Reapplied the thermal paste, now the fans kick in too early - downgrade FW?

First of all, I have not forgotten to attach the temp sensor as previously mentioned. I was quite lucky that everything went well.
My MBP is now 60 C top at almost full load (doing video at 80% load) and runs 48 in idle.
Which is incredible but it's also loud. Even when idle the fans run faster than the minimal speed, which is obviously caused by better heat conductance. When under load the fans quickly begin to spin full speed. As I said I havn't topped the 60 C mark yet.
Partly I think this has to do with the SMC firmware update, as Apple tweaked the fans to spin up earlier.
What I'm looking for is a way to get the old threshold setting back (the one before the smc firmware update). So that my MBP is as cold as possible but also more quiet than now.
And I read that there is a way of editing some powermanagment settings in order to change the threshold but havn't been able to google it.

Maybe it's my english, but the fans don't go full speed all the time. Now as I barely started the MBP and just surfed the internet a bit, I have fans running at their minimum.
And they stay on minimum as long as I don't do any harder work. Let's say start playing iTunes with visualization on.
As for the skills. I'm not professionally trained, but I've been building my own PCs for a couple of years now. Never laptops, obviously, as they come already built. And yes I also have a copy of the Service Manual that was floating around. I think I tend to infrom myself very carefully before doing any such work. That's probably I'm a medical student, which brings us to thermodynamics.
Apple defenitely applied too much termal paste, which has the effect that instead of filling in only the microscopic spaces of air between the heatsink and CPU, the thermal paste actually forms a layer between the CPU and heatsink. And generally speaking the thermal grease is a worse conductor than the CPU/Heatsink junction, but still much better than small spaces of air that would be between the CPU and Heatsink if no thermal paste was applied.
Strangely my girlfriend has a MBP which doesn't get as hot as mine. But her was bought in august, mine in april, so Apple might have looked into the problem themself.
About the Apple support thing:
I'm from Slovenia, the official Apple seller ( www.epl.si ) has a very rude way of customer support. Luckily I live very near the Austrian border, so I bought my MBP in Austria.
Well it seems to me that controlling the fans isn't yet possible on the MBP, as noone was able to point into any direction.

Similar Messages

  • Did you guys change the thermal paste of the CPU/GPU?

    I saw lots of my friends change to IC DAIMOND thermal paste but in the end their GPU still go BOOM and burned.
    Is it worth it ? because i do not know how to apply it and i dont want to void my warranty as well

    I replaced my GE70 with IC Diamond.  Seems to be working great after 4 months.  Like Chiyawa mentions, you should be cleaning the fan, vents, and other dusty areas on a regular basis.  I clean mine at least every month if not every 2 weeks.  Just helps keep everything clean.  But using the Cooler Boost certainly helps.  I rarely run games without using that.  Not a single glitch.
    But in all fairness, I don't game all the time.  Maybe 10+ hours per week. I also added 2 mSata drives and replaced the HDD with a Samsung 830 256gb ssd.  I think this helps a lot with speed, weight, heat, and functionality of the laptop too.  Was a no brainer.  While I was in there to replace the drives, that's when I replaced the thermo with IC Diamond and also upgraded the Wifi to AC.  Tried the killer but the AC was a tad bit faster.

  • How can I successfully reapply the thermal paste in my MacBook Pro? (2008)

    I'm having issues with keeping my computer cool, mainly while playing games like SC2 that require a good amount of power. I've downloaded fan control apps, bought cooling pads (usb powered) and still no luck in cooling this thing down. I recently learned that Apple for some reason applies the thermal paste too thick, which can cause the computers to be a lot hotter than they should be.
    I'm not worried about voiding warranty, seeing as I don't even have a warranty. I've already opened it up to upgrade the ram and the hard drive so I know my way around inside there and have the stuff I need in order to do it properly.
    What I need to know is where I can get the thermal paste, what kind I need, how it needs to be applied and with what (as well as how to get the old paste off), the steps I need to take in order to get to where this paste is even at inside the computer...etc.
    If there's anyone who's already successfully pulled this off, lemme know how you did it and if it helped any. I've read there've been significant temp drops since reapplying it in a lot of these pros, so I'm just interested.

    Hi
    I’ve yet to remove the heatsinks of the CPU and GPU on my MBP. But I’ve replaced CPU and GPU heatsinks on my PC many times, so hopefully you’ll find my suggestions helpful.
    1st use the laptop for a bit to get both the CPU and GPU warmed up so it will be easier to remove the heatsinks.
    Remove the back cover and run your hands over the back side of the metal cover few time to get ride of any static charge that might be there (or any unprinted metal surface will do).
    Remove the screws and heatsink one at a time. You might find the thermal past dried up (happens when company used cheap past and after computer is used for few years). Use tissues to wipe the past off both cores and heasinks.
    You can also buy thermal past remover and clearer such as this:
    http://www.amazon.co.uk/Arctic-Silver-ArctiClean-Material-Purifier/dp/B000BKP306 /ref=pdbxgy_computers_textb
    I normally use Arctic Silver Thermal Paste, I found it's the best past around, and everybody I know are happy with it.
    There are two ways to apply the past. If your CPU is a Core2Duo, than you can just put a little bit on the center and press down with the heatsink. This is because the 2 cores on the CPU are located near the center of the processor so it does not matter if the edges are not covered with past.
    Or if you want to play safe, you can cover the enter CPU with an even thin lay of past using a flat plastic card.
    When it comes to thermal past, less is more, you only want little bit to cover up the metal cover on the processor. I say no more than 0.5 mm thick.
    Cover the entire GPU with past as well, I’m not sure if the RAMs on your graphic card are cooled by the heatsinks. If they are, you might need some thermal pads for them.
    You’ll find the whole process quite easy as long as you take your time. You can found lots of info on this with Google and Youtube.
    Good luck and don’t forget to give the heatsinks a clean with a can of compassed air before you put them back on.

  • Was there ever a resolution to the thermal paste issue? Worth reapplying?

    Last time I checked these forums was a month ago and people were debating whether there was any concrete benefit to popping open the MBP and reapplying thermal grease. For each guy that said it helped, another said it did nothing. Was there ever a consensus or official resolution to this debate?

    Save your money. Besides if you take the computer to an authorized Apple repair center they will not do the work unless you have an authorization from Apple Customer Service. They will not authorize the work unless there is something specifically malfunctioning. If you really want the thermal paste re-applied you will have to do it yourself. This requires a complete disassembly of the computer and some special drivers.
    If you read the article I referenced you will note that there is little point to replacing the paste.
    You can download and install an extension called Speedit.kext along with a companion program called CoreDuoTemp (www.versiontracker.com, www.macupdate.com, or www.increw.org) and use it to monitor the CPU's core temperature. Unless it's running hotter than "normal" there's really nothing to worry about. Normal temps typically range between 50-75 C under loads varying from 2-30 percent or more.

  • MBP and the Thermal Paste Discussions

    I've read with interest the postings on this web site regarding the MBP heat issues and the possibility that too much thermal paste is causing that problem. I've spent quite a few years designing computer motherboards using Intel processor chips, and want to share some thoughts on the topic. I only mention my background because one thing this business has taught me is that we can all be easily mislead by our test data if our process for gathering the data isn't rigorous (and, believe me, I've learned that lesson many times).
    First, the excess thermal paste is definitely a problem, regardless of whether it is the root cause of the heat issue. Some of the photos posted on the various web sites show thermal paste covering bypass capacitors on the chip carriers (the green fiberglass boards that carry the CPU and GPU die). Thermal pastes can cause stray capacitances that can interfere with circuit operation. Standard industry practice is to use only as much paste as is necessary to achieve a layer that is about as thin as a single layer of tissue paper (or less). The amount used by Apple is far too large, particularly because the paste in coming into contact with other electrical components and conductors. A common failure mode associated with degraded bypass capacitors is random (and unrepeatable) crashes due to corrupted digital data in the processor chip.
    In addition, all thermal pastes contain various types of fluids. Over time, these fluids evaporate, and frequently they condense elsewhere inside a computer. When CD drives were first introduced years ago, a common cause of mid-lifetime failures was condensates on the optics of the laser. The condensation fogs the lens and interferes with the ability of the laser to focus while reading and writing data. The contamination was traced to outgassing by thermal pastes, greases, sulfurized elastomers, and similar items used to build the computer. (Note that the Apple service manual for the MBP refers to the thermal paste as “thermal grease”.) Consumer electronics manufacturers learned to minimize the use of such materials in computer designs. The amount of thermal paste shown in the Apple service manual is very large, and I wouldn't rule out that it might contribute to future DVD drive failures.
    It is difficult to say, based on the available data, that reducing the amount of thermal paste actually contributes to improving the thermal behavior of the MBP. Part of the problem is that the procedure to remove the pastes involves disassembling the laptop, and this introduces the possibility that the disassembly/reassembly process is inadvertently fixing the problem.
    First, the high case temperatures could be the result of loose or poorly placed thermal sensors. If the disassembly/reassembly process fixed a loose sensor, or loose sensor electrical connection, or placed the sensor in a better position, you would get lower case temperatures, and possibly (inadvertently) attribute this to less paste.
    Second, the cooling system design in the MBP requires that the die caps on the chip carriers be pressed tightly against the pads on the heat sink, so that heat is transferred efficiently. If the MBP is not assembled properly, (i.e., if the logic board mounting screws are not properly torqued, or the logic board is not mechanically aligned properly to ensure a tight fit to the heat sink), it is possible that this will manifest itself as high case temperatures. In the Intel processor chips there are two paths for heat to travel – out of the die cap, and through the electrical contacts to the motherboard. If the die cap isn’t properly cooled, heat will instead go into the motherboard, and the case temperature will rise. There is a possibility that the disassembly/reassembly process will fix a loose or misaligned logic board problem, with the result that the case temp will be reduced.
    Also, if you work through the details of the thermal model that results from excess paste, it's hard to see how it would result in more heat to the case and less to the heat sink. Most of the photos on the web appear to show thin paste on top of the die, indicating that there was probably a low thermal resistance path to the heat sink prior to disassembly. The excess paste to the sides will simply further reduce the thermal resistance between the chip carrier and the heat sink. I may be missing something, but it's hard to envision how this lower thermal resistivity between the CPU and the heat sink drives more heat into the case. But it is also possible that the disassembly process destroys evidence of the actual connection to the heat sink, so this failure mode is hard to judge.
    The best way to determine if removing the excess paste is actually helping would be to measure the exhaust air temperature from the cooling fans before and after removing the excess paste. I haven't seen such data, but if it were taken, and showed that the exhaust air was at a significantly higher temperature after the fix than before it, then we would know that the fix worked. If not, then the heat is going elsewhere, and it is possible that fix has actually made things worse.
    Finally, all the symptoms we're seeing can be explained by poor software calibration and/or incorrect software control of the CPU clock speed. I wouldn't rule out a software fix at his point.
    I'm not saying removing the paste is not a fix, only that there are still open questions that remain to be answered. It would be hard for me to recommend that anyone rework an MBP for the thermal problem in the absence of additional data.
    For myself, I own an MBP, and though I have access to an electronics lab and some great technicians, I intend to buy Applecare, and in the meantime wait for a fix (or at least more information) from Apple.
    Best of luck to everyone who has this issue - thats what we get for being early adopters.
    G5 2.5 DP   Mac OS X (10.4)  
    G5 2.5 DP   Mac OS X (10.4)  
    G5 2.5 DP   Mac OS X (10.4)  
    G5 2.5 DP   Mac OS X (10.4)  
    G5 2.5 DP   Mac OS X (10.4)  
    G5 2.5 DP   Mac OS X (10.4)  

    Well I replaced my thermal compound and the temperature on my cpu went down and the temperature of my case went down also. The fans also kick in sooner leaving me to believe that the heat is being properly distributed the heatsink whereas before it was not as there was too much thermal compound making it act like an insulator.
    I cannot say if the exhaust air is any hotter, but I know overall my laptop is much more cooler and never gets extremely HOT. Even under heavy loads the areas where it used to get really hot, above f keys, palm area, underneath the MBP are not hot to the point where someone could burn themself at all.
    I really do hope that Apple does address this issue because I could not live with the heat before, I always had to hook up an external keyboard because my hands got too sweaty from the palm rest and the keyboard. Now everything is operating like any other laptop I've owned and I am a very satisifed Apple user. Let's hope that Apple is really looking into it and will have a reasonable answers for all MBP users in a reasonable amount of time.

  • Early 2011 MacBook Pro- The thermal paste discussion.

    It is my goal to clear up the questions and concerns Apple customers have been having regarding heat or fan related concerns with Early 2011 MacBook Pros. If your MacBook Pro was produced within the last few months the thermal issue has been resolved and it will likely not be in issue for you. If you are still wondering if your computer is effected or what the real issue is keep reading.
    The MacBook Cools itself by 2 main methods: active and passive. The active cooling is via a fan that blows air through a heatsync and into a tube called a heat pipe which leads to the back of the computer where the hot air is discharged through a vent at the bottom of the screen behind the hinge. The fan lowers the air pressure inside the case causing outside air is drawn in the case, displacing the hot air inside and helping to cool the other components.
    The computer uses passive cooling to remove the residual heat from the processor which comes mostly in the form of radiant heat. Passive cooling is also used to cool the other components of the computer (memory, disk drives, battery etc). Passive cooling works by conductive heat transfer ie. syncing to the case of the computer. Some of the heat then is radiated. Some of it is transferred from the outside of the case via convective cooling; the foot pads on the bottom cover are designed to raise it up just enough to allow air underneath for convection to occur. (Convection is the process in which hot air to rises and is displaced by cooler air.) The rest of the heat from the bottom cover is absorbed by whatever surface you have the computer on.
    The processor will not sync to the case very much if the board is assembled properly however the other components of the computer will, requiring the case to be in open air to allow for passive cooling to take place.
    If you have some sort of covering such as a plastic snap on case it will likely interfere with passive cooling in all of it's 3 of it forms, this will cause the computer to be abnormally hot. I recently saw someone in the Apple store with a MacBook Air experiencing abnormal heating due to a plastic snap case so this particular problem is not unique to MacBook Pros and it is not the cause of the issue being discussed here. I do not recommend the use or anything that covers the computer while it is running with the exception of something that covers the back of the display panel only. If you are worried about your computer getting damaged go and buy a laptop insurance policy from Worth Ave group. The insurance does not cover cosmetic damage or misplaced items but will cover accidental damage including spills. This insurance also covers theft, vandalism and natural disasters, is quite inexpensive and the claims process and deductible  is similar to most phone insurance plans (which they also offer).
    User induced overheating can also occur when the computer is placed on an improper surface such as a couch cushion, car seat, bed, pillow etc. Doing this can interfere with both passive and active cooling.
    As I mentioned earlier In all likelihood if your computer was produced after May it is not affected. I personally have been in posession of 3 MacBook Pros, one produced before May which had the problem, one after which had no problems and one produced more recently that has mind blowing thermal performance way beyond all of my expectations.
    So the question at this point is exactly what is the problem, how can it be diagnosed and how can it be rectified.
    After extensive research and testing I have determined the issue to be related to improper application thermal paste. I involuntarily became involved in this pursuit as a result of the problems I was experiencing and I did not initially come at from an objective viewpoint but rather one of cautious skepticism. I had anticipated before purchasing my computer that there may be a thermal issue. This anticipaion came as a result of reading an article on ifixit.com about the disassembly of the brand new early 2011 MacBook Pro. When the technician performing the disassembly removed the main heat sync he expressed concern about how much much thermal paste was present, expressing that it seemed excessive. This lead the technician to question wether or not it would cause heating problems.
    Proper application of thermal paste is critical to the functionality of the active cooling system and when applied improperly will not properly transfer the heat to the heat-sync which in turn gets cooled by the fan. Proper application of thermal paste insures the heat is removed from the case as efficiently as possible. Doing this both reduces the speed at which the fan needs to run in a lot of situations and prevents too much heat from the processor needing to be cooled by passive means. If is is not applied properly it will eventually lead to overheating of the case as well as the other components of the computer. This can cause damage firstly to the computer's battery and can also significantly shorten the life computer. (Or any other kind of electronic device for that matter.)
    The problem can be diagnosed by testing the computer using a program called System Load or any other software that will put your computers proscessor use up to its maximum and keep it there indefinitely. Placing full load on your GPU at the same time during the test is also recommended. Keep in mind, if you are using your computer the fan will spin up if needed for additional cooling. You should expect the fan go up to its maximum speed during the test, it is not in of itself an indication of a negative result. Make sure to have the computer plugged in, fully charged and on a proper surface. A desk or other flat surface should be fine. Exceptions would include the top of a refrigerator since it has insulation just underneath the metal exterior or any surface that is heated by any means such as a dryer or other appliance.
    (The temps to follow are in ºF)
    Run the test for up to 1 hour. If the case of the computer breaks 93 degrees your unit is likely affected. Expect the unit to even possibly reach temps approaching and exceeding 100º, if this happens immediately abort the test. Also look for the processor temp shooting up to around 180 in the first 30 seconds and the fan spinning up right away. Typically on a properly functioning unit the temperature of the case will end up being somewhere in the neighborhood of 88-91º. If this test is preformed in a room with a normal ambient room temperature of about 68 degrees. Even after an hour the case of the computer should not be significantly hot, just warm to the touch. On a normally operating unit the fan will start to kick in within 90 seconds or so and may not reach full speed even after several minuets.
    At one point the case of my computer actually reached 95º during normal web browsing.
    This is a problem that I have had successfully corrected twice by reapplication of thermal paste. The first time was on a machine produced prior to may and the second was after a logic board was replaced at the repair depot. (I suspect the inventory turnover is lower for boards than whole computers resulting in a board from the initial production run being installed in my computer.)
    If you forget everything I just wrote remember this. #1 if you are using your computer hard enough the fan will end up running at high speed at some point. #2 This problem is not in any way related to the design of the MacBook Pro, or its use/application. #3 This mostly not a problem of the CPU being too hot; these Sandy Bridge CPUs are rated for 212ºf and will routinely be in the neighborhood of 200º, this is hotter than other chips but well within design limits. #4 I have done everything in my power to make sure that this problem has been corrected and I have every logical and evidenced based reason to believe it has been resolved in machines produced after may. #5 This is not an Apple acknolidged issue. Technicians will tell you that there is no problem because these higher temps are normal and within operating limits and if they weren't the machine would shut itself off. (This is a bit extreme; just like a lot of other devices such as electronics, toaster ovens and space heaters with thermal overload protection this automatic shutoff is intended to occur when damage or risk of fire is imminent because the device is WAY outside of normal operating paramaters.) They will also not tell you when asked what these limits are, that they know what they are or in some cases that such figures they even exsist.
    I stake my personal and professional reputation on the accuracy of my findings, it is my job as a private consultant to help my clients to resolve complicated and expensive issues just like this one.
    Bottom line if you are having a problem and Apple won't fix it on warranty don't ditch your machine, just pay to have it done yourself. In most cases you can pay have it done at the Apple store. It will probably cost you less than 100.00, and it will not void your warranty as long as the work is done by Apple certified technician. It will be well worth it; after all in spite of this MacBook Pro's are hands down the best portable computers on the market, with an industry leading warranty and support to back it up. On it's worst day Apple's service and support is better than any computer/ consumer electronics company, even on its best day.
    I hope this helps to clarify this issue! I also hope it will help anyone affected to resolve the problem instead of resorting to a refund and settling for something else.

    hello all
    you can try this:
    Go to system preferences > settings > built in display >  see bottom of window.
    check "show mirroring options in the menu bar when available". then click "airplay display" > and select your device.
    That's what happened to my MBP - 15-inch, Late 2011 model.

  • Does the MacBook have the thermal paste "problem"?

    I'm really thinking about saving up my money to get a MacBook, but with all of the thermal paste "problems" with the MacBook Pro, I'm not sure if the MacBook has the same problems. Has anyone with a MacBook taken it apart and examined the thermal paste? I'm hoping that Apple has chnaged their instructions on how much thermal paste to apply in the MacBooks and MacBook Pros. If anyone has done this, or knows of any place on the web with pics of the MacBook taken apart, I would love to hear about it. Thanks in advance!
    -MRCUR
    Message was edited by: MRCUR

    Some people have encountered very excessive amounts of paste on the MacBook as well, and one person out of curiosity went into his 12 inch Powerbook and found it glopped on there too -- and of course a healthy improvement in the thermal performance of the computer once it was done properly. Seems to be an ongoing Apple problem -- but not necessarily a problem in every machine, as some people have found much less excessive paste application and only a minimal improvement in thermal performnce after reapplying.
    The MacBook is very much easier to disassemble than the other machines in part because the logic board and heat sink faces up and therefore you do not need to remove the logic board, but do please note that if you do take it apart, any damage that is deemed to have resulted from your repair will not be covered.

  • My macbook pro froze last night and I held the power button down to restart the computer. Now the computer will not even start up. Any ideas what may have happened?

    While searching the internet last night my Macbook pro froze up and would not respond to anything. I restarted the computer and now the computer will not ecen start up. It will go to the gray screen with the apple sign. It is there working for 10 seconds and finally shuts down again. Any ideas how to get the computer to come back to life?

    Go step by step and test.
    Start up in Safe Mode.
    http://support.apple.com/kb/PH14204?viewlocale=en_US
    Repair Disk
    Steps 2 through 8
    http://support.apple.com/kb/PH5836

  • RSS Feed from rss generator's new app has changed the feed. Now the description of apps is not showing. the rest is the same. Anyone has an idea why ?  and how do I get the description? if I fetch it from itunes pages would that be considered violation of

    RSS Feed from rss generator's new app has changed the feed. Now the description of apps is not showing. the rest is the same. Anyone has an idea why ?  and how do I get the description? if I fetch it from itunes pages would that be considered violation of apple's terms and conditions? Please help

    See this post.
    tt2

  • My problem started when system preferences was unresponsive and would not force quit.  I tryed to restart and got the grey screen, but it never restarted.  I closed the lid and now the screen is blank.  Has anyone had a similar problem after Lion?

    My problem started when system preferences was unresponsive and would not force quit.  I tryed to restart and got the grey screen, but it never restarted.  I closed the lid and now the screen is blank.  Has anyone had a similar problem after Lion installation?

    No, as I have yet to be convinced on Lion.
    Did a permissions repair help from the install DVD?

  • My iphone has fallen into the water 6months ago and there is no apple store in my country so i gave the phone s technical service.but they couldnt repair the phone.and now the battery is swollen.can i replace the phone with the new one in spain?

    My iphone has fallen into the water 6months ago and there is no apple store in my country so i gave the phone s technical service.but they couldnt repair the phone.and now the battery is swollen.can i replace the phone with the new one in spain?

    You can only obtain warranty OR post warranty service in the country of original purchase
    As your iPhone has user damage it has no warranty
    IF the iPhone originated from Spain or another EU country you can get out of warranty service in any EU country

  • I have a MacBook Pro 2007 and I installed Mac OS 10.6 but I lost power in the process and now the mac doesn't recognize my hard drive

    I have a MacBook Pro 2007 and I installed Mac OS 10.6 but I lost power in the process and now the mac doesn't recognize my hard drive, how can I fix this

    I've tried it but since I'm using a USB disk drive it keeps freezing up or showing you a folder blinking folder with a question mark. (?). When I start the mac up I hold the control button until the Mac OS install disk shows up. My hard drive doesn't show up anymore. Is there any other button I have to hold down to bring a different menu up. I have also tried to boot up holding control and C and nothing happens.  Thanks for the help so far

  • I have switched the sim card from one iphone to a different one, and i added my music from my old phone to the used one, now the old music on the used phone won't delete. im really frustrated and annoyed please help

    i have switched the sim card from one iphone to a different one, and i added my music from my old phone to the used one, now the old music on the used phone won't delete. im really frustrated and annoyed please help

    Do you just want to delete the music or wipe the whole phone since you've switched to the other one?
    If you plug the old iPhone into your computer you can remove stuff via iTunes or remove stuff directly from the iPhone too.

  • I edited clips and then re uploaded the rendered versions into the organizer and now the thumbnails aren't showing up. how do i generate the thumbnails?

    I edited clips and then re uploaded the rendered versions into the organizer and now the thumbnails aren't showing up. how do i generate the thumbnails?

    neuron113
    Thanks for the reply with the very helpful details.
    Export from Premiere Elements 12/12.1 Publish+Share/Computer/MPEG with Presets = HDTV 1080p29.97 High Quality
    I suspect that we are in a no win situation here - an Elements Organizer 12 issue.
    With Elements Organizer 11, 10, and 9, I can bring your MPEG2.mpg into the Elements Organizer with thumbnail with
    image. I cannot for Elements 12. And, I am working with the same MPEG2.mpg in Elements Organizer 9.0/9.0.1, 10, 11,
    and 12 on the same computer. In the morning, I will look Elements Organizer 13 as well.
    In my work with 12, this MPEG2.mpg consistently crashed the Elements Organizer 12.
    It is difficult to explain these results by invoking a missing codec theory since all was done with the same sample on the
    same computer.
    More later.
    ATR

  • My iphone fell in to the water and now the wifi is not working

    My iphone fell in to the water and now the wifi is not working .......please help

    Water damage is normally catastrophic to electronic devices.  Turn off the iPhone, place the device in a bag of uncooked white rice, and leave it in there for 5-7 days.

Maybe you are looking for

  • How ro display Form on a table or view

    Hi, I have two forms. Based on form 1 option the form 2 values should be displayed. I have stored procedure and steps in a table with procedure id and step number For example: In a procedure there are multiple steps(step1, step2... step n). If proced

  • Firewire issues after upgrading to 10.6

    I mentioned this is a prior post, and have really still not got a resolution to it. I have a 1st. gen Mac Pro 2 x 2.66 dual core. I have encountered several disturbing issues using Firewire 400/800 devices on my machine after the upgrade. When I boot

  • How can I mange a wireless router behind a wired router?

    I've got cascading routers configured as recommended in Linksys Answer ID #3733.  Wired router BEFSR41 is closest to Internet and wireless WRT54G  is behind it.  I want to mange the wireless router remotely.  Should routers be on the SAME IP segment

  • UWL in Federated Portal Network

    Hi All, Can anyone please suggest how UWL works in case of Federated Portal Network? I have a requirement to show the tasks, alerts, notifications from more then one Producer in the same UWL iview on Consumer. I followed the steps as mentioned in the

  • Iphoto quits unexpectedly upon opening

    I cannot open my iphoto to access and manage my photo file. Whenever I try to do this, while the photos load the computer abruptly displays that the application has unexpectedly quit. THis also happens if I try to load photos from a camera. I can acc