REAL time Monitor setup

Hi,
In solution Manager 4.0, RFC connections are setup alerady for early Watch, and works fine...
I would like to setup Real Time System monitor any one of R3 system forexample DEV system...
I setup CCMS alert for Entrie system MTE with memory alerts and it working fine + i am getting mails
However I am having a bit of difficulty setting up a few simple "Real Time Monitors" in solution manager
Point will be rewarded as solution per solution given
Thanks in Advanced
J

http://service.sap.com/monitoring (or use the direct link Monitoring your SAP NetWeaver Components [original link is broken])
Follow the setup guide for a CEN (Central Monitoring System). It's not different than setting up any CEN on a Netweaver installation.
Markus

Similar Messages

  • Where can i check in the real time monitoring tool if there are active calls in progress?

    where can i check in the real time monitoring tool if there are active calls in progress? 

    Hi
    Selecting Call Manager -->Call Process ---> call activity
    HTH
    Regards
    Carlo

  • Prime infrastructure 2.0 Real Time Monitor?

    Hi everyone,
    I install PI 2.0 and I want to know how can i configure and use the Real Time Monitor option?
    thanks

    Hello Dawit,
    Please check the following link, might be helpful,
    http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/2.0/configuration/guide/mon.html

  • LMS 2.1 and nGenius Real-Time Monitor 1.4

    Dear NetPros,
    Is the LMS 2.1 and the nGenius Real-Time Monitor 1.4 can be installed on the same system?
    Regards,
    Steve

    Yes, but not recommended. Keeping them on separate servers will be more beneficial.

  • Real Time Monitor Tool - Charting

    Afternoon all,
    I am using RTMT 8.1 to monitor Call Activity on a specific H323 gateway within our voice network. I've produced the chart which is correctly showing me real time information over a period of a couple of minutes. However, I want to display the chart over a period of 24 hours.
    Do I need to change the polling rate to 30 or 60 minutes and allow the chart to run for 24 hours before presenting it? Is there any way of producing historical data on RTMT? Any help would be apprecaited.
    Regards, Jamie

    Hi Jamie,
    Indeed in RTMT itself you should be able to achieve it by setting in counter properties "No. of data points shown on chart" to 50.
    Next form Edit > Polling Rate. Set it to 30 minutes. Now it shown over 24 hours but with sample rate of 2/hour it may not really be useful.
    So it would be better to have a higher sample rate and use the "Start counter logging" option to log the results to a locale csv file. So you can review the data afterwards with permformance log viewer or with Windows permance (perfmon.msc) from that locale csv file. Though you would need to leave RTMT running to log this information.

  • Cisco Unified Real-Time Monitoring Tool Administration Guide

    Hello Pros,
    I am in process of upgrading CUCM from 8.6 to 9.1.2 and receiving "not enough disk space on the partition" error.
    The show status from CLI shows 13499216K free space but I don't understand why we are getting the error message. I tried FTP and SFTP, from GUI and CLI with no luck.  Do I need to start deleting files (traces, firmwares, etc..)? Even if I do so it wil free up the space in active partition and change nothing in my inactive partition as all thoses files are in my active partition.  Your help is very much appreciated.
    Memory Total:        4016964K
            Free:         161516K
            Used:        3855448K
          Cached:        1745416K
          Shared:              0K
         Buffers:           9216K
                            Total            Free            Used
    Disk/active         14410496K        2301468K       11960264K (84%)
    Disk/inactive       14410560K       13499216K         167512K (2%)
    Disk/logging        50179664K       18651876K       28937612K (61%)
    MK

    Hi MK,
    If the percentage of disk usage is above the high water mark that you configured, the system sends an alarm message to syslog, generates a corresponding alert in RTMT Alert Central, and automatically purges log files until the value reaches the low water mark. So, try lowering the high water mark value as well and then restart the Log Partition Monitoring service.
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/service/6_1_1/rtmt/611-rtmt-admin/rtalert.html#wp1270174
    HTH
    Manish

  • Cisco CUCM session trace log viewer (in real-time monitor) doesn't show all calls

    hi all,
    could you please help with one trouble on CUCM 9.1: I activated CDR and set debug trace level as detailed and want to find history of my calls. I'm going to Tools -> CDR Analisys and Reporting and on the new appeared page i choose CDR -> Search by Phone Number. I make test call to my phone, try to search by my number phone but i doesn's see any incoming calls. It's worth noting that some outgoing calls i see. Could you explain why it is?

    Did you set the service parameter to log calls into CDR?
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/service/8_0_2/car/CAR/caranrpt.html#wp1037699

  • Real time data monitoring using multiple thermocouples via indicators and waveform

    I apologize in advanced for this question is probably somewhat simple but I am brand new to labview as well as to the forum and could use some pointers. I have a CompaqDAQ with two 9213 16 channel modules and I am trying to read in 30 thermocouples into a waveform as well as display 30 indicators so I can label each indicator with the corresponding thermocouple for real time monitoring. Each thermocouple corresponds to a specific location and it is critical that the interface have an accurate indication or label for each one. I am wondering if there is an easy way to do this besides splitting the signal and having 30 thermometers on my block diagram? Perhaps an array of some sort? If I use an array to create the 30 thermometers, does the DAQ assistant automatically sort the thermocouples in increasing numerical order. For example, would the first and second indicators on my interface automatically be assigned to the a0 and a1 channels of the first module or would I have to do this manually? Same for the waveform?  Thanks a lot!
    PS - Not sure if this message needed more specifics but just let me know if more info is needed and I will provide!
    Solved!
    Go to Solution.

    I see you are using the DAQ Assistant to create your task.  Now I understand why you are asking about labeling.  That is the NI Salesman's easy start up spiel...  But anyway, have you ever created a task in MAX instead of using the DAQ Assistant?  The interface is similar, and there may be a step or two more, but your end application will be more efficient and you will have more options with your data and properties.  For instance, I tried to update the physical channel names in the DAQ Assistant setup ,which it does let you do, but it doesn't propagate that change forward to the waveform chart legend.  Also, I don't know of any property node for that dynamic data type, although I never use it either.  I suggest setting up your task and channels in MAX, if you don't mind giving it a go.
    I wrote another example since I figured I didn't really lead you to the end with helping you out.  It uses a cluster, although a little barbaric.  I thought there was a more eloquent way of doing it by changing the labels, but I could not get it working as I anticipated.
    Attachments:
    TC Cluster Array Option.vi ‏28 KB

  • How to make real-time report per subscriber ( SCE2020)

    From the link below Cisco SCA BB SNMP Real Time Monitoring User Guide, 3.1
    http://www.cisco.com/en/US/products/ps6135/products_user_guide_chapter09186a008084ddc8.html
    it only make report on the global bandwitdh does anyone have i 3rd party software or good document on how to do snmp real-time report per subscriber?
    Thanks in Advance.

    SCE platform supports a limited set of variables that may be configured via SNMP (read-write variables). Setting a variable via SNMP (as via the CLI) takes effect immediately and affects only the running-configuration. To make this configuration stored for next reboots (startup-configuration) the user must specify it explicitly via CLI or via SNMP using the Cisco enterprise MIB objects.
    For the further details for the SCE follow the below url which will help you:
    http://www.cisco.com/en/US/products/ps6134/prod_configuration_guide09186a008078b43a.html

  • Real Time datasources

    Few questions regarding REAL TIME datasources -
    1)How can we identify what datasources are REAL TIME datasources in R/3?
    2)Can any standard datasources be converted to REAL TIME datasources.
    If yes ,what are the steps in details?
    3)Why only ODS is used to load for REAL TIME datasources and not INFOCUBES.
    4)Can generic datasources be built as REAL TIME datasources.

    Hi,
    please see my answers underneath the respective question.
    1)How can we identify what datasources are REAL TIME datasources in R/3?
    ==> field REALTIME in table ROOSOURCE
    2)Can any standard datasources be converted to REAL TIME datasources.
    If yes ,what are the steps in details?
    ==> Yes, if the extractor can provide Real-Time data, i.e. at every point in time delta information. A negative example are FI-GL extractors which are only capable to provide data on a daily basis.
    If you identify such a DataSource and the DataSource is critical to your project success, please contact me directly via EMail.
    Proceeding is as follows (SPS8 is recommended):
    a.) Set field ROOSOURCE-REALTIME for respective DataSource (per customer ABAP report)
    b.) Replicate DataSource
    c.) Create DeltaInit InfoPackage and execute
    d.) Create Transformation and DTP to a DataStore Object (if applicable)
    e.) Create a daemon in Real-Time Monitor (Transaction RSRDA)
    f.) Locate your DataSource in the 'Not assigned' part of the tree structure
    g.) Assign InfoPackage and DTP to daeomon (via context menu on the DataSource)
    h.) Start the daemon
    3)Why only ODS is used to load for REAL TIME datasources and not INFOCUBES.
    ==> Since data is immediately available for reporting and we have an open request we have a specific update processing for the data target (with a special DTP). This has currently only been implemented for DataStore Object.
    4)Can generic datasources be built as REAL TIME datasources.
    Yes
      Cheers
        SAP NetWeaver BI Organisation

  • Help needed in getting real time system performance monitor

    Hi,
    I need a real time system performance monitor for my solaris.
    i am able to graph system usage graph on a daily/weely basis using the ksar grapher.
    In the same way i need to capture the system utilisation real time to be viewed on a webpage. Please let me know if there are any free tool/scripts capable of doing it.

    Hi,
    Process Chain Errors
    /people/mona.kapur/blog/2008/01/14/process-chain-errors
    Common Process chain errors
    For Data Load Errors check this blog:
    /people/siegfried.szameitat/blog/2005/07/28/data-load-errors--basic-checks
    Implementation issues
    Lifecycle Implementation
    http://help.sap.com/bp_biv170/documentation/SolutionScope_EN.doc
    http://help.sap.com/bp_biv235/BI_EN/documentation/BWProjectPlan_EN.mpp
    Hope this helps.
    Thanks,
    JituK

  • Getting video to play real time in an NTSC monitor question?

    I’m trying to get video in my NTSC preview monitor to play real time. It will send a picture to the preview monitor but will not play real time even when timeline is rendered. I’m coming out of the back of my video card (ATI Radeon 9600) through a DVI cable to my HDTV monitor. Do I need a Firewire digital to analog converter box in order to see video in real time? I don’t want to use my camera as a pass through. Does FCE support a second monitor at all during editing?
    Any info greatly appreciated!

    Thank you so much for the reply! I just purchased a Firewire Datavideo DAC-6 DV to Analog Video Converter and it even has component out to the NTSC monitor. It will be here on Wednesday! Good to know I can run a preview monitor while editing. Thanks again for assisting me.

  • Reference monitor doesn't play simultaneously in real time? How is it used?

    I thought the point is to have two monitors playing back simultaneously for scopes / composite or to send to a secondary feed for clients, similar to video village on set.

    Not sure why you started a new thread on this ..but anyway.
    The reference monitor is not designed or suitable for a secondary feed to external monitors.
    It is used to have two looks at same frame eg a composite and a scope
    or two looks at  different frames eg unganged .  This maybe for a CC and grading comparison.
    It is not absolutely vital that it plays in real time for either of these instances.

  • Need to monitor any file change in the system, in real time

    Hi,
    I am running a program that I suspect may be doing changes in the filesystem, but I do not know which ones. I would like to know if there is a daemon/program that could help me monitor those changes. I tried AIDE, however, it works by creating a database of checksums for each file and does not report in real time potential changes. I would rather use a program that logs changes and timestamp them. Furthermore, AIDE is not useable with /var files, since there are many of them and they change so often. Is there another good solution?
    Alternatively I would like to run the program with monitoring. For instance, run the process as:
    monitor_program my_program_to_monitor logfile
    This would dump in logfile what my_program_to_monitor does to the filesystem.
    Thanks in advance.
    Last edited by zebulon (2011-08-24 15:44:10)

    no, at least with inotifywait, it is not possible. once you know what file is being changed you can use "lsof" to see what process have opened that file.
    i tried the following to search lsof output first thing when inotifywait finds a file change.
    file=$(inotifywait -r /home/mang/watch --format %w | sed 's/.$//'); lsof | grep $file
    while in another terminal running "vi /home/mang/watch/test"
    the output is:
    zsh 12574 mang cwd DIR 254,11 4096 4723089 /home/mang/watch
    vi 16790 mang cwd DIR 254,11 4096 4723089 /home/mang/watch
    try it!

  • SQL Developer Stability - Real Time SQL Monitoring

    I always get excited when a new release of SQL Developer comes out with all kinds of new features then I am quickly disappointed by the instability.
    The 2.1 Real Time SQL Monitoring is a great example. It has such great promise but it is not stable, the refresh doesn't work, if you scroll it wipes out the display so I have to exit and re-enter. Is anyone having more success with this tool than me? Are there Java Settings I need to consider? I already learned that if running the query in question from SQL Developer it has to be in an unshared workspace or SQL Monitor won't come up.
    Prior to going to native OCI connectivity my Connections Schema Tree was also very flaky, I work with huge delivered PeopleSoft HR Schemas most of the time.

    The file associations thing means you don't have access to the registry to associate file types. Probably connected to the Vista security model. Try registering the filetypes for use by sqldeveloper through explorer.
    This other problems generally means you don't have write access to the sqldeveloper system directory.

Maybe you are looking for