to make that a solution for all the problems that might occur in the future.
Sincerely,
a sad customer.

Using Camera Assistance Software provided by Toshiba I can NOT record or preview a video.
Can you please describe the steps how you try to do this? I must ask you this because it runs well on my notebook. When the recording is finished player opens and you can see recorded movie. It is avi format and at the top of this player you can see the path where the movie is saved.
Most strange thing for me is that you cannot use it with Skype. Ok for MSN is not the perfect but there is absolutely no problem with Skype. Check the settings and it must work somehow.

After upgrade to 10.8.3 Sleep mode not functioning

iMac
OSX 10.8.3
Sleep mode does not function properly.

In what way is it not functioning properly? If you go to System Preferences > Energy Saver are the sleep mode times where you want them? When you logout, do you then click Sleep or do you let the iMac go to sleep according to the settings? Do you have trouble coming out of sleep mode?

USB 2.0 not functioning properly after upgrading to 3.10.3-1 kernel

After upgrading to the 3.10.3-1 kernel USB 2.0 is not working anymore on my ASrock ION330 nettop.
I just did a system upgrade (including a kernel upgrade to 3.10.5-1), but the problem remains...
Here's the relevant messages that I extracted with journalctl -b
Aug 07 09:59:11 alcyone kernel: ACPI: bus type USB registered
Aug 07 09:59:11 alcyone kernel: usbcore: registered new interface driver usbfs
Aug 07 09:59:11 alcyone kernel: usbcore: registered new interface driver hub
Aug 07 09:59:11 alcyone kernel: usbcore: registered new device driver usb
Aug 07 09:59:11 alcyone kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Aug 07 09:59:11 alcyone kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Aug 07 09:59:11 alcyone kernel: ehci-pci: EHCI PCI platform driver
Aug 07 09:59:11 alcyone kernel: ohci_hcd 0000:00:04.0: setting latency timer to 64
Aug 07 09:59:11 alcyone kernel: ohci_hcd 0000:00:04.0: OHCI Host Controller
Aug 07 09:59:11 alcyone kernel: ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 1
Aug 07 09:59:11 alcyone kernel: ohci_hcd 0000:00:04.0: irq 16, io mem 0xfae7f000
Aug 07 09:59:11 alcyone kernel: hub 1-0:1.0: USB hub found
Aug 07 09:59:11 alcyone kernel: hub 1-0:1.0: 6 ports detected
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: setting latency timer to 64
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: EHCI Host Controller
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: new USB bus registered, assigned bus number 2
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: debug port 1
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: cache line size of 64 is not supported
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: irq 18, io mem 0xfae7ec00
Aug 07 09:59:11 alcyone kernel: ehci-pci 0000:00:04.1: USB 2.0 started, EHCI 1.00
Aug 07 09:59:11 alcyone kernel: hub 2-0:1.0: USB hub found
Aug 07 09:59:11 alcyone kernel: hub 2-0:1.0: 6 ports detected
Aug 07 09:59:11 alcyone kernel: hub 1-0:1.0: USB hub found
Aug 07 09:59:11 alcyone kernel: hub 1-0:1.0: 6 ports detected
Aug 07 09:59:11 alcyone kernel: usb 2-2: new high-speed USB device number 3 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-2: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: new high-speed USB device number 4 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-2: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: new high-speed USB device number 5 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-2: device not accepting address 5, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-2: new high-speed USB device number 6 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-2: device not accepting address 6, error -71
Aug 07 09:59:11 alcyone kernel: hub 2-0:1.0: unable to enumerate USB device on port 2
Aug 07 09:59:11 alcyone kernel: usb 2-3: new high-speed USB device number 7 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-3: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: new high-speed USB device number 8 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-3: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: new high-speed USB device number 9 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-3: device not accepting address 9, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-3: new high-speed USB device number 10 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-3: device not accepting address 10, error -71
Aug 07 09:59:11 alcyone kernel: hub 2-0:1.0: unable to enumerate USB device on port 3
Aug 07 09:59:11 alcyone kernel: usb 2-5: new high-speed USB device number 12 using ehci-pci
Aug 07 09:59:11 alcyone kernel: usb 2-5: device descriptor read/64, error -71
Aug 07 09:59:11 alcyone kernel: usb 2-5: device descriptor read/64, error -71
Aug 07 09:59:12 alcyone kernel: usb 2-5: new high-speed USB device number 13 using ehci-pci
Aug 07 09:59:12 alcyone kernel: usb 2-5: device descriptor read/64, error -71
Aug 07 09:59:12 alcyone kernel: usb 2-5: device descriptor read/64, error -71
Aug 07 09:59:12 alcyone kernel: usb 2-5: new high-speed USB device number 14 using ehci-pci
Aug 07 09:59:13 alcyone kernel: usb 2-5: device not accepting address 14, error -71
Aug 07 09:59:13 alcyone kernel: usb 2-5: device not accepting address 15, error -71
Aug 07 09:59:13 alcyone kernel: hub 2-0:1.0: unable to enumerate USB device on port 5
Aug 07 09:59:13 alcyone systemd[1]: Found device MCP79 Ethernet.
Aug 07 09:59:14 alcyone kernel: usb 1-1: new low-speed USB device number 2 using ohci_hcd
Aug 07 09:59:14 alcyone kernel: usb 1-4: new low-speed USB device number 3 using ohci_hcd
I'm glad that keyboard and mouse are working properly under USB 1.0, but neither my usb-parport printer nor my USB external hard drive are recognised any more :-(
Any ideas how to solve this?? (I'd prefer not to downgrade the kernel)
Last edited by zilverling (2013-08-07 14:28:36)

I've discovered it's not that USB 2.0 is not working. 3 out of 6 usb ports/busses seem to work properly. The other three seem totally dead. Obviously this was not the case under kernel 3.9.9-1. Downgrading to kernel 3.10.2 made no difference.
In practical terms this means that I can use my printer and access my external drive if I use the right port/bus. And I could probably work around the problem by plugging a USB hub in one of the working ports. But I would be happy to get rid of the error messages and have all 6 usb busses working as they did before...

Sleep Mode not functioning correctly after Mac OSX 10.6.5 update

Hi
I have a Macbook Model Identifier 5,1. (1st gen Alum Macbook). I notice that after I updated to 10.6.5, I have a problem going to sleep mode. When I click on sleep, it will blacken the screen but the LED screen still glows. Usually, it glows for a few second and then the LED powers down so it will be completely dark. Now it just hangs there. I have to use the power down fucntion by pressing it for 4 seconds.
I tried disk utility repair permissions. ANy suggestions?
Antonio

Hi
I have similar problem with MacBook White Identifier 6.1. I have update 10.6.5 and I have a lot of problems with my MacBook. This problem is one of them. My MacBook also often show message Kernel Panic and I can use only power button. It is not good when arrange photos or do other things.
Update 10.6.4 was very good. I didn't have any problem. If I have version 10.6.5, can I return to version 10.6.4?
I don't know, what I can do. Any suggestions?
Thanks

Right side USB port is not functional on my new Spectre13

I just purchased a new Spectre13 notebook and the USB port on the right side isn't functionnal. I searched in different places in the system and I cannot find a way to get it working. Is this normal?

And now the left side USB port doesn't recognise my 16GB USB key anymore. It does recognise a Logitech wireless mouse key but not my key.
Since it works fine on My MacBook, I know the problem isn't the USB key.

Ipod only working in usb 1.1. USB 2.0 not functioning properly in XP Pro

Title really says it all, the ipod will dock, but I get a windows message "the device can work faster if you plug it into a high speed usb port" All my ports are usb 2.0. The motherboard is an Abit IC7-Max3. Xp Pro SP2 installed, I've uninstalled the usb controller and let it reinstall and it still gives me the same error, weird thing is I plug it into my friends computer and get teh same error, but his PSP will dock fine at 2.0 speeds. Could this be something as simple as the wrong cable? Any help is appreciated, took over 6 hours to transfer 18gb of music to my ipod and I'm constantly adding more. Syncing just takes soooo long.

i just went over to abit to do some research, and found your thread in the forums over there. so apparently you have tried plugging the ipod into the back ports rather than the front ports.
have you got any other USB 2.0 peripherals connected to that PC at the moment? sometimes power drain through one port will affect an ipod connection on a different USB 2.0 port (and vice versa).
so by way of experiment, do you get a 2.0 connection if you unplug other peripherals first?
love, b

USB keyboard is not functioning. its locked?

I cant type anything but I tried numerous key combinations (resetting pram for instance) so i tried random combos. I got it to type a little after using a combo using either f5 or f6 but then I couldnt anymore? I need help unlocking the keyboard? I cant move anywhere from the login window since I cant type. I tried unplugging and plugging keyboard back in and it doesnt work. I even connected it to a different computer and it just doesnt work.

Press option key 5 times.
If this does not help, contact Apple.

BLACKBERRY PLAYBOOK CHARGER NOT FUNCTIONING

I need a Blackberry Playbook Charger , Please let me Know where can I find I am staying in Jeddah Saudi Arabia .
Or I Need a Technical Team Guy who can come and check my Playbook .I tried with Axiom but there was no use they just give me a toll free no 80008147911.
Thanks and regards
Ashraf

Hi and Welcome to the Community!
Is there any chance it got wet? The symptom you describe sounds quite similar to what can happen in that case. If so, then:
REMOVE YOUR BB BATTERY NOW!!!
Run, don't walk, to this FAQ:
http://www.blackberryfaq.com/index.php/Got_Your_BlackBerry_Wet%3F
Do everything it says, including waiting the maximum recommended time. Applying power to your BB between it getting wet and doing this process reduces the chances of success. Further, the only thing predictable about moisture intrusion into a BB (indeed, any electronic device) is that the results will be unpredictable. I've seen some come back up right away and be fine. I've seen others never work at all. I've seen still others run for a bit, and then die later. And every thing in between.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

W510 usb 3.0 not functioning

I have a Lenovo w510 and ever since I've installed my SSD, my USB 3.0 has been transfering anywhere between 13mb/s to 45mb/s. I've tried multiple different harddrives as well and I'm getting about the same results. I even get notifications once in a while saying that my device can perform faster if I plug it into the USB 3.0 port even though it's all ready in the USB 3.0 port. I've updated all my drivers and firmware and it's still performing fairly low. Any suggestions?

Can you try copying one big file? Conventional hard drives have trouble accepting large amounts of small files, causing transfer rate to drop significantly.
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

HP Pavilion dv6-6b10tx two of the usb ports are not working

I have recently bought a HP Pavilion dv6-6b10tx....and had it fixed by hp for a problem with the beeping noise.
After sending my laptop for repairs( replacing the system board), I received my laptop but two of my usb ports are not functioning...
I did a bios update and did the hp update to see if it actually fix anything but not luck. So I went device manager and found a exclamation mark on the renesas electronics usb 3.0 host controller with a device status 'This device cannot start. (Code 10)'. What do i do??

The question is why is the port not working? Is something in the port that you can see? If not, then there isn't much you can do but take the computer in to the genius bar and have the techs see if it is a circuit problem that can be fixed.

USB Keyboard/Mouse do not function in Bios (Bios Change log too)

I have 1.7 and the system seems fairly stable, a few BSOD's occasionally and it normally seems to occur when the system is idle. I can work on that, but now when I boot my usb keyboard will not function for the EFI/Bios. I have a Old PS2 keyboard working for now but was hoping there is some work around that someone might now. Everything is enabled in the Bios and I even disabled, saved, re- enabled, saved.
Saving (F10) still causes the system to power down, but I can live with that.
Now for the BIOS, can we get a change log to determine what issues are being resolved with these update? I have 1.8b7 downloaded but last update I lost my Raid array so I want to see change logs before a possible rebuild.
Lastly I am used to new hardware having issues especially with OCing, but the EFI/BIOS seems extremely temperamental. First MSI board and my work is on the road a lot so I am hoping to get some of this fixed soon.
Thanks for any advice

Quote
a few BSOD's
What are the Stop: error codes? 124? 050?
Quote
Now for the BIOS, can we get a change log to determine what issues are being resolved with these update? I have 1.8b7 downloaded but last update I lost my Raid array so I want to see change logs before a possible rebuild.
https://forum-en.msi.com/index.php?topic=144655.0

Re: Satellite U 500 usb sleep & charge not functioning

Similar Messages

Maybe you are looking for