RE1000 nightmare when trying to estabilish a connection to WRT54GL
Hello.
I have a big problem with a brand new RE1000 I received today.
I unpacked it, plugged into power socket and began manual configuration over the Ethernet cable. And then the nightmare began...
But, before I start describing the problem - first some facts.
I have a WRT54GL router and several computers and printers connected to it, mostly via WiFi.
All machines have static IPs. DHCP is disabled. WiFi G-Only network is protected with WPA2-Personal (AES) security and broadcasts on channel 5 (2.432GHz). Normally I have MAC filter enabled, but I disabled it temporarily for the installation of the range expander.
The network is 192.168.0.0/27 with router using 192.168.0.1. Half of IP addresses from the pool are free.
Now, with my laptop, I configured RE1000 to use the first free static IP, which is 192.168.0.16. Set a proper submask of 255.255.255.224, gateway - to router's address (192.168.0.1), and addresses of both DNSs.
With all that set up, I've manually entered the wireless network information: my network SSID, WPA2-Personal AES and a passphrase.
But RE1000 won't connect to the network no matter what I do. It just says "Connecting" every time it auto-refreshes the page and after a while it simply says Down.
I've also tried to connect using the Site Survey, but with the same result.
In the logs I found this repeated message
[327] syslog: [INFO]WL_STA_AUTHO fail, f=4008
Wireless network signal is superman strong. RE1000 is located in the same room as router, about 3 meters from him.
There's absolutely no way I can make RE1000 to connect to my WRT54GL router (v.1.1 with Firmware Version: v4.30.16). I've lost several hours trying to make it work.
Has someone had any luck in estabilishing connection between those two CISCO products?
Or maybe my RE1000 unit is broken? I'm seriously considering sending it back.
Okay. I've tried everything. Reinstalling the firmware, resetting, moving RE1000 one meter closer to WRT54GL, disabling network security, enabling DHCP, changing router channels. Absolutely everything. And still this junk won't connect to the router. This is ridiculous.
[497] syslog: [INFO]WL_STA_AUTHO fail, f=4008
[498] syslog: [INFO]WL_STA_AUTHO fail, f=4008
[499] syslog: [INFO]WL_STA_AUTHO fail, f=4008
[500] syslog: [INFO]WL_STA_AUTHO fail, f=4008
[501] syslog: [INFO]WL_STA_AUTHO fail, f=4008
[502] syslog: [INFO]WL_STA_AUTHO fail, f=4008
[503] syslog: [INFO]WL_STA_AUTHO fail, f=4008
I'll try with Cisco support and see what they have to say about this issue.
Similar Messages
-
Problems when trying to get a connection
Hi, i'm doing some tests with Hibernate but i'm getting an error when Hibernate tries to get a connection from a pooled datasource.
Here is my session factory configuration:
<session-factory>
<property name="transaction.factory_class">org.hibernate.transaction.JTATransactionFactory</property>
<property name="connection.datasource">jdbc/CORE_DS</property>
<property name="dialect">org.hibernate.dialect.SQLServerDialect</property>
</session-factory>
I created a jdbc2.0 datasource called jdbc/CORE_DS
This is the error i'm getting:
java.lang.ExceptionInInitializerError
at com.sap.engine.services.ejb.exceptions.BaseRemoteException.writeReplace(BaseRemoteException.java:276)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:324)
at java.io.ObjectStreamClass.invokeWriteReplace(ObjectStreamClass.java:896)
at java.io.ObjectOutputStream.writeObject0(ObjectOutputStream.java:1011)
at java.io.ObjectOutputStream.writeObject(ObjectOutputStream.java:278)
at com.sap.engine.services.rmi_p4.DispatchImpl.throwException(DispatchImpl.java:135)
at com.sap.engine.services.rmi_p4.DispatchImpl._runInternal(DispatchImpl.java:296)
at com.sap.engine.services.rmi_p4.DispatchImpl._run(DispatchImpl.java:183)
at com.sap.engine.services.rmi_p4.server.P4SessionProcessor.request(P4SessionProcessor.java:119)
at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:37)
at com.sap.engine.core.cluster.impl6.session.UnorderedChannel$MessageRunner.run(UnorderedChannel.java:71)
at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
at java.security.AccessController.doPrivileged(Native Method)
at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:94)
at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:162)
Caused by: java.lang.ExceptionInInitializerError
at test.util.HibernateUtil.<clinit>(HibernateUtil.java:22)
at test.vo.EventManager.listEvents(EventManager.java:41)
at test.ejb.EventHandlerBean.getEvents(EventHandlerBean.java:54)
at test.ejb.EventHandlerObjectImpl0.getEvents(EventHandlerObjectImpl0.java:204)
at test.ejb.EventHandlerObjectImpl0p4_Skel.dispatch(EventHandlerObjectImpl0p4_Skel.java:119)
at com.sap.engine.services.rmi_p4.DispatchImpl._runInternal(DispatchImpl.java:294)
... 8 more
Caused by: java.lang.NullPointerException
at com.sap.engine.services.dbpool.spi.CPManagedConnectionFactoryImpl.createManagedConnection(CPManagedConnectionFactoryImpl.java:145)
at com.sap.engine.services.connector.jca.ConnectionHashSet.match(ConnectionHashSet.java:312)
at com.sap.engine.services.connector.jca.ConnectionManagerImpl.allocateConnection(ConnectionManagerImpl.java:231)
at com.sap.engine.services.dbpool.cci.ConnectionFactoryImpl.getConnection(ConnectionFactoryImpl.java:51)
at org.hibernate.connection.DatasourceConnectionProvider.getConnection(DatasourceConnectionProvider.java:59)
at org.hibernate.cfg.SettingsFactory.buildSettings(SettingsFactory.java:72)
at org.hibernate.cfg.Configuration.buildSettings(Configuration.java:1463)
at org.hibernate.cfg.Configuration.buildSessionFactory(Configuration.java:1004)
at test.util.HibernateUtil.<clinit>(HibernateUtil.java:18)
... 13 more
any ideas?
Thanks,
Juan Manuel
Message was edited by: Juan SanmarcoHi we are having a similar issue, could you please specify how you solved this?
Thanks
regards
Vincenzo -
ResourceException: Access not allowed (when trying to grab a connection from weblogic pool)
I am using WLS7 with SP1.
I just recently migrated from WLS6.0. When my code tries to grab a
connection from the pool, it throws an exception
java.sql.SQLException: Pool connect failed:
weblogic.common.ResourceException: Access not allowed
at weblogic.jdbc.pool.Driver.connect(Driver.java:202)
Does anyone know if anything changed from 6.0 to 7?
Here is a piece of the code that throws exception.
Driver driver =
(Driver)Class.forName("weblogic.jdbc.pool.Driver")
.newInstance();
conn = driver.connect("jdbc:weblogic:pool:" +
dbName, null);
Thanks in advance.Hi Jung,
"Jung Yang" <[email protected]> wrote in message
news:[email protected]...
Do you know how to change security setting on the connection pool?
Thanks.WebConsole:
1.Compatibility Security => ACLs
Create a new ACL,
name : weblogic.jdbc.connectionPool.yourPoolname
permission : reserve, reset
group : everynone
2.Services => JDBC => Connection Pool
Create a new Connection Pool
ACL Name : weblogic.jdbc.connectionPool.yourPoolname
In 'Target' tab, choose server and click the Apply button
Slava
>
"Slava Imeshev" <[email protected]> wrote in message
news:[email protected]...
Hi Jung,
Could you try providing weblogic user name and password
in the properties?
Could you also check security setting of the connection pool?
Regards,
Slava Imeshev
"Jung Yang" <[email protected]> wrote in message
news:[email protected]...
Well that is exactly what I am doing. The variable dbName is database
connection pool name that I created in weblogic console. Again, it
worked
in WLS6 but after migration, it stopped working.
Thanks.
"Mitesh Patel" <[email protected]> wrote in message
news:[email protected]...
In my code I am supplying name of the connection pool already
created
in
weblogic server. I am asking you to get connection from the pool
using
pool
driver.
In your case you are trying to create connection straight to
database
using pool
driver.
What I am asking is pass name of the connection pool instead of
database
name.
Thanks,
Mitesh
Jung Yang wrote:
What would be the difference between your code and mine? Mine
simple
appends dbName string value for connection pool name at the end of
"jdbc:weblogic:pool:"? And why same exact code would work in WLS6and
not
work in WLS7?
Thanks.
"Mitesh Patel" <[email protected]> wrote in message
news:[email protected]...
conn = driver.connect("jdbc:weblogic:pool:" +
dbName, null);Instead of doing this what if you use
Connection conn =
myDriver.connect("jdbc:weblogic:pool:myConnectionPool", null);
Will you please try this and see if that helps?
Mitesh
Jung Yang wrote:
Isn't that exactly what I posted for my code piece?
Thanks.
"Mitesh Patel" <[email protected]> wrote in message
news:[email protected]...
Try As described below:
The following example demonstrates how to use a database
connection
pool
from a servlet.
Load the pool driver and cast it to java.sql.Driver. The
full
pathname
of
the driver is weblogic.jdbc.pool.Driver. For example:
Driver myDriver = (Driver)
Class.forName("weblogic.jdbc.pool.Driver").newInstance();
Create a connection using the URL for the driver, plus
(optionally)
the
name of the registered connection pool. The URL of the pool
driver
is
jdbc:weblogic:pool.
You can identify the pool in either of two ways:
Specify the name of the connection pool in a
java.util.Properties
object
using the key connectionPoolID. For example:
Properties props = new
Properties();props.put("connectionPoolID",
"myConnectionPool");Connection conn =
myDriver.connect("jdbc:weblogic:pool", props);
Add the name of the pool to the end of the URL. In this case
you
do
not
need a Properties object unless you are setting a username
and
password
for using a connection from the pool. For example:
Connection conn =
myDriver.connect("jdbc:weblogic:pool:myConnectionPool",
null);
Note that the Driver.connect() method is used in theseexamples
instead of
the DriverManger.getConnection() method. Although you may
use
DriverManger.getConnection() to obtain a databaseconnection,
we
recommend
that you use Driver.connect() because this method is not
synchronized
and
provides better performance.
Note that the Connection returned by connect() is an
instance
of
weblogic.jdbc.pool.Connection.
Call the close() method on the Connection object when youfinish
with
your
JDBC calls, so that the connection is properly returned to
the
pool. A
good coding practice is to create the connection in a try
block
and
then
close the connection in a finally block, to make sure the
connection
is
closed in all cases.
conn.close();
Mitesh
Jung Yang wrote:
I am using WLS7 with SP1.
I just recently migrated from WLS6.0. When my code tries
to
grab a
connection from the pool, it throws an exception
java.sql.SQLException: Pool connect failed:
weblogic.common.ResourceException: Access not allowed
at
weblogic.jdbc.pool.Driver.connect(Driver.java:202)
Does anyone know if anything changed from 6.0 to 7?
Here is a piece of the code that throws exception.
Driver driver =
(Driver)Class.forName("weblogic.jdbc.pool.Driver")
.newInstance();
conn =
driver.connect("jdbc:weblogic:pool:"
+
dbName,
null);
>>>>>>>>>
Thanks in advance. -
WebDynpro Debugger stuck when trying to establish a connection
Hello!
I am trying to debug a webdynpro java application. My NWDS version is 7.0 SP13.
When i tried to debug, the debugger keep trying to establish a connection forever. Do you know what is the issue?
My server0 debug mode is on, standard debug port. I was able to do the debug before. Please let me know if you have any suggestion for my issue. Thank you very much.Try changing these values.
In Studio:
Window -> Preferences -> Java -> Debug
Debugger timeout (ms)
Launch timeout (ms)
To those two values, add an extra zero.
If it doesnt work, restart your server. Or your network is getting clogged up. -
Server deadlocked when trying to reserve a connection
I have domain which has a connection pool with four connections. Under certain circumstances all four connections are in use. A fifth thread comes along, tries to get a connection and causes a deadlock. Question is why doesn't the connection reserve timeout (10 seconds) kick in and break the deadlock ? Is this a bug in WLS ?
I am just curious here. I was able to solve this by increasing the number of connections and also changing a singleton number generator that was involved in the picture. But the root cause appears to be the behaviour of the DataSource.getConnection call. Any info will be appreciated.
"ExecuteThread: '17' for queue: 'weblogic.kernel.Default'" daemon prio=5 tid=0x1
f354ca8 nid=0x1d in Object.wait() [20609000..2060b1a8]
at java.lang.Object.wait(Native Method)
- waiting on <ff8e718> (a weblogic.jdbc.common.internal.ConnectionPool)
at weblogic.common.resourcepool.ResourcePoolImpl.reserveResource(Resourc
ePoolImpl.java:414)
- locked <ff8e718> (a weblogic.jdbc.common.internal.ConnectionPool)
at weblogic.jdbc.common.internal.ConnectionPool.reserve(ConnectionPool.j
ava:430)
at weblogic.jdbc.common.internal.ConnectionPoolManager.reserve(Connectio
nPoolManager.java:78)
at weblogic.jdbc.jta.DataSource.getXAConnectionFromPool(DataSource.java:
1329)
at weblogic.jdbc.jta.DataSource.refreshXAConnAndEnlist(DataSource.java:1
198)
at weblogic.jdbc.jta.DataSource.getConnection(DataSource.java:385)
at weblogic.jdbc.jta.DataSource.connect(DataSource.java:343)
at weblogic.jdbc.common.internal.RmiDataSource.getConnection(RmiDataSour
ce.java:305)
at com.zowi.common.db.DatabaseContext.getConnection(DatabaseContext.java
:367)
at com.zowi.common.db.DatabaseContext.getPreparedStatement(DatabaseConte
xt.java:472)
at com.zowi.common.db.DatabaseContext.getPreparedStatement(DatabaseConte
xt.java:455)
at com.zowi.managers.ejb.sequence.SequenceManagerBean.getCurrentSequence
(SequenceManagerBean.java:170)
at com.zowi.managers.ejb.sequence.SequenceManager_k49jdc_ELOImpl.getCurr
entSequence(SequenceManager_k49jdc_ELOImpl.java:103)
at com.zowi.common.db.SequenceNbrGenerator.getNewNumber(SequenceNbrGener
ator.java:90)
- locked <11943dd0> (a com.zowi.common.db.SequenceNbrGenerator)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:90)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:67)
at com.zowi.common.util.SqlUtil.getLongSequence(SqlUtil.java:41)
at com.zowi.managers.dao.CardManager.insertCard(CardManager.java:2266)We are using WLS81SP2 (on HP NonStop Server). Here is the full thread dump. Subsequent dumps show no runnable activity other than muxer polling.
Full thread dump Java HotSpot(TM) Server VM (1.4.1 mixed mode):
"ListenThread.Default" prio=5 tid=0x1ef1bd00 nid=0x3d runnable [2142e000..2142e9a8]
at java.net.PlainSocketImpl.socketAccept(Native Method)
at java.net.PlainSocketImpl.accept(PlainSocketImpl.java:353)
- locked <1170b670> (a java.net.PlainSocketImpl)
at java.net.ServerSocket.implAccept(ServerSocket.java:448)
at java.net.ServerSocket.accept(ServerSocket.java:419)
at weblogic.socket.WeblogicServerSocket.accept(WeblogicServerSocket.java:24)
at weblogic.t3.srvr.ListenThread.accept(ListenThread.java:739)
at weblogic.t3.srvr.ListenThread.run(ListenThread.java:292)
"Thread-9" prio=5 tid=0x1e3c73e8 nid=0x3c runnable [213ac000..213ac9a8]
at java.net.PlainDatagramSocketImpl.receive(Native Method)
- locked <1170b960> (a java.net.PlainDatagramSocketImpl)
at java.net.DatagramSocket.receive(DatagramSocket.java:680)
- locked <1170b990> (a java.net.DatagramPacket)
- locked <1170b9b0> (a java.net.DatagramSocket)
at snmp.SNMPv1AgentInterface.run(SNMPv1AgentInterface.java:183)
at java.lang.Thread.run(Thread.java:536)
"Thread-6" daemon prio=5 tid=0x1f4163f0 nid=0x3a in Object.wait() [2132a000..2132a9a8]
at java.lang.Object.wait(Native Method)
- waiting on <1170ba30> (a com.zowi.common.util.Queue)
at com.zowi.common.log.Log.run(Log.java:126)
- locked <1170ba30> (a com.zowi.common.util.Queue)
at java.lang.Thread.run(Thread.java:536)
"zowi.watchdog" daemon prio=5 tid=0x1f3d8fa0 nid=0x39 in Object.wait() [212a8000..212a89a8]
at java.lang.Object.wait(Native Method)
- waiting on <1170ba58> (a com.zowi.common.helper.Watchdog)
at com.zowi.common.helper.Watchdog.run(Watchdog.java:54)
- locked <1170ba58> (a com.zowi.common.helper.Watchdog)
"Thread-5" prio=5 tid=0x1ec172a8 nid=0x37 in Object.wait() [1fb18000..1fb189a8]
at java.lang.Object.wait(Native Method)
- waiting on <ff66ea0> (a java.util.TaskQueue)
at java.util.TimerThread.mainLoop(Timer.java:429)
- locked <ff66ea0> (a java.util.TaskQueue)
at java.util.TimerThread.run(Timer.java:382)
"weblogic.health.CoreHealthMonitor" daemon prio=5 tid=0x1ebeb000 nid=0x36 waiting on condition [1f7cc000..1f7cd1a8]
at java.lang.Thread.sleep(Native Method)
at weblogic.t3.srvr.CoreHealthMonitorThread.run(CoreHealthMonitorThread.java:127)
"Thread-4" prio=5 tid=0x822d4d8 nid=0x35 in Object.wait() [1f74a000..1f74b1a8]
at java.lang.Object.wait(Native Method)
- waiting on <fa36fc0> (a java.util.TaskQueue)
at java.util.TimerThread.mainLoop(Timer.java:429)
- locked <fa36fc0> (a java.util.TaskQueue)
at java.util.TimerThread.run(Timer.java:382)
"LDAPConnThread-0 ldap://16.74.49.24:7001" daemon prio=5 tid=0x1f649588 nid=0x34 runnable [21136000..211371a8]
at java.net.SocketInputStream.socketRead0(Native Method)
at java.net.SocketInputStream.read(SocketInputStream.java:129)
at java.io.BufferedInputStream.fill(BufferedInputStream.java:183)
at java.io.BufferedInputStream.read(BufferedInputStream.java:201)
- locked <fa37890> (a java.io.BufferedInputStream)
at netscape.ldap.ber.stream.BERElement.getElement(BERElement.java:101)
at netscape.ldap.LDAPConnThread.run(LDAPConnThread.java:538)
at java.lang.Thread.run(Thread.java:536)
"VDE Transaction Processor Thread" prio=2 tid=0x1f63bd10 nid=0x32 in Object.wait() [210b4000..210b51a8]
at java.lang.Object.wait(Native Method)
- waiting on <fa37928> (a com.octetstring.vde.backend.standard.TransactionProcessor)
at java.lang.Object.wait(Object.java:426)
at com.octetstring.vde.backend.standard.TransactionProcessor.waitChange(TransactionProcessor.java:356)
- locked <fa37928> (a com.octetstring.vde.backend.standard.TransactionProcessor)
at com.octetstring.vde.backend.standard.TransactionProcessor.run(TransactionProcessor.java:212)
"ExecuteThread: '2' for queue: 'weblogic.admin.RMI'" daemon prio=5 tid=0x1f51f340 nid=0x31 in Object.wait() [21032000..210331a8]
at java.lang.Object.wait(Native Method)
- waiting on <fa379a0> (a weblogic.kernel.ExecuteThread)
at java.lang.Object.wait(Object.java:426)
at weblogic.kernel.ExecuteThread.waitForRequest(ExecuteThread.java:145)
- locked <fa379a0> (a weblogic.kernel.ExecuteThread)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:164)
"ExecuteThread: '1' for queue: 'weblogic.admin.RMI'" daemon prio=5 tid=0x1f51f050 nid=0x30 in Object.wait() [20fb0000..20fb11a8]
at java.lang.Object.wait(Native Method)
- waiting on <fa37a18> (a weblogic.kernel.ExecuteThread)
at java.lang.Object.wait(Object.java:426)
at weblogic.kernel.ExecuteThread.waitForRequest(ExecuteThread.java:145)
- locked <fa37a18> (a weblogic.kernel.ExecuteThread)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:164)
"ExecuteThread: '0' for queue: 'weblogic.admin.RMI'" daemon prio=5 tid=0x1f51eda0 nid=0x2f in Object.wait() [20f2e000..20f2f1a8]
at java.lang.Object.wait(Native Method)
- waiting on <fa37a90> (a weblogic.kernel.ExecuteThread)
at java.lang.Object.wait(Object.java:426)
at weblogic.kernel.ExecuteThread.waitForRequest(ExecuteThread.java:145)
- locked <fa37a90> (a weblogic.kernel.ExecuteThread)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:164)
"ExecuteThread: '2' for queue: 'weblogic.socket.Muxer'" daemon prio=5 tid=0x1f074d20 nid=0x2e waiting for monitor entry [20eac000..20ead1a8]
at weblogic.socket.PosixSocketMuxer.processSockets(PosixSocketMuxer.java:93)
- waiting to lock <fa37b80> (a java.lang.String)
at weblogic.socket.SocketReaderRequest.execute(SocketReaderRequest.java:32)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
"ExecuteThread: '1' for queue: 'weblogic.socket.Muxer'" daemon prio=5 tid=0x1f074bb8 nid=0x2d waiting for monitor entry [20e2a000..20e2b1a8]
at weblogic.socket.PosixSocketMuxer.processSockets(PosixSocketMuxer.java:93)
- waiting to lock <fa37b80> (a java.lang.String)
at weblogic.socket.SocketReaderRequest.execute(SocketReaderRequest.java:32)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
"ExecuteThread: '0' for queue: 'weblogic.socket.Muxer'" daemon prio=5 tid=0x1ec7d448 nid=0x2c runnable [20da8000..20da91a8]
at weblogic.socket.PosixSocketMuxer.poll(Native Method)
at weblogic.socket.PosixSocketMuxer.processSockets(PosixSocketMuxer.java:100)
- locked <fa37b80> (a java.lang.String)
at weblogic.socket.SocketReaderRequest.execute(SocketReaderRequest.java:32)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
"weblogic.security.SpinnerRandomSource" daemon prio=5 tid=0x1f38a868 nid=0x2b in Object.wait() [20d26000..20d271a8]
at java.lang.Object.wait(Native Method)
- waiting on <fa5bd68> (a java.lang.Object)
at java.lang.Object.wait(Object.java:426)
at weblogic.security.SpinnerRandomBitsSource.run(SpinnerRandomBitsSource.java:60)
- locked <fa5bd68> (a java.lang.Object)
at java.lang.Thread.run(Thread.java:536)
"weblogic.time.TimeEventGenerator" daemon prio=9 tid=0x1f35edb8 nid=0x2a in Object.wait() [20ca4000..20ca51a8]
at java.lang.Object.wait(Native Method)
- waiting on <fa5bdd8> (a weblogic.time.common.internal.TimeTable)
at weblogic.time.common.internal.TimeTable.snooze(TimeTable.java:271)
- locked <fa5bdd8> (a weblogic.time.common.internal.TimeTable)
at weblogic.time.common.internal.TimeEventGenerator.run(TimeEventGenerator.java:118)
at java.lang.Thread.run(Thread.java:536)
"ExecuteThread: '4' for queue: 'weblogic.kernel.System'" daemon prio=5 tid=0x1f35dfa8 nid=0x29 in Object.wait() [20c22000..20c231a8]
at java.lang.Object.wait(Native Method)
- waiting on <fa5be48> (a weblogic.kernel.ExecuteThread)
at java.lang.Object.wait(Object.java:426)
at weblogic.kernel.ExecuteThread.waitForRequest(ExecuteThread.java:145)
- locked <fa5be48> (a weblogic.kernel.ExecuteThread)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:164)
"ExecuteThread: '3' for queue: 'weblogic.kernel.System'" daemon prio=5 tid=0x1f35d368 nid=0x28 in Object.wait() [20ba0000..20ba11a8]
at java.lang.Object.wait(Native Method)
- waiting on <fa5bec0> (a weblogic.kernel.ExecuteThread)
at java.lang.Object.wait(Object.java:426)
at weblogic.kernel.ExecuteThread.waitForRequest(ExecuteThread.java:145)
- locked <fa5bec0> (a weblogic.kernel.ExecuteThread)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:164)
"ExecuteThread: '2' for queue: 'weblogic.kernel.System'" daemon prio=5 tid=0x1f35c728 nid=0x27 in Object.wait() [20b1e000..20b1f1a8]
at java.lang.Object.wait(Native Method)
- waiting on <fa5bf38> (a weblogic.kernel.ExecuteThread)
at java.lang.Object.wait(Object.java:426)
at weblogic.kernel.ExecuteThread.waitForRequest(ExecuteThread.java:145)
- locked <fa5bf38> (a weblogic.kernel.ExecuteThread)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:164)
"ExecuteThread: '1' for queue: 'weblogic.kernel.System'" daemon prio=5 tid=0x1f35bae8 nid=0x26 in Object.wait() [20a9c000..20a9d1a8]
at java.lang.Object.wait(Native Method)
- waiting on <fa5bfb0> (a weblogic.kernel.ExecuteThread)
at java.lang.Object.wait(Object.java:426)
at weblogic.kernel.ExecuteThread.waitForRequest(ExecuteThread.java:145)
- locked <fa5bfb0> (a weblogic.kernel.ExecuteThread)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:164)
"ExecuteThread: '0' for queue: 'weblogic.kernel.System'" daemon prio=5 tid=0x1f35aea8 nid=0x25 in Object.wait() [20a1a000..20a1b1a8]
at java.lang.Object.wait(Native Method)
- waiting on <fa5c028> (a weblogic.kernel.ExecuteThread)
at java.lang.Object.wait(Object.java:426)
at weblogic.kernel.ExecuteThread.waitForRequest(ExecuteThread.java:145)
- locked <fa5c028> (a weblogic.kernel.ExecuteThread)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:164)
"ExecuteThread: '24' for queue: 'weblogic.kernel.Default'" daemon prio=5 tid=0x1f35a268 nid=0x24 waiting for monitor entry [20998000..209991a8]
at com.zowi.common.db.SequenceNbrGenerator.getNewNumber(SequenceNbrGenerator.java:81)
- waiting to lock <11943dd0> (a com.zowi.common.db.SequenceNbrGenerator)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:90)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:67)
at com.zowi.common.util.SqlUtil.getLongSequence(SqlUtil.java:41)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:150)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:105)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandler_ybado0_EOImpl.process(IssuerViewHandler_ybado0_EOImpl.java:102)
at com.zowi.servlets.appserver.EjbServlet.doPost(EjbServlet.java:129)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run(ServletStubImpl.java:971)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:402)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:305)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:6350)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:317)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:118)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3635)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
"ExecuteThread: '23' for queue: 'weblogic.kernel.Default'" daemon prio=5 tid=0x1f359628 nid=0x23 waiting for monitor entry [20915000..209171a8]
at com.zowi.common.db.SequenceNbrGenerator.getNewNumber(SequenceNbrGenerator.java:81)
- waiting to lock <11943dd0> (a com.zowi.common.db.SequenceNbrGenerator)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:90)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:67)
at com.zowi.common.util.SqlUtil.getLongSequence(SqlUtil.java:41)
at com.zowi.managers.dao.CardManager.insertCard(CardManager.java:2266)
at com.zowi.managers.dao.CardManager.getorInsertCardInfo(CardManager.java:1312)
at com.zowi.services.issuer.ejb.card.IssuerCardServicesBean.initializeTransaction(IssuerCardServicesBean.java:809)
at com.zowi.services.issuer.ejb.card.IssuerCardServices_lier6m_ELOImpl.initializeTransaction(IssuerCardServices_lier6m_ELOImpl.java:46)
at com.zowi.services.issuer.ejb.BaseIssuerBean.init(BaseIssuerBean.java:167)
at com.zowi.services.issuer.ejb.BaseIssuerBean.execute(BaseIssuerBean.java:117)
at com.zowi.services.issuer.ejb.olmauthorization.IssuerOlmAuthorizationServicesBean_ryrje8_ELOImpl.execute(IssuerOlmAuthorizationServicesBean_ryrje8_ELOImpl.java:160)
at com.zowi.common.util.EjbUtil.invokeServiceBean(EjbUtil.java:167)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:192)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:105)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandler_ybado0_EOImpl.process(IssuerViewHandler_ybado0_EOImpl.java:102)
at com.zowi.servlets.appserver.EjbServlet.doPost(EjbServlet.java:129)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run(ServletStubImpl.java:971)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:402)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:305)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:6350)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:317)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:118)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3635)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
"ExecuteThread: '22' for queue: 'weblogic.kernel.Default'" daemon prio=5 tid=0x1f3589e8 nid=0x22 waiting for monitor entry [20894000..208951a8]
at com.zowi.common.db.SequenceNbrGenerator.getNewNumber(SequenceNbrGenerator.java:81)
- waiting to lock <11943dd0> (a com.zowi.common.db.SequenceNbrGenerator)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:90)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:67)
at com.zowi.common.util.SqlUtil.getLongSequence(SqlUtil.java:41)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:150)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:105)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandler_ybado0_EOImpl.process(IssuerViewHandler_ybado0_EOImpl.java:102)
at com.zowi.servlets.appserver.EjbServlet.doPost(EjbServlet.java:129)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run(ServletStubImpl.java:971)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:402)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:305)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:6350)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:317)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:118)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3635)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
"ExecuteThread: '21' for queue: 'weblogic.kernel.Default'" daemon prio=5 tid=0x1f357da8 nid=0x21 waiting for monitor entry [20811000..208131a8]
at com.zowi.common.db.SequenceNbrGenerator.getNewNumber(SequenceNbrGenerator.java:81)
- waiting to lock <11943dd0> (a com.zowi.common.db.SequenceNbrGenerator)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:90)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:67)
at com.zowi.common.util.SqlUtil.getLongSequence(SqlUtil.java:41)
at com.zowi.managers.dao.CardManager.insertCard(CardManager.java:2266)
at com.zowi.managers.dao.CardManager.getorInsertCardInfo(CardManager.java:1312)
at com.zowi.services.issuer.ejb.card.IssuerCardServicesBean.initializeTransaction(IssuerCardServicesBean.java:809)
at com.zowi.services.issuer.ejb.card.IssuerCardServices_lier6m_ELOImpl.initializeTransaction(IssuerCardServices_lier6m_ELOImpl.java:46)
at com.zowi.services.issuer.ejb.BaseIssuerBean.init(BaseIssuerBean.java:167)
at com.zowi.services.issuer.ejb.BaseIssuerBean.execute(BaseIssuerBean.java:117)
at com.zowi.services.issuer.ejb.olmauthorization.IssuerOlmAuthorizationServicesBean_ryrje8_ELOImpl.execute(IssuerOlmAuthorizationServicesBean_ryrje8_ELOImpl.java:160)
at com.zowi.common.util.EjbUtil.invokeServiceBean(EjbUtil.java:167)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:192)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:105)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandler_ybado0_EOImpl.process(IssuerViewHandler_ybado0_EOImpl.java:102)
at com.zowi.servlets.appserver.EjbServlet.doPost(EjbServlet.java:129)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run(ServletStubImpl.java:971)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:402)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:305)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:6350)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:317)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:118)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3635)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
"ExecuteThread: '20' for queue: 'weblogic.kernel.Default'" daemon prio=5 tid=0x1f357168 nid=0x20 waiting for monitor entry [20790000..207911a8]
at com.zowi.common.db.SequenceNbrGenerator.getNewNumber(SequenceNbrGenerator.java:81)
- waiting to lock <11943dd0> (a com.zowi.common.db.SequenceNbrGenerator)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:90)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:67)
at com.zowi.common.util.SqlUtil.getLongSequence(SqlUtil.java:41)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:150)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:105)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandler_ybado0_EOImpl.process(IssuerViewHandler_ybado0_EOImpl.java:102)
at com.zowi.servlets.appserver.EjbServlet.doPost(EjbServlet.java:129)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run(ServletStubImpl.java:971)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:402)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:305)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:6350)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:317)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:118)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3635)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
"ExecuteThread: '19' for queue: 'weblogic.kernel.Default'" daemon prio=5 tid=0x1f356528 nid=0x1f waiting for monitor entry [2070e000..2070f1a8]
at com.zowi.common.db.SequenceNbrGenerator.getNewNumber(SequenceNbrGenerator.java:81)
- waiting to lock <11943dd0> (a com.zowi.common.db.SequenceNbrGenerator)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:90)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:67)
at com.zowi.common.util.SqlUtil.getLongSequence(SqlUtil.java:41)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:150)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:105)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandler_ybado0_EOImpl.process(IssuerViewHandler_ybado0_EOImpl.java:102)
at com.zowi.servlets.appserver.EjbServlet.doPost(EjbServlet.java:129)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run(ServletStubImpl.java:971)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:402)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:305)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:6350)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:317)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:118)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3635)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
"ExecuteThread: '18' for queue: 'weblogic.kernel.Default'" daemon prio=5 tid=0x1f3558e8 nid=0x1e waiting for monitor entry [2068c000..2068d1a8]
at com.zowi.common.db.SequenceNbrGenerator.getNewNumber(SequenceNbrGenerator.java:81)
- waiting to lock <11943dd0> (a com.zowi.common.db.SequenceNbrGenerator)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:90)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:67)
at com.zowi.common.util.SqlUtil.getLongSequence(SqlUtil.java:41)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:150)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:105)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandler_ybado0_EOImpl.process(IssuerViewHandler_ybado0_EOImpl.java:102)
at com.zowi.servlets.appserver.EjbServlet.doPost(EjbServlet.java:129)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run(ServletStubImpl.java:971)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:402)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:305)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:6350)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:317)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:118)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3635)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
"ExecuteThread: '17' for queue: 'weblogic.kernel.Default'" daemon prio=5 tid=0x1f354ca8 nid=0x1d in Object.wait() [20609000..2060b1a8]
at java.lang.Object.wait(Native Method)
- waiting on <ff8e718> (a weblogic.jdbc.common.internal.ConnectionPool)
at weblogic.common.resourcepool.ResourcePoolImpl.reserveResource(ResourcePoolImpl.java:414)
- locked <ff8e718> (a weblogic.jdbc.common.internal.ConnectionPool)
at weblogic.jdbc.common.internal.ConnectionPool.reserve(ConnectionPool.java:430)
at weblogic.jdbc.common.internal.ConnectionPoolManager.reserve(ConnectionPoolManager.java:78)
at weblogic.jdbc.jta.DataSource.getXAConnectionFromPool(DataSource.java:1329)
at weblogic.jdbc.jta.DataSource.refreshXAConnAndEnlist(DataSource.java:1198)
at weblogic.jdbc.jta.DataSource.getConnection(DataSource.java:385)
at weblogic.jdbc.jta.DataSource.connect(DataSource.java:343)
at weblogic.jdbc.common.internal.RmiDataSource.getConnection(RmiDataSource.java:305)
at com.zowi.common.db.DatabaseContext.getConnection(DatabaseContext.java:367)
at com.zowi.common.db.DatabaseContext.getPreparedStatement(DatabaseContext.java:472)
at com.zowi.common.db.DatabaseContext.getPreparedStatement(DatabaseContext.java:455)
at com.zowi.managers.ejb.sequence.SequenceManagerBean.getCurrentSequence(SequenceManagerBean.java:170)
at com.zowi.managers.ejb.sequence.SequenceManager_k49jdc_ELOImpl.getCurrentSequence(SequenceManager_k49jdc_ELOImpl.java:103)
at com.zowi.common.db.SequenceNbrGenerator.getNewNumber(SequenceNbrGenerator.java:90)
- locked <11943dd0> (a com.zowi.common.db.SequenceNbrGenerator)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:90)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:67)
at com.zowi.common.util.SqlUtil.getLongSequence(SqlUtil.java:41)
at com.zowi.managers.dao.CardManager.insertCard(CardManager.java:2266)
at com.zowi.managers.dao.CardManager.getorInsertCardInfo(CardManager.java:1312)
at com.zowi.services.issuer.ejb.card.IssuerCardServicesBean.initializeTransaction(IssuerCardServicesBean.java:809)
at com.zowi.services.issuer.ejb.card.IssuerCardServices_lier6m_ELOImpl.initializeTransaction(IssuerCardServices_lier6m_ELOImpl.java:46)
at com.zowi.services.issuer.ejb.BaseIssuerBean.init(BaseIssuerBean.java:167)
at com.zowi.services.issuer.ejb.BaseIssuerBean.execute(BaseIssuerBean.java:117)
at com.zowi.services.issuer.ejb.olmauthorization.IssuerOlmAuthorizationServicesBean_ryrje8_ELOImpl.execute(IssuerOlmAuthorizationServicesBean_ryrje8_ELOImpl.java:160)
at com.zowi.common.util.EjbUtil.invokeServiceBean(EjbUtil.java:167)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:192)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:105)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandler_ybado0_EOImpl.process(IssuerViewHandler_ybado0_EOImpl.java:102)
at com.zowi.servlets.appserver.EjbServlet.doPost(EjbServlet.java:129)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run(ServletStubImpl.java:971)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:402)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:305)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:6350)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:317)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:118)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3635)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2585)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
"ExecuteThread: '16' for queue: 'weblogic.kernel.Default'" daemon prio=5 tid=0x1f354068 nid=0x1c waiting for monitor entry [20588000..205891a8]
at com.zowi.common.db.SequenceNbrGenerator.getNewNumber(SequenceNbrGenerator.java:81)
- waiting to lock <11943dd0> (a com.zowi.common.db.SequenceNbrGenerator)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:90)
at com.zowi.common.util.SqlUtil.getRawSequence(SqlUtil.java:67)
at com.zowi.common.util.SqlUtil.getLongSequence(SqlUtil.java:41)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:150)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandlerBean.process(IssuerViewHandlerBean.java:105)
at com.zowi.services.issuer.ejb.viewhandler.IssuerViewHandler_ybado0_EOImpl.process(IssuerViewHandler_ybado0_EOImpl.java:102)
at com.zowi.servlets.appserver.EjbServlet.doPost(EjbServlet.java:129)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at weblogic.servlet.internal.Servle -
Error "4" when trying to test my connection
Hi, please help me find out how to fix this error:
when i try to test the connection pops up an error message with only a number "4" in it, nothing else. what's this error message about and how do i fix it??
Thanx in advance!!!Hi,
unfortunately we cannot help without having connection to that database. It looks like you are trying to connect to Oracle 8 - not supported anymore.
Philip -
I'm trying to install and configure NSX 6.1.2 / ESX 5.5 in a nested environment using VMware Workstation lastest bits "VMware-workstation-full-11.1.0-2496824"
I've configured the MTU on the virtual adapter (VMNet1) used by the VXLAN transport network to 9000 bytes.
C:\Users\admin>netsh int ipv4 show int
Idx Met MTU State Name
1 50 4294967295 connected Loopback Pseudo-Interface 1
19 25 1500 connected Wireless Network Connection 4
16 40 1500 disconnected Bluetooth Network Connection
11 5 1500 disconnected Local Area Connection
20 5 1500 disconnected Wireless Network Connection 5
18 5 1400 disconnected Local Area Connection* 11
31 20 9000 connected VMware Network Adapter VMnet1
when I test VTEP connectivity between ESXi nested host with MTU > 1500, using the following command,
ping ++netstack=vxlan -d -s 1572 -I vmk2 192.168.192.102
the ESXi crashes with the following error
2015-05-21T11:20:47.180+02:00| vcpu-1| I120: Coredump encountered overflow 10218:10218 (2172 duplicates)
2015-05-21T11:20:48.969+02:00| vcpu-1| I120: Backtrace:
2015-05-21T11:20:48.970+02:00| vcpu-1| I120: backtrace[00] frame 0x0881eb38 IP 0x13f0820de params 0 0xa6 0x64e 0x312d75706376 ??? [C:\Program Files (x86)\VMware\VMware Workstation\x64\vmware-vmx.exe base 0x13f050000 0x0001:0x000310de]
2015-05-21T11:20:48.971+02:00| vcpu-1| I120: backtrace[01] frame 0x0881f460 IP 0x13f068129 params 0x13f78dc30 0x13f890928 0x2ce 0x3fff ??? [C:\Program Files (x86)\VMware\VMware Workstation\x64\vmware-vmx.exe base 0x13f050000 0x0001:0x00017129]
2015-05-21T11:20:48.971+02:00| vcpu-1| I120: backtrace[02] frame 0x0881f8b0 IP 0x13f4498bc params 0x13fb8e840 0x3a63ec0 0x13f050000 0x13fb8e840 opus_decoder_destroy + 0x1dec0c [C:\Program Files (x86)\VMware\VMware Workstation\x64\vmware-vmx.exe base 0x13f050000 0x0001:0x003f88bc]
2015-05-21T11:20:48.972+02:00| vcpu-1| I120: backtrace[03] frame 0x0881f8e0 IP 0x13f6809a2 params 0x161 0x35a59e0 0 0xa36333237 opus_repacketizer_get_nb_frames + 0x163fc2 [C:\Program Files (x86)\VMware\VMware Workstation\x64\vmware-vmx.exe base 0x13f050000 0x0001:0x0062f9a2]
2015-05-21T11:20:48.972+02:00| vcpu-1| I120: backtrace[04] frame 0x0881f920 IP 0x13f6b8229 params 0x258 0 0 0 opus_repacketizer_get_nb_frames + 0x19b849 [C:\Program Files (x86)\VMware\VMware Workstation\x64\vmware-vmx.exe base 0x13f050000 0x0001:0x00667229]
2015-05-21T11:20:48.973+02:00| vcpu-1| I120: backtrace[05] frame 0x0881faa0 IP 0x13f680d3c params 0x13f809d60 0x13f7c7374 0x5 0x13fd65da0 opus_repacketizer_get_nb_frames + 0x16435c [C:\Program Files (x86)\VMware\VMware Workstation\x64\vmware-vmx.exe base 0x13f050000 0x0001:0x0062fd3c]
2015-05-21T11:20:48.973+02:00| vcpu-1| I120: backtrace[06] frame 0x0881fb00 IP 0x13f20c736 params 0 0 0 0 ??? [C:\Program Files (x86)\VMware\VMware Workstation\x64\vmware-vmx.exe base 0x13f050000 0x0001:0x001bb736]
2015-05-21T11:20:48.976+02:00| vcpu-1| I120: backtrace[07] frame 0x0881fb08 IP 0x76ee59cd params 0 0 0 0 BaseThreadInitThunk + 0x000d [C:\Windows\system32\kernel32.dll base 0x76ed0000 0x0001:0x000149cd]
2015-05-21T11:20:48.980+02:00| vcpu-1| I120: backtrace[08] frame 0x0881fb38 IP 0x7701b891 params 0 0 0 0 RtlUserThreadStart + 0x0021 [C:\Windows\SYSTEM32\ntdll.dll base 0x76ff0000 0x0001:0x0002a891]
2015-05-21T11:20:48.980+02:00| vcpu-1| I120: Msg_Post: Error
2015-05-21T11:20:48.980+02:00| vcpu-1| I120: [msg.log.error.unrecoverable] VMware Workstation unrecoverable error: (vcpu-1)
2015-05-21T11:20:48.980+02:00| vcpu-1| I120+ VERIFY d:/build/ob/bora-2496824/bora/devices/vmxnet3/vmxnet3_hosted.c:718
2015-05-21T11:20:48.980+02:00| vcpu-1| I120: [msg.panic.haveLog] A log file is available in "X:\vCACupdate\Capricornus\vmware.log".
2015-05-21T11:20:48.980+02:00| vcpu-1| I120: [msg.panic.requestSupport.withoutLog] You can request support.
2015-05-21T11:20:48.980+02:00| vcpu-1| I120: [msg.panic.requestSupport.vmSupport.windowsOrLinux]
2015-05-21T11:20:48.980+02:00| vcpu-1| I120+ To collect data to submit to VMware support, choose "Collect Support Data" from the Help menu.
2015-05-21T11:20:48.980+02:00| vcpu-1| I120+ You can also run the "vm-support" script in the Workstation folder directly.
2015-05-21T11:20:48.980+02:00| vcpu-1| I120: [msg.panic.response] We will respond on the basis of your support entitlement.
Any help is appreciated.One detail:
I use Vcloud from my work, so I changed iPv4 addresses of machines. For example, DC1 192.168.2.101,
Internet names are 192.169.2.101 and so on.
I mean it is fine that IP addresses differ from mentioned in guide -
Not-identified error when trying to make a connection in CS4
Hello;
When I try to make a Db connection to mysql in DW CS4,using connections,the +-button and fill in the pop up,I am getting the following message:
"a not-identified error has occurred".
The database name,password and all the other information is ok.So I really do not know what is happening.
Is there someone there who has an answer for this problem??
many thanks for the help!Igorbuitendijk wrote:
The testing serverfolder is:http://www.checksite.eu:2222/public_htmlThe URL prefix is:http://www.checksite.eu:2222/public_html
When I leave out the 2222,Dreamweaver can't make a connection to the server.
I don't know about the use of port 2222, but your testing server definition is completely wrong.
The testing server folder must be a physical path, not a URL. And the URL prefix must be a valid URL. public_html is the name of the web server's document root, it should never be part of a URL.
Judging from the details you have given here, you are using your remote server for testing. In the Testing server section of the site definition, set Access to FTP. The value of Host directory should be what your hosting company tells you to use when logging in. For some hosting companies, you use public_html on its own. Other companies tell you to leave the value blank or to use just /.
The URL prefix is just the URL for the site. -
Re4000w drops when trying to make initial connection to existing network
I am trying to set up a re4000w for a friend.
I am attempting setup through the browser, connecting to 192.168.1.1. No issues seeing their existing network, I am able to connect and enter a p/w and the device will attempt to connect to the exisiting AP. However, after 10 seconds or so, the connection completely drops and the default extender SSID dissapears and does not reappear. The browser window goes white.
I have hard reset numerous times. It was already runing 1.0 but I refreshed it. I have taken the device out of their home, and attempted to set up ay my own place and the same exact behavior takes place.
I know that the default gateway ay my place is 192.168.1.1, could this be creating some sort of comflict since the extender has the same default IP? I would think that once connected, the re4000w would grab a IP from the existing router and disable it own DHCP server.
Any ideas? ThanksIf you configured the RE to extend an exiting wireless signal, once configured it will drop it's default signal and start broadcasting the SSID it was configure to extend.
After the RE is configured the only thing you will notice on your wireless device is an increase signal for the extended SSID.
Have you used a extender as a repeater before or have they all been hard wired to the router as an AP?
Please remember to Kudo those that help you.
Linksys
Communities Technical Support -
Error message when trying to use bluetooth connections
Windows 7
Torch 9800 and Curve 8310 and Playbook
I'm trying to send using bluetooth to all of the above and get the error message "Abort FTP operaton, no services found"
I can see all the devices on the laptop, and on each device I can see the laptop.
Any help gratefully received, thanks.Hi Inedia,
Are you trying to send files from the computer to the BlackBerry® Torch™ 9800 smartphone, the BlackBerry® Curve™ 8310 smartphone, and BlackBerry® PlayBook™ tablet?
Currently Bluetooth® file transfer is supported only between 2 BlackBerry® smartphones. This KB article should provide more information. "How to transfer a file using Bluetooth technology between two BlackBerry smartphones"
http://bbry.lv/KNI0Rj
Thanks.
-FS
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click Solution? for posts that have solved your issue(s)! -
No RDS Servers at when trying to add to connection broker farm
Hello,
My client has 2 servers, Windows Server 2012 R2. One named "TW01" which is a Session-Host server, another called "RDSBROKER" (its actually called DC....-02, but i'll just stick to "RDSBROKER") which is a Licensing Manager, Web
Access and Connection Broker.
We would like to add TW01 to RDSBROKER's Connection broker farm. The problem is there are no servers to choose in the list.
I've attached a couple of pictures for your convenience.
Thank you.Hi,
Thank you for your posting in Windows Server Forum.
From your description it seems that you want to add the server to “configure load balancing settings”. For this you can perform as per below steps.
- After you have created collection, reach to collection page.
- Find “Host Servers” option (Last option)
- Click on Tasks > Add RD Session Host Servers
- It will display page to add the session host server; Add the specified server (in your case”TW01”)
- Click Next
- Click Add
- After this it will add the server to load balance setting box.
- Again open the “configure load balancing setting” and you will find your host server.
Snap:
Hope it helps!
Thanks.
Dharmesh Solanki -
Windows 8 crashes when trying to connect to a Remote Desktop or a VPN
Hello,
When trying to perform a connection to a remote desktop or a VPN the application crashes (either MSTSC.exe or Explorer.exe). I've noticed this happens when credentials are about to be asked (same happens when trying to access a restricted folder on a network
machine).
Useful PC specs:
- i7 3770k, 16GB Ram, GTX460 (2x-SLI) (Intel HD 4000 on board)
> All latest drivers and Windows updates installed.
> Ran Memory Diagnostic. No errors.
Event Log:
Faulting application name: mstsc.exe, version: 6.2.9200.16384, time stamp: 0x50108ae1
Faulting module name: DUI70.dll, version: 6.2.9200.16384, time stamp: 0x50108e6a
Exception code: 0xc0000005
Fault offset: 0x00000000000027ee
Faulting process ID: 0x994
Faulting application start time: 0x01cdf16f9b46e882
Faulting application path: C:\WINDOWS\system32\mstsc.exe
Faulting module path: C:\WINDOWS\system32\DUI70.dll
Report ID: dadcc27c-5d62-11e2-bf13-bc5ff4390e7a
Faulting package full name:
Faulting package-relative application ID:
WinDbg: (RDP Crash dump with procdump)
Loading unloaded module list
This dump file has an exception of interest stored in it.
The stored exception information can be accessed via .ecxr.
(994.1118): Access violation - code c0000005 (first/second chance not available)
dui70!DirectUI::Element::_SetValue+0xe:
000007fe`c5be27ee 488b01 mov rax,qword ptr [rcx] ds:00000000`00000000=????????????????
0:000> .ecxr
rax=000007fec5cbbd80 rbx=000000989f3afa28 rcx=0000000000000000
rdx=000007fec5cbbd80 rsi=00000000fffffffd rdi=00000098a3e805b0
rip=000007fec5be27ee rsp=000000989f23a8b0 rbp=0000000000000000
r8=0000000000000001 r9=000000989f3afa28 r10=0000000000000000
r11=0000000000000000 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=00000098a1d29401
iopl=0 nv up ei pl nz na pe nc
cs=0033 ss=002b ds=002b es=002b fs=0053 gs=002b efl=00010200
dui70!DirectUI::Element::_SetValue+0xe:
000007fe`c5be27ee 488b01 mov rax,qword ptr [rcx] ds:00000000`00000000=????????????????
0:000> !analyze -v
* Exception Analysis *
GetPageUrlData failed, server returned HTTP status 404
URL requested: http://watson.microsoft.com/StageOne/mstsc_exe/6_2_9200_16384/50108ae1/dui70_dll/6_2_9200_16384/50108e6a/c0000005/000027ee.htm?Retriage=1
FAULTING_IP:
dui70!DirectUI::Element::_SetValue+e
000007fe`c5be27ee 488b01 mov rax,qword ptr [rcx]
EXCEPTION_RECORD: ffffffffffffffff -- (.exr 0xffffffffffffffff)
ExceptionAddress: 000007fec5be27ee (dui70!DirectUI::Element::_SetValue+0x000000000000000e)
ExceptionCode: c0000005 (Access violation)
ExceptionFlags: 00000000
NumberParameters: 2
Parameter[0]: 0000000000000000
Parameter[1]: 0000000000000000
Attempt to read from address 0000000000000000
DEFAULT_BUCKET_ID: NULL_POINTER_READ
PROCESS_NAME: mstsc.exe
ERROR_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.
EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.
EXCEPTION_PARAMETER1: 0000000000000000
EXCEPTION_PARAMETER2: 0000000000000000
READ_ADDRESS: 0000000000000000
FOLLOWUP_IP:
dui70!DirectUI::Element::_SetValue+e
000007fe`c5be27ee 488b01 mov rax,qword ptr [rcx]
MOD_LIST: <ANALYSIS/>
NTGLOBALFLAG: 0
APPLICATION_VERIFIER_FLAGS: 0
FAULTING_THREAD: 0000000000001118
PRIMARY_PROBLEM_CLASS: NULL_POINTER_READ
BUGCHECK_STR: APPLICATION_FAULT_NULL_POINTER_READ
LAST_CONTROL_TRANSFER: from 000007fec5be7db8 to 000007fec5be27ee
STACK_TEXT:
00000098`9f23a8b0 000007fe`c5be7db8 : 00000098`9f23a950 00000098`00000004 00000098`9f23a954 00000098`9f3afa28 : dui70!DirectUI::Element::_SetValue+0xe
00000098`9f23a930 000007fe`b5378a73 : 00000098`a3f11208 00000098`9f23aa70 000007fe`b5418c58 000007fe`c4dc20f5 : dui70!DirectUI::Element::SetLayoutPos+0x98
00000098`9f23a970 000007fe`b53a5f7e : 00000098`a3f154d0 000007fe`b533bd54 00000098`a3ea80e0 00000000`00000000 : authui!UserList::_OnEnumerationSyncReply+0x689
00000098`9f23af80 000007fe`b5332670 : 00000098`a3f111f0 000007fe`b53212d1 00000098`a3f153a0 00000000`00000001 : authui!CCredDialog::UIJobEvent+0x15e
00000098`9f23afc0 000007fe`b533cf1b : 00000000`00000000 00000000`00000000 00000000`00000000 000007fe`cae3545f : authui!CEnumerationSyncReplyJob::DeferredExecute+0x20
00000098`9f23b000 000007fe`b533cfbc : 00000098`a3f111f0 00000000`00000001 00000000`00000000 00000098`0000029e : authui!CDeferredUIThreadJob::Do+0x37
00000098`9f23b030 000007fe`b53a7f42 : 00000098`a1d29350 00000000`000e0602 00000000`00000002 00000000`000e0602 : authui!CCredentialJobQueue::_ProcessJobs+0x69
00000098`9f23b070 000007fe`b53a7e76 : 00000000`00000000 00000000`00000000 00000000`00008003 00000000`00000000 : authui!CCredDialog::DialogProc+0xa2
00000098`9f23b0d0 000007fe`c86ab3b9 : 00000000`00000001 00000098`9f23b241 00000000`00008003 00000000`00000000 : authui!CCredDialog::s_DialogProc+0x66
00000098`9f23b100 000007fe`c86ab108 : 00000098`9f9522d0 00000000`00000000 00000000`00008003 00000000`00000000 : user32!UserCallDlgProcCheckWow+0x135
00000098`9f23b1d0 000007fe`c86ab02e : 00000000`00000000 00000000`000e0602 00000000`00008003 000007fe`c4dc120b : user32!DefDlgProcWorker+0xb8
00000098`9f23b2a0 000007fe`c869171e : 00000000`00000001 00000000`00000000 00000000`00000000 00000000`00000000 : user32!DefDlgProcW+0x56
00000098`9f23b2e0 000007fe`c86914d7 : 00000098`9f9522d0 00000098`9f23b4e0 000007f7`f30de800 000007fe`cae31b95 : user32!UserCallWinProcCheckWow+0x13a
00000098`9f23b3a0 000007fe`c86be067 : 00000098`9f9522d0 00000098`9f9522d0 00000098`9f9522d0 00000000`00000001 : user32!DispatchMessageWorker+0x1a7
00000098`9f23b420 000007fe`c86bc641 : 00000098`9f9522d0 00000098`9f9522d0 00000000`00000000 00000000`0000c000 : user32!IsDialogMessageW+0x242
00000098`9f23b4b0 000007fe`c86bb8a3 : 00000000`00000000 00000000`000909fc 000007fe`b53a7e10 00000098`9f3a6cd0 : user32!DialogBox2+0xfc
00000098`9f23b540 000007fe`c86bb936 : 000007fe`b5320000 00000000`000909fc 000007fe`b53a7e10 000007fe`b53a7df8 : user32!InternalDialogBox+0x113
00000098`9f23b5a0 000007fe`c86bbc1b : 00000000`00000000 000007fe`b5320000 00000098`9f3a6cd0 00000098`9f3a6cd0 : user32!DialogBoxIndirectParamAorW+0x56
00000098`9f23b5e0 000007fe`b53a7c91 : 00000000`00000000 00000000`00000000 00000098`9f3a6cd0 00000098`9f3a6cd0 : user32!DialogBoxIndirectParamW+0x1b
00000098`9f23b620 000007fe`b539d0d0 : 00000098`a1d29350 00000000`00000000 00000098`9f3ec310 000007fe`b7d77987 : authui!CCredDialog::Dialog+0x151
00000098`9f23b670 000007fe`b7d6d268 : 10458c33`00000029 00000098`9f23b800 00000098`9f3ebac0 000007fe`b7d6d370 : authui!CCredUI::CredUIPromptForWindowsCredentialsW+0x1dc
00000098`9f23b700 000007fe`b7d6d503 : 00000098`00000003 00000000`00000000 00000098`9f23ba10 00000098`9f3ebac0 : credui!CredUIPromptForWindowsCredentialsWorker+0x310
00000098`9f23b850 000007fe`ac10c4fd : 00000098`9f3ebac0 00000098`9f23baa0 00000098`9f23ba10 00000098`9f23ba28 : credui!CredUIPromptForWindowsCredentialsW+0x17b
00000098`9f23b8f0 000007fe`ac0a0a85 : 00000000`00000000 00000098`00000000 00000000`00000000 00000000`00000000 : mstscax!CTscCredentialsQueryUi::PromptForCredentialsNew+0x159
00000098`9f23b9c0 000007fe`ac09e8e8 : 00000098`9f362f38 00000000`00000000 00000000`00000000 00000098`a0fed860 : mstscax!CTscCredsAssistant::PromptForTsCredentials+0x4e5
00000098`9f23d050 000007fe`ac0a13f7 : 00000098`9f351050 00000000`00000000 00000000`00000000 00000098`a0f24d50 : mstscax!CTscCredsAssistant::AcquireTsCredentials+0x8f4
00000098`9f23d770 000007fe`ac0716fb : 00000098`a0f24d50 00000098`a0f24d50 00000000`00000000 00000000`00000000 : mstscax!CTscCredsAssistant::OnSecurityLayerNegotiationComplete+0x1af
00000098`9f23e000 000007fe`ac179428 : 00000098`00000002 00000098`a0f5fee0 00000098`a0f5fee0 00000000`00000001 : mstscax!CUI::OnSecurityLayerNegotiationComplete+0x11f
00000098`9f23e060 000007fe`ac179594 : 00000098`a0f1c540 00000000`00000000 00000000`00000000 00000000`00000000 : mstscax!CTSThread::RunQueueEvent+0x104
00000098`9f23e0b0 000007fe`ac17baf2 : 00000098`a0f1c540 000007fe`c8691742 00000098`a0f1bf30 00000000`00000000 : mstscax!CTSThread::RunAllQueueEvents+0xcc
00000098`9f23e110 000007fe`ac17bb28 : 00000098`a0f1bf30 00000000`00000000 00000000`00000000 00000000`00000000 : mstscax!CTSThread::OnNotifyThreadEventQueue+0xa6
00000098`9f23e150 000007fe`abefb451 : 00000000`00000000 00000000`00000000 000061f5`6df98991 ffffffff`ffffffff : mstscax!CTSThread::OnNotifyThreadMessage+0x20
00000098`9f23e180 000007fe`c869171e : 000007fe`c8691742 00000000`00000000 00000000`00035090 00000098`9f919f70 : mstscax!PAL_System_Win32_ThreadWndProc+0x19
00000098`9f23e1b0 000007fe`c86914d7 : 00000098`9f94fb70 00000098`9f23e320 000007f7`f30de800 000007fe`abefb438 : user32!UserCallWinProcCheckWow+0x13a
00000098`9f23e270 000007fe`c86bc6c4 : 00000098`9f950eb0 00000098`9f950eb0 00000000`00000001 00000000`0000c000 : user32!DispatchMessageWorker+0x1a7
00000098`9f23e2f0 000007fe`c86bb8a3 : 00000000`00000000 00000000`000909fc 000007f7`f331d518 000007fe`c81931b2 : user32!DialogBox2+0x219
00000098`9f23e380 000007fe`c86bb936 : 000007f7`f32c0000 00000000`000909fc 000007f7`f331d518 00000000`000909fc : user32!InternalDialogBox+0x113
00000098`9f23e3e0 000007fe`c86bbbe9 : 000007f7`f32c0000 00000098`9f23e4e0 00000000`000909fc 00000000`00000000 : user32!DialogBoxIndirectParamAorW+0x56
00000098`9f23e420 000007f7`f331d788 : 00000000`000909fc 00000098`9f23e570 00000098`9f23e4e0 ffffffff`ffffffff : user32!DialogBoxParamW+0x69
00000098`9f23e460 000007f7`f331ce9e : 00000098`a0efedc0 000007f7`f32c7ab0 000007f7`f333b420 00000000`00000000 : mstsc!CDlgBase::CreateModalDialog+0x168
00000098`9f23e500 000007f7`f32e2604 : 00000098`a0efedc0 00000098`9f23ead0 000007f7`f32c7ab0 00000000`00000000 : mstsc!CDlgBase::DoModal+0x12
00000098`9f23e540 000007f7`f32dbd6b : 00000098`9f4ec3e0 00000098`9f4ec3e0 000007f7`f32c7ab0 000007f7`f333b420 : mstsc!CDefaultContWndExt::OnConnectionIssued+0xec
00000098`9f23e9d0 000007f7`f3302bd9 : 000007f7`f32cbb00 000007f7`f32cbb00 00000000`00000000 00000098`a0f1f350 : mstsc!CContainerWnd::StartConnection+0x4d7
00000098`9f23ee70 000007f7`f3301feb : 00000000`000909fc 00000000`00000111 00000000`000c09be 00000000`00000001 : mstsc!CMainDlg::DialogBoxProc+0xbb9
00000098`9f23f1b0 000007fe`c86ab3b9 : 00000000`00000001 00000098`9f23f331 00000000`00000111 00000000`00000000 : mstsc!CMainDlg::StaticDialogBoxProc+0x63
00000098`9f23f1f0 000007fe`c86ab108 : 00000098`9f919f70 00000000`00000000 00000000`00000111 00000000`00000001 : user32!UserCallDlgProcCheckWow+0x135
00000098`9f23f2c0 000007fe`c86ab02e : 00000000`000c09be 00000098`9f23f500 00000000`00000111 000007fe`cae31b95 : user32!DefDlgProcWorker+0xb8
00000098`9f23f390 000007fe`c869171e : 00000000`00000001 00000000`00000000 00000000`00000000 000007fe`c8be1535 : user32!DefDlgProcW+0x56
00000098`9f23f3d0 000007fe`c86d22f9 : 00000000`000c09be 00000000`00000111 00000000`80000000 00000000`00000000 : user32!UserCallWinProcCheckWow+0x13a
00000098`9f23f490 000007fe`c869487a : 00000000`00000000 00000000`00000000 00000000`00000001 00000098`9f919f70 : user32!SendMessageWorker+0xa72
00000098`9f23f540 000007fe`c86bbdd3 : 00000000`00090a12 00000098`9f919f70 00000000`000909fc 00000000`000909fc : user32!SendMessageW+0x10a
00000098`9f23f5a0 000007f7`f3312409 : 00000098`a0ef0080 00000098`a0ef0080 00000000`00000000 00000000`03260475 : user32!IsDialogMessageW+0x40b
00000098`9f23f630 000007f7`f3312a07 : 000007f7`f32c0000 00000098`9f312374 000007f7`f333b420 000007f7`00000000 : mstsc!TSCMain+0x695
00000098`9f23f6e0 000007f7`f33319c9 : 00000098`9f313100 00000000`00000000 00000000`00000000 00000000`00000000 : mstsc!WinMain+0x42f
00000098`9f23f750 000007fe`c8fe167e : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : mstsc!ATL::AtlWinModuleTerm+0x375
00000098`9f23f810 000007fe`cae53501 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : kernel32!BaseThreadInitThunk+0x1a
00000098`9f23f840 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : ntdll!RtlUserThreadStart+0x1d
STACK_COMMAND: ~0s; .ecxr ; kb
SYMBOL_STACK_INDEX: 0
SYMBOL_NAME: dui70!DirectUI::Element::_SetValue+e
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: dui70
IMAGE_NAME: dui70.dll
DEBUG_FLR_IMAGE_TIMESTAMP: 50108e6a
FAILURE_BUCKET_ID: NULL_POINTER_READ_c0000005_dui70.dll!DirectUI::Element::_SetValue
BUCKET_ID: X64_APPLICATION_FAULT_NULL_POINTER_READ_dui70!DirectUI::Element::_SetValue+e
WATSON_STAGEONE_URL: http://watson.microsoft.com/StageOne/mstsc_exe/6_2_9200_16384/50108ae1/dui70_dll/6_2_9200_16384/50108e6a/c0000005/000027ee.htm?Retriage=1
Followup: MachineOwner
Any ideas what could be the problem and how to resolve this?Further proof it's something with credentials/authentication. I found a valid workaround, but I think this one's on Microsoft to actually fix.
I opened up Remote Desktop Connection, put in my username and clicked the Save Credentials box. Then I edited all the other settings. Saved the RDP connection to my desktop. Then I edited it with notepad, and added the password value. I found a blog that
provides a program that'll hash the password for you. I used it so I can say its safe:
http://www.remkoweijnen.nl/blog/2007/10/18/how-rdp-passwords-are-encrypted/
I put the hashed password in, saved the file. Then used it to connect and it worked. So by bypassing RDP having to ask for credentials, it didn't crash since it doesn't ask. Kind of inconvenient if you have many computers you have to connect in to. But for
those in a bind this will work for you.
This one worked for me, no update or installation of software before it broke, but had a "wife-poweroutage" (cable taken out) I'm just not in the mood to reinstall for this. But the above fixed it for me. Thank you! -
Ive gotten this when trying to update while connected to iTunes and when I tried to update through general.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Select
/var/log ▹ appstore.log
from the hierarchical list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar. Then select the messages from the last installation or update attempt, starting from the time when you initiated it. If you're not sure when that was, click the Clear Display button in the toolbar of the Console window and then try the installation again.
Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message (command-V).
If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Edit it out by search-and-replace in a text editor before posting. -
When trying to sign in to iCloud, I always get the message, iCloud has encountered a error while trying to connect to the server. How do I get in????
Hello,
Try following step and check if issue gets resolved or not.
Find Acrobat.exe on your computer. Right click the program and click 'Troubleshoot Compatibility'. Set the compatibility to Windows XP service pack 3.
Regards,
Anoop -
I keep getting an error message when trying to log on to FaceTime and iMessage on my iPad mini with wifi...Could not sign in. Please check your network connection and try again. Help!
Using FaceTime http://support.apple.com/kb/ht4319
Troubleshooting FaceTime http://support.apple.com/kb/TS3367
The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
http://tinyurl.com/a7odey8
Troubleshooting FaceTime and iMessage activation
http://support.apple.com/kb/TS4268
Using FaceTime and iMessage behind a firewall
http://support.apple.com/kb/HT4245
iOS: About Messages
http://support.apple.com/kb/HT3529
Set up iMessage
http://www.apple.com/ca/ios/messages/
Troubleshooting Messages
http://support.apple.com/kb/TS2755
Setting Up Multiple iOS Devices for iMessage and Facetime
http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
FaceTime and iMessage not accepting Apple ID password
http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
Unable to use FaceTime and iMessage with my apple ID
https://discussions.apple.com/thread/4649373?tstart=90
For non-Apple devices, check out the TextFree app https://itunes.apple.com/us/app/text-free-textfree-sms-real/id399355755?mt=8
Cheers, Tom
Maybe you are looking for
-
I will live in france for a year for a student exchange program. i want to buy an iphone 4 do i buy it in India? can i use it in france then? will it work? or should i buy it in france? will it then work in india? please help.
-
Calendar assignment in OAVH for '03' period control for calendar year dependent fiscal year.
Hi We have a year dependent Fiscal Year in our client's system. It is a 5-4-4 Fiscal Year variant starting from March till Feb. While trying to create a new asset we faced an error "You cannot save this asset(Correct depreciation error)." I checked a
-
After latest update total system slowdown
After installing the latest security update my system has slowed dramatically. The mouse pointer is jerky and sound stops and starts every operation has a time lag. I've repaired the permissions but this hasn't helped. Anybody else have this issue or
-
Ipod versus itunes - help, how can i avoid throwing my ipod against the wal
hi there i have recently splashed out and bought an ipod video. i was told it is user friendly - but how wrong was that? tried the website but the help is useless to me, then i sent numerous emails to ipod support without response. i have squillions
-
When I plug my USB into my MacBook, it doesn't detect. I don't see it popping up onto my screen. Help??