Read Verify Scan Message on Screen

I started my ipod this morning and got some kind of diagnostic screen, which I tried to negotiate through and now it is completely locked up and says:
Read Verify Scan
Scan takes a while
Battery Check
Volts=476
Level=10
Canceled
MENU to continue
Although pressing menu does nothing and plugging into the computer, it's not recognized. Does anybody know what this screen means?

yes, it means u are in diagnostic mode. I think because u canceled it, it may have frozen up. Try holding menu and center for 6-10 seconds. post back

Similar Messages

  • I NEED HELP!*weird menu setup thing white screen"read verify scan"*

    basically...my dad had to delete everything off the computer and install everything back on again. i installed itunes, and the ipod setup thingy u have to do. when i plugged my ipod in and switched it on it came up with a white screen with a menu on it i havent seen before. i started setting my ipod up throuh the menu, and it has now reached a screen and at the top it says "Read Verify Scan scan takes a while" below that it says:
    Battery Check
    Volts=508
    Level=10
    Charge Ok !
    3999488
    99%
    it has been on this screen for a while now. i cant switch it off, and if i unplug it the volts and level number decreases. should i leave it plugged in or unplug it, or what else should i do?? i hope you can help me with this problem.

    Here:
    http://www.apple.com/ipod/specs.html
    Video
    Video formats supported: H.264 video, up to 1.5 Mbps, 640 by 480 pixels, 30 frames per sec., Low-Complexity version of the H.264 Baseline Profile with AAC-LC audio up to 160 Kbps, 48 kHz, stereo audio in .m4v, .mp4, and .mov file formats; H.264 video, up to 768 Kbps, 320 by 240 pixels, 30 frames per sec., Baseline Profile up to Level 1.3 with AAC-LC audio up to 160 Kbps, 48 kHz, stereo audio in .m4v, .mp4, and .mov file formats; MPEG-4 video, up to 2.5 Mbps, 640 by 480 pixels, 30 frames per sec., Simple Profile with AAC-LC audio up to 160 Kbps, 48 kHz, stereo audio in .m4v, .mp4, and .mov file formats

  • Read Verify Scan issue

    I've been havings some problems, so I decided to go through the diagnostics. I am now at Read Verify Scan screen for HDScan test, and it says "Start Scan....". Its been sitting there for a long time! How long does this take? I've tried hitting the Select, but nothing happens?!

    I've been havings some problems, so I decided to go through the diagnostics. I am now at Read Verify Scan screen for HDScan test, and it says "Start Scan....". Its been sitting there for a long time! How long does this take? I've tried hitting the Select, but nothing happens?!

  • Read Verify Scan Weird result "11ror!"

    Had some problems with my ipod for no real reason, never droped or anything, but the other day stopped responding totally. After leaving it on charge over night managed to at least to get it to show sad ipod face, or sometimes the folder icon. After about 40 trys managed to get it into diagnostic mode. Ran the Read Verify Scan in th IO harddrive option, and it returned the result of 11ror!. I am guessing that this basically means the harddrive is screwed. The computer wont even recognise that it is attached at all.
    Rich

    The Sad iPods icon, clicking sound or folder with an exclamation mark are the toughest problems to deal with, and must do a Restore in order to fix it. However, when your iPod is showing this icon, it is probably too late for your computer to recognize the iPod.
    1. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
    http://www.apple.com/support/ipod/five_rs/
    2. Try to put the iPod into Disk Mode if it fails to appear on the desktop
    http://docs.info.apple.com/article.html?artnum=93651
    Still can't see your iPod?
    Several things could keep iPod from appearing in iTunes or in the Desktop/Finder when you connect it to your PC/Mac. The most likely causes are listed below in logical order. Check from the top of the list to see if that is what's keeping iPod from appearing.
    3. Try to wait 30 minutes while iPod is charging.
    4. Try another known-good FireWire or USB through Dock Connector cable.
    5. Try another known-good FireWire or USB port on your computer .
    6. Try to disconnect all devices from your computer's FireWire and USB ports.
    7. Windows users having trouble with their iPods should locate a Mac user. We've found that in many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
    There are also some cases being reported that some unrecognized iPod being able to be erased with Linux, then reconnect the iPod with the original computer and do a Restore there.
    8. Try to do an Erase (Disk Utility) on a Mac computer or a format with a PC (Disk Management tool) but ensure you choose the right Drive (your iPod not your Hard Disk of your computer). You may need to plug and unplug your iPod with the computer for several attempts, and switching around Format and Restore, and hope out of sudden, it will get recognized.
    9. Diagnostic mode solution – which I copied from a thread of a post from thinktwice
    “Then I cam across this special Diganostics Mode that you can get to by resetting and then while the Apple is showing pressing the Select and backwards keys simultaneously. It bring up and weird Diagnostic utility witha a abunch of tests. Here is what I did
    - I tried the 5in1 test and got and error on Firewire.
    - I did the HDD R/W and surprisingly it passed.
    - I went on to the HDD scan. This supposedly tkaes acouple of minute so I waited. I think 4-5 dots appeared then nothing. The iPod started to get hot. THe disk was spinning away. After a while the battery got very low. THis test chews up the battery. So I escaped out by resetting and went to connect it to a power source.
    My USB was dangling out of my computer and I was too lazy to get the Firewire AC adapter thing going so I connected expecting the whole lockup thing with iTunes. Surprise. IT was recognized immediately and has been working like a champ. So go figure.
    Details on Diag mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/index.shtml
    10. Let me ask you a question, if an iPod with no iPod software with it. When your connect it with a computer, what would happen?
    Yeah, the computer will treat it as a fresh external hard disk, which will get force mounted, the computer will ask you to format the iPod. It does not really matter the format is completed or not, the key is to erase (or partly) the corrupted iPod software on the iPod, after that the computer will recognize it.
    Once it has been completed, eject your iPod, open the iPod updater and interestingly, you will able to do the Restore this time.
    Base on the above, that's why I suggest Windows users who experience trouble with their iPods should locate a Mac machine or vice versa. PC computer will not recognize a Mac formatted iPod, but it will get mounted in an attempt to format your iPod.
    11. Put your iPod in disk mode and plug with a computer, and have a boot of your computer using the Mac OS or XP startup disks, hope that your iPod will be seen on Mac's Disk utility and allow you to do a Erase there. Or, under the XP, you will be able to find your iPod there for you to do a Restore.
    But, if none of these steps address the issue, your iPod may need to be repaired. You can arrange for service at the iPod Service Website.
    I have just read an interesting solution about the Sad iPod, it does make sense but the warranty will be waived once you open the iPod, I would not do it myself as I am not good on doing this
    http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
    Pictures and instructions of how to open the iPod case for battery replacement
    http://www.kokopellimusic.us/KM_instructions.htm

  • Nano stuck on error msg: Read Verify Scan

    I may have posted my original post in the wrong thread, so I thought I'd post here.
    I turned on my iPod Nano and have some sort of a frozen scan screen that is at 0%. It has this information on the screen:
    Scan takes a while (all day now is a little too long I'd say :D)
    Battery check
    Volts=478
    Level=10
    Charge OK !
    Canceled
    0%
    Tried to reset, but screen is frozen in this scan position
    Tried turning off or on - screen frozen
    Tried hold on and off - screen frozen
    Tried the update:
    I thought maybe an update would get things moving along, but when I connect to my PC I don't get the connection logo, and the iPod just remains in the frozen scan state, a scan this is not working anyway.
    IN other words, I have a frozen error message and I can't do anything with the iPod.
    Anyone ever have this problem?
    And it's not like it's never been connected - it has - and I've never had any problems. This is the first.
    Sony Vaio Windows XP Pro

    As I mentioned in my original post:
    Tried to reset, but screen is frozen in this scan position
    Tried turning off or on - screen frozen
    Tried hold on and off - screen frozen
    Tried the update
    Tried restore
    Tried connecting to PC
    But nothing will budge that error message on the screen. Looks like it's a major technical problem with the iPod Nano.
    Sigh.............

  • Read Verify Scan

    What is this??? My husband turned it on and this is what it says. It now says...Battery Check
    Volts=456
    Level=9
    Charge Ok!
    Canceled
    MENU to continue
    Well, I press menu and nothing happens. I have tried everything I know how to. Help a sister out!

    See this.
    How to reset the iPod.
    It may take quite a few attempts and is best done connected to power.

  • My screen is frozen, have verifying document message and can't get rid of it

    While adding some books I received a 'verifying document' message over the top of my library screen. I cannot get rid of it, the entire screen has frozen. I uninstalled and reinstalled, but it reinstalled the same. Help?

    Have you tried a reset ? Press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider if it appears), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

  • On closing Photoshop CC, I am getting an error message on screen that read's "Selective Palette error: no element found at line 1. Are you able to assist with this problem?

    Can anyone shed some light on this error message I am getting upon closing Photoshop CC
    I am getting an error message on screen that read's "Selective Palette error: no element found at line 1. Are you able to assist with this problem?

    Same issue here in WI and for me it was at 6:36p CST.
    I'm changed my password, removed iCloud from my phone ... tried 3G and WIFI with no luck. I also cannot check it on my Mac or iPad. I was able to get contacts and calenders back on my phone but no mail yet.
    Did the whole Apple support thing and apparently I'm part of the 1%
    EDIT: Question: are all of you former MobileMe users as well? Just wondering because I know there were going to be some changes as they completely move MobileMe over to iCloud and drop the "extra" services. I just can't remember if it was just a single cut off date or a series of dates. THAT email is stuck in my iCloud folders.

  • Screen icons are huge.  I can't read my text messages and the whole screen page won't display.  How do I restore the phone screen to it's natural setting?

    Screen icons are huge.  I can't read my text messages and the screen page won't fully display to view. How do I restore the phone screen to it's natural setting.

    Thanks.

  • I am now unable to print pdf documents. The message on screen says I have not selected any pages to print, even though the bullet point saying 'All' pages  has been clicked. I have recently upgraded to adobe reader XI, could that be the problem? I also ca

    I am now unable to print pdf documents. The message on screen says I have not selected any pages to print, even though the bullet point saying 'All' pages  has been clicked. I have recently upgraded to adobe reader XI, could that be the problem? I also cannot sign in to Adobe Export pdf now either. It says 'error occured while signing in'!

    Open Adobe Reader | Edit | Preferences | Documents: change View Documents in PDF/A Mode to Never.
    Regarding the ExportPDF problem, please start a new topic in the ExportPDF forum.

  • Left for vacation 5.27: firefox was accessible / returned from vacation 5.31: message on screen reads "unable to access server", "does not recognize server"

    left for vacation 5.27: server was accessible / returned from vacation 5.31: message on screen now read: "does not recognize server" / this is for both internet & email access
    == This happened ==
    Every time Firefox opened
    == i turned on my personal computer / this condition has remained for two days

    I realise this doesn't help you but I have reported this exact same issue (well, the part about being unable to login to webmail from abroad anyway) for MONTHS and all I get told is 'well you SHOULD be able to login'. I am no further forward and have come to the conclusion the only way to resolve this is to change ISP/phone provider.
    I had to create (and pay for) a domain with 1and1 in order to be able to send and receive e-mail while abroad, I didn't want to use Gmail or the like.
    As you say, it is INCREDIBLY FRUSTRATING, especially when I work for at least 6 months of the year overseas and BT just seem to ignore these posts.
    My trace is:
    1 1 ms 3 ms <1 ms 172.16.0.1
    2 1 ms 4 ms 16 ms 192.168.40.30
    3 3 ms 20 ms 3 ms 37-225.rv.ipnxtelecoms.com [62.173.37.225]
    4 15 ms 13 ms 16 ms 41-184-126-13.rv.ipnxtelecoms.com [41.184.126.13]
    5 109 ms 117 ms 109 ms ir2-th-lon.rv.ipnxtelecoms.com [41.184.56.101]
    6 109 ms 111 ms 153 ms tel-2.ccr01.lon09.atlas.cogentco.com [149.6.98.33]
    7 113 ms 110 ms 182 ms te0-0-0-2.ccr21.lon01.atlas.cogentco.com [154.54.36.165]
    8 109 ms 170 ms 167 ms bt.lon01.atlas.cogentco.com [130.117.14.170]
    9 116 ms 114 ms 111 ms 166-49-214-175.eu.bt.net [166.49.214.175]
    10 122 ms 115 ms 139 ms core2-te-0-3-0-1.ilford.ukcore.bt.net [62.172.102.14]
    11 113 ms 122 ms 112 ms core2-pos1-1.birmingham.ukcore.bt.net [62.172.103.93]
    12 118 ms 121 ms 117 ms iar1-gig5-5.birmingham.ukcore.bt.net [62.6.196.98]
    13 115 ms 117 ms 115 ms 62.172.57.218
    14 * * * Request timed out.
    15 * * * Request timed out.
    16 * * * Request timed out.
    17 * * * Request timed out.
    18 * * * Request timed out.
    19 * * * Request timed out.
    20 * * * Request timed out.
    21 * * * Request timed out.
    22 * * * Request timed out.
    23 * * * Request timed out.
    24 * * * Request timed out.
    25 * * * Request timed out.
    26 * * * Request timed out.
    27 * * * Request timed out.
    28 * * * Request timed out.
    29 * * * Request timed out.
    30 * * * Request timed out.
    Trace complete.

  • How do i get rid of original loaded message on screen on l7680

    how do I get rid of original loaded message on screen of my L7680

    Hi...
    pls do these steps to reset your printer back to factory defaults....
    Hope this will work...
    1. while  the printer is on- unplug the power cord.
    2. when the printer switched off- pls press and hold 3 and # key buttons while reconnecting the power cord back to the printer.
    3.when you see a message " Improper shutdown" just press ok to continue
    4.select your appropriate language and country to continue
    5. wait the printer to initialize.
    6. When you see the normal screen, reconnect the printer again back to the wireless network using the wireless set-up wizzard from the printer's control panel.
    7. Try to print and scan wirelessly.
    Although I am working on behalf of HP, I am speaking for myself and not for HP.
    Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
    If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
    Happy Troubleshooting : )

  • Cannot remove warning message from screen

    I work remotely and use Outlook Web App to access my emails.
    Everything works fine other than I always get this warning message:
    which I cannot remove as the 'Continue' option is unresponsive to clicks.
    Anyone have any ideas how to cure this??
    Many thanks.

    The server has a self-signed certificate, which means that the people in charge of it don't know how to do their job. That's not a problem I can help you with. However, the warning dialog should not be unresponsive.
    Please read this whole message before doing anything.
    This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
    Step 1
    The purpose of this step is to determine whether the problem is localized to your user account.
    Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
    While logged in as Guest, you won’t have access to any of your documents or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this behavior; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
    Test while logged in as Guest. Same problem?
    After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
    *Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
    Step 2
    The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
    Please take this step regardless of the results of Step 1.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
    Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem?
    After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of Steps 1 and 2.

  • I have message in screen ,Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled.

    i fix my iphone 5 to syn with my macbook in begging is ok after  i have message in screen ,Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled

    Unplug whatever other devices you also have plugged into USB, and try again. Better not to plug the iPhone into a USB hub.

  • How to add new fields in message creation screen

    Hi All,
        My requirement is to add another 2 fields in the message creation screen.
        Also I found this link is bit useful.
    Add custom fields to Support Message
    Can anyone share the detailed procedure to add a field in the message screen.
    Thanks in Advance.
    Regards
    Narasingam. B

    Hello,
    I think of something like:
    First, you create extension, with transaction WE30.
    Then, reduce your idoc, your extension should also be proposed.
    Do not forget to add this extension in outbound we82, and/or we57 in inbound, and WE20, and find BTE or exit to populate extension.
    regards.
    F.S.

Maybe you are looking for