Really Worried Need Assistance
Hi Guys
I have installed Windows 8 x64 on my Lenovo Laptop with UEFI mode, how ever as of now every thing seems to be working fine.....but the thing is whenever my laptop starts to boot.....I mean at the UEFI boot loader screen it says Scanning & Repairing drive (\\?\Volume {bla bla bla bla bla}) :100% Complete and after that it boots to the metro UI.
Please refer to the screenshot which I have taken
Link to image
I doubt is there any bad sectors in my HDD or the installation went wrong...if it would be issue with the installation then it wont boot properly ... but its working fine...very strange but am unable to figure out what exactly the issue is
Moderator note: images totalling more than 50k converted to links per forum rules: Lenovo Community Participation Rules
Hi Abinash,
Welcome back to Lenovo Community Forums!
I’m sorry to hear that the computer displaying error message before booting to Windows, this seems to be the issue with the bad sectors in the HDD (Hard Disk Drive). Below is the link to download Lenovo Solution Center for the computer and scan the Hard drive if there are errors detected, however I would Strongly Suggest Calling Technical Support for Assistance, Click here to open a link where you can select the country and get the exact contact support number, I’m sure they will be a great help.
Lenovo Solution Center for Windows 8 (64-bit)
Hope this helps!!!
Do post us back for further queries.
Best Regards
Shiva Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!
Similar Messages
-
I'm uploading a photobook I made to be published. I need assistance in getting it to apple. The book is assembled and gets to the end of uploading when I get an error message, an error occurred while uploading. I have been trying all night. Help!
Welcome to the Apple Community.
I have seen previous versions mentioned in a pop up message before on iCloud.com, but I'm not really sure at all how it would help, as I couldn't get it to do anything.
The best advice I have at this time is to back up your work on your iOS device by regularly saving it to iTunes, if anything goes wrong you can then either load it into the numbers app again on the device or recover it via iTunes on your computer.
My syncs are immediate, I never get chance to see if it works in the background, sorry. -
Hi, i hav an Iphone 4S (ios 7.1) with me.. it is abnormally increasing its temperature due to no reason and i am really worried about that. The fully charged phone is getting empty within minutes. Not able to attend the calls due to its overheating. help me please..
It shows a 'temperature rise, need to cool down your phone' message regularly.. It happens when i when i try to connect my fone to the internet using cellular data, and it happens more suddenly when my 3g is on.. help me to sort out this, pleaseMake an appointment with the Apple genius bar for an evaluation.
-
Blackjack - using swing (Need Assistance)
Sir and Madam,
I just started learning Java with Java 5.0 Eclipse. I am taking a course for Java Programming. I am wondering if anyone is willing to help me to identify the missing sources or errors so that way I can learn more and more and have my codes runnable. I do not want to post my codes here because it is six pages in length.
If you are willing to help me, you can contact me at [email protected] with a subject "Java Assistance" so that way I can send the zip file to you unless you do not mind for me to post my code here.
My codes look pretty messy, I only learned since last March.
Really appreciate your assistance,
TTThanks for replying.. out of 6 pages of codes, I wrote most of them and they have no errors and test them with system.out.println. The output works very well until I added other class called Blackjack, the final class that contains all Swing and AWT containers/components. (I use Java 5.0)
The specific part of a whole 6 pages I need help is (check below):
(Note: class Card - create a single card contains both ImageIcon and value.
class Deck - create a whole deck with 52 cards contains two arrays of ImageIcon and values into Card[52], shuffle the cards etc..
class Player - create an array of class Card[10], calling for other card)
Now, the class Blackjack where it wont work.
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
class Blackjack extends JFrame implements ActionListener, Runnable
//Creating three buttons that operates the game
private JButton buttonHit = new JButton("Hit");
private JButton buttonStay = new JButton("Stay");
private JButton buttonReset = new JButton("New Game");
ImageIcon addIcon = null;
boolean loaded = false;
//Indexing the array's cells
int element = 0;
//Displays the result in message
String message;
int iwidth;
int iheight;
int cwidth = 1;
int pad = 1;
//Counting the games played
private int games = -1;
//Creating an object of class Deck
private Deck deck;
//Creating two objects of class Player (player vs dealer)
private Player player;
private Player dealer;
//Create a new game
void NewGame()
//Starts with Hit button to add the card
//so Button "Stay" is not available.
buttonHit.setEnabled(true);
buttonStay.setEnabled(false);
//Creating a new game included two players
player = new Player();
dealer = new Player();
//Then shuffle the cards with two players awaits
deck.shuffleCards();
//adds the game that start to play
games++;
//activites this function once the Button "HIT" got pressed.
void hit()
//Now two choices to press "Hit" or "Stay"
buttonStay.setEnabled(true);
//Displays a new image card
player.addCard(deck.deal());
if(player.getTotalValue() > 21)
message = "You lost! (score:" + player.getTotalValue() + ")";
//Disactivites all buttons except "New Game"
buttonHit.setEnabled(false);
buttonStay.setEnabled(false);
return;
message = "Score:" + player.getTotalValue();
//activites this function once the Button "Stay" got pressed
void stay()
while(dealer.getTotalValue() < 17)
dealer.addCard(deck.deal());
if(dealer.getTotalValue() <= 21 && player.getTotalValue() < dealer.getTotalValue())
message = "You lost! (" + player.getTotalValue()+
" - "+dealer.getTotalValue()+")";
else if (player.getTotalValue() == dealer.getTotalValue())
message = "You draw! (" + player.getTotalValue()+
" - "+dealer.getTotalValue()+")";
else
message = "You win! (" + player.getTotalValue()+
" - "+dealer.getTotalValue()+")";
//disables buttons "Hit" or "Stay"
buttonHit.setEnabled(false);
buttonStay.setEnabled(false);
//for ActionListener and ActionEvent communication
public void actionPerformed(ActionEvent AEvt)
//Only when Button "New Game" got pressed
if(AEvt.getSource() == buttonReset)
NewGame();
//Only when Button "Hit" got pressed
else if(AEvt.getSource() == buttonHit)
hit();
//Only when Button "Stay" got pressed
else if(AEvt.getSource() == buttonStay)
stay();
invalidate();
Blackjack(String title)
super(title);
getContentPane().setLayout(new FlowLayout());
setSize(800,600);
SetupButt();
setVisible(true);
void SetupButt()
buttonHit.setToolTipText("Click here for other card.");
buttonStay.setToolTipText("Click here for no more card.");
buttonReset.setToolTipText("Click here to start a new game.");
buttonHit.addActionListener(this);
buttonStay.addActionListener(this);
buttonReset.addActionListener(this);
getContentPane().add(buttonHit);
getContentPane().add(buttonStay);
getContentPane().add(buttonReset);
public static void main(String[] args)
Blackjack Demo = new Blackjack("Blackjack Card Game");
Demo.init();
void init()
Thread CardLoader = new Thread(this);
CardLoader.start();
ImageIcon[] load_images = new ImageIcon[52];
public void run()
deck = new Deck(this,load_images);
buttonHit.setEnabled(false);
buttonStay.setEnabled(false);
iwidth = getSize().width;
iheight = getSize().height;
this.invalidate();
invalidate();
public void paintComponent(Graphics g)
if(pad == -1)
pad = (iwidth - (cwidth * 2) - 4)/4;
g.setColor(Color.GREEN);
g.fillRect(0, 0, iwidth, iheight);
g.setColor(Color.BLACK);
g.fillRect(1,1, iwidth-2, iheight-2);
g.setColor(Color.WHITE);
g.drawString("YOU: ", pad, 40);
g.drawString("DEALER:", (iwidth/2) + pad, 40);
g.drawString(message, 5, iheight-20);
if(games>0)
g.drawString(games + " game(s) played...", 5,
iheight - 8);
int nowCard;
for(int i = 0; i < player.getCardCount(); i++)
nowCard = player.getCards().GetValue();
(Error here) g.drawImage(new ImageIcon("images/" + nowCard + ".gif"), pad,
70 + (20*(i-1)), this);
for(int i = 0; i < dealer.getCardCount(); i++)
nowCard = dealer.getCards()[i].GetValue();
(Error here) g.drawImage(new ImageIcon("images/" + nowCard + ".gif"), pad,
70 + (20*(i-1)), this);
super.paintComponents(g);
Message was edited by:
Turyturbo
Message was edited by:
Turyturbo -
I really just need the simplest solution. I have cleaned out old folders on the OMBP, but there are folders I need for work.
I am not a technical person. I have gone online and read a gazillion "All Ya Gotta Do...." to the point where my head swims.
I backed up my older MBP onto WD Passport Studio via Time Machine.
I transferred all my files there and put them all onto the newer MBP.
I expected to see Mail but did not.
Someone said just use Migration Assistant, but I dont find that anywhere.
Please dont say iCloud because I dont even know what it is. Sorry, but I just dont use my Mac other than for work, meaning online access for research, and then typing reports of various kinds... and for emailing.
Can I just hook the firewire directly from OMBP to NMBP and copy them that way??
Sorry I am such a dolt, but I really just want easy step by step instructions, thank you.
Would the Genius Bar at my local store be able to help me???
Thank you,Okey Dokey!
I followed the steps for the Target Disk thing, and was able to transfer everything on my old desktop, in my old pictures file... all the final transfers regarding my documents and photos.
BUT
there were no folders for Mail, and when I went to the only folder I could find that said "Mail" -- which was under "applications" it then told me that I could not transfer old "mail" to new "mail" since they were different versions...
Now THIS makes sense,,, and I was not looking to do that...
but how do I find all my mail folders????
Is there someplace I should be saving them in order to get them???
Do you mind helping me with instructions on how to do this?
Thanks! -
I need assistance to install LabView MindStorm NXT module in a Desktop system with Win XP and a Laptop with Win7. Both are 32 bit with all service packs applied. I purchased the academic version from a company called On-The-Hub.
Attempted to install but seems to reject my serial number?Hi Rob,
Thats really strange because the NXT Module 2010 and the NXT Module 2011 are free and don't require serial numbers. Where did you obtain the installer? The core LabVIEW installer requires a serial number but if you already have that installed, the NXT Module is just a free addon. Here are the links to the module for LabVIEW 2010 & 2011
NXT Module 2011 : http://joule.ni.com/nidu/cds/view/p/id/2637/lang/en
NXT Module 2010: http://joule.ni.com/nidu/cds/view/p/id/2551/lang/en -
Hi...lags animations in games and messages and album pic..when disable assistive touch,it's true and fix..please release update to fix this in ios 7.1..i need assistive touch and fast game and animation booth!!
No Apple here, user to user forum.
I will not be releasing any version of iOS ever. -
I am trying to setup Microsoft office mail and need assistance - I am receiving the error, unable to find server and DNS setting in the Network
Which version of OSX and what email provider are you using.
-
I installed Mountain Lion in my IMac and now, some times, when I start up my mac it looks with a black screen and white text. I'm really worry about it, can somebody help me?
Don't worry, this is probably just Verbose Mode. It's perfectly harmless. If you're not specifically invoking it, than it's probably down to an unwanted setting in NVRAM. See this article on resetting NVRAM if it continues to bother you.
-
Need assistance with Windows 2008 R2 server BSOD - ATTEMPTED_EXECUTE_OF_NOEXECUTE_MEMORY (fc)
Need assistance with Windows 2008 R2 server BSOD - ATTEMPTED_EXECUTE_OF_NOEXECUTE_MEMORY (fc)
I have a Windows 2008 R2 server which is experiencing random BSOD during the night. This is occurring maybe once or twice a week. I have gathered two Memory crash files. This server is running Citrix XenApp 6.5 but nothing else is reporting an issue except
for the memory dump. I’m looking for assistance in reading crash file and finding the cause.
I’ve spent over a week going through articles trying to learn and trouble shoot the BSOD but no closer to understanding the WinDbg 6.3.9600 report.
This is a production server and I have verified that Windows Updates has updated the server with latest releases. I’m hoping that the crash file will show something before I have to run the Driver Verifier.
The crash zip file is located -
https://onedrive.live.com/redir?resid=9644A4E0A26873B1!2359&authkey=!AMS4Svuk-SS3-JA&ithint=file%2czip
* Bugcheck Analysis
ATTEMPTED_EXECUTE_OF_NOEXECUTE_MEMORY (fc)
An attempt was made to execute non-executable memory. The guilty driver
is on the stack trace (and is typically the current instruction pointer).
When possible, the guilty driver's name (Unicode string) is printed on
the bugcheck screen and saved in KiBugCheckDriver.
Arguments:
Arg1: fffff880009eff38, Virtual address for the attempted execute.
Arg2: 8000000002cfe963, PTE contents.
Arg3: fffff8800da2eea0, (reserved)
Arg4: 0000000000000002, (reserved)
Debugging Details:
DEFAULT_BUCKET_ID: WIN7_DRIVER_FAULT
BUGCHECK_STR: 0xFC
PROCESS_NAME: powershell.exe
CURRENT_IRQL: 0
ANALYSIS_VERSION: 6.3.9600.17237 (debuggers(dbg).140716-0327) amd64fre
TRAP_FRAME: fffff8800da2eea0 -- (.trap 0xfffff8800da2eea0)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=fffffa80070f3648 rbx=0000000000000000 rcx=fffffa80070f3648
rdx=fffff8800da2fbf8 rsi=0000000000000000 rdi=0000000000000000
rip=fffff80001680b80 rsp=fffff8800da2f030 rbp=fffff8800da2fbd0
r8=fffff8a01804c680 r9=fffff8800da2fc68 r10=fffffffffffffffd
r11=fffff8800da2fa90 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0 nv up di pl nz na pe nc
nt!KiPageFault:
fffff800`01680b80 55 push rbp
Resetting default scope
STACK_COMMAND: kb
FOLLOWUP_IP:
nt! ?? ::FNODOBFM::`string'+44dfc
fffff800`017008b8 cc int 3
SYMBOL_STACK_INDEX: 1
SYMBOL_NAME: nt! ?? ::FNODOBFM::`string'+44dfc
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: nt
IMAGE_NAME: ntkrnlmp.exe
DEBUG_FLR_IMAGE_TIMESTAMP: 531590fb
IMAGE_VERSION: 6.1.7601.18409
FAILURE_BUCKET_ID: X64_0xFC_nt!_??_::FNODOBFM::_string_+44dfc
BUCKET_ID: X64_0xFC_nt!_??_::FNODOBFM::_string_+44dfc
ANALYSIS_SOURCE: KM
FAILURE_ID_HASH_STRING: km:x64_0xfc_nt!_??_::fnodobfm::_string_+44dfc
FAILURE_ID_HASH: {aa632d36-b0f7-67cf-89e2-1cec389c0a11}
Followup: MachineOwnerHi Kaysel_GTG,
Just addition. Regarding to Bug Check 0xFC, please refer to following article and check if can help you.
Bug Check 0xFC: ATTEMPTED_EXECUTE_OF_NOEXECUTE_MEMORY
By the way, since it is not effective for us to debug the crash dump file here in the forum. If this issues is a state of emergency for you. Please contact Microsoft Customer
Service and Support (CSS) via telephone so that a dedicated Support Professional can assist with your request.
To obtain the phone numbers for specific technology request, please refer to the web site listed below:
http://support.microsoft.com/default.aspx?scid=fh;EN-US;OfferProPhone#faq607
if any update, please feel free to let us know.
Hope this helps.
Best regards,
Justin Gu -
Need assistance to update Photoshop cs6 and Lightroom to version 2014. Please help!
Need assistance to update Photoshop cs6 and Lightroom to version 2014.
I have a Mac. I am not a member in Creative Cloud, invested big and bought CS6 and LR in the beginning of last year.
Please help!These are not updates (just as CS6 was not an update to CS5), but upGRADES. They are available to CC (Creative Cloud) subscribers. While in the past you might have been able to pay for an upgrade (e.g. CS5 to CS6) you now have to subscribe. Once you are a subscriber you can upgrade to each new version as it comes along.
As well as the full CC subscription there is a $10/mo plan with only Photoshop and Lightroom. Creative Cloud Photography plan | Adobe Creative Cloud -
Need assistance posting Webhelp to Company Sharepoint site
Need assistance posting Webhelp to Company Sharepoint site.
Check out this Adobe blog post and see if it helps: http://blogs.adobe.com/techcomm/2012/10/integrating-robohelp-projects-with-sharepoint.html. It would also be a good idea to ensure you have the appropriate SharePoint permissions for RoboHelp to write to your document folder.
You may also want to look at this webinar; http://www.adobe.com/cfusion/event/index.cfm?event=set_registered&id=2099687&loc=en_us -
Tried to reinstall PS CS6 from download, will not load after download and install, need assistance
I tried to reinstall PS CS6 from download, will not load after download and install, need assistance.
Thank you.Thanks for the suggestion - but I eventually tried again and was able to contact via "chat" to someone qualified to help. The problem was that in my existing "bridge" - preference was (I think by default) - checked to startup in background on Login. I did not realize this - because I don't think I set it that way in the first place (maybe I did a few years ago) - and I could not see anything in task manager to suggest that bridge was running an application or any process - but when I learned this - I was successful in installing PS CS6.
Yes, I'm still not on solid ground re: whether or not I want to change from "owning" the tool or renting it -- what concerns me is that is sounds like regardless of users wishes, Adobe is headed in this direction and will eventually make it financially more feasible to go that route. At the moment I think they are "asking" for everyone to get on their bandwagon, but who knows. They have a powerful set of tools, that they continue to support and advance - and along with those development and support costs, they also would like to make a profit - so I understand if their past marketing model is no longer sufficient.
Thanks again.
John -
Compiling a driver, need assistance on kernel source configuration
Hello BBS.
I am compiling a module for the Asus PCE N53 wireless pci-e card. I have obtained the driver source, and followed the instructions, and have gotten to the point where I need assistance. The instructions requires the kernel source, i have successfully obtained and configured it using the Command line prompt, except for one feature. I need to enable the intel IPW2200 driver code in the kernel source for this driver. What procedure do I follow to enable it?> I know in face value, that my request may seem odd. I just need to use the source of the kernel, not a new kernel... I have found that what I am requesting... will fix the problem, based on a Gentoo solution: http://forums.gentoo.org/viewtopic-t-93 … art-0.html. Needing to know how to configure the kernel source to enable the intel driver still stands. The source I am using is the latest arch kernel source.
===============
RT5592 Linux Driver quick start
====================
Check tools:
====================
*Before install driver, please check already install compile tool and kernel source code
1>Install compile tool
$yum install gcc-c++
2>check kernel source code exists /usr/src/kernels/ "kernel name"
Download your kernel source code
*http://www.kernel.org/pub/linux/kernel/
or
$yum install kernel-devel
====================
Build Instructions:
====================
1> $tar -jxvf DPO_GPL_RT5592STA_LinuxSTA_vx.x.x.x.tar.bz2
go to "DPO_GPL_RT5592STA_LinuxSTA_vx.x.x.x" directory.
2> In Makefile
set the "MODE = STA" in Makefile and chose the TARGET to Linux by set "TARGET = LINUX"
define the linux kernel source include file path LINUX_SRC
modify to meet your need.
3> In os/linux/config.mk
define the GCC and LD of the target machine
define the compiler flags CFLAGS
modify to meet your need.
** Build for being controlled by NetworkManager or wpa_supplicant wext functions
Please set 'HAS_WPA_SUPPLICANT=y' and 'HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y'.
=> $wpa_supplicant -Dwext -ira0 -c wpa_supplicant.conf -d
** Build for being controlled by WpaSupplicant with Ralink Driver
Please set 'HAS_WPA_SUPPLICANT=y' and 'HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=n'.
=> $wpa_supplicant -Dralink -ira0 -c wpa_supplicant.conf -d
4> $make
# compile driver source code, need administrator.
# To fix "error: too few arguments to function ¡¥iwe_stream_add_event"
=> $patch -i os/linux/sta_ioctl.c.patch os/linux/sta_ioctl.c
5> $make install
#install driver
#copy RT2860STA.dat to /etc/Wireless/RT2860STA/RT2860STA.dat
6>$vi /etc/rc.d/rc.local
#input "ifconfig ra0 up"
$reboot
7> unload driver
$ifconfig ra0 down
$rmmod rt5592sta
======
Heres the output of my error, when I compile:
=======
make -C tools
make[1]: Entering directory `/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/tools'
gcc -g bin2h.c -o bin2h
make[1]: Leaving directory `/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/tools'
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/tools/bin2h
cp -f os/linux/Makefile.6 /home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/Makefile
make -C /home/white/linux-3.2.9 SUBDIRS=/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux modules
make[1]: Entering directory `/home/white/linux-3.2.9'
WARNING: Symbol version dump /home/white/linux-3.2.9/Module.symvers
is missing; modules will have no dependencies and modversions.
CC [M] /home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.o
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.c:2364:2: error: unknown field ‘private’ specified in initializer
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.c:2364:2: warning: initialization from incompatible pointer type [enabled by default]
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.c:2364:2: warning: (near initialization for ‘rt28xx_iw_handler_def.get_wireless_stats’) [enabled by default]
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.c:2365:2: error: unknown field ‘num_private’ specified in initializer
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.c:2365:2: warning: excess elements in struct initializer [enabled by default]
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.c:2365:2: warning: (near initialization for ‘rt28xx_iw_handler_def’) [enabled by default]
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.c:2366:2: error: unknown field ‘private_args’ specified in initializer
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.c:2366:26: warning: excess elements in struct initializer [enabled by default]
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.c:2366:26: warning: (near initialization for ‘rt28xx_iw_handler_def’) [enabled by default]
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.c:2367:2: error: unknown field ‘num_private_args’ specified in initializer
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.c:2367:2: warning: excess elements in struct initializer [enabled by default]
/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.c:2367:2: warning: (near initialization for ‘rt28xx_iw_handler_def’) [enabled by default]
make[2]: *** [/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/sta_ioctl.o] Error 1
make[1]: *** [_module_/home/white/driver/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux] Error 2
make[1]: Leaving directory `/home/white/linux-3.2.9'
make: *** [LINUX] Error 2
Last edited by confusedoldman (2012-12-25 20:14:34) -
I need assistance opening a zip file.
I need assistance opening a zip file. Please advise or assist.
Thanks,
TIGER FRANKHi TIGER FRANK
Please download winzip from below link and install it to open .zip files ...
http://www.winzip.com/downwz.htm
Maybe you are looking for
-
Hello, need help when i am deploying a dimension in ssas i m getting error
Error 3 OLE DB error: OLE DB or ODBC error: Login failed for user 'NT Service\MSOLAP$MEENA'.; 28000. 0 0 Error 4 Errors in the high-level relational engine. A connection could not be made to the data source with the DataSourceID of 'Adventure Works D
-
How can I prevent an automatic bookmark?
I downloaded the Xsticky addon for Firefox and after determining that it was not what I wanted, chose to delete it. However, it keeps adding itself as a bookmark every few days (or hours sometime!). I emailed the developer and got no help; in fact, h
-
In IPhoto, I cannot get the "Edit picture" to come up when I click on "options." Only "border" and "effects" comes up. How do I get "edit"?
-
PS4 Not Enough Free Memory Problem
My PS4 keeps telling me i don't have enough space even for the littlest of downloads even though i have 20gb+ free. It attempts to prepare the download and keeps jumping percentages (2%, 5%, 14%, 0%, 49%, 0%, 2% then says cannot download file) I don'
-
Megaworks HISSING real solution
I wanted to give you guys a possible (tested) solution for this problem because I guess I'm not alone with terrible hissing sound problem out there. It was driving me mad as well Mind you, I am using 3(?) year old Megaworks 50D speakers which worked