RE1000 - Refused to work with a WRT120N

This refused to work with a Lynksys WRT120N and Network Magic (Lynksys) could not find it. If you don't have a wireless laptop you can't get this junk to work.

I agree with Dibbler. It is important that you have the following before you try to sync your router with your RE1000:
* Wireless channel of your router
* SSID of your ruoter (your router's network name)
* the security settings, i.e. the kind of security you setup on your router (WPA, WPA2, WEP, etc.)
* Passphrase of your network
* Check if the Mac Filtering on your router is enabled. if it is, disable it.
Then you need to get the IP address assigned to your RE1000. Just access the GUI of your router, then go to Status > Local Network > DHCP Client table. It's listed beside "RE1000".
After that, access the RE1000 GUI using the IP you got from the DHCP client table.
Under Wireless tab, click Wireless settings. Choose Manual, then enter the following:
Wireless channel of your router.
SSID (wireless network name) of your router
Wireless security settings (passphrase, security type e.g. WPA, WEP, WPA2.)
Passphrase of your router or network password
Don't forget to save the settings.
Once you're done, go to Status (that's on your RE1000 gui), then check if it's already connected to the WRT120N. It should have an IP address, a default gateway and a subnet mask.
As for Network Magic, for as long as your RE1000 is properly configured with the information posted above, it should be detected by the Network Magic software. It should be visible in the network map.
Bottom line is, IT'S ALL IN THE SETTINGS OF YOUR RE1000 and your router.
But if all that fails, try upgrading your router's firmware. It could be that your router's firmware is not upgraded, hence, the connectivity issues.
Hope this helps.
"Don't fix it if it ain't broken."

Similar Messages

945GCM478 refuses to work with ATI HD5750!?

Hi everybody.
I own the MSI 945GCM478 since October 2008 and I was pleased with it, but now I'm facing a problem.
Recently I've bought a Gigabyte GV-R575D5-1GD graphic card (using ATI HD5750 chip), which does not work with MSI motherboard. The graphic card works fine on other motherboards (tested).
But with 945GCM478, I power up the system, all coolers start spinning, but after 5 second they stop, only to restart again after 1 second, and so on ...start, stop, start, stop. The graphic card does not display anything in this time. So what does a reasonable person think in this situation... the power supply isn't up to it (although I've read that this graphic card isn't very demanding)! So I get angry and buy a Nexus RX-8500 PSU which should be enough I thought. But to my stupefaction the behavior of the system was the same. I've tested other 2 PSU with the same results. On the same occasion I also tested a nVidia GeForce 9500
graphic card which worked fine. Also two months ago I tested the system with a GeForce 9800GT graphic card ... no problem.
In the mean time I've updated to v1.1 bios... so this could be a problem. I reverted to v1.0 bios and tried again... no results.
I don't know what else to try.
So I'd like to ask if anybody have experienced anything similar, or can drop some light on the issue.
Could be a bios/chipset/PCI-E problem, or my motherboard is just faulty?
Is there any solution to make the HD5750 to work with 945GCM478?
The system uses a 3GHz Pentium 4 which complies to the minimum requirements in the graphic card manual.
Thank you in advance for any suggestion. (Please excuse my English).

i.
The system consist of
Motherboard: MSI 945GCM478;
Processor: Intel Pentium 4 HT (Prescott,FSB800,1MB);
RAM: 1GB x 2 Kingston 800MHz (running in dual channel at 667MHz);
HDD: Western Digital 160GB SATA2, Maxtor 200GB SATA1;
OPTICAL: DVD-RW LG;
PSU: Nexus RX-8500
AC Input    115V/230V 15A/7,5A 50/60Hz
DC Output        +3.3V   +5V   +12V1+12V2+12V3+12V4   -12V   +5VSB
Max Output Current   24A   30A     20A     20A     20A 20A   0.8A   3A
Max Combined Power     170W      760W              6W   15W
Total Power          829W
Also I would like to mention another thing, which raised my suspicion at first:
before I tested the graphic card on my home system I tested it on job system, a Lenovo using Intel 946PL/GZ chipset / Intel Pentium D 925 (LGA775) / 1GB DDR2 667. Initially this system refused to boot also with the graphic card, producing several beeps. It did started only when I set in the the bios the active video device as Internal (not Auto or PCI-E) but the inserted graphic card didn't displayed anything, although the cooler was running.
I hope this helps.
Thank you.

T400 - crappy USB ports and refusing to work with HP keyboards

Hello forum,
I work in a large multinational company and all of our laptops are now IBM Thinkpads from T60's, T61's, and now of course they're Lenovo T400 and T410 laptops.
Also we still have some of the Thinkcentre towers.
There seems to be other people with the same problem where the weak plastic / incorrectly sized ports are causing problems.
Well i've just had my 4th Lenovo laptop cause problems and so far they've all be T400's or T410's with the exception of one Thinkcentre.
Each time there is a problem its because the crappy plastic they used to make the usb port pin protector has snapped off except in the case of the Thinkcentre PC.
The problem is that the vast majority of our keyboards are the basic HP keyboard and all of a sudden the keyboard stops working with the laptop.
The keyboard could be working fine for weeks months or days and then all three lights will light up at the same time on the keyboard (num lock, caps lock and scroll lock) and the keyboard will no longer function.
The only work around for the problem is to swap out the keyboard with an older Fujitsu Siemens Keyboard, or if i can find one an actual Lenovo keyboard.
Do some lenovo systems have an allergy to HP keyboards?
Or could someone tell me if theres a different cause for this problem.

which HP keyboards are you talking about? there are quite a few different model of HP keyboard used by businesses.
Also, is this problem caused by one keyboard or multiple HP keyboards?
Keyboards should be designed with interoperability, but sometimes a usb could be badly designed where it pinches the usb ports.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

ICloud refuses to work with me.

I know this question has been answered before, and I've even read some replies. But nothing seems to be working.
I simply want applications like iCal, Reminders, Notes, etc. to sync properly from Macbook to iPhone.
It never wants to synchronize. Am I missing a step? It used to work but now it doesn't?
I've totally signed out of iCloud on both devices, and signed back in. But still nothing.
I've even had weird problems where two events overlap on iCal and when you go to delete them, they reappear instantly.
I'm signed into the same iCloud account on both devices.
Any suggestions? Thank you.

i.
The system consist of
Motherboard: MSI 945GCM478;
Processor: Intel Pentium 4 HT (Prescott,FSB800,1MB);
RAM: 1GB x 2 Kingston 800MHz (running in dual channel at 667MHz);
HDD: Western Digital 160GB SATA2, Maxtor 200GB SATA1;
OPTICAL: DVD-RW LG;
PSU: Nexus RX-8500
AC Input    115V/230V 15A/7,5A 50/60Hz
DC Output        +3.3V   +5V   +12V1+12V2+12V3+12V4   -12V   +5VSB
Max Output Current   24A   30A     20A     20A     20A 20A   0.8A   3A
Max Combined Power     170W      760W              6W   15W
Total Power          829W
Also I would like to mention another thing, which raised my suspicion at first:
before I tested the graphic card on my home system I tested it on job system, a Lenovo using Intel 946PL/GZ chipset / Intel Pentium D 925 (LGA775) / 1GB DDR2 667. Initially this system refused to boot also with the graphic card, producing several beeps. It did started only when I set in the the bios the active video device as Internal (not Auto or PCI-E) but the inserted graphic card didn't displayed anything, although the cooler was running.
I hope this helps.
Thank you.

Missing Sync refuses to work with iSync

My Missing Sync (version 5 for Palm) can see my Palm via USB and all other conduits (AvantGo, TimeSync, Photos) are syncing without incident.
However, it refuses to play nice with iSync.
• iSync is enabled in the list of conduits.
• Palm Syncing is enabled in the iSync app.
• A Palm device is listed in iSync and contact and calendar items are selected for syncing (selectively confining the sync to contacts or calendar items only does not fix this problem)
• I disable all other conduits (which work, but to be sure) and leave only the iSync conduit active in Missing Sync.
• I attempt a sync. The Palm chimes and its screen shows a sync in progress.
• The Missing Sync program also changes to show a sync in progress but then NOTHING HAPPENS. After 5 minutes the Palm device times out, and Missing Sync, despite the two constant barber-poles, becomes unresponsive. Even trying to cancel the sync by clicking the cross in MS is useless, which means I can't even check a log file to see where the problem is. I am forced to force-quit MS and relaunching reveals no iSync data was synced.
I have tried:
• Hard resetting the Palm
• Forcing the Mac to overwrite the Palm
• Clearing the iSync cache data and preference files.
• Repeatedly toggling the iSync conduit.
The main problem is the lack of feedback from Missing Sync about why the connection is hanging, or even what it is attempting at the point the process fails. The iSync log reveals it was "connected" but says no more than that. The Sync History log in MS reveals a sync operation starting and then nothing more.
Obviously the Palm and the Mac can see each other, and as I said, all other conduits work perfectly.
I note the following entries in this logfile at the point things fall over:
console.log:
2007-07-19 17:15:36.512 Conduit Manager[270] CFLog (21): Cannot recognize type of executable for CFBundle 0x35d6f0 </Library/Application Support/Palm HotSync/Conduits/Apple> (not loaded)
Jul 19 17:15:37 Nathan-Zamprogno crashdump[271]: PowerPCCompatibility crashed
Jul 19 17:15:37 Nathan-Zamprogno crashdump[271]: crash report written to: /Users/localadmin/Library/Logs/CrashReporter/PowerPCCompatibility.crash.log
I would suggest that this error message suggests at the cause. Has anyone else had this experience? Can anyone help?
Thanks.

I guess I simply cannot fathom why you would want to synchronize a Palm device under Mac OS X 10.4.x using the iSync Palm Conduit instead of the Mark/Space Contacts, Events and Tasks conduits supplied with the Missing Sync for Palm OS? What can this possibly achieve?
And, despite your report that the iSync Palm Conduit is active, this error entry shows that it clearly is not: Cannot recognize type of executable for CFBundle 0x35d6f0 </Library/Application Support/Palm HotSync/Conduits/Apple> (not loaded)
Apple is the Finder name of the iSync Palm Conduit. It appears in your Missing Sync—or alternatively, HotSync—conduit list simply as iSync Conduit.
Why not simply configure the Missing Sync to use its own specialized contact, event and task conduits and ditch the iSync Palm Conduit?

The HTC One M8 is a lemon and Verizon refuses to work with us.

We are now awaiting shipment of a FOURTH HTC One M8. First purchased on release day and returned within a week per store suggestion due to roaming bug (fixed with software update later). Second phone randomly turns off, restarts, freezes and doesn't respond. Verizon made us warranty replace this one as it was just past the 14 day mark of the initial purchase (we weren't thrilled). Now the third phone exhibits same behavior as second. Was supposed to get call from Verizon support manager yesterday following up on their insisting that an app was causing it, but she never called like she assured she would. We had removed ALL downloaded apps and still had phone turn off randomly. Verizon now refuses to do anything but send us a reconditioned phone as another replacement. This is the first and last HTC device we will ever try and most likely will begin looking for another carrier as Verizon clearly doesn't care about solving it's customers problems. If they expect me to pay full price for a reconditioned phone they're a joke. I'm awaiting a phone call from someone in management within 24-48 hours to discuss this all further.
Do yourself a favor and avoid this garbage phone!

"You have a warranty which states replaced with certified like new and not brand new."
This would be understandable and acceptable if it was for the fact that since day 1 we've been given broken phones.I refuse to pay full price for something that has been broken since the start.
I've spoken with HTC and received the "this issue hasn't been reported" statement and it pretty much went nowhere. One option was to send the device to HTC and wait for them to figure it out and send it back, but with no backup phone (turned in for credits) to use and my wife using this for work that's not a viable option.

15" Powerbook 1GHzwith UJ-815 refuses to work with ANYTHING

I have been reading the uj-816 article with interest (as I have the UJ-815) and have tried everything and still doesnt work, it attempts to read whatever disc I put in (including the system disc) about 3 times then spits it out. Im running 10.4.7 and have repaired my HDD with disc utilities. Ive made sure that I had the D0CB latest firmware, Ive reset the PRAM, used MacJanitor...... what do I do?
Also although my mac now registers my HP Laserjet 1020 as being connected, it refuses to load the driver that I downloaded from the HP website.......
HELP ANYONE!!

I wouldn't say it doesn't bear repeating, regardless of how bone headed it may seem. It works, but as in all cases, beware and ymmv.
I was just searching for help on the same topic -- the uj-815 slot drive that I had placed in my pismo a few years ago just up and refused to accept a cd or dvd, an dthis happened moments ago. I'd been importing maybe 2 hours of lectures from disc when it simply would not take the third and final cd after I'd ejected the 2nd one as I always do, by clicking on the arrow in the finder. When it wouldn't take the cd, I restarted - still wouldn't take it. Then I let the system cool down (shut down iTunes and all other apps for whatever good that would do), searched the boards here for answers for 15 minutes, then tried to insert again - nothing doing.
When I searched the boards, I came across this thread and another where someone had inserted a card or paper inside which seemed to trigger stuck something or other. Very technical solutions, right up there with the old banging the tube on the side to get a picture. In my case, the uj-815 offered resistance to any cd or dvd I tried to slide in. Because I have a pismo (G3 firewire powerbook), I just popped the latch and removed the slot loading drive, gave it a couple of firm taps on the bottom and slid the drive back in to the pismo. Guess what - presto! It works again. I just burned the last lecture while typing this out.
In my case (with an easily removeable drive) it wasn't bone headed, it was a no brainer. I'm glad it was repeated because it helped in my case, with no risk of damage to my hard drive. Don't know how comfortable I'd be if I couldn't remove the drive first, but there it is.

My iTunes is refusing to work with any device I attach to my computer: iPod, iPad and iPhone. I've tried everything recommended to me by Apple, but nothing has worked, not even several uninstallments of iTunes. Help please!!

All my computer says is that it reconises that there's a iPod there but that it can't use it for some reason.
All of the solutions offered have not worked. I just want to be able to use my iTunes properly again.

Hello, Beckara.
Thank you for visiting Apple Support Communities.
I would need some clarification on the issue you are experiencing to better assist you. However, if your device is not recognized by iTunes, I would recommend the steps in the article below. Start with the section labeled Verify that the Apple Mobile Device USB Driver is installed > For Windows Vista, Windows 7, and Windows 8 > Update the Apple Mobile Device Driver.
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
If iTunes becomes unresponsive when connecting a device, try the troubleshooting steps in the article below.
iTunes: May become unresponsive when connecting iPhone, iPad, or iPod touch
http://support.apple.com/kb/TS3219
Cheers,
Jason H.

My MacBook pro refuses to work with my Kodak esp 3.2s?

i have bought a MacBook over a month ago i have got it checked out their are no issues with it what so ever. However the Kodak printer i have tried connecting wireless but still will not work even when i try to use t with a wired connection it still won't... plz can someone help me ASAP!

Hello Sohail3261,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
Troubleshooting printer issues in OS X
http://support.apple.com/kb/ts3147
Best of luck,
Mario

Adobe Creative Suite CS4, printer, dongle ALL refuse to work with Mavericks

I have made the disastrous mistake of 'upgrading' to OS X 10.9 Mavericks. Now my HP printer won't work. My 4G dongle with my laptop no longer works and EE can't help at all with finding a suitable driver. And my Adobe Creative Suite CS4 is no longer compatible and isn't even supported any longer. So my 27-inch iMac is now just a piece of worthless junk.
Can someone please advise?

I think you'd be much better off asking in the Acrobar forum, Acrobat

LaPastenague can you help? TC is refusing to work with existing modem/router

My home office network setup is driving me mad! I've identified the issue - my TC is competing with my modem/router. What I haven't been able to do is fix the problem. I've tried setting it up as a bridge, tried turning off wireless and nothing has worked. Are you able to help before I throw an almighty tantrum?
Here's my set up:
* Primary computer is a MacBook Air which is on wireless 24/7
* Secondary computer is a MacBook Pro, also operating on wireless
* Time capsule is used as a server of sorts, to store all our files which are then accessed via the laptops. It's only a few months old.
* Router is also new (yes, someone sold us incompatible devices). It's a Netgear D6200.
* We've set up both a 5G and a 2.4G wireless network, but operate on 5G 99% of the time
* There are 2 x Airport Express in the house - one connected to the printer, one connected to the surround sound system
* There are also 2 x Apple TVs and 1 x iPhone connected to the network
Are you able to help me figure out the best setup? I know it's possible - I just can't figure out how to do it

I presume the modems you've suggested are all compatible with my apple devices? I read somewhere amidst your recommendations that apple doesn't play nicely with non-apple modem/routers.
Depends on brands.. Netgear is near the bottom.. overall TP-Link is pretty good.. they are certainly aware of the need to test against Apple products and special protocols, and tweak here and there to get better results.
It is important to understand though.. what I want you to do is basically turn the modem router into a dumb modem.. it will have no part in the network other than translation of ethernet packets to ATM phone networking packets. All the routing will be handled by the Apple router.
Yes, the Netgear is a wifi/DSL modem & router. I'm using wireless on the Netgear. I didn't turn wireless off on this device as I assumed I should be relying on that as my router given it was recommended instore. I'll give that a go now.
Shakes head::
Never ever believe what the salesman in the store tells you. He always has one at home that works perfectly with every piece of equipment you happen to have. And it fixes warts and herpes.. and most everything.. the bottle says snake oil. Apply liberally to dumb customers.
The reason I suggest a very cheap modem.. is that it will do nothing .. except translate packets. Ethernet to ATM.. ATM to Ethernet.. completely dumb.. You can bridge the Netgear but that seems a horrible waste.. I would prefer you to return it to the store for refund.. or at worst sell it off..
Even if you need to use it as a router.. which we are still getting to.. there is no need to use its wireless.
Anyway keep in touch with how it goes.
Are you in Oz? Who is your ISP?

Mac Mail refuses to work with exchange

I have a 2010 MacBook Pro with Snow Leopard. My job uses Outlook Web Access for e mail, but it goes to my iPhone and iPad just fine. I tried setting up the same exchange settings on Mail 4.3. It completely destroyed my program. I had imap gmail set up in Mac Mail and both accounts refused to send or receive any e mail at all. I deleted both and emptied my cache (essentially resetting mail to factory) and set up just the exchange account. It connects to pop and smtp, but refuses to send or receive anything. I don't even get the rotating circle that it's even trying. I've had to dump the program and use Entourage, which I hate.
I really want to use Mac Mail is there anything else I can do? My IT department is pretty unknowledgable when it comes to Macs.

Anyone? I'm now using Outlook and it's worse.

Why does firefox refuse to work with nortons 360 program? started with firefox ver 3.5!

ortons tool bar does not come up in firefox is launched. but does in ms explorer and google chrome.
== This happened ==
Every time Firefox opened
== I downloaded ver 3.5 of firefox

Go to Tools|Options|Applications. The first 4 entries relate to Adobe. Make sure that the association is for your 9.1 version. If it's not, click the association that is showing. You will get a downward pointing triangle at the right. Click on it and see if 9.1 is listed. If so, select it. Do the same for the other Adobe items.
You might also want to check "Folder Options" in the Windows Control Panel. In the "File Types" tab you will find all of the file extensions and the programs they are associated with. Scroll down to the PDF extension and insure it's associated with an "Adobe Acrobat Document. If not, click on the <change> button and find adobe in the program list.
Just to let you know, Adobe Reader is now up to version 9.4. You can go to Adobe's website to download the latest.
davewdan

Safari 6.2.2 refuses to work with Java 1.8 (Mac os 10.8.5)

I have Mac os 10.8.5. Safari 6.2.2 isn't able to utilize Java. I install the latest version, 1.8 (version 8, update 31), but it simply isn't recognized when I try to use a site that requires Java or when I go to the Java test page. When I use the Java test page, the plugin isn't found and I am told to download and install Java, which I already did.
How do I force Safari to recognize Java?

There's another way.
Right or control click the + then click Remove Item.
Just remembered that keyboard shortcut!
You're welcome

Why does Discover Card Secure number and Kentucky Unemployment refuse to work with Firefox?

When attempting to access the site below, the message,Your browser is not currently supported for this site. For more information, view.
the browser compatibility information on this welcome page. shows up and blocks further access.
When attempting to use Discover Card's Secure Number app, it does not ever find open forms to fill.
What can we do to repair this problem?
thank you for your help.
[email protected]

That is due to limitations on that site. In their browser support comments they state that they only support IE, the warning message that you get is because it detects that you are not using IE.

RE1000 - Refused to work with a WRT120N

Similar Messages

Maybe you are looking for