Reauthentication problems in bridging environment

Hello,
I have configured two 1240 APs in bridging mode. One root and the other nonroot. Configured with WPA2 and LEAP with local RADIUS. Reauthentication interval is 120 sec. Everything works fine but when the nonrootbridge has to reauthenticate, it loses one or more pings and comes back again. We want to use VoIP over this link and I think it has to be more stable. Is this a "normal" behavior in bridging mode with leap?
Anybody some hints for me?

Try by resetting the non-root AP

Similar Messages

Having problems with Bridge shutting down after saving photo in PS Cs5,,,,,,,,, Also when i attempt to update either PS or bridge get an error message in Adobe application manger "Error loading updater workflow"

Having problems with Bridge shutting down after saving photo in PS Cs5,,,,,,,,, Also when i attempt to update either PS or bridge get an error message in Adobe application manger "Error loading updater workflow"

Sorry for the late reply. My email firewall has become a little over zealous & sent a lot of my emails straight to my junk email folder, so I have only just now discovered your reply in my junk mail folder.
The only "don't open files exceeding xxx megabytes" instruction I can find in my Prefs, is in the Bridge Prefs for Thumbnails, & mine is set at 1000mb. The biggest files I handle are bigger than 200mb so I should be able to open a few, not just one.
However, this doesn't explain why I can open a psd format file of 180mb, close it, but then can't open a RAW format file of only 26mb immediately after.
I can open the RAW file only if I restart my computer - very annoying!
However, thanks for the advice about the video card & memory.
So, I'm still stuck as to what the issue is.

HELP. ............Hi folks hope some one can help me please.Having a problem in Bridge I open my images in ACR, as I open files in a folder and lets say they are labeled in yellow they are all going back to the camera raw default , in other words no ma

HELP. ............Hi folks hope some one can help me please.Having a problem in Bridge I open my images in ACR, as I open files in a folder and lets say they are labeled in yellow they are all going back to the camera raw default , in other words no matter what work I have done, inc cropping they all go back to ,as they came out of camera. What on earth is happening? I am on PS CS6. I might point out everything was working normally up to yesterday, when this first started.
I recently changed computer to 64bit from 32bit, not sure if this causing the problem or not. Any help would be appreciated.

Robert,
Would you be so kind to rephrase your question with concise, precise information and without any "let's say that" hypotheticals? Sorry, I can't quite follow you.
Also please give exact versions of Photoshop CS6 (13.what.what), of Bridge and of your OS.
Thanks.
BOILERPLATE TEXT:
If you give complete and detailed information about your setup and the issue at hand, such as your platform (Mac or Win), exact versions of your OS, of Photoshop and of Bridge, machine specs, what troubleshooting steps you have taken so far, what error message(s) you receive, if having issues opening raw files also the exact camera make and model that generated them, etc., someone may be able to help you.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

Hi I have been having a problem with Bridge in CS4 recently. So uninstalled CS4 and Lightroom 4.4 and reinstalled them on my Desktop PC. When I turned on Bridge through CS4, My thumb nail images disappeared and a thumb nail icon with CR2 appeared. Now som

Hi I have been having a problem with Bridge in CS4 recently. So uninstalled CS4 and Lightroom 4.4 and reinstalled them on my Desktop PC. When I turned on Bridge through CS4, My thumb nail images disappeared and a thumb nail icon with CR2 appeared. Now some of my images have disappeared from Light room 4.4, but I can find them in CS4 and Bridge now shows some thumb nails as images and some as an icon with CR2. I have spent two weeks going through preferences etc. to find how to resolve my problem. Please can you Help? Meany thanks in advance
Derek Randall

I don't use LR and rarely use the bridge so I can not answers about thumbnails in them, However thumbnails in windows file explorer and windows dialog for CS2 files will only show if you have installed codec into windows that will produce them. Windows does not do CR2 thumbnails on its own. I use FastPictureViewer Codec package for RAW File and PSD files thunbmail support.

Problem with Bridge CC Update

I always get an error message (49).See picture below. But at the same time a had no problems with the update for Photoshop CC 2014. so whats the problem with Bridge CC?

Hi Robert,
Please refer to the link below:
Getting Download Error 49 Bridge Cc
Regards,
Sheena

Problem with Bridge CS4 reading/editing XMP metadata added in Bridge CS6

Please excuse me if this is a dumb/obvious question. I did try searching the forums for similar problems and didn't find anything that seemed to speak to my issue.
I'm having a problem where Bridge CS4 won't read/edit xmp metadata (specifically, keywords and descriptions in the IPTC panel) that I have entered using CS6. it will read some files, not others. The files are all .mp4s. Of these files, I can read/edit IPTC panel metadata for some of them in Bridge CS4; I can add metadata for all of them in CS6. I see no particular pattern in these files to explain what is and isn't read/editable in CS4.
My question is whether this is a compatibility issue between different versions of CS (in this instance, CS4 and CS6). i know it's a tired refrain to blame software when it could easily be user error, in which case I'd be frankly delighted to know what i'm doing wrong. Please bear with me as I give a few more details.
I'm using macs. I've tried this on multiple systems - for instance, on a mac pro 3 which for some reason has both CS4 and CS6 installed, i can add and edit keywords using CS6, but not when using CS4. Again, in CS4, some .mp4 files read/edit, others do not.
Bridge CS4 blames the files and tells me that the selected file cannot store xmp metadata, and that the properties cannot be modified. To be specific, in the metadata panel it says "this property cannot be modified"; in the keyword panel, it says, "This file (zzz.mp4) cannot store xmp metadata. No changes will occur." This seems odd, because I'm able to add xmp metadata for the same files in CS6 on the same computer, and other computers. I know this problem would disappear if all our computers were using CS6 (or CC), but unfortunately that's not a possibility at the moment. Some of them only have CS4.
Computer details (not an exhaustive list, but two instances): mac pro 3.1 running snow leopard, 16GB memory; macbook pro 4.1 running snow leopard, 4GB memory; adobe bridge cs6 (5.0.0.399) and cs4 (3.0.0.464).
Things I have tried:
Permissions - the files are set to read/write for everyone. Given that I can add/edit metadata in CS6, it doesn't seem to be a permission issue.
Purging the cache - other users seem to have had problems adding metadata in Bridge CS4 where purging the cache for affected files solved the problem. Didn't work in this instance.
Upgrading all affected computers to CS6/CC is beyond my control. I need to figure out why CS4 won't let me read/add/edit xmp metadata, if only for the sake of understanding the broader implications for interoperability.
Any helpful suggestions would be much appreciated.
Thanks,
Kevin

adobe bridge cs6 (5.0.0.399) and cs4 (3.0.0.464).
Without having experience with mp4 files and metadata my observation is that you certainly have not updated Bridge CS6 ( should be 5.0.2.4) and I believe also not the latest version of CS4, can't imaging this also stayed at .0.0 so first try to update both.
And if CS4 can read the data of some files it should be capable of reading them all. Be sure to have the files completely cached first, can take a while.
Other things to try in CS4 is refresh preferences (hold down option key while restarting Bridge and choose reset prefs).
And also check for hidden cache files using menu view/show hidden files. Sometimes those cache files can be troublesome between versions.
If purge cache did not work and reset prefs also failed consider to also delete Bridge plist file and Bridge cache file manual (from user library)

Urgent! Problems with bridge JDBC-ODBC

Hello,
I have found out that JDBC-ODBC bridge in JDK 1.4.1 don't works fine, because, if you want to store text largest 254 characters in a field type text in one record of a Access database's table, it generate a SQLError, I have tried with EasySoft JDBC_ODBC and it works, with it I could store text fields largest than 254 characters, but I have new problems, EasySoft bridge is not free, and don't let store nulls in fields type Date [with PreparedStatement x, x.setDate(theDate)] (raise a SQLError), in the other hand, JDKs bridge do it. Somebody knows if exists JDCB-ODBC free drivers more suitables than JDK's includes, or if exists upgrades?
Is very urgent!, Thanks a lot
(Sorry, my english is very poor)

I have tried it, Is there where I found the EasySoft's JDBC-ODBC driver, but the result is: one problems out, yes, now with this driver I can store String largest 254 characters in fields type MEMO of a table in Access Database, but two new problems, 1st. is a trial version, (requiere paid), and 2nd. don't let store nulls in fields type Date when JDKs JDBC-ODBC bridge lets, and the aplication needs leave this fields blanks.
Any other idea?
Thank

New pc with windows 8.1, downloaded and installed cs5,no problem open bridge and cs5, but can't read raw file , try to update, can't complete or failed updating, please help

new pc with windows 8.1, downloaded and installed cs5,no problem open bridge and cs5, but can't read raw file , try to update, can't complete or failed updating, please help

Sounds like you somehow got the mac version.
Download the windows 6.7 camera raw update from this link:
Adobe - Photoshop : For Windows : Camera Raw 6.7 Update

Problem with Bridge CC

When I open my cr2 files in bridge cc they are opened in CS6 instead of in CC as before. I have recently uninstaled CS5 which I never use. Also when I open my jpeg files in bridge and photshop cc they are opened in another program. Please does anyone have a solution to this

Thanks for the prompt reply. This seems to have solved the problem.
Ursprungligt meddelande----
Från: [email protected]
Datum: 2013-12-01 01:24
Till: "norman_nichols"<[email protected]>
Ärende: problem with Bridge CC
Re: problem with Bridge CC created by Curt Y in Bridge General Discussion - View the full discussion
By uninstalling the previous version you have fouled up the file association. You can try the manual method of preferences/file type assoications and changing the default. If this does not work there are other ways that involve more work.
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5888291#5888291
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/5888291#5888291
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/5888291#5888291. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Bridge General Discussion at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

Frustrating problem with Bridge 6.1.0

I have been experiencing a frustrating problem with Bridge 6.1.0 and previous versions. Soemtimes when I save a file to a particular folder, the file is present in the Finder window, but is not visible in Bridge. If I move the file from Finder to Bridge by draging it there, then it shows up but it is so frustrating to have to do it this way. I have tried to use the «Refresh» function in Bridge but that does not help. All scripts are turned on in Preferences- I have Mac OS X 10.9.4

The current version will not run on Mac OS 10.6.8. Thanks for any assistance.
The easiest way would be to update to at least 10.7.5 (supported on most older Macs) but maybe you have strong reasons not to do so, however it will put you in to more trouble in the future because newer applications have more often the habit of not being able to support older OS versions due to limitations of this old OS.
Here is the announcement of Adobe:
http://blogs.adobe.com/creativecloud/moving-ahead-with-mac-os-x-10-7-and-higher/
However PS CC should still work on your system and otherwise CS6 should. As a cloud subscriber you still have access to both CC and CS6 on the Adobe CC download pages. But only PS is a major upgrade (changed to version 2014) and Bridge has just a minor update and should still work on 10.6.8 I would think?
Installing the updates and upgrades did not remove or uninstall the CC versions of PS, otherwise use CC application to install CC again.

Problems adding Bridge Data to prepaid (Allset) iPhone5

Anyone having problems trying to add bridge data to a prepaid (Allset) phone. I've tried to add 3GB to my iPhone 5 all day today and I've had no success. I've tried doing through (1) the new My Verizon Mobile App, (2) dialing *611 and following the prompts and (3) on my PC while logged into my "My Verizon" account. All three methods result in a "system error" and I can't add any bridge data. The only thing that worked, was it allowed me to put $25 on account by charging my credit card. So now I've been taken for $25 and can't do anything with the money on now have in my account. A call to customer service was a complete waste of time. The CSR told me to do the *228 Activation code on my 4G LTE iPhone 5. I'm not a CSR and I know you don't use *228 on an a 4G iPhone! After wasting 30 minutes and being told my SIM card "had to age" (very creative), I got tired of the snow job and hung up. Is anyone else having problems adding bridge data? Please advise if you have succeeded in adding bridge data today.

Why have a Prepaid forum that is not monitored by CSR's who can actually do something about the issues posted by Prepaid customers? I'm not looking for a "sorry to hear about your problem" reply, I'm looking for answers/solutions.
What a ridiculous arrangement. This Prepaid sub-forum should be deleted so customers don't waste their time posting problems here.
Sent from my iPad

Immer wieder Cach Probleme in Bridge

Hallo,
ich habe immer wieder Cach Problem, obwohl ich den Cach mittlerweile in das Verzeichnis exportiere. Habe gestern gerade den Cach geleert und für 1800 Bilder neu eingelesen. Heute nun wieder das selbe: Das Suchen nach Bilder mit einer bestimmten Bewertung war nach einiger Zeit nicht mehr möglich.
Langsam frage ich mich, ob Bridge überhaupt das richtige Tool dafür ist, denn diese andauernden Cach Probleme in Bridge haben mich schon Tage an Zusatzarbeit gekostet.
Für Hinweise wäre ich sehr dankbar.
Gruß
Claus Tropitzsch

Zuerst hatte ich das hier bereits beschriebe Problem mit dem immer wieder erneuten Drehen von Hochformat Fotos. Eines war dabei, welches schließlich sogar spiegelverkehrt war. Ich habe deshalb mittlerweile diese Bilder aus Digitalkameras als schreibgeschützt, was das Arbeiten sehr erschwert.
Neuerdings ist jetzt scheinbar der neu erstellte Cach so defekt, dass die Suchfuntkion nicht mehr geht und es kommen auch Meldungen, dass die Datenbank defekt sei. Ich wußte nicht, dass da eine DB dehinter steht. Da hilft dann nur Zentraler Cach bereinigen. Dabei gehen dann aber auch bei JPGs ein Teil der Bewertungen verloren (hauptsächlich die mit 2 und 3 Sternen).

Problem with Bridge CS6 and MCXRedirector (OS X 10.9.5)

Good afternoon all, I have a very irritating issue with Bridge CS6 that I've pretty much given up on now, so I'm wondering if anyone out there can help me before I do.
The issue lies with Bridge CS6 running in a networked Mac environment, first, a little background: I am using OS X Server's Workgroup Manager facility for various restrictions and folder redirection. Our users had a nasty bug a little while ago that caused saved Photoshop files to end up in ~/Library/Caches/TemporaryItems instead of the actual network home location they selected to save in. While this was happening, a single entry was being used in the MCXRedirectory preference to redirect the entire of ~/Library/Caches/
This was resolved by changing that preference and branching it out a little more, so now the folders subject to redirection are as follows:
~/Library/Caches/Adobe
~/Library/Caches/Adobe Camera Raw
~/Library/Caches/Meta
~/Library/Application Support/Adobe
Doing this fixed the saving issue with Photoshop, but has in turn broken Bridge. When launched, Bridge immediately fails with the error "Adobe Bridge CS6 quit unexpectedly" and gives the three options to ignore, report or reopen.
Taking away the ~/Library/Caches/Adobe redirection allows Bridge to work as normal again, but then I'm back to square one with Photoshop files saving in TemporaryItems again.
Does anyone have any advice to remedy this annoying problem please?
Thanks in advance.
EDIT: Bridge version is 5.0.2.4

Sorry, did not solve the problem. The info given did not bear much relation to what I could see in the print drop down box. I have been through all settings I can access and every thing appears normal. The print preview in the print box appears normal and shows colour, but this does not translate to the actual print.
When printing a docuement of 3 pages or more using double sided the result is the first docuement page on one side of a sheet and the last page on the other side, but upside down, despite orientation set to long edge binding. All other pages between first and last are ignored.
When printing docuements originating from printer software such as Print Quality Diagnostic and Make The Most Of Your Printer, the printer performs correctly with good quality printing and colour.
I assume that the Mac update to 10.9.5 has corrupted something but I am not knowkedgeable enough to understand what. Any further assistance would be greatly appreciated.

Playbook Upgrade to 2.0.0.3778 problems lost Bridge

Hello,
I counld use some help, plugged in my playbook today to sync as usual, and an upgrade notification came up so i clicked ok, after about an hour it rebooted and looked like everything was fine until i tried to use my email/bbm and anything else of the Blackberry Bridge and it all came up cannot connect to server, any ideas what i need to to please? I did try the below and as soon as it booted it made me upgrade back to the 2.0.0.3778 version......any help would be appreciated. thanks in advance
Turn off your device.
Open BlackBerry® Desktop Manager.
Connect your device to your computer via USB.
Enter your device password.
Enter your email address or uncheck “Yes, email me when updates are available”.
Click Install.

jams1361 wrote:
thanks, that definetly does the trivk for now, when do you think i will be able to actually use the correct icons to access ?
When OS 2 is released to public it should be fixed, for now its a developer version for testing andriod apps.
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

Problem with bridge and getting internet on android

My ISP uses a modem/router that's mounted outside of my house. From there it runs into my Linksys E1200. Since it's a router connected to a router I have to use it as an access point. I don't have any cable connected to the internet port in other words.
So I get a cheap LG Adroid for wifi only. The phone hasn't been activated and it doesn't have a service plan. The wifi works on it though as I've connected and used the wifi at businesses that provide it for free.
My desktop is wired with a ethernet cable. My notebook is wireless and it connects and get the internet. So ISP router> Linksys in bridge mode. The cable from the router can be put in any port but it's in a yellow one. My notebook on the other side of the house conected via wifi and getting the internet.
My problem is the phone. No matter what I've tried it connects to the router but I end up getting a "Internet not availible: message shortly after. I didn't know whether to use the Linksys IP info to setup on the phone or the IP of my ISP's router/modem. I've tried to enter both on the phone when modifying the network.
I unplugged everything but my desktop and connected it to the Linksys. Did ipconfig /all. Used a browser to get to the Linksys setup. Set it in bridge mode. Disabled DCHP. All security is disabled., including the WPS that's a feature on my router. Specified my own IP info in the setup tab, using the information I got from the ipconfig. Rehooked up the cables in the back. All is well. I have internet o nthe desktop and the notebook, just not the phone. To get to the Linksys setup page I not longer do the 198.162.1.1. I enter the gateway of my isp's modem/router.
I've entered all of this same information on the phone with a static connection instead of DCHP.Choose a IP that was a few digits higher than the gateway. I still get the "Internet not availible" that Cisco reports back. On the desktop I pinged the IP I assinged my phone. Packets are recieved. I can aslo acces the Linksys setup page on my phone so it really is connecting to the router.
I'm at my wits end. I've tried different things, too many to remember. If anyone has any idea I would appreciate it.
Solved!
Go to Solution.

No the phone should get it's IP from your DHCP server.
The IP Address of the Linksys is just so you can access it and has nothing to do with the network. You turned it into a repeater\switch.
What is your DHCP server's IP Address and DHCP range? This info will basically spell things out.
If you plug a computer into one of the Linksys lan ports it should work normally and so should the wireless devices in that case
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Reauthentication problems in bridging environment

Similar Messages

Maybe you are looking for