Reading a Mac Disc on a PC

The optical drive in my mac went out so I thought I would just create a disc image (of the iLife '09 installer disc) on a PC and transfer it over with a thumb drive. But I can't get the PC to read the disc at all!
Any ideas on a workaround for this?

Hi,
Windows can't see or use a an OSX formatted CD/DVD unless it is specifically made to be seeable on a Windows PC.
HFSExplorer http://hem.bredband.net/catacombae/hfsx.html enables Windows to read HFS+ (Mac OS Extended) formatted disks.
For read and write access only MAcDrive http://www.mediafour.com/products/macdrive/ is avaiable.
Regards
Stefan

Similar Messages

Will not read Office:Mac disc

After reading that the new Intel-based Macs will run MS Office for Mac, I tried to install it onto my new MacBook Pro. However, the disc drive will not even recognize the disc. The drive will make strange struggling noises before spitting the disc back out.
I have used the disc 2x before on PowerPC-based Macs... there is one product key still available and I'm positive that there is nothing wrong with the disc.
Any suggestions?

Applechique --
Welcome to Apple Discussions !!
One thing to check first . . .
Did you uninstall (not just trash) your MS Office Test Drive?
I believe the Demo?Test Drive came installed on your new MacBook.
I think there is an uninstaller in the Office folder.

OS 10.5 - Boot Camp - Windows won't read Mac Disc for Driver Install

Hello everyone.
I have been through half a dozen headaches and a dozen hours of time wasted on this problem. I've tried multiple windows discs untill finally I bought a brand new version of Windows XP Pro. I've followed all of the instructions in my printed boot camp manual and I continously run into one problem:
Once windows is installed completely and I am at the windows desktop and need to eject the windows disc and insert the leopard disc to install drivers, I do so and windows does not recognize the mac disc whatsoever. It says the drive is empty, it is 0kb of 0kb, I cannot explore the drive, I cannot do anything. If I open it it is blank. I cannot access the internet in any way on windows because there are no corresponding drivers.. so I am at a loss.
Can anyone please help me? What do I do? I really apologize if this question has been answered, but I could really use some help.

Hi Sotaris,
It's a little vague what you mean by the "leopard disk". Do you mean the disk of drivers Boot Camp burns, or the actual Leopard installation DVD?
What you're supposed to do is launch Boot Camp while booted to the Mac OS. One of the first things it does is create a CD of Windows drivers that XP will need for your Mac. So you must have a CD-R or CD-RW on hand.
After that, Windows XP is installed. When that's done, there will be a number of hardware components that XP naturally doesn't recognize. That's when you insert the driver disk Boot Camp creates. I may have listed the order of things a little bit off here, but the main point is it sounds like you're skipping, or missing the part to create the Windows driver disk and trying to put the Leopard DVD in the drive.

Reading DVD Recorder Discs

Greetings,
My iBook G3 is a great little workhorse and I am hoping I can get more mileage out of it. Hopefully, this forum can set me straight!
I want to be able to play discs burned from a DVD recorder hooked up to my television on this iBook. The recorder we have is a cheapie TruTech DVD+RW. Much to my dismay however, the laptop isn't recognizing the burnt discs. It just spits them out. (My 17 inch Powerbook is doing the same, btw). The DVD players in my home read the burnt discs as well as a low end Compac laptop. Argh!
My questions are these:
Can the current DVD-ROM drive in my iBook (MATSHITADVD-ROM SR-8176) read burnt DVD+R discs or not?
Would the currently installed drive be able to read burnt DVD-R discs?
Do I need to purchase an external DVD drive for my iBook in order to read burnt discs? I'm hoping to avoid an external device if possible.
Would a new DVD-R recorder burn discs that are readable by the current drive? Would this be the cheaper route than buying an external DVD drive?
So many questions. I am thankful there are smart, helpful people out there that can set me straight.
Thanks in Advance,
Ruben
iBook G3 Dual USB Mac OS X (10.4.5) MATSHITADVD-ROM SR-8176

Hi Ruben,
All DVD-R's rely on some sort of recording "dye" , even if the colour isn't apparent to you. Different ones, use different types of dyes. They also have different forms of reflective coatings. Some work better in some drives than in others.
Memorex discs can actually come out of a variety of different factories. Some of these seem to be amongst the most problematic of all in Macs.
Head to http://www.videohelp.com/dvdmedia , type Memorex into the search field and hit return. You will see that while some Memorex discs fair quite well, others have pretty mediocre performance.
I think you should try a different brand of disc before assuming there is anything aactually wrong with your computer. There may be, of course, but disc incompatibility is so common that it is worth eliminating first.
For my part I've always found that TDK and Verbatim disks work well in all of my optical drives.
Cheers
Rod

HT3275 Time capsule message reads: The backup disc image "/Volumes/(my name)'s Time capsule/(My name)'s macbook pro sparsebundle" is already in use.

My time machine won't back up....The message reads : The backup disc image"/volumes/(my name)'s time capsule/(my name)'s macbook pro. sparsebundle" is already in use........I'm not using anything else that I know of.....?.......Help!

ATXMacMan wrote:
I use OS X server for maintaing Time Machine backups for several macs
Ah, that's a new wrinkle to me. I haven't tested the Server product, but there are a number of differences. As far as I can tell, the firmware update solved this for most, but not all, users of standard OSX.
Are you still on Snow Leopard server? It's quite different from later versions, I understand.
Have you tried selecting the base station, then Base Station > Restart via Aiport Utility's menubar? That still disconnects everyone, but might work by itself.
Otherwise, sorry, but I'm out of my comfort zone.
Hopefully one of the networking gurus will have an idea or two.

Having trouble with disc space on my 120G mac air. I back up to a separate my passport for mac disc, but my mac is also holding 40G worth of back up when i check what is using space. Why is this?

Having trouble with disc space on my 120G mac air. I back up to a separate " my passport for mac" disc , but my mac is also holding approx 40G of back ups as well when ive checked what is using space. Why is this?
Ive started running iphoto from the separate passport to save space,
and put all my music into the itunes match to save space as well
but it is still saying it is almost full because of the back ups!
I should of bought a bigger mac, but i need to make do at the moment, but it is hard when it constantly has only 10G or less space left.

When you use TimeMachine to back up a Mac notebook the local backups feature is automatically enabled. The local backup is just like a TimeMachine backup but it is done to the internal drive rather than an external. The important thing about local backups is that the feature is smart - as you need more drive space for your own data and applications, TimeMachine automatically culls the local backup to give you that needed space. So yes, it will look like you have very little drive space left and that the backup is 'robbing' you of needed GBs. But it really isn't.

DVD not being read by Mac..

I put in a DVD that had pictures on it in my imac..my mac didnt read the dvd. It doesnt come up in my finder window, iphoto or desktop. My preferences are set for pictures to arrive into iphoto. My mac will not eject the disc either. So, re-started mac, disc popped out. I put in another DVD and it worked fine. DVD showed on desktop and was able to eject without re-starting. Put my original DVD into another mac and it worked just fine..Was able to see all pictures..went into iphoto and was able to eject normally. Any idea why my iMac is unable to read this DVD?
Thxs in advance for the help

Thxs Rod..Though the disc is read on my mbp but not on my imac. I also made a copy of the pictures from my mb and tried to run it in my imac and it would not read.I put it back into my mb and it read it fine. My imac can play every other disc i put into it? Why just these pictures? I can get them on my mb but not on my imac

How to delete recent file history in adobe reader in Mac PC ?

How to delete recent file history in Adobe Reader in Mac PC ?
In Adobe Reader - Edit - Preferences - select Documents in the left panel and change the "Documents in recently used list" to 0. Yes ! the file history is gone But when you set back the value, you will see the file history again. This is not the way to do...
I have checked all the preference or setting. I couldn't found any clear recent file history in adobe reader.
Please help ! Thanks !

First off, you CANNOT set recent documents to zero. The absolute minimum it will accept is 1. And on my MacMini, (I just checked it to be 100% sure) I opened seven documents with Recent Docs set to 10 - they were ALL listed. I set it to 1 and all but the most recent cleared. I then closed Reader and reopened it. The list was 1 item. I reset Recent Docs to 10 and there was still only 1 item in the list.

LightScribe DVD±R/RW is no longer able to read all lightscribe discs(Blank/used)

Hi,
The product Name of my computer is: HP Pavilion dv6-6093ex Entertainment
Notebook PC support
The number of my computer is : LM610EA#A2N.
Could anyone please at this splendid forum take some of their precious time
out to really reply my questions and solve my problems?
FIRST OF ALL:
My HP Pavilion Laptop is about 3 years old.
My
sister's Dell Inspiron laptop is 3 years old.
My HP laptop is well-cared, as opposed to my sister's Inspiron Dell laptop, which is always thrown in dust without caring at all. Also, its battery is always inserted even when it is fully charged while the laptop is plugged in to the main power supply. However, my laptop is either used on only battery, or on plugin. Also, it is kept from the dust. But, I really found that the battery of the Dell laptop still lasts about three and half hours, and there is no problem cooling fan is not properly properly.
I only remember one thing differently done on my laptop battery which is I charged it fully, then I stored it without using it for about four months, then when I reused it, I found it got worse over time. I.e. first time of using it after storing,I found it empty, then I charged it again fully, however, then it lasted about 2 hours, then 1 and half hours, next an hour, now it is only lasting about 20 minutes without performance. If there is high performance, then
the computer shuts down suddenly.
My problem is follows:::
First: Whenever I inserted any Containing Data OR Data CD/DVD-RLightScribe discs, I found that HP optical driver was unable to read them. When clicking on the optical disc drive 'double-click' while disc was inserted, then I found that disc opened as this way(NOTE: With a CD/DVD player is grayed out)
I was told 'I suspect the culprit might be hardware and lightscribe dive might be
corrupt. Please sent it to service center to check. In addition, this thread could be as a reference:
http://answers.microsoft.com/en-us/windows/forum/windows_vista-hardware/media-in-cddvd-drive-is-not-...'
Since no one replied to me at HP forums, although my HP laptop is one of their products, I had to post my problem here to know if my driver is corrupted and needs to be replaced or not.
Blank Or Used(containg data) CD/ DVD ±R/RW lightscirbe is unable to be read by optical drive
When clicking on drive 'duble-click', I found it opens like a USB FlashDrive or With a CD,DVD player, however, : Bare in mind that 'with CD/DVD Player' is grayed out)
Not Blank(containing data) CD/ DVD ±R/RW NON -Lightscirbe disc opens normal:
Blank CD/ DVD ±R/RW NON-lightscirbe opens normal(Opens like
a USB FlashDrive or With a CD,DVD)::
My LightScribe System Software version is:
I've tried installed the latest version of lightscribe software, then I run
the diagnostic utility, however, the problem still persists.
My HP CD/DVD DVDآ±R/RW specs are::
Optical Drives
hp CDDVDW TS-L633R
Media Type DVD Writer
Name hp
CDDVDW TS-L633R
Availability Running/Full Power
Capabilities Random
Access, Supports Writing, Supports Removable Media
Read capabilities CD-R,
CD-RW, CD-ROM, DVD-RAM, DVD-ROM, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-R DL, DVD-RW
DL, DVD+R DL
Write capabilities CD-R, CD-RW, DVD-RAM, DVD-R, DVD-RW, DVD+R,
DVD+RW, DVD-R DL, DVD+R DL
Config Manager Error Code Device is working
properly
Config Manager User Config FALSE
Drive E:
Media Loaded
FALSE
SCSI Bus 0
SCSI Logical Unit 0
SCSI Port 0
SCSI Target Id
1
Status OK
Trying to solve the problem,
I have done these steps in order::
I tried checking with dignostic ulitiy:
I have tried Advanced View , this is the file of output data of dignostic utlity
LightScribe System Software Settings:
SOFTWARE\LightScribe\MessageDir C:\Program Files (x86)\Common Files\LightScribe\
SOFTWARE\LightScribe\LSPrintDialog C:\Program Files (x86)\Common Files\LightScribe\LSPrintDialog.exe
SOFTWARE\LightScribe\LSPrintingDialog C:\Program Files (x86)\Common Files\LightScribe\LSPrintingDialog.exe
SOFTWARE\LightScribe\LsPrintLauncher C:\Program Files (x86)\Common Files\LightScribe\LSPrintLauncher.dll
SOFTWARE\LightScribe\ResourceDir C:\Program Files (x86)\Common Files\LightScribe\res
SOFTWARE\LightScribe\LSPrintAPI C:\Program Files (x86)\Common Files\LightScribe\LSPrintAPI.dll
SOFTWARE\LightScribe\Update\UpdateShellCommand http://www.lightscribe.com/go/downloads/windows
SOFTWARE\LightScribe\Update\PreviousVersion 1.18.20.1
SOFTWARE\LightScribe\Update\CurrentVersion 1.18.27.10
SOFTWARE\LightScribe\Update\TrailingVersion
SYSTEM\CurrentControlSet\Services\LightScribeService\Type 16
SYSTEM\CurrentControlSet\Services\LightScribeService\Start 2
SYSTEM\CurrentControlSet\Services\LightScribeService\ErrorControl 0
SYSTEM\CurrentControlSet\Services\LightScribeService\
SYSTEM\CurrentControlSet\Services\LightScribeService\DisplayName LightScribeService Direct Disc Labeling Service
SYSTEM\CurrentControlSet\Services\LightScribeService\ObjectName LocalSystem
SYSTEM\CurrentControlSet\Services\LightScribeService\Description Used by the LightScribe software components to support 3rd party disc labeling applications using the LightScribe COM Application Programming Interface (LSCAPI). This service needs to run for LightScribe direct disc labeling to work.
SYSTEM\CurrentControlSet\Services\Eventlog\Application\LightScribeService\
SYSTEM\CurrentControlSet\Services\Eventlog\Application\LightScribeService\
SYSTEM\CurrentControlSet\Services\Eventlog\Application\LightScribeService\TypesSupported 7
SYSTEM\CurrentControlSet\Services\Cdrom\Enum\0 IDE\CdRomhp_CDDVDW_TS-L633R______________________0300____\4&334f7860&0&0.1.0
SYSTEM\CurrentControlSet\Services\Cdrom\Enum\Count 2
SYSTEM\CurrentControlSet\Services\Cdrom\Enum\NextInstance 2
SYSTEM\CurrentControlSet\Services\Cdrom\Enum\1 SCSI\CdRom&Ven_ELBY&Prod_CLONEDRIVE&Rev_1.4\1&2afd7d61&0&000000
SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon\allocatecdroms 0
SYSTEM\CurrentControlSet\Services\CDRom\autorun 1
SOFTWARE\INTEL\Intel Application Accelerator Not detected
Drives and Media:
Drive 0 : hp CDDVDW TS-L633R 0300 219 (E, Media Imaging Parameter : 114
I tried running the below command line to fix potential disk issue 'Chkdsk/r /f'
I cleaned the drive, discs, and so on.
I have uninstalled the all third-party data recording software.
I have uninstalled the Cyber DVD suite, lightscribe system software which
came pre-installed with my HP pavilion Notebook.
I have recovered my system from the HP Factory Recovery discs.
I have tried opening all those LightScibe discs not opening on my HP optical
drive, on a Dell optical drive, and all of them were opened well, although Dell
optical drive did not have a lightscribe feature at all., nor third party disc
recording software
However, the problem is still with opening the discs LIGHT-SCRIBE
Thus, my questions are:
How to determine if the drive is corrupted and needs to be replaced with
another one.
I think there something needed to be done on the BIOS Of my HP laptop[[[A similar problems happened on my Desktop computer's optical drive which is as follows (ALL discs are opened as empty by Optical Drive of My Desktop Computer) ---while my optical drive of my desktop was connected to the primary slave IDE, and the HDD was connected to the primary master IDE, the optical drive and hard disk are functioning well. However, I remember that while burning an image with Nero essential V: 5, something went wrong, and then the Optical Drive of My Desktop Computer (HL-DT-ST DVD-RAM GH22NP20) became NOT recognised/Installed on BIOS, although it was still shown on the device manager as a recognised device. Also, it was listed on my computer, however, when entering a disc(blank or with data) into the drive, I found it was not recognised, and it opened empty(no files at it), although it contains data. Thus, I decided to boot to BIOS, and clicked on 'Autodetection for IDE', then I found that only HDD was still shown as installed on BIOS. However, the optical drive was not. Th I tried clicking on it on BIOS and then clicking on 'enter' to try to let the device be re-recognized. However, that made no difference. I had to take part my computer ,and then reconnected the optical drive onto the secondary slave IDE , and let HDD connected to the same primary master IDE. Then, I found that the problem solved and all discs were read normally. Aslo, optical drive became installed on BIOS
What is meant with with double Layer Support.
How much does it cost?

Sparkles1 wrote:
HI @cooperator
I understand that you are having an issue with your battery and the lightscribe drive. You would also like to know about DL(Dual Layer) support.
Here is a link to Troubleshooting the notebook battery to assist with the battery concern.
You asked what dual layer support is , here is a definition from webopedia for the explanation.
What is dual layer support
As you stated in your post your system supports reading
The DL refers to dual layer, it does not list a CD DL. What type of disk are you using?
From your post I noticed it does read the title of the disk but is unable to read the file.
Did you use any form of compression software when writing the files?
Would you try inserting a supported blank disk and writing to it. If you can do this and read the disk after your drive is functioning.
The only other way to check would be to remove and reinstall it into another computer to test if it works there.
Yes there is a bios update listed on the driver page for your notebook.
HP Pavilion dv6-6093ex Entertainment Notebook PC Drivers
Updating the bios does have a potential to cause damage, for this reason I suggest contacting HP support for assistance.
Updating the BIOS
Please call our technical support at 800 474 6836. If you live outside the US/Canada Region, please click the link below to get a support number for your region.
World Wide Phone Support
I hope this helps!
Thanks a lot,
I wish that Paul_Tikkanen could have participated in solving this issue since I know he has insight in such problems.
Could you please be a little bit patient with me and go through all my points below and answer me::
IF you had had a close look at my screen shots before, you would have seeing I have classified the disc haveing and not having the problem into three categories each of which has its screen shots under it.
Blank Or Used(containg data) CD/ DVD ±R/RW lightscirbe is unable to be read by optical drive
Not Blank(containing data) CD/ DVD ±R/RW NON -Lightscirbe disc opens normal
Blank CD/ DVD ±R/RW NON-lightscirbe opens normal(Opens like a USB FlashDrive or With a CD,DVD)::
First The kind of discs I have been used to using, and seeing in the market are only:
CD-R, C-RW, DVD-R, DVD+R, DVD-RW, DVD+RW.
However, I never ever used or saw 'CD-ROM, DVD-RAM, DVD-ROM CD-R DL, CD+R DL, DVD-R DL, DVD+R DL, CD-RW DL, CD+RW DL, DVD-RW DL, DVD+RW DL.
Thus, Could you please be a little more detailed about each of the above disc types?
Second: I don't know if I can see 'DVD+R DL' written on the cover of DVD like what I am accustomed to see 'DVD-R'?
Third: What difference is there between 'DVD-RW', and 'DVD-RW DL', and 'DVD-R' and 'DVD-R DL'?
Sparkles1 wrote:
HI @cooperator
From your post I noticed it does read the title of the disk but is unable to read the file.
Did you use any form of compression software when writing the files?
NOTE, those discs are for HP Factory Recovery Discs.I have created those Discs via HP Recovery Manager. After creating them, I have labelled them with lightscribe software. ALL LightScribe are not read well and are unknown. Thus, my answer for your question is No, I don't use compression software unless if the program 'HP Recovery Manager' used a compression built-in tool while creating those discs'
Moreover, I have even restored my laptop from the HP factory Recovery discs which means everything must have been OK
Sparkles1 wrote:
HI @cooperator
Would you try inserting a supported blank disk and writing to it. If you can do this and read the disk after your drive is functioning.
Have you seen my screen shots well?
The key of my problem as to unable to reading LightScribe is the answer of this question of mine: Why do I see 'RAW' or 'unknown' as a file system for disc inserted whenever I insert a ligthSribe disc into drive?
All Blank Or containing data CD/ DVD ±R/RW lightscirbe are unable to be read by optical drive. When clicking on drive 'duble-click', I found it opens like a USB FlashDrive or With a CD,DVD player, however, 'with CD/DVD Player' is grayed out) When I chose 'like a USB FlashDrive, I found there was no disc inserted, although it was.
If you mean other discs not LightScribe, then I would be saying YES. And they all worked well, except the lightscribe(Blank, or containing data) were not read well at all.(all are unknown).
Sparkles1 wrote:
HI @cooperator
The only other way to check would be to remove and reinstall it into another computer to test if it works there.
You mean I need to remove the optical drive and install on another laptop brand. If so, It would be compatible with any laptop brand?
NOTE: the reason around this problem is not lightscribe discs(I think) since any optical drive without having a lightscribe feature can read lightscribe discs. For instance the Dell laptop(Windows 7) could read all lightscribe disc or non lightscribe discs, even although it doesn't have any lightscribe feature, nor a disc recording software, except the Windows built-in default tools. Dell optical drive, although not having a lightscribe feature, read all discs no matter the disc type is. Thus, In my HP optical drive having a lightscribe feature, I have decided to get rid of (lightscribe feature by removing the lightscribe system software, and all Cyber DVD-Suite). However, the problem is still with reading lightscribe discs.
Sparkles1 wrote:
HI @cooperator
Yes there is a bios update listed on the driver page for your notebook.
HP Pavilion dv6-6093ex Entertainment Notebook PC Drivers
Updating the bios does have a potential to cause damage, for this reason I suggest contacting HP support for assistance.
Updating the BIOS
First:: I have updated my BIOS from F.05 into F.1B by using HP Notebook System BIOS Update (Intel Processors) (sp55068) F.1B hoping to get rid of this problem, but that made no difference at all.
NOTE
Other suggested that I insert an empty rewritable CD and try running the following command: format e: /fs:UDF
I did, but it didn't help.
Other suggested to download the latest version LightSribe system software, but I would be saying how to do that as long as HP would be phasing out HP LightScribe Direct Disc Labeling technology. HP will gradually transition products to comparable optical disc drives without LightScribe technology.
Second:: I've also been searching in HP forums, but always they said nonsense comments which I don't put up with. Take this one for example,
I'd be happy to do all I can to help with your lightscribe.Please note:Beginning May 2011 and throughout the year, HP will be phasing out HP LightScribe Direct Disc Labeling technology. HP will gradually transition products to comparable optical disc drives without LightScribe technology. While this transition may affect other HP products, this document is specific to HP notebooks.- Source
This might be helpful too; Creating disc labels with LightScribe
NOTE:Hewlett-Packard's LightScribe website is no longer active. LightScribe software and disc utilities
may be found on a number of public websites. Search the Internet for LightScribeto find these pages.
This blurb and much more information can be found in the following document; Creating Disc Labels with LightScribe
The compelet discussion is here.
Finally I would be saying that LightScribe website is no longer available(discontinued). As HP said. IF HP customer care couldn't help their customers, I think it would be better to completely discontinue selling HP products.

Adobe Reader 9/Mac OSX 10.5.4/Internal Error after installing

Just purchased a new iMac with OSX 10.5.4 installed. I have 2.4 GHz Intel Core 2 Duo with 4 GB 667 MHz DDR2 SDRAM. Acrobat Reader v8.x won't run, so downloaded and installed v9 from the official Adobe web site. When I attempt to launch Acrobat Reader 9 I get the message "An internal error has occurred." I cannot go any further or do anything else. I've downloaded Reader 9 several times but the same problem keeps happening. I also purchased a new MacBook and Reader 9 installs and runs on that machine without any problems. Anyone have any idea why this might be happening on my iMac? Without Acrobat Reader it can really be a drag trying to work with PDF's.

(Gary_Roger) wrote:
I was wrong on both counts. With the help of the local Apple store, I found a solution. First, I Moved to Trash all adobe related files/folders from /Users/*myaccount*/Library/Cache and /Users/*myaccount*/Library/Preferences. When I started "Adobe Reader 9", I at least got the license agreement but again it failed with an "internal error". I then moved the /Users/*myaccount*/Library/Application Support/Adobe folder to my desktop. I was then able to start "Adobe Reader 9" successfully.
I was having the "Internal Error" message on all my repeated installs of Reader in Mac OS 10.6 ("Snow Leopard") and this fixed it for me. The only thing I did different, was after the app finally launched without an error, I dragged all the non-Acrobat Reader folders inside of /Users/*myaccount*/Library/Application Support/Adobe back to the folder. I then re-launched Reader just to check and all was fine.
Thanks! This fixed my Adobe Reader on Snow Leopard problem.

PC FORMATTED iPod read by MAC & PC? MAC formatted iPod read only by MAC?

Is this how the formatting issue works? I'm looking to buy an iPod for a friend who (I think) has PC.....
Since I'm a mac person, I want to buy the gift, load some music on, and ship it off to the lucky recipient....but if they have a PC , will it be recongnized once it's plugged in?
Any info would be helpful.
Thanks.

PC FORMATTED iPod read by MAC & PC? MAC formatted iPod read only by MAC? Is this how the formatting issue works?
Yes, that is how it works.
Since I'm a mac person, I want to buy the gift, load some music on, and ship it off to the lucky recipient....but if they have a PC , will it be recongnized once it's plugged in?
Okay, unless you restore your iPod while you're on the Mac, I believe it will still be formatted for a PC.
(You will not need to restore the iPod for transferring music to it on a Mac unless you want to upgrade the iPod's firmware on a Mac computer, then it will have to be Mac-formatted).
You see, when you recieve an iPod, it is shipped to you as a Windows-formatted iPod, probably since the majority of the population has PCs, and also, PC-formatted iPods are compatible for music transfer for a Mac also.
Does that make sense?
EDIT: Zevoneer has already answered your question, so you can ignore all of my post if you wish.
-Kylene

Adobe Reader 9 Mac - cannot copy images

I upgraded to Reader 9, and another person in our office is using 8 with the same problem. We can no longer copy images out of a PDF - when we try to paste an image that appeared to be copied we only get a gray box. We've tried many ways including pasting directly into Word or Excel, choosing 'New from Clipboard' in Photoshop Elements, creating a blank Photoshop file and pasting, etc. This has works perfectly in Acrobat 5.0 and in Reader 7.0.5 (which I have gone back to using - I'm sure glad I waited before removing it from my system!).
Any thoughts?

(Gary_Roger) wrote:
I was wrong on both counts. With the help of the local Apple store, I found a solution. First, I Moved to Trash all adobe related files/folders from /Users/*myaccount*/Library/Cache and /Users/*myaccount*/Library/Preferences. When I started "Adobe Reader 9", I at least got the license agreement but again it failed with an "internal error". I then moved the /Users/*myaccount*/Library/Application Support/Adobe folder to my desktop. I was then able to start "Adobe Reader 9" successfully.
I was having the "Internal Error" message on all my repeated installs of Reader in Mac OS 10.6 ("Snow Leopard") and this fixed it for me. The only thing I did different, was after the app finally launched without an error, I dragged all the non-Acrobat Reader folders inside of /Users/*myaccount*/Library/Application Support/Adobe back to the folder. I then re-launched Reader just to check and all was fine.
Thanks! This fixed my Adobe Reader on Snow Leopard problem.

What is the best ebook reader for Macs?

Hi,
What is the best ebook library / reader for Macs?
I have a Kindle for the actual reading, but wanted some sort of nice display library to sort and browse my books.
Any help is appreciated.
Thanks!
david

i have searched there, but rather than try 20 out, i'd rather see what people like here.
the people on discussion boards generally have good taste.
and by best, i mean the best -- your favorite. obviously that encompasses a range of qualities to embody "the best."

Acrobat Reader for Mac

I have a cd's that require the latest Adobe and Acrobat Reader for Mac to open. I tried without and it doesn't work. Can anyone help? I currently have a Mac version 10.6.8.

You can download Reader from here: http://get.adobe.com/reader/

Installing & running adobe reader on Mac

I installed Adobe reader on Mac OS X 10.7.5, using both Safari & Firefox, but it didn't work in either. Adobe is there, but won't run. I had Adobe before but then it disappeared. I downlaoded again in order to open pdf fillable forms. When I return to these pages, which I used in the past, it now says (in Safari) can't use this browser or run and relaunch (same browser I used before) or (in Firefox) I must agree to licensing agreement before use, which never pops up for me to agree to. Any suggestions?

Try the installer from http://get.adobe.com/reader/enterprise/

Reading a Mac Disc on a PC

Similar Messages

Maybe you are looking for