Re: Sattelite M305D-S4830 Volume Dial Strange Behavior

Hello, I am having a strange issue with my volume control dial on the Satellite M305D-S4830. I am not sure when this error began happening, but now my volume control dial produces the letters C and B when I roll it clockwise/counterclockwise. here, I'll roll it cw/c-cw right now:
ccccccccccccbccccccccccccccccccccbbccccc
It produces the b's less often than the c's as you can see. Also, it does adjust volume bar but erratically: when I roll it clockwise it decreases the volume and then sharply increases the volume immediately. Rotating it counter-clockwise does increase the volume sharply and sometimes it decreases the volume a little bit.
I have the latest drivers for my Satellite and have not altered the OS or Services (such as HID Input service) in any way. I have tried using a previous driver version for the sound but this has not changed anything. Thanks for your time.

Hi
Someone had a similar issue. I read about this here in one of threads (if you want use the search option).
The point is that the technician has cleaned the volume wheel (contacts, etc...) and this solves this issue.
I dont know if this is a same reason in your case but its worth a try
Note; dont disassemble the notebook or similar!!! This can be done ONLY by ASP due to some hardware damage and warranty validity!
PS: Of course the BIOS update is advisable too.

Similar Messages

Strange behavior of system with enabled FileVault2, Roaming profile

Hello,
I have encountered strange behavor of my Macbook Air after some testing.
Macbook Air 2012 was newly installed with 10.8.4 and joined network account server on 10.8.4 server with Roaming profile (synced with server home directory). After installing some basic apps like iWork I turned on FileVault.
Then I start to have the strange behavior - iWorks are not displaying content of document - it seams blank - just white screen without any borders where should be at least lines in numbers or empty cells.
Another display problem is in Safari. On same pages (even default Top SItes) it`s flashing and especially when scrolling.
Did you encountered something similar? I`m not able to get rid of it.
Computers was used for some time before turining on FIle Vault and problem started to occur after this action. Disabling of FileVault didn`t helped (properly restarted between steps).
I didn`t found anything strange in Console or elsewhere..

Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your personal files or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, or by corruption of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and Wi-Fi on certain iMacs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of steps 1 and 2.

Strange behavior after suspend.

Hi,
For some time I have a strange behavior of my system after I awake my computer(after suspend). This problem don't disappear after update.
Ok, so if I suspend my computer, and awake him I can't run any program. Even if i was open some application, this application crashes. I have to restart my machine.
Somebody had similar problem or know how help?
I'm using Arch Linux x64, kernel 3.8, openbox. Suspend by "systemctl suspend".

OK, maybe good idea is paste here my output journal:
# journalctl --since=today | tac | sed -n '/-- Reboot --/{n;:r;/-- Reboot --/q;p;n;b r}' | tac
-- Logs begin at Mon 2012-09-10 20:20:07 CEST, end at Thu 2013-03-28 10:17:18 CET. --
Mar 28 10:10:36 localhost kernel: Freezing user space processes ... (elapsed 0.01 seconds) done.
Mar 28 10:10:36 localhost systemd[1]: Time has been changed
Mar 28 10:10:36 localhost systemd[1]: systemd-tmpfiles-clean.timer: time change, recalculating next elapse.
Mar 28 10:10:36 localhost kernel: Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Mar 28 10:10:36 localhost dhcpcd[1435]: eth1: carrier lost
Mar 28 10:10:36 localhost kernel: PM: Entering mem sleep
Mar 28 10:10:36 localhost kernel: Suspending console(s) (use no_console_suspend to debug)
Mar 28 10:10:36 localhost kernel: sd 0:0:0:0: [sda] Synchronizing SCSI cache
Mar 28 10:10:36 localhost kernel: sd 0:0:0:0: [sda] Stopping disk
Mar 28 10:10:36 localhost kernel: cfg80211: Calling CRDA for country: PL
Mar 28 10:10:36 localhost kernel: <6>[fglrx] IRQ 46 Disabled
Mar 28 10:10:36 localhost kernel: <6>[fglrx] Preparing suspend fglrx in kernel.
Mar 28 10:10:36 localhost kernel: <6>[fglrx] Suspending fglrx in kernel completed.
Mar 28 10:10:36 localhost kernel: <6>[fglrx] Power down the ASIC .
Mar 28 10:10:36 localhost kernel: PM: suspend of devices complete after 1126.292 msecs
Mar 28 10:10:36 localhost kernel: PM: late suspend of devices complete after 0.263 msecs
Mar 28 10:10:36 localhost kernel: r8169 0000:09:00.0: System wakeup enabled by ACPI
Mar 28 10:10:36 localhost kernel: ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
Mar 28 10:10:36 localhost kernel: PM: noirq suspend of devices complete after 52.988 msecs
Mar 28 10:10:36 localhost kernel: ACPI: Preparing to enter system sleep state S3
Mar 28 10:10:36 localhost kernel: PM: Saving platform NVS memory
Mar 28 10:10:36 localhost kernel: Disabling non-boot CPUs ...
Mar 28 10:10:36 localhost kernel: smpboot: CPU 1 is now offline
Mar 28 10:10:36 localhost kernel: smpboot: CPU 2 is now offline
Mar 28 10:10:36 localhost kernel: smpboot: CPU 3 is now offline
Mar 28 10:10:36 localhost kernel: Extended CMOS year: 2000
Mar 28 10:10:36 localhost kernel: ACPI: Low-level resume complete
Mar 28 10:10:36 localhost kernel: PM: Restoring platform NVS memory
Mar 28 10:10:36 localhost kernel: Extended CMOS year: 2000
Mar 28 10:10:36 localhost kernel: CPU0: Thermal monitoring handled by SMI
Mar 28 10:10:36 localhost kernel: Enabling non-boot CPUs ...
Mar 28 10:10:36 localhost kernel: smpboot: Booting Node 0 Processor 1 APIC 0x4
Mar 28 10:10:36 localhost kernel: CPU1: Thermal monitoring handled by SMI
Mar 28 10:10:36 localhost kernel: CPU1 is up
Mar 28 10:10:36 localhost kernel: smpboot: Booting Node 0 Processor 2 APIC 0x1
Mar 28 10:10:36 localhost kernel: CPU2: Thermal monitoring handled by SMI
Mar 28 10:10:36 localhost kernel: CPU2 is up
Mar 28 10:10:36 localhost kernel: smpboot: Booting Node 0 Processor 3 APIC 0x5
Mar 28 10:10:36 localhost kernel: CPU3: Thermal monitoring handled by SMI
Mar 28 10:10:36 localhost kernel: CPU3 is up
Mar 28 10:10:36 localhost kernel: ACPI: Waking up from system sleep state S3
Mar 28 10:10:36 localhost kernel: ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
Mar 28 10:10:36 localhost kernel: sdhci-pci 0000:07:00.0: MMC controller base frequency changed to 50Mhz.
Mar 28 10:10:36 localhost kernel: sdhci-pci 0000:07:00.0: proprietary Ricoh MMC controller disabled (via firewire function)
Mar 28 10:10:36 localhost kernel: sdhci-pci 0000:07:00.0: MMC cards are now supported by standard SDHCI controller
Mar 28 10:10:36 localhost kernel: PM: noirq resume of devices complete after 133.780 msecs
Mar 28 10:10:36 localhost kernel: PM: early resume of devices complete after 0.127 msecs
Mar 28 10:10:36 localhost kernel: ehci-pci 0000:00:1a.0: setting latency timer to 64
Mar 28 10:10:36 localhost kernel: mei 0000:00:16.0: irq 43 for MSI/MSI-X
Mar 28 10:10:36 localhost kernel: snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
Mar 28 10:10:36 localhost kernel: pci 0000:00:1e.0: setting latency timer to 64
Mar 28 10:10:36 localhost kernel: ehci-pci 0000:00:1d.0: setting latency timer to 64
Mar 28 10:10:36 localhost kernel: ahci 0000:00:1f.2: setting latency timer to 64
Mar 28 10:10:36 localhost kernel: snd_hda_intel 0000:02:00.1: irq 45 for MSI/MSI-X
Mar 28 10:10:36 localhost kernel: r8169 0000:09:00.0: System wakeup disabled by ACPI
Mar 28 10:10:36 localhost kernel: <6>[fglrx] Power up the ASIC
Mar 28 10:10:36 localhost kernel: <6>[fglrx] Preparing resume fglrx in kernel.
Mar 28 10:10:36 localhost kernel: Extended CMOS year: 2000
Mar 28 10:10:36 localhost kernel: <6>[fglrx] Resuming fglrx in kernel completed.
Mar 28 10:10:36 localhost kernel: <6>[fglrx] IRQ 46 Enabled
Mar 28 10:10:36 localhost kernel: ata5: SATA link down (SStatus 0 SControl 300)
Mar 28 10:10:36 localhost kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Mar 28 10:10:36 localhost kernel: ata2.00: configured for UDMA/100
Mar 28 10:10:36 localhost kernel: usb 2-1.3: reset low-speed USB device number 3 using ehci-pci
Mar 28 10:10:36 localhost kernel: sdhci-pci 0000:07:00.0: Will use DMA mode even though HW doesn't fully claim to support it.
Mar 28 10:10:36 localhost kernel: firewire_core 0000:07:00.3: rediscovered device fw0
Mar 28 10:10:36 localhost kernel: usb 1-1.4: reset high-speed USB device number 3 using ehci-pci
Mar 28 10:10:36 localhost kernel: ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 28 10:10:36 localhost kernel: ata1.00: configured for UDMA/133
Mar 28 10:10:36 localhost kernel: sd 0:0:0:0: [sda] Starting disk
Mar 28 10:10:36 localhost kernel: PM: resume of devices complete after 2478.795 msecs
Mar 28 10:10:36 localhost kernel: PM: Finishing wakeup.
Mar 28 10:10:36 localhost kernel: Restarting tasks ... done.
Mar 28 10:10:36 localhost kernel: video LNXVIDEO:00: Restoring backlight state
Mar 28 10:10:36 localhost slim[806]: Conky: can't open /sys/class/power_supply/BAT0/uevent: No such file or directory
Mar 28 10:10:36 localhost slim[806]: Conky: can't open /proc/acpi/battery/BAT0/state: No such file or directory
Mar 28 10:10:36 localhost systemd-sleep[4208]: System resumed.
Mar 28 10:10:36 localhost dbus-daemon[800]: dbus[800]: [system] Activating via systemd: service name='org.freedesktop.UPower' unit='upower.service'
Mar 28 10:10:36 localhost dbus[800]: [system] Activating via systemd: service name='org.freedesktop.UPower' unit='upower.service'
Mar 28 10:10:36 localhost su[4307]: (to root) root on none
Mar 28 10:10:36 localhost su[4307]: pam_unix(su:session): session opened for user root by (uid=0)
Mar 28 10:10:36 localhost systemd[1]: Starting Daemon for power management...
Mar 28 10:10:36 localhost su[4307]: pam_unix(su:session): session closed for user root
Mar 28 10:10:36 localhost su[4328]: (to root) root on none
Mar 28 10:10:36 localhost su[4328]: pam_unix(su:session): session opened for user root by (uid=0)
Mar 28 10:10:36 localhost su[4328]: pam_unix(su:session): session closed for user root
Mar 28 10:10:36 localhost systemd[1]: Started Suspend.
Mar 28 10:10:36 localhost systemd[1]: Service sleep.target is not needed anymore. Stopping.
Mar 28 10:10:36 localhost systemd[1]: Stopping Sleep.
Mar 28 10:10:36 localhost systemd[1]: Stopped target Sleep.
Mar 28 10:10:36 localhost systemd[1]: Starting Suspend.
Mar 28 10:10:36 localhost systemd[1]: Reached target Suspend.
Mar 28 10:10:36 localhost systemd-logind[796]: Operation finished.
Mar 28 10:10:36 localhost laptop-mode[4441]: Laptop mode
Mar 28 10:10:36 localhost laptop-mode[4446]: enabled, active [unchanged]
Mar 28 10:10:36 localhost logger[4463]: ACPI action undefined: ACPI0003:00
Mar 28 10:10:36 localhost laptop-mode[4501]: Laptop mode
Mar 28 10:10:36 localhost laptop-mode[4509]: enabled, active [unchanged]
Mar 28 10:10:36 localhost laptop-mode[4534]: Laptop mode
Mar 28 10:10:36 localhost laptop-mode[4539]: enabled, active [unchanged]
Mar 28 10:10:36 localhost laptop-mode[4554]: Laptop mode
Mar 28 10:10:36 localhost laptop-mode[4557]: enabled, active [unchanged]
Mar 28 10:10:36 localhost laptop-mode[4562]: Laptop mode
Mar 28 10:10:36 localhost laptop-mode[4563]: enabled, active [unchanged]
Mar 28 10:10:36 localhost dbus-daemon[800]: dbus[800]: [system] Successfully activated service 'org.freedesktop.UPower'
Mar 28 10:10:36 localhost dbus[800]: [system] Successfully activated service 'org.freedesktop.UPower'
Mar 28 10:10:36 localhost systemd[1]: Started Daemon for power management.
Mar 28 10:10:37 localhost ntpd[1442]: Deleting interface #3 eth1, 192.168.1.6#123, interface stats: received=135, sent=135, dropped=1, active_time=4197 secs
Mar 28 10:10:37 localhost ntpd[1442]: 149.156.70.60 interface 192.168.1.6 -> (none)
Mar 28 10:10:37 localhost ntpd[1442]: 149.156.24.40 interface 192.168.1.6 -> (none)
Mar 28 10:10:37 localhost ntpd[1442]: 46.250.172.2 interface 192.168.1.6 -> (none)
Mar 28 10:10:37 localhost ntpd[1442]: peers refreshed
Mar 28 10:10:38 localhost su[4624]: (to root) root on none
Mar 28 10:10:38 localhost su[4624]: pam_unix(su:session): session opened for user root by (uid=0)
Mar 28 10:10:38 localhost laptop-mode[4653]: Laptop mode
Mar 28 10:10:38 localhost laptop-mode[4654]: enabled, active [unchanged]
Mar 28 10:10:38 localhost dhcpcd[1435]: eth1: carrier acquired
Mar 28 10:10:38 localhost dhcpcd[1435]: eth1: sending IPv6 Router Solicitation
Mar 28 10:10:38 localhost dhcpcd[1435]: eth1: rebinding lease of 192.168.1.6
Mar 28 10:10:38 localhost dhcpcd[1435]: eth1: acknowledged 192.168.1.6 from 192.168.1.1 `TP-LINK'
Mar 28 10:10:38 localhost dhcpcd[1435]: eth1: checking for 192.168.1.6
Mar 28 10:10:38 localhost su[4624]: pam_unix(su:session): session closed for user root
Mar 28 10:10:38 localhost su[4660]: (to root) root on none
Mar 28 10:10:38 localhost su[4660]: pam_unix(su:session): session opened for user root by (uid=0)
Mar 28 10:10:38 localhost su[4660]: pam_unix(su:session): session closed for user root
Mar 28 10:10:38 localhost kernel: EXT4-fs (sda6): re-mounted. Opts: commit=0
Mar 28 10:10:38 localhost kernel: EXT4-fs (sda7): re-mounted. Opts: commit=0
Mar 28 10:10:38 localhost laptop-mode[4694]: Laptop mode
Mar 28 10:10:38 localhost laptop-mode[4695]: enabled, active [unchanged]
Mar 28 10:10:38 localhost logger[4698]: ACPI action undefined: ACPI0003:00
Mar 28 10:10:38 localhost slim[806]: tint2 : invalid option "task_margin",
Mar 28 10:10:38 localhost slim[806]: upgrade tint2 or correct your config file
Mar 28 10:10:38 localhost slim[806]: tint2 : nb monitor 1, nb monitor used 1, nb desktop 1
Mar 28 10:10:38 localhost slim[806]: X Error of failed request: BadWindow (invalid Window parameter)
Mar 28 10:10:38 localhost slim[806]: Major opcode of failed request: 21 (X_ListProperties)
Mar 28 10:10:38 localhost slim[806]: Resource id in failed request: 0x18000b0
Mar 28 10:10:38 localhost slim[806]: Serial number of failed request: 12
Mar 28 10:10:38 localhost slim[806]: Current serial number in output stream: 12
Mar 28 10:10:40 localhost slim[806]: you have no weather alerts
Mar 28 10:10:40 localhost slim[806]: processing complete
Mar 28 10:10:40 localhost slim[806]: gathering data with curl
Mar 28 10:10:40 localhost slim[806]: % Total % Received % Xferd Average Speed Time Time Time Current
Mar 28 10:10:40 localhost slim[806]: Dload Upload Total Spent Left Speed
Mar 28 10:10:40 localhost slim[806]: 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0curl: (6) Could not resolve host: (nil); Unknown error
Mar 28 10:10:40 localhost slim[806]: not checking for alerts
Mar 28 10:10:40 localhost slim[806]: curl attempt timed out, trying again
Mar 28 10:10:40 localhost slim[806]: % Total % Received % Xferd Average Speed Time Time Time Current
Mar 28 10:10:40 localhost slim[806]: Dload Upload Total Spent Left Speed
Mar 28 10:10:40 localhost slim[806]: 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0curl: (6) Could not resolve host: (nil); Unknown error
Mar 28 10:10:42 localhost dhcpcd[1435]: eth1: sending IPv6 Router Solicitation
Mar 28 10:10:43 localhost dhcpcd[1435]: eth1: leased 192.168.1.6 for 259200 seconds
Mar 28 10:10:45 dhcppc4 ntpd[1442]: Listen normally on 6 eth1 192.168.1.6 UDP 123
Mar 28 10:10:45 dhcppc4 ntpd[1442]: peers refreshed
Mar 28 10:10:45 dhcppc4 ntpd[1442]: new interface(s) found: waking up resolver
Mar 28 10:10:45 dhcppc4 slim[806]: Traceback (most recent call last):
Mar 28 10:10:45 dhcppc4 slim[806]: File "/home/rlk120/.scripts/gmail.py", line 9, in <module>
Mar 28 10:10:45 dhcppc4 slim[806]: msg=temp.read()
Mar 28 10:10:45 dhcppc4 slim[806]: File "/usr/lib/python3.3/encodings/ascii.py", line 26, in decode
Mar 28 10:10:45 dhcppc4 slim[806]: return codecs.ascii_decode(input, self.errors)[0]
Mar 28 10:10:45 dhcppc4 slim[806]: UnicodeDecodeError: 'ascii' codec can't decode byte 0xc5 in position 375: ordinal not in range(128)
Mar 28 10:10:45 dhcppc4 slim[806]: not checking for alerts
Mar 28 10:10:45 dhcppc4 slim[806]: curl attempt timed out, trying again
Mar 28 10:10:45 dhcppc4 slim[806]: % Total % Received % Xferd Average Speed Time Time Time Current
Mar 28 10:10:45 dhcppc4 slim[806]: Dload Upload Total Spent Left Speed
Mar 28 10:10:46 dhcppc4 slim[806]: [234B blob data]
Mar 28 10:10:46 dhcppc4 dhcpcd[1435]: eth1: sending IPv6 Router Solicitation
Mar 28 10:10:50 dhcppc4 dhcpcd[1435]: eth1: sending IPv6 Router Solicitation
Mar 28 10:10:50 dhcppc4 dhcpcd[1435]: eth1: no IPv6 Routers available
Mar 28 10:11:03 dhcppc4 slim[806]: No protocol specified
Mar 28 10:11:03 dhcppc4 slim[806]: (chromium:4750): Gtk-WARNING **: cannot open display: :0.0
Mar 28 10:11:31 dhcppc4 systemd-logind[796]: System is rebooting.
Mar 28 10:11:32 dhcppc4 systemd[1]: Deactivating swap /dev/sda8...
Mar 28 10:11:32 dhcppc4 systemd[1]: Deactivating swap /dev/sda8...
Mar 28 10:11:32 dhcppc4 systemd[1]: Deactivating swap /dev/sda8...
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Sound Card.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopped target Sound Card.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Daemon for power management...
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Authorization Manager...
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Graphical Interface.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopped target Graphical Interface.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Multi-User.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopped target Multi-User.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping ACPI event daemon...
Mar 28 10:11:32 dhcppc4 ntpd[1442]: ntpd exiting on signal 15
Mar 28 10:11:32 dhcppc4 acpid[793]: exiting
Mar 28 10:11:32 dhcppc4 dhcpcd[4810]: sending signal 1 to pid 1435
Mar 28 10:11:32 dhcppc4 dhcpcd[4810]: waiting for pid 1435 to exit
Mar 28 10:11:32 dhcppc4 dhcpcd[1435]: received SIGHUP, releasing
Mar 28 10:11:32 dhcppc4 dhcpcd[1435]: eth1: releasing lease of 192.168.1.6
Mar 28 10:11:32 dhcppc4 dhcpcd[1435]: eth1: removing interface
Mar 28 10:11:33 dhcppc4 slim[806]: Conky: received SIGHUP or SIGUSR1. reloading the config file.
Mar 28 10:11:33 dhcppc4 slim[806]: XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0.0"
Mar 28 10:11:33 dhcppc4 slim[806]: after 200200 requests (200197 known processed) with 0 events remaining.
Mar 28 10:11:33 dhcppc4 slim[806]: Conky: received SIGHUP or SIGUSR1. reloading the config file.
Mar 28 10:11:33 dhcppc4 slim[806]: XIO: fatal IO error 4 (Interrupted system call) on X server ":0.0"
Mar 28 10:11:33 dhcppc4 slim[806]: after 226 requests (226 known processed) with 0 events remaining.
Mar 28 10:11:33 dhcppc4 slim[806]: real transparency off.... depth: 24
Mar 28 10:11:33 dhcppc4 slim[806]: xRandr: Found crtc's: 4
Mar 28 10:11:33 dhcppc4 slim[806]: xRandr: Linking output LVDS with crtc 0
Mar 28 10:11:33 dhcppc4 slim[806]: real transparency off.... depth: 24
Mar 28 10:11:33 dhcppc4 slim[806]: xRandr: Found crtc's: 4
Mar 28 10:11:33 dhcppc4 slim[806]: xRandr: Linking output LVDS with crtc 0
Mar 28 10:11:33 dhcppc4 slim[806]: XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0.0"
Mar 28 10:11:33 dhcppc4 slim[806]: after 534585 requests (534585 known processed) with 0 events remaining.
Mar 28 10:11:33 dhcppc4 slim[806]: XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0.0"
Mar 28 10:11:33 dhcppc4 slim[806]: after 163909 requests (163909 known processed) with 0 events remaining.
Mar 28 10:11:33 dhcppc4 slim[806]: you have no weather alerts
Mar 28 10:11:33 dhcppc4 slim[806]: processing complete
Mar 28 10:11:33 dhcppc4 kernel: cfg80211: Calling CRDA to update world regulatory domain
Mar 28 10:11:33 dhcppc4 kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Mar 28 10:11:33 dhcppc4 netcfg-daemon[4777]: :: siec_domowa down [done]
Mar 28 10:11:33 dhcppc4 slim[806]: Server terminated successfully (0). Closing log file.
Mar 28 10:11:33 dhcppc4 laptop-mode[4865]: Laptop mode
Mar 28 10:11:33 dhcppc4 laptop-mode[4866]: enabled, active [unchanged]
Mar 28 10:11:34 dhcppc4 systemd[1]: slim.service: main process exited, code=exited, status=1/FAILURE
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped SLiM Simple Login Manager.
Mar 28 10:11:34 dhcppc4 systemd[1]: Unit slim.service entered failed state
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Permit User Sessions...
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Permit User Sessions.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Basic System.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped target Basic System.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Dispatch Password Requests to Console Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Dispatch Password Requests to Console Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Forward Password Requests to Wall Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Forward Password Requests to Wall Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Daily Cleanup of Temporary Directories.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Daily Cleanup of Temporary Directories.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Sockets.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped target Sockets.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping LVM2 metadata daemon socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed LVM2 metadata daemon socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Device-mapper event daemon FIFOs.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed Device-mapper event daemon FIFOs.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Syslog Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed Syslog Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping ACPID Listen Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed ACPID Listen Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping D-Bus System Message Bus Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed D-Bus System Message Bus Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping System Initialization.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped target System Initialization.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Load Kernel Modules...
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Load Kernel Modules.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Apply Kernel Variables...
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Apply Kernel Variables.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Setup Virtual Console...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Setup Virtual Console.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Set Up Additional Binary Formats...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Set Up Additional Binary Formats.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Encrypted Volumes.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Encrypted Volumes.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Swap.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Swap.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Local File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Local File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounting /home...
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounting /tmp...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Remote File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Remote File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounted /tmp.
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounted /home.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Unmount All Filesystems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Unmount All Filesystems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Local File Systems (Pre).
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Local File Systems (Pre).
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Remount Root and Kernel File Systems...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Remount Root and Kernel File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Save Random Seed...
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Update UTMP about System Shutdown...
Mar 28 10:11:35 dhcppc4 systemd[1]: Started Save Random Seed.
Mar 28 10:11:35 dhcppc4 systemd[1]: Started Update UTMP about System Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Final Step.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Final Step.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Reboot...
Mar 28 10:11:35 dhcppc4 systemd[1]: Shutting down.
Mar 28 10:11:35 dhcppc4 systemd[1]: Hardware watchdog 'iTCO_wdt', version 0
Mar 28 10:11:35 dhcppc4 systemd[1]: Set hardware watchdog to 10min.
Mar 28 10:11:35 dhcppc4 kernel: watchdog watchdog0: watchdog did not stop!
Mar 28 10:11:35 dhcppc4 systemd-journal[131]: Journal stopped
Somebody probably find interesting things in this code.
And here is some fail slim:
# journalctl /usr/lib/systemd/systemd --since=today
-- Logs begin at Mon 2012-09-10 20:20:07 CEST, end at Thu 2013-03-28 10:37:18 CET. --
Mar 28 10:10:36 localhost systemd[1]: Time has been changed
Mar 28 10:10:36 localhost systemd[1]: systemd-tmpfiles-clean.timer: time change, recalculating next elapse.
Mar 28 10:10:36 localhost systemd[1]: Starting Daemon for power management...
Mar 28 10:10:36 localhost systemd[1]: Started Suspend.
Mar 28 10:10:36 localhost systemd[1]: Service sleep.target is not needed anymore. Stopping.
Mar 28 10:10:36 localhost systemd[1]: Stopping Sleep.
Mar 28 10:10:36 localhost systemd[1]: Stopped target Sleep.
Mar 28 10:10:36 localhost systemd[1]: Starting Suspend.
Mar 28 10:10:36 localhost systemd[1]: Reached target Suspend.
Mar 28 10:10:36 localhost systemd[1]: Started Daemon for power management.
Mar 28 10:11:32 dhcppc4 systemd[1]: Deactivating swap /dev/sda8...
Mar 28 10:11:32 dhcppc4 systemd[1]: Deactivating swap /dev/sda8...
Mar 28 10:11:32 dhcppc4 systemd[1]: Deactivating swap /dev/sda8...
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Sound Card.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopped target Sound Card.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Daemon for power management...
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Authorization Manager...
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Graphical Interface.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopped target Graphical Interface.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping Multi-User.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopped target Multi-User.
Mar 28 10:11:32 dhcppc4 systemd[1]: Stopping ACPI event daemon...
Mar 28 10:11:34 dhcppc4 systemd[1]: slim.service: main process exited, code=exited, status=1/FAILURE
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped SLiM Simple Login Manager.
Mar 28 10:11:34 dhcppc4 systemd[1]: Unit slim.service entered failed state
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Permit User Sessions...
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Permit User Sessions.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Basic System.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped target Basic System.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Dispatch Password Requests to Console Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Dispatch Password Requests to Console Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Forward Password Requests to Wall Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Forward Password Requests to Wall Directory Watch.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Daily Cleanup of Temporary Directories.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Daily Cleanup of Temporary Directories.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Sockets.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped target Sockets.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping LVM2 metadata daemon socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed LVM2 metadata daemon socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Device-mapper event daemon FIFOs.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed Device-mapper event daemon FIFOs.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Syslog Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed Syslog Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping ACPID Listen Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed ACPID Listen Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping D-Bus System Message Bus Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Closed D-Bus System Message Bus Socket.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping System Initialization.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped target System Initialization.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Load Kernel Modules...
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Load Kernel Modules.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Apply Kernel Variables...
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopped Apply Kernel Variables.
Mar 28 10:11:34 dhcppc4 systemd[1]: Stopping Setup Virtual Console...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Setup Virtual Console.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Set Up Additional Binary Formats...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Set Up Additional Binary Formats.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Encrypted Volumes.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Encrypted Volumes.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Swap.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Swap.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Local File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Local File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounting /home...
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounting /tmp...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Remote File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Remote File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounted /tmp.
Mar 28 10:11:35 dhcppc4 systemd[1]: Unmounted /home.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Unmount All Filesystems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Unmount All Filesystems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Local File Systems (Pre).
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Local File Systems (Pre).
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Remount Root and Kernel File Systems...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Remount Root and Kernel File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Save Random Seed...
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Update UTMP about System Shutdown...
Mar 28 10:11:35 dhcppc4 systemd[1]: Started Save Random Seed.
Mar 28 10:11:35 dhcppc4 systemd[1]: Started Update UTMP about System Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Final Step.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Final Step.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Reboot...
Mar 28 10:11:35 dhcppc4 systemd[1]: Shutting down.
Mar 28 10:11:35 dhcppc4 systemd[1]: Hardware watchdog 'iTCO_wdt', version 0
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Unmount All Filesystems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Local File Systems (Pre).
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped target Local File Systems (Pre).
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopping Remount Root and Kernel File Systems...
Mar 28 10:11:35 dhcppc4 systemd[1]: Stopped Remount Root and Kernel File Systems.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Save Random Seed...
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Update UTMP about System Shutdown...
Mar 28 10:11:35 dhcppc4 systemd[1]: Started Save Random Seed.
Mar 28 10:11:35 dhcppc4 systemd[1]: Started Update UTMP about System Shutdown.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Final Step.
Mar 28 10:11:35 dhcppc4 systemd[1]: Reached target Final Step.
Mar 28 10:11:35 dhcppc4 systemd[1]: Starting Reboot...
Mar 28 10:11:35 dhcppc4 systemd[1]: Shutting down.
Mar 28 10:11:35 dhcppc4 systemd[1]: Hardware watchdog 'iTCO_wdt', version 0
Mar 28 10:11:35 dhcppc4 systemd[1]: Set hardware watchdog to 10min.
Last edited by xorgx3 (2013-03-28 10:52:08)

Strange behavior on my network... Has my home system been compromised? A disgruntled employee (sysAdmin) could have full access...worried...

I have been experiencing a lot of strange behavior on my home network ever since a disgruntled employee was let go. He was a server admin and had root access to my home network - where I run my business. I am getting a ton of span now, my websites were all infected with xss hacks, and many of my accounts are blacklisted. I did a clean install and DoD erase pass on my hardware, but I still see a lot of errors and my hosts file and VMs look very odd. not to mention the extremely odd loops in my ifconfig... Any help?
Here is an output of 'ifconfig'
(FYI, I am a software dev, so feel free to speak the jargon and ask for specific things)
(I hid any identifying info with either xx or my:ma:ca:dd:re:ss or something like that)
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
    options=3<RXCSUM,TXCSUM>
    inet6 ::1 prefixlen 128
    inet 127.0.0.1 netmask 0xff000000
    inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
    nd6 options=1<PERFORMNUD>
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    options=10b<RXCSUM,TXCSUM,VLAN_HWTAGGING,AV>
    ether th:is:ad:dr:es:s1
    inet6 fxxx::xx2a:xxff:fxxx:fxxx%en0 prefixlen 64 scopeid 0x4
    inet 10.xx.xx.x netmask 0xffffff00 broadcast 10.xx.xx.xxx
    nd6 options=1<PERFORMNUD>
    media: autoselect (1000baseT <full-duplex,flow-control,energy-efficient-ethernet>)
    status: active
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    ether th:is:ad:dr:es:n1
    inet6 fe80::e2f8:47ff:fe29:6ec2%en1 prefixlen 64 scopeid 0x5
    inet 10.xx.xx.x netmask 0xffffff00 broadcast 10.xx.xx.xxx
    nd6 options=1<PERFORMNUD>
    media: autoselect
    status: active
fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078
    lladdr 70:cd:xx:ff:fe:xx:xx:xx
    nd6 options=1<PERFORMNUD>
    media: autoselect <full-duplex>
    status: inactive
en2: flags=8922<BROADCAST,SMART,PROMISC,SIMPLEX,MULTICAST> mtu 1500
    options=60<TSO4,TSO6>
    ether my:wi:fi:ma:ca:dd
    media: autoselect <full-duplex>
    status: inactive
bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    options=63<RXCSUM,TXCSUM,TSO4,TSO6>
    ether th:is:ad:dr:es:mtu
    Configuration:
        id 0:0:0:0:0:0 priority 0 hellotime 0 fwddelay 0
        maxage 0 holdcnt 0 proto stp maxaddr 100 timeout 1200
        root id 0:0:0:0:0:0 priority 0 ifcost 0 port 0
        ipfilter disabled flags 0x2
    nd6 options=1<PERFORMNUD>
    media: <unknown type>
    status: inactive
p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304
    ether th:is:ad:dr:es:p2p0
    media: autoselect
    status: inactive
vmnet1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    ether 00:50:56:c0:00:01
    inet 192.168.48.1 netmask 0xffffff00 broadcast 192.168.48.255
vmnet8: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    ether 00:50:56:c0:00:08
    inet 192.168.219.1 netmask 0xffffff00 broadcast 192.168.219.255
ppp0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1396
    inet my.ded.vpn.xx --> 192.xxx.xxx.xxx netmask 0xffffff00
nooooooo:~ cearnhart$ ifconfig
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
    options=3<RXCSUM,TXCSUM>
    inet6 ::1 prefixlen 128
    inet 127.0.0.1 netmask 0xff000000
    inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
    nd6 options=1<PERFORMNUD>
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    options=10b<RXCSUM,TXCSUM,VLAN_HWTAGGING,AV>
    ether th:is:ad:dr:es:s1
    inet6 xxx::xxxx:xxff:xxxx:fxx2%en0 prefixlen 64 scopeid 0x4
    inet 10.xx.xx.x netmask 0xffffff00 broadcast 10.x.x.xxx
    nd6 options=1<PERFORMNUD>
    media: autoselect (1000baseT <full-duplex,flow-control,energy-efficient-ethernet>)
    status: active
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    ether th:is:ad:dr:es:n1
    inet6 fxxx::xxf8:47ff:fxx:6xx%en1 prefixlen 64 scopeid 0x5
    inet 10.x.x.x netmask 0xffffff00 broadcast 10.x.x.xxx
    nd6 options=1<PERFORMNUD>
    media: autoselect
    status: active
fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078
    lladdr xx:xx:xx:ff:fe:xx:5f:xx
    nd6 options=1<PERFORMNUD>
    media: autoselect <full-duplex>
    status: inactive
en2: flags=8922<BROADCAST,SMART,PROMISC,SIMPLEX,MULTICAST> mtu 1500
    options=60<TSO4,TSO6>
    ether xx:00:1e:xx:xx:xx
    media: autoselect <full-duplex>
    status: inactive
bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    options=63<RXCSUM,TXCSUM,TSO4,TSO6>
    ether th:is:ad:dr:es:mtu
    Configuration:
        id 0:0:0:0:0:0 priority 0 hellotime 0 fwddelay 0
        maxage 0 holdcnt 0 proto stp maxaddr 100 timeout 1200
        root id 0:0:0:0:0:0 priority 0 ifcost 0 port 0
        ipfilter disabled flags 0x2
    nd6 options=1<PERFORMNUD>
    media: <unknown type>
    status: inactive
p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304
    ether th:is:ad:dr:es:p2p0
    media: autoselect
    status: inactive
vmnet1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    ether 00:50:56:c0:00:01
    inet 192.168.48.1 netmask 0xffffff00 broadcast 192.168.48.255
vmnet8: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    ether 00:50:56:c0:00:08
    inet 192.168.219.1 netmask 0xffffff00 broadcast 192.168.219.255

If you know or suspect that a hostile intruder has either had physical access to it, or has been able to log in remotely, then there are some steps you should take to make sure that the computer is safe to use.
First, depending on the circumstances, computer tampering may be a crime, a civil wrong, or both. If there's any chance that the matter will be the subject of legal action, then you should do nothing at all without consulting a lawyer or the police. The computer would be the principal evidence in such a case, and you don't want to contaminate that evidence.
Running any kind of "anti-virus" software is pointless. If I broke into a system and wanted to leave a back door, I could do it in a way that would be undetectable by those means—and I don't pretend to any special skill as a hacker. You have to assume that any intruder can do the same. Commercial keylogging software—which has legitimate as well as illegitimate uses—won't be recognized as malware, because it's not malware.
The only way you can be sure that the computer is not compromised is to erase at least the startup volume and restore it to something like the status quo ante. The easiest approach is to recover the entire system from a backup that predates the attack. Obviously, that's only practical if you know when the attack took place, and it was recent, and you have such a backup. You will lose all changes to data, such as email, that were made after the time of the snapshot. Some of those changes can be restored from a later backup.
If you don't know when the attack happened, or if it was too long ago for a complete rollback to be feasible, then you should erase and install OS X. If you don't already have at least two complete, independent backups of all data, then you must make them first. One backup is not enough to be safe.
When you restart after the installation, you'll be prompted to go through the initial setup process for a new computer. That’s when you transfer the data from a backup in Setup Assistant.
Select only users in the Setup Assistant dialog—not Applications, Other files and folders, or Computer & Network Settings. Don't transfer the Guest account, if it was enabled.
Reinstall third-party software from original media or fresh downloads—not from a backup, which may be contaminated.
Unless you were the target of an improbably sophisticated attack, this procedure will leave you with a clean system. If you have reason to think that you were the target of a sophisticated attack, then you need expert help.
That being done, change all Internet passwords and check all financial accounts for unauthorized transactions. Do this after the system has been secured, not before.

IMac mouse problems / strange behavior (impossible to configure mouse preferences)

I work in a design and communication school, the used hardware is iMac (Intel) whit Lion (OS X 10.7), we have several rooms equipped with these Macs where students light up their data on the server.
Today, 3 of these Macs had problems with the mouse, including mine.
Basically the clicks don´t work correctly. We cant close windows, open folders or change some options by clicking, but we can open softwares, scroll.
In safari if i search something, when I try to click the link i want, safari opens a new tab instead the one i am at, and has other strange behaviors. So I´ve tried to change the mouse settings, and when i make a change, for example: change the scroll button to "buttun 3" the mouse automatically assumes all buttons to dashboard, but not at the configurations window because it says that scrool button still "button 3", when i use the click or the scroll or any button it just slid me to dashboard or a setting that has nothing to do with my option.
This is really causing a big problem since we are a school.. I already tried to change the mouse, clean, try another usb ports, search for update or restart but it still doing the same.
I think it have something to do with an update.. but not sure.. would be really gratefull if someone knows how to solve this.
As a temporary solution,i disabled all options using only the mouse click, but to do it, i had to plug in my tablet (that works perfectly for the record) and use it instead of mouse (since it was impossible to use it), than went to mouse preferences and disable left click, scroll and side buttons and then restart the Mac (or else it wont work)..
it will work fine but still a problem cause I use all mouse buttons custom as well as the students...

I have been experiencing a freezing mouse as well. I updated the mouse drivers but it is still happening. I have been repairing the permissions and noticed something very strange see the mention of a -t. I have been running unix systems since 1984 and have never seen that before....
Determining correct file permissions.
Permissions differ on ./Library, should be drwxrwxr-t , they are drwxrwxr-x
Owner and group corrected on ./Library
Permissions corrected on ./Library
Permissions differ on ./private/var/log/secure.log, should be -rw------- , they are -rw-r-----
Owner and group corrected on ./private/var/log/secure.log
Permissions corrected on ./private/var/log/secure.log
Permissions repair complete
Permissions differ on ., should be drwxrwxr-t , they are drwxr-xr-x
Owner and group corrected on .
Permissions corrected on .
The privileges have been verified or repaired on the selected volume
I reported this to Apple and they told me to erase the hard drive reinstall the
system. I really don't want to have to do that. It seems like something is taking
control of the machine.....

Strange behavior while plugged in

Hi,
my X1 compact shows a strange behavior since yesterday:
I plugged it in via the USB port for charging, and it started doing crazy things. Screen brightness went flashing from low to high and back, the touchscreen showed slow or no response to pushing buttons, everything got laggy as if some kind of process was running in the background with no end. When I unplug it, it basically works normally. But - from this time on, I couldn't charge it anymore, as the charge went down instead of up when plugged in! I tried a factory reset several times (power + volume up for 3 seconds), and although it did reset, the charging problem remained. I left it turned off for one night while plugged in, and in the morning, it was just charged to 25% with the charge going down rapidly in the first couple of minutes (after 5 minutes to 11%). Now it's at 1%, but I can use it for quite a while, indicating that the displayed charge certainly isn't correct.
When I plug it in, the same things happen again and again. When plugged in, I can't even enter the PIN correctly, because touchscreen input is somehow recognized falsely.
What could that be, what could I do??
Aleks

I'd like to, but... now it's gone from 1% to dead, and I can't bring it back to life, whether plugged in or not!
When it's plugged in, the red charging light doesn't even come up. When I hard reset it, it just vibrates as it should, but no charging light whatsoever. When I unplug it and try to start it, the red light just flashes three times.
Now I'll just try to leave it plugged in for some time, in hope that there will be enough charge to try to boot into safe mode.
But to me, it seems like some kind of hardware bug? I mean, it seems like the same problen bothers the phone even when it's shut down, so I wouldn't gess it's a problem with the apps or the system! But I just don't get why it worked all the time and then just suddenly this thing happens! I've had it now for 6 weeks, and I already had a similar problem on the second day already, but it went away with a hard reset while charging... after that, perfect charging and good battery life for 6 weeks!
Regards,
Aleks

Strange behavior when "trying" to burn a disk.

At least I think this is strange behavior, following the instructions in the help viewer, topic "Backing up your music to a CD or DVD." One thing for sure, it's not burning a disc and it ain't telling me why.
I select the playlist and click "Burn Disc"
Requests a blank disc. I insert one.
Message "checking media"
after about a minute, the disc ejects
Message "checking media" displays another 30 seconds
No other messages displayed.
What the ??? Shouldn't it at least display an error message??
Super-Drive information..... from System Profiler
MATSHITA DVD-R UJ-845C:
Firmware Revision: DPP9
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 2048 KB
Reads DVD: Yes
CD-Write: -R, -RW
DVD-Write: -R, -RW, +R, +RW
Burn Underrun Protection CD: Yes
Burn Underrun Protection DVD: Yes
Write Strategies: CD-TAO, CD-SAO, DVD-DAO
Media: No
Using Sony DVD+R discs.
Mac Mini Mac OS X (10.4.8)

Whoops, sorry, this was while burning a playlist.
I've also tried some Pleomax CD disks (Samsung), with no luck. I've tried burning directly from iTunes, and from Toast 7.
Of the types I've tried, the Sony DVD's have been the best for me. Haven't tried many types though. Maybe I can get disks one at a time until I find a brand my burner likes.
Still, isn't it strange that there is NO error message? It just quits?
Mac Mini Mac OS X (10.4.8)

Strange Behavior with gMSA in Server 2012 R2

Greetings,
I have been doing some testing with gMSA Accounts in a Server 2012 R2 environment (two separate environments, actually), and I have noticed something very strange that occurred in both environments, which does not appear to be occurring in one of our customer's
self-managed environments.
We created a Group Managed Service Account using the following article:
http://blogs.technet.com/b/askpfeplat/archive/2012/12/17/windows-server-2012-group-managed-service-accounts.aspx
Everything went smoothly, and the account installs/tests successfully on both of the hosts that we are testing on. I am able to set my services to run under the account, and most of them appear to work fine. I am having some issues with a few of my services,
and I believe that the strange behavior I am seeing may have something to do with this - described below:
As soon as I set the service's Log On Account (via the Log On Tab under the Service's Properties), the entirety of the "Log On" tab changes to "greyed out," and I am unable to change the Log On account back via the GUI (Screenshot
attached).
I found that I am able to successfully change the account via Command Line using sc.exe, but the Log On tab remains greyed out! So far, I have found nothing to remedy this, but confirmed that it happens for any service I set to use the gMSA as the Logon
Account, and that it happens in 2 separate test environments, but not in a Customer's production environment - very strange.
All servers in this environment are running Server 2012 R2, and domain Functional Level is currently Server 2012.
I have been unable to find any information online about this behavior, so I am hoping someone has seen this before, and can explain why this is happening.
Nick

VIvian,
Yes, we used the Install-AdServiceAccount gMSA command on each host using the gMSA account, and then ran Test-AdServiceAccount gMSA, which returned "True."
However, one thing I noticed is that if I run Test-ADServiceAccount gMSA as a Local Administrator, it fails with the following:
PS C:\Users\Administrator> Test-AdServiceAccount gMSA$
Test-AdServiceAccount : The server has rejected the client credentials.
At line:1 char:1
+ Test-AdServiceAccount gMSA$
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo          : SecurityError: (:) [Test-ADServiceAccount], AuthenticationException
    + FullyQualifiedErrorId : ActiveDirectoryCmdlet:System.Security.Authentication.AuthenticationException,Microsoft.A
   ctiveDirectory.Management.Commands.TestADServiceAccount
If I run Test-ADServiceAccount gMSA as Domain Administrator, it returns true:
PS C:\Users\Administrator.<domainname>> Test-AdServiceAccount gMSA$
True
Is this normal?
Overall, I think the issue I am running into is at the Application Level, and not a problem with the gMSA, as it appears to be working. (Can Start/Stop services without any issues). I will be investigating my issue further with 3rd-party vendors, unless
you think there is something wrong with my gMSA accounts based on the information I have provided.
Nick

Strange Behavior from iTunes 7.2

Running itunes - 7.2Recently had my itunes library “corrupted” or non functional.
Spent a long, long time rebuilding the library (see below) and noticed some strange behavior that has me terrified that itunes is corrupted and I am going to loose all the hard work, etc..
1. I have about 100 GB of music in various formats (apple protected/itunes store, mp3 (128 to 320), apple lossless, wav) and when I tried to rebuild the library by clicking on add to library it only added about 65 GB of the 100 GB. I had to go through and figure out what was missing and manually choose the specific folder when I added it.
Major pain and very time consuming.
So it is not adding songs correctly, but through way too much effort able to work around this.
2. About ½ of the itunes store tunes I purchased are no longer apple protected format. Somehow they were converted to mp3 at 192kbs. Some of the songs play fine others are now not as crisp and make a poping sound or skip. How could this happen? Are these files corrupted? Will I loose them?
3. At the top center of itunes the information bar, where the read out is for what song is playing and how much time has elapsed in the song, is not working. When I click on a song it starts playing but the elapsed time bar and counter never move, and when the next song starts playing the information never changes. It is stuck on what ever song you initiate play with by clicking on it and the information stays frozen.
4. itunes randomly stops playing at the end of a song….If listening to an album it is usually after three or four songs and when listening to a play list it is usually after one song.
I am afraid itunes is corrupted and will not function correctly and I am going to loose the hard work I put in trying to recover from the last crash.
Any suggestions??
Can’t wait for time machine. I hope it works as advertised. If so I could just go back in time to the last time iTunes worked correctly and go from there.

First of all I hope that you have a good b/u of all your tunes - either on ext HD or on DVD. Don't forget to b/u the iTunes Library and .xml files at the same time.
Have you tried to reinstall iTunes? Drag the app to the trash and remove the iTunesX.pkg from HD>Library>Receipts>iTunesX.pkg. Using a fresh .dmg of iTunes 7.2 reinstall.
Have you repaired permissions with Disk Utility?
Is your Quicktime up to date? At least version v7.1.5.
MJ

My iPods sound is iffy, for lack of a better word. At times it's fine, but most the time it doesn't work. The volume dials don't show up either. What's wrong with it and how should I fix it?

My friend said the speakers might be blown, but the sound still works at times. And I'm sure if he speakers were broken then the volume dials would show up as well. So I need help figuring out whys going on.

- Try cleaning out/blowing out the headphone jack. Try inserting/removing the plug a dozen times or so.
Try the following to rule out a software problem
- Reset the iPod. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup
- Restore to factory settings/new iPod.
- Make an appointment at the Genius Bar of an Apple store. Seems you have a bad headphone jack or other hardware problem.
Apple Retail Store - Genius Bar
If not under warranty Apple will exchange your iPod for a refurbished one for this price. They do not fix yours.
Apple - iPod Repair price
A third-party place like the following will replace the jack for less. Google for more.
iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
Replace the jack yourself
iPod Touch Repair – iFixit

Strange behavior - icon thumbnail instead of image - CC@OSX10.10

Hi,
my CC (@OS X 10.10.3) showing a strange behavior using vanishing point filter.
After defining grid and try to paste the image OS X paste the icon thumbnail instead of the image,
Many thanks in advance!!
br
Joachim

It is probably related to the fact that you are setting the tables row height in the renderer this will fire a render message when the height changes. One height is applied to all rows of a table. This means that is you have images of different heights you are continually changing the tables row height and therefore continually rendereing.
My approach would be to have all the images fit into a set size ( say 64*64 ( with scaling if neccesary ) you could then have a popup show the full size image if required.

Strange behavior in report Output

Hi,
Strange behavior in report output , please some one help me out of this problem.
I am using Oracle order capture rdf file ASOPQTEL.rdf.
My working environment:
Windows,apps instance .Now this rdf file is working fine in my work Environment.
when this same file is deployed in client environment (UNIX and different apps instance from my working environment apps instance)
for some cases it is giving output.
for some cases it's throughing error.
Thanks,
Mithun

Please specify what kind of error you are getting and what is command you are firing on Unix.

Strange behavior of the Macbook pro display

Hi to all
I'm using my MacBook pro, and notice some strange behavior after open several windows or applications, I don't know how to explain, so here is a photo:
http://www.flickr.com/photos/86155326@N00/
I have tried: go back to 10.4.6 / create a new account / Hardware test... and Nothing.
Any suggestions?
Pedro

I am having the exact same problem(and no one is replying to my post either), I read in another post of someone who had a somewhat similar issue and someone commented that it was bad VRAM and warranted the logic board to be replaced. I'm hoping this is not the case, or at least hoping the problem does not get worse because I am in school and can't be without this computer for 2 weeks while it gets repaired..I'm hoping I can last til the holidays...
pictures of my problem:
http://www.rpi.edu/~neala/pics/display/Messed%20up%20desktop.png
http://www.rpi.edu/~neala/pics/display/Picture%204.png
Sometimes I can make it go away by moving windows, and sometimes that makes it worse... this computer is only 100 days old...come on apple..help us out!

Report FP_TEST_00 - Strange behavior

Hello Gurus,
A strange behavior with report FP_TEST_00 occurs:
SA38 --> FP_TEST_00 --> select a device --> execute --> print preview then and error or popup is show:
Adobe Reader
Error initializing the font server module
Then the SAP GUI is closed, I check the ST22 and no dump is generated and in transaction SM21 only appear:
DP Q0 4 Connection to user 551 (ADMIN ), terminal 86 (HUSVP-SAP-BA) lost
DP Q0 I Operating system call recv failed (error no. 232 )
The #1 log entry: *
Details Page 2 Line 28 System Log: Local Analysis of sapdev                   1
Time     Type Nr Clt User TCode Grp N Text
11:37:20 DP                     Q0 4 Connection to user 551 (ADMIN ), terminal 86 (HUSVP-SAP-BA) lost
Connection to user 551 (ADMIN ), terminal 86 (HUSVP-SAP-BA) lost
Details
Recording at local and central time........................ 25.02.2010 11:37:20
Task...... Process    User...... Terminal Session TCode Program Cl Problem cl         Package
11092      Dispatcher                                           K SAP Web AS Problem STSK
Further details for this message type
Module nam Line Error text..........              Caller.... Reason/cal
dpxxdisp   1223 551 ADMIN       86 HUSVP-SAP-BA DpRTmPr    NiBufRe
Documentation for system log message Q0 4 :
The SAP Dispatcher (part of the application server) has lost the
connection to a terminal process. For example, this happens when the
terminal program (GUI) terminates without correctly logging off the
application server. More detailed information about the error
context is not available here.
Technical details
File Offset RecFm System log type             Grp N variable message data
   21 254340 m     Error (Function,Module,Row) Q0 4 551 ADMIN       86 HUSVP-SAP-BA     DpRTmPrNiBufRedpxxdisp1223
The #2 Log show: *
Details Page 2 Line 29 System Log: Local Analysis of sapdev                   1
Time     Type Nr Clt User TCode Grp N Text
11:37:20 DP                     Q0 I Operating system call recv failed (error no. 232 )
Operating system call recv failed (error no. 232 )
Details
Recording at local and central time........................ 25.02.2010 11:37:20
Task...... Process    User...... Terminal Session TCode Program Cl Problem cl         Package
11092      Dispatcher                                           K SAP Web AS Problem STSK
Further details for this message type
Module nam Line Error text        Caller.... Reason/cal
nixxi.cp   4435           recv232 NiIRead    recv
Documentation for system log message Q0 I :
The specified operating system call was returned with an error.
For communication calls (receive, send, etc) often the cause of errors
are network problems.
It could also be a configuration problem at operating system level.
(file cannot be opened, no space in the file system etc.).
Additional specifications for error number 232
Name for errno number ECONNRESET
No documentation available for error ECONNRESET
Technical details
File Offset RecFm System log type             Grp N variable message data
21 254520 m     Error (Function,Module,Row) Q0 I           recv232                     NiIReadrecv   nixxi.cp4435
Edited by: Hernando Polania Cadena on Feb 25, 2010 8:36 PM

Hello All,
I applied the solution in page
http://wiki.sdn.sap.com/wiki/display/PLM/Adobe%209%20-%20SAPGUI%20crash
Works OK
Thanks
Hernando

Strange behavior when I try to match a mpeg2 video with the menu size image

hello all,
got a strange behavior when I try to match a mpeg2 video with the menu size image,
menu size is 1920 x 1080 (photoshop file)
mpeg2 video 1920 x 1080 (1second 19 frames)
the idea is to go from the menu link to the next sub menu with a video as transition, using the same image on the video as the menu and then zooming in (in my case through a door) to end up after the zoom in the next level menu.
I try to achieve a smooth change from the first play menu picture to the video image into the next level menu picture,
everything works good but when I watch it on the preview mode on the left and right side of the video it shows a black bar at least 15 to 25 pixel wide, that means the video image appears smaller and it causes a little jump what is preety disturbing and can not be sold as a professional work.
why encore treats the video size and picture differently?
it's gratful appreciated if somebody who got experience in a transition I mentioned obove posting any solution,
thankl you all

Hi all
I'm having a very similar problem with Encore. My menu items are distorting (a minor but infuriating squashing top and bottom) when previewed.
Using Encore,PS,AE CS4
DVD format SD PAL DV widescreen
I created 3 menu frameworks and 3 video transistions to link them in AE. On the final frame of each transistion in AE I saved the frame with Composition>Save Frame to> Photoshop Layers. In PS i added the button functionality and saved.
In Encore I use Dynamic link to import AE transistions as timelines and imported each PS menu twice, once as "menu" and once as an asset.
When I link the timeline transistions to the menu and preview at the point the menu begins the whole image is squashed. When the next transistion is activated the image returns to its original size.
Thinking it was the use of PS that was causing the menus to distort I used the menu asset directly in the time line. Obviously no menu functionality but also no distortion. The AE transistion flowed straight into the "menu" just as I expected.
In the properties panel the menu Aspect Ratio 16:9
The AE transistions PAR is SD PALwidescreen 1.4587.
I did try the Blu Ray suggestion above but the same distortion was apparent.
Any suggestions short of squashing the video to match the menu would be welcomed.
Thanks

Re: Sattelite M305D-S4830 Volume Dial Strange Behavior

Similar Messages

Maybe you are looking for