Re: TouchPad on Satellite L30 does not work anymore

Yesterday when I connected my Notebook L30 to a projector , the windows hanged and after that the Pointing Device on the Touch Pad isnt working, I tried to install Synaptics also but no gain from it.
Please Help me !

Hi there,
did you already tried the key combination FN-F9?? This key combination reactivates the touchpad in case of deactivation.
Otherwise, backup all you important data and recover your machine since it would be the last solution to make the touchpad working again.
Greets

Similar Messages

Satellite A100 does not work anymore

Hi,
I bought a broken laptop and when I boot it up, I get very little:
all i get is 2 blue lights and a couple of red ones above the keyboars for around 1 tenth of a second.
I was thinking of resetting the bios.
I disassembled it and could not feel any heat going to processor but the board must work as the wireless card switch lights up along with start key but no fans or nothing else.
please help

First of all, I wonder why you bought a broken machine when youre not able to fix it.
If youre not a technician then sell the machine and buy a working one because no one here would exactly could tell you what to do or how to fix it.
The only posts would be like: "send the machine to an service partner" or "change the mainboard" or "sell the machine" , "throw the machine into trash"
I would assume that the mainboard is defective and needs to be replaced. I already replaced some mainboards on toshibas and its not that easy like some people think. You need some experience and often its not only the mainboard which is faulty, sometimes there is more then you assume.
I hope you get it fixed. Good luck.
Greets
P.s.: If you need a helpful site for something you would like to do then check the following link: http://www.irisvista.com/tech/

Wifi adapter of Satellite M30 does not work anymore

During these last couple of days the wifi adapter in my Satellite M30 have had a way of dying once a day.
The first time I still had a light and I could see when I turned it on and off. When that didn't help to get it going again, I decided to reboot and the wifi died completely.
Later, when I did a scan for hardware changes in the Device Manager, the adapter popped back up in the list of devices again and worked just fine.
At least up until today. A couple of hours ago it died again for no obvious reason and now I simply cannot get it back at all.
I might mention that yesterday the light didn't come back on after I did that scan for hardware changes and got it to work again.
When I tried to update the drivers it keep telling me that the drivers are already up to date and now I don't know what to do.
Is this a hardware problem and what can I do about it?
This laptop was 4 years and well used just a few days ago btw, but it never been taken apart and I've never had to send it in for service.
I would appreciate any help I can get.
Christa

Hi there,
thats definetly a hardware problem and it can only be resolved by exchanging the wireless LAN card. You can check if it works under linux (just download some live-CD e.g. knoppix, and let the OS recognise the wifi card - if it wont recognise then its definetly broken).
You could also contact an Authorized Service Provider and ask them for a hardware checkup but I guess they will charge you for that.
You have the choice... :)
Greets

Satellite U400 - the webcam does not work anymore

Hello guys here is my sudden probloema!
About a year ago I purchased a laptop
TOSHIBA - Satellite U400
with s.o. WinVista 32bit and with integrated webcam chicony etc. ....
For a year, everything worked correctly, but for some days now, the webcam does not work anymore.
As soon as I try to open it, a message of management software cam that says "Webcam driver open fail, please restart or computer room"
I tried to do it all: aggioronato and downloaded the drivers from toshiba, uninstalled the program and re installed the webcam ....! updated bios notebook ....! useless!
the strange thing .. well that going into device manager ... the webcam is not there ....! but if the launch seems to open just then check quell caz ... Warning!!
Gan you help me?
Graziee

Are you familiar and comfortable with LINUX LIVE bootable discs to load an alternative operating system with unobtrusive but extensive Toshiba device support so you can determine if your webcam hardware is ruined or if the problem is software and possibly solved reinstalling Windows ?
At this point, you're pondering less time consuming but more expensive choices such as buying another web cam, or another computer and you might be temporarily borrowing someone else's web cam / using a non preferred spare web cam that isn't optimal for your needs.
Continuously downloading software, registry cleaners, and repeatedly reinstalling drivers will eventually ruin your Windows installation and consume more time than you've wasted so far and still doesn't guarantee to fix your malfunction.

TouchPad lock key does not work anymore on Dell XPS L401X

Hi everyone,
On my Dell XPS L401X laptop, there is a key to lock/unlock the touchpad. It used to work fine on Windows and on new fresh install ArchLinux, but now it does not work anymore. If I remember correctly, I did not change, configure any shortcut so far.
Any hint to fix this problem?
Many thanks!
Tinh

Try mapping the button as shown here: https://wiki.archlinux.org/index.php/To … are_Toggle
I'm sorry i can't help more.

TV does not work anymore on Qosmio G10

Good morning,
TV does not work anymore, may be due to an update. It has been working OK before.
When selecting TV option 'TV direct ' with MCE menu, I get the following error message: "necessary files for video display are not installed or do not work properly, restart MCE or the computer". Restarting MCE and / or G10 does not solve the problem.
-Intervideo WinDVD creator is installed.
-TV PCI tuner seems to work properly (as per hardware status)
Which files can be missing? What needs to be done?
Any help, suggestions, well appreciated.
Thank you to anyone answering this message.

Hello Luciano
Like you know on this way it is not easy to give you precise answer because we dont know what did you done exactly with your Qosmio.
Please try to use System restore tool at first and roll back the operating system to earlier time. Maybe this will help you and the MCE configuration will be as before.
Try it at first.

HT204135 I update my Mac to version 10.9.2 and now my printer does not work anymore. I did all the software updates and I do not understand why my mac does not recognize the printer anymore?

I update my Mac to version 10.9.2 and now my printer does not work anymore. I did all the software updates and I do not understand why my mac does not recognize the printer anymore?

Go to the website of the manufacturer of your printer and check to see if they have released an updated driver for your particular model.

While updating my ipad to new software through itunes it got stuck and does not work anymore - it just displays the screen with symbols of itunes and the cable to connect to it - help - what should i do?

while updating my ipad to new software through itunes it got stuck and does not work anymore - it just displays the screen with symbols of itunes and the cable to connect to it - help - what should i do?

Disconnect the iPad, do a Reset [Hold the Home and Sleep/Wake buttons down together for 10 seconds or so (until the Apple logo appears) and then release. The screen will go blank and then power ON again in the normal way.] It is 'appsolutely' safe!, reconnect and follow the prompts.
If that does not work then see here http://support.apple.com/kb/HT1808

I have recently upgraded from my iphone 5 to a new phone. My iphone 5 's touch screen does not work anymore. I need to backup my phone, but I can't do it on itunes without my password. Everything besides screen is ok. Is there a way around it? :(

I have recently upgraded from my iphone 5 to a new phone. My iphone 5 's touch screen does not work anymore. I need to backup my phone, but I can't do it on itunes without my password. Everything besides the screen is completely fine-the screen will not recognize my finger anymore. I am not trying to fix the phone, but I need to have my contacts. The pictures have already synced, but I need my password to do a full backup. Unfortunately, I can't type in my password. Is there any way around it? If I take my phone to the apple store, will they be able to help me? I am not willing to replace the screen just to do this, however, so that is out of the question.

Someone else may have a workaround, but, as far as I know, if you cannot interact with the screen on the iPhone, there is no way to unlock it so you can get to your contacts.
Were you saving them to iCloud by chance? If so, you can restore them to your new phone.
~Lyssa

After update Mac OS 10.9.1 Trim Enabler does not work anymore!

After updating from Mac OS 10.9.0 to 10.9.1 the program Trim Enabler does not work anymore and my 4 SSDs from Samsung and Kingston are no longer supported.
What can I do?
Should I scrap my SSDs?
Why does Apple do such things?
Will Apple that I switch to Windows? There Trim works with all SSDs and BluRay will not boycott!

Apple does not support TRIM for SSDs that were not factory
installed and TRIM Enabler is a hack to get around this. Any
hack is always subject to being disabled, or worse, with any
system update whether it is OSX or Windows.

Mac os 10.4.10 software update problem -- my mac does not work anymore :(

hello!
i have a powerbook G4- PPC. just today, i did a software update of my OS to 10.4.10 (it was the available update version according to the automatic uptae) and during the final stage of the installation, it says "a problem was encountered...installation package is moved to trash"
when i browsed my mac, my apps does not work anymore!!! they just bounce from the dock when i clicked it but it won't open any window. i emptied the trash and restarted my mac but sadly, it just boot but won't continue to the log in part, only in the silver window with the apple logo and mac os x tiger... and the mouse just turns into the color wheel. i waited for 30 mins and nothing happened.
i don't have a startup disc because the mac is a gift and it was long time ago. is ther a software i can use to fix or revert the changes of the unsuccessful OS update? why is there always a problem when i do OS update? isn't apple software stable?
My mac problems' driving me crazy!!!

There are no guarantees, but following this procedure when installing updates and upgrades on your Mac will go a long way towards avoiding unpleasant after effects and ‘post-update stress disorder’.
It is also worth noting that it is an extreme rarity for updates to cause upsets to your system, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
So before you do anything else:
If you can, make a full backup first.
Turn off sleep mode for both screen and hard disk.
1. Repair Permissions (in Disk Utility)
2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
3. Download the correct version of the COMBO update from the Apple download site. If your car runs on gasoline you would not want to fill the tank with diesel, so don’t try to install the PPC updater on an Intel Mac!
If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
Using the Combo updater ensures that all system files changed since the original 10.4.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.4.9 to 10.4.10. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
Now proceed as follows:
4. Close all applications.
5. Unplug all peripherals except your keyboard and mouse.
6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
8. Once your Mac is awake, repair permissions again, and you should be good to go!
If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious!
9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them 10.4.10. compliant. Give them a weeks or two while you regularly check their websites for updates. This applies particularly to plug-ins for Safari 3.
N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.
Lastly, Apple's own article on the subject of Software Update may also be useful reading:
http://docs.info.apple.com/article.html?artnum=106695

I am using Windows 7 64-bit. After installing Photoshop Elements 13 and trying to run it I always get the message: Photoshop does not work anymore. And it doesn't.

I am using Windows 7 64-bit. After installing Photoshop Elements 13 and trying to run it I always get the message: Photoshop does not work anymore. And it doesn't.

Hi Hardy Tasso,
Are you seeing this problem since first launch of PSE13 after installation or recently?
Please try:
Keep Ctrl + Alt + Shift keys pressed while launching PSE13 Editor and click OK on the dialog that comes next.
Thanks,
Anwesha

My Google search autocomplete me in Firefox does not work anymore. However, it still works with Internet Explorer. How can I fix this so Google gives me search suggestions again?

My Google search autocomplete me in Firefox does not work anymore. However, it still works with Internet Explorer. How can I fix this so Google gives me search suggestions again?

Solution update: Disabled XULRunner 1.9.1 extension from Add-ons > Extensions. Problem solved.

My new ipod classic does not work anymore! The music stopped and the display is dead. What now, besides calling support?

My new ipod classic does not work anymore! The music stopped and the display is dead. What now, besides calling support? Useless to say my PC didn't recognize the Ipod anymore either.

Anton, I wish I could help. I had an old iPod Classic (60 KB) as a gift but it went dead, I dropped it a few times accidentally, and it sat carefully saved until I had sufficient resources, energy and time to get the matter addressed. In my case, I actually took the thing (after making sure it was charged) to an Apple store and one of the geniuses at the genius bar at the back of the store took it and did a few things (unseen and un-noted) with his fingers and handed it to me with a sly smile. Voila, the thing was functional. I got a re-functionalized iTunes account and store access when I bought my iMac. I did lose a few tunes along the way because it didn't recognize my new iMac as the source (my old dead PC laptop), but I have a more functional memory than the iPod and recovered them all in other ways. The whole thing is humming better than ever. At over 11 gb full, I have 4.2 days worth of portable listening. Be patient; it took me four years to get musical nirvana in a pocket, but you'll get there faster. Call support.

I have an iphone4, and suddenly one day my factime app does not work anymore!! How do I get it to work again, Please?

I am using an iphone4. Suddenly one day my factime app does not work anymore!! How do I get it to work again, Could someone please me?

Try a reset or restart of the device. If it still does not appear on any of the home screens and cannot be found in a spotlight search, restore the device.

Re: TouchPad on Satellite L30 does not work anymore

Similar Messages

Maybe you are looking for