Re: "There is no supported audio device available"

Thanks for both the comments. I had looked all through the various BIOS settings, but hadn't gone into the OC area, because I'm not over-clocked. When my wife gets off her computer, I'll go into the BIOS and take a look at the Execute Disable Bit setti...

Just... why resurrect old topic? Open new thread if you require help.
>>Please read and comply with the Forum Rules.<<

Similar Messages

E5 DAC/Amp Win8 error "There is no supported audio device available"

I've just received my Sb E5, and installed the software package (while the E5 was connected and charging) without "apparent" problems. However, if I start the software it will report a problem with reading the device, and if I use the menu and select "audio device selection" it will immediately report"
"There is no supported audio device available"
If I disconnect, the software's volume indicator will max, and then if I reconnect USB the volume will return to ~15%.
Please advise ...
TIA

Have you installed all of the drivers:
http://www.msi.com/product/mb/Z77A-G45.html#/?div=Driver&os=Win7%2064
I don't see anything about the Sound Blaster Cinema
http://www.msi.com/product/mb/Z77A-G45.html#/?div=Overview
Did you mean the z87-g45 gaming? http://www.msi.com/product/mb/Z87-G45-GAMING.html

"No supported audio device available" ?

Win7, Creative board is: sound blaster X-FI Extreme Gamer.
Creative Consule shows the subject message whenever i try to open it. The creative player would show the same message but i re-installed it and it works fine.
Trying re-install the driver gives the old "device not found" message. In device manager there are no problem devices found. It shows the creative card and 2 High definition audio devices as "Working".
These are the driver/programs I am presently running:
CMPlyr5_PCAPP_LB_5_25_02.exe
CSL_PCAPP_LB_2_6_09.exe
DDL_PCAPP_LB__3_00_-6.exe
DTS_PCAPP_LB__03_08.exe
SBXF_PCDRV_LB_2_8_003.exe
Under Sound (Playback) I have the Speakers, Creative SB-XFi set as the default.
For recording I have Digital-In Creative SB-XFI as the default.
The music/videos plays just fine using any player that i have.
Problem is: No supported audio device available. How do i correct this and have a working console?
thank you,
savagcl

I am no expert, but does it help by installing it with an admin account in windows?
(As opposed to any non-admin user accounts.)

Console Launcher No support Audio Device Available

Note: Creative SB X-fi is detected (without a yellow mark) in my device manger. My card is an X-fi Titanium Fatalty Professional.
The easiest way I can put this is by explaining the mistake I made. Without installing the card, I moved it from one PCI-e slot to another, the one below it. This caused a small annoying issue that I decided to fix by totally uninstalling the card (correctly I hope) and putting it back in it's original slot. After reinstalling it via the disk it came with, when the computer restarts afterwards I am told that no supported hardware is detected and most of what seems to have installed correctly doesn't even show in my programs.
I have tried uninstalling and driver sweeper for HOURS straight over and over and so far nothing is working. Has anyone had a similar issue or know what the problem is? I've already made sure I'm using the same settings I originally used before moving slots but no dice.
P.S. During SOME of the updates or even installations, I? occasionally receive the error I-00 (usually during Alchemy or Creative Control Console installations or Updates) and I am told the installation can't continue. It does though, simply bypassing these things/
I am using Windows 7 64bit

Update: I'm facing a new issue now during installation! -EVERY- time the install wizard finishes and I restart the computer, I see the volume panel icon on the task bar and Creative SB X-fi when I hover over it. However, when I double click to open the console launcher (Which installed correctly to my knowledge) I'm told no supported audio device is available.
Did I break my card or something after what I did earlier? Or is my disk screwed up now too? I'd really rather not use the motherboard's crappy audio, I can actually tell that the audio quality is lower.

No audio devices available in late-2013 iMac

Updated Mavericks to 10.9.1 yesterday.
Today there are no analog audio devices available for output. Airplay devices work normally.
I have reset PRAM, disconnected all peripherals etc. Have tried connecting audio devices to the 3.5mm output jack.
Any suggestions?
Thanks in advance.

This issue was resolved by re-installing 10.9 over 10.9.1.
Think I'll wait for 10.9.2 until I update again.

XtremeMusic and MediaSource 5 - NO supported audio device detected? HE

I have had my X-Fi xtrememusic card for over a year now. no problems with it so far. runs great. BUT i installed a new motherboard and new cpu, etc.
Now when I open mediasource player... and click on the SVM buttom or the AudioClean up button, the timescale, or cross fade buttons (essentially all of the buttons on the bottom) it gives me the Error: "This feature is not available because no supported Audio Device is detected."
Mind you, the sound works.. i can play back music, it works great. AND via the console I CAN enable the SVM and it DOES work... but it seems like the media source player doesn't "see" that i have the xtrememusic card?
I am running the latest and SAME drivers and applications (mediasource 5) as before. WinXP Pro service pack 3. THere are NO conflicts with any devices in device manager....
Can someone help? I tried reinstalled the application, and driver... still same issue. I really like the audio cleanup when i listen to my recorded lectures and it takes away the hiss...
Help?
Message Edited by bofeity on 0-5-2008 :55 AM

I noticed there was an?AuzenWDM .5 pack so I have tried that, but still the same problem none of the software will detect the audio device yet the driver installs fine.

"No Audio Device Available" - Vi

My uncle bought the external sound blaster assuming it would work with windows vista, since it says this on the box... however as it turns out the disc doesnt carry the correct drivers... anyway, i've downloaded and installed these onto his laptop, and they all appear in mmsys.cpl with the heading "working properly" ... however, when I try to open creative smart recorder i'm told there is no audio device available, and the creative diagnostic says that hardware has not been detected, despite the fact that it is plugged into a USB port and the power light on the SB box is on. Has anyone else had this problem and figured out how to solve it's I've tried different combinations of inputs and had no luck and am running out of ideas. Also, when I play cassettes from the hi-fi, plugged into the line in on the sound blaster, then plug headphones into the phones jack, there is no output from that either. Any possible help that can be offered is much appreciated?thanks - dan

I've recently had the same trouble and still haven't solved it.
I have the "li've 24" usb soundblaster which worked fine on my previous computer running on Windows XP home. When I connected it to a new PC using Vista 32 bits it "created" all manner of problems, all of which I eventually resolved apart from the inability to use the smart recorder. It gives an error message that it can't find a device, which is obviously stupid as everything else works. I have tried running this part of the application in Windows XP compatibility mode but it makes no difference. I have virtually given up trying unless someone out there knows of a solution. As things are, it's a real nuisance not having this facility.

Smart Recorder - Audigy 2 ZS - Win 7 - "no audio device available"

LSmart Recorder - Audigy 2 ZS - Win 7 - "no audio device available"nI've got Windows 7 Ultimate 64 bit and a Creative Audigy 2 ZS. They've worked fine together, but I recently tried to install the programs that come on the CD and I can't get Smart Recorder to work.
It has a message saying "There is no audio device available on the system. The application will now close."? I checked my control panel and it definitely shows a my Audigy 2.
I found an old post that suggested using the CTZAPXX.EXE on the CD, but it didn't do anything. I watched the CPU go to 50% usage, but nothing happened for minutes. (http://forums.creative.com/t5/Sound-Blaster/Speaker-settings/m-p/40229)
How can I fix this problem with Smart Recorder?
Thanks,
Mike

Is it time to upgrade to X-Fi or another brand?

AuzenWDM Pack 1.0 and "No supported audio device detected"

Hi there,
I installed the AuzenWDM pack and have the driver working properly, however when it comes to using the rest of the software in the pack none of it works, I get the same similar error of "No supported audio device" or similar. Now I know this driver pack works because thats what I used before reinstalling windows recently.
My specs are:
Win 7 64bit
AMD 4400+
4Gb DDR
A8N SLI Deluxe (nforce 4)
EDIT: It might help to tell you that i have an XFi Fatality (launch model with the front bay)
Any help with is would be appreciated?
Thanks

I noticed there was an?AuzenWDM .5 pack so I have tried that, but still the same problem none of the software will detect the audio device yet the driver installs fine.

Could not find supported audio device in AA3

okay so i know its not a good idea to use AA3 with Vista...but other people are doing it so why can't I? I've seen the topic posted before but the threads are pretty much dead and I still have no helpful info. I've scoured this thing with no affective solution. I've installed AA3 on several systems in the past and never had this much trouble--if any. This problem has gone on for over 2 months now!
Since I installed AA3 on my new computer all i can get and all i have ever gotten is the "AA could not find a supported audio device. Please check device settings" dialog--
press okay (or x) and Audition closes---never getting past the loading window --during "initalizing required components"
I have 3 audio devices/ with up to date drivers which all my other audio programs recognize (Audition 1.5, Sonor, Cubase + more) with no problem whatsoever--
AA3
Windows Vista SP1 64 bit
Realtek HD Audio
+ Presonus FP10 digital firewire interface/preamp (kind of unrelated but aa3 still wont recognize it either apparently)
I have installed all updates including the 64-bit SP1 fix for AA3.
I've read the Realtek HD issue solutions and made sure my drivers are fine.
IM DESPERATE----PLEASE!!!
I'm having a recording studio built right now & AA3 is my main DAW so this is rather dire.---All the other DAW's i've tried suck compared to AA3 (with the exception of stability). hehe AA3 is always crashing on me and yet i still prefer it over other DAW's.

I put the PreSonus StudiLive 16.4.2 plus Adobe Audition 3 setup instructions into a short write-up on my blog: Live Event Multitrack Audio Capture
Here is a photo showing how to set up the Firewire channels for input and output
I hope this helps:
Ron Fredericks
LectureMaker, LLC

TS1574 no audio is working on imac and no audio device available to choose from

I am receiving no audio out of my IMac and no option to choosing the internal speakers device. Any thoughts would be appreciated. Originally thought is might have been a virus but down loaded software and no fix to solution.
Thanks,

Take each of the following steps that you haven't already tried.
1. Start with the steps recommended in this support article.
2. If your model has an audio-out (headphone) port, and a red light is coming from it, the internal switch is stuck in the position for digital output. You may be able to free it by inserting and removing a mini-stereo jack of the proper size. Inserting any kind of tool in the port may cause damage that won't be covered by your warranty.
If there's no red light, the switch may still be stuck in the headphone position. Try to free it the same way.
3. Boot in safe mode. You don't have to log in; just reboot as usual when the login screen appears.
4. Reset the NVRAM.
5. Reset the SMC.
6. Reinstall OS X after backing up all data.
7. Make a "Genius" appointment at an Apple Store.

Final Windows XP32/XP64, Vista32/64 Compatible drivers for E-MU USB serie audio devices available

http://www.emu.com/support/vista.asp
Driver & Firmware update download link:
http://www.emu.com/support/files/dow...cy=&Platform=1
MAC drivers & firmware update:
http://www.emu.com/support/files/dow...cy=&Platform=2
jutapa

maiki wrote:
Jutapa wrote:
Hmm... maybe you didn't open the page(s) there before postinghere?
As stated there:
E-MU® 0202 / 0404 / Tracker Pre USB Web Install Package v1.3
Date: 2/1/2008
Size: 69.8 MB
------------------------------------------end quote-----------------
My reply:
What???? Why do you suppose I didn't open that page? If I didn't open that page, how could I have quoted from it?
As I quoted in my previous post, as you quoted in your reply above, the drivers on that page are listed as "Tracker Pre". (Excuse me, but I don't know how I could have known that it was described as such on that page, if I had not even opened that page? Strange assumption on your part, if I may say so!)
In any case, I asked you (or anyone who knows) what that designation "Tracker Pre" means. (Pre Beta?) That certainly does not sound like a final version. Especially considering that the driver of 4/23/2007 is also still listed on that page, it really does not look like the driver of 2/1/2008 is "final", full (non-beta) driver.
So, why does the title of this thread describe the driver at the linked page as being "Final"?
Please explain.
And please, do not make silly assumptions, that I did not visit a page, when it should be quite obvious that I had done just that. Thank you.
Message Edited by maiki on 02-26-200811:44 PM
LOL
Tracker Pre is just another audio interface model E-MU has recently prepared ...
jutapa

Adobe audition could not find a supported audio device. Please check your device settings.

After install adobe audition 3.0 version (Legency version downloaded from official website), it can't start normally, a dialog shows the information as title and the application shut down automatically after click OK button.

Well, that is pretty much expected if you are using a contemporary operating system. It's simply not compatible. Too much has changed.
Mylenium

How do I use 2 Core Audio devices at the same time in Logic w/out switching

Hello, I use the Aardvark Direct Mix usb3 as my audio interface for mic and guitar. I just upgraded to Logic Pro 7 today and was hoping someone could tell me how I could use the Built-in Audio Core Audio driver along with the Direct Mix USB Core Audio Driver at the same time without having to switch Core Audio Driver's and than rebooting Logic. It is very frustrating doing that as well as not being able to hear my Logic audio during playback/record mode when I am trying to record via the USB3. WHat can I do? Thanks! If ther are both core audio, why can I not just use both of them at the same time? Why must a switch back and forth? Thanks!
[email protected]

THanks everyone! awsome article! Thanks for posting it, nh!
The weird thing is, once I go up to the Menu and select Open Aggregate Device Editor in the AUDIO/MIDI setup utility and try to add a new Aggregate Device setup (step # 6 from the link), the only audio device available is the "Built-in Audio". What's weird is when I have the main Audio MIDI Setup utility open, every single drop-down menu/tab has the "Direct Mix USB 3 1.0.9.1" device right beneath the "Built-in Audio" option. To me that says that the core audio device is indeed recognized by my computer (obviously since I can record with it using Logic). Can anyone help me with this one? Any suggestions?
Not that it should matter but, the hardware audio interface that I am using is made by the no-longer-existant company once known as Aardvark. I actually had to purchase a third party Core Audio driver just to have it recognized by OS X.
This is the website where I purchased my audio driver :
http://www.usb-audio.com/
A little more on how this device and it's core audio driver function within Logic . . . (Hopefully this might clarify something I may be screwing up) . . .
I launch Logic with its default Built-in Audio which allows playback of audio from the app. I than go up to Audio Hardware and Drivers and than drop the flip down Driver menu down to the second option, "Direct Mix USB 3 1.0.9.1." Logic than prompts me that I should try to (re)launch Logic Pro to load the appropriate CoreAudio.. I do that. Now I am ready to record guitar through the Direct Mix USB3, I just can't hear anything (unless I use head phones as an output from the Direct Mix).
Anyway, you all probably already knew what I meant so explaining that was pointless. But my question is, if the Driver is obviously recognized by my comp in both the Audio MIDI Setup and in Logic, than why won't the Direct Mix device show up as a possibility for setting up an aggregate device? Any suggestions? Thanks!
Power Mac G5 Dual 2.7Ghz 4.5gigs of RAM Mac OS X (10.4.7)
Power Mac G5 Dual 2.7Ghz 2.5gigs of RAM Mac OS X (10.4)

Qosmio X770: 4 nVidia HD audio devices in device manager

So i have a few questions...
In my device manager i have [this (screenshot)|http://i.imgur.com/NfH5E7p.jpg].
So i have (!) 4 nvidia hd audio and 1 hd realtek audio.
I usually update my nvidia video driver and nvidia hd audio driver is updated every time with it.
But not long ago i decided to find any other updates to my drivers, cause bloody toshiba (we call it that way in Russia) is too lazy to support their laptops. And [found this:(realtek hd R2.70 codec driver )|http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=24&PFid=24&Level= 4&Conn=3&DownTypeID=3&GetDown=false].
Installed it, everything is working fine so far. It is for realtek alc269 (and also many other devices, but for us only alc269 matters) which is the real name of realtek hd audio device in x770 laptops (i checked in program aida64, previously known as everest).
So now i have [this (screenshot)|http://i.imgur.com/6HM5mLj.jpg]: version 6.0.1.6662 date 19.06.2012
The previous version that lazy toshiba was glad to provide us with - 6.0.1.6360 [(screenshot)|http://i.imgur.com/dUQiPA0.jpg]
So the questions are:
1. Why i have FOUR nvidia hd audio devices in device manager?
2. How can i make nvidia hd audio my primary audio device? Or maybe they are some kind of virtual devices or smth like that.
3. Do you think the idea of installing driver directly from realtek website was bad? There is a disclaimer on their site: To be sure you obtain the full features/customizations provided in your original audio product, please download the latest drivers from your system/motherboard manufacturer's website.
So i invite everyone to test this audio driver with me :)
And a few more things.
In one topic i found this info: moreover, myself and other users of this forum have overclocked their cards from 657/1300/1200 to 800/900/1600 and are very pleased with the results, so try not to overexaggerate
(it is a quote). So I will be happy if someone gives me link to some kind of manual about overclocking 560m gt from our beloved x770.
Also I found a lot of topics about nvidia drivers with angry customers. I don't remember when i first updated video drivers, but i've never had problems with them. When the situation changed? As far as i can understand in 2011 you could't install nvidia drivers directly from nvidia website.
P.S. sorry for my english, i'm from Russia. Also there is some russian on screenshots, hope it won't make your eyes bleed.

At first i want to "thank" moderator about renaming my topic. Original name was: realtek vs nvidia hd audio x770 + update r2.70 question. Where is 2.70 part in the current name? Ok.
Second. To Tonny: I'm not lame user, no need to explain me obvious things).
> {quote:title=Tonny wrote:}{quote}
> > How can i make nvidia hd audio my primary audio device?
> I dont understand why you want to make an device primary?
> What is the purpose for that?
>
> If you want you can set the sound devices as default device in Control Panel -> Sound -> Playback tab
> Click on the device and choose default.
If there is nvidia hd audio device and it's not some kind of virtual device or controller, i want to test it like primary audio device. Simple curiosity. I love flac etc.,
So I always try to improve sound. And alc269 we have in x770 is also installed in my ANCIENT asus eee pc, so it's very depressing. Also your advice about control panel - sound is not working, i think you know why... There's only speaker device working on realtek hd audio.
> {quote:title=Tonny wrote:}{quote}
> You can use the driver from Realtek since the sound chip is from Realtek.
Yep, of course, but it's my 5th laptop and also i have 2 netbooks (i'm speaking only about portative devices, not pc). I tried to update drivers manually numerous times on my previous devices, and I learned a lesson, that if you install new driver (not from you laptop/whatever support page, but directly from device manufacter's website ) and even if you are absolutely sure that driver is compatible with you device there can be problems. For example, as i've already said realtek alc269 is installed in my qosmio x770 and in my super old asus eee pc. And driver is the same.
Also realtek driver support page has disclaimer: To be sure you obtain the full features/customizations provided in your original audio product, please download the latest drivers from your system/motherboard manufacturer's website. (already was in op-post).
So I only tried to hear from those who has already installed r2.70 realtek update or maybe tested it some way. But the moderator made it impossible renaming the topic.

Re: "There is no supported audio device available"

Similar Messages

Maybe you are looking for