Receive wireless signal and pass through via ethernet

Hi,
I'd like to know if it's possible to pass through internet via ethernet from a Time Capsule that receives a Wireless signal.
How can I do this?
Thanks!

Well, to be more specific, this a scheme of what I'm trying to do (it represents the floors in my house):
[URL=http://minus.com/liKoug8pFOaFN][IMG]http://i.minus.com/jiKoug8pFOaFN.jpg[/IMG][/URL]
So;
- Telenet modem wired to D-link wireless router.
- D-link router to AE (wireless)
- AE to stereo (wired)
- D-link router to TC (wireless)
- TC to PC (wired)
- TC to printer (USB)
- D-link to tv (wired)
- D-link to Digibox (digital television - wired)
I want to be able to stream music from every device on the netwerk (iPad, iPhone, MBP, ..)
and print from every device. All music should be streamed from iTunes Library on TC.
I hope this is clear
Thanks in advance!

Similar Messages

Airport Extreme wont pass internet through via ethernet OR wireless ...

I have an iMac in my house that can receive internet flawlessly when plugged directly into my ethernet jack in the wall (connected to my router). I can fwd (share) that through airport to my computers in my detached garage.
I have a spare AExtreme i plugged into the ethernet wall connector and then to the iMac and internet pages wouldn't load nor would wifi airport work when joined to that AE network.
My routers firmware is on the latest edition so i dont think that's it. This AE has been sitting in the box for months so maybe its software/firmware is out of date? how do i update AE firmware?
Any clues as to whats my issue?

I am running into the same problem.
My setup was working fine until a few days ago when I noticed the flashing amber.
My setup is/was:
iMac 2GHz Intel Core2Duo
OS X 10.5.2
Airport Extreme Gigabit
Comcast Cable: Modem to AE via ethernet - AE to iMac via Ethernet - AE wireless to powerbooks.
(This setup was working fine for the last 2 months when i bought the AE - I was not using Airport on the imac since i was connecting via ethernet.
Now using that setup, I get a green light on the AE, Network status via System Pref all seem OK, but cannot connect.
Right now, I can only connect directly via ethernet to my modem. I turned on the iMac Airport, it recognized the AE and downloaded a firmware update. But this did not change the situation. I did do a reset a couple of times, as well as just left the AE off all day.
Not sure what to do next. I am currently using internet sharing sparingly in the house via iMac airport.
HELP

Dolby digital pass-through via digital input - static

anybody try to hook up a dolby digital 5.1 source (i'm using a dish network vip622 dvr receiver) into the mac mini's digital input and pass the signal through to the speakers connected to the mini? i'm doing this but all i get is static - presumably because there is no decoder inside the mini.

forgot to say - i'm also using linein from rogue amoeba
http://rogueamoeba.com/freebies/
sj

Setup Time Capsule as wireless device and Time Machine with Ethernet?

I'm running the latest version of Airport Utility (6.3.4) with a TC a1254 and Macbook Pro platinum late 2007.
I have a modem/router Ryge model Wa41r.
Ive tried everything I could find in the forums and in expert pages and can't configure my Time Capsule as a Wireless Device connected to the modem/router and Time Machine with Ethernet Cable.
I tried letting it configure itself, it held the wifi signal for over 5 min then turned off. Never that way worked again.
Then I configured with other examples seen in Apple communities and expert Apple pages, but it conflicted with my routers signal. I turned off the Wireless Lan Interface and it turned off the Ethernet cable with the connection as well. I tried giving my TC different IP address.
So my Time Capsule gives me this status in flicking amber: Internet connection and Conflicting DCHP Range. (when I connect to my Mac the Internet works)
And strangely the wireless signal appears in my Macbook but not in my Android Phone.
Works fine doing backups when asked via ethernet.
Also when I go to check on it on Airport Utility in other wifi devices it appears but says "Device Not Found - device name- was previously part of your network. Check that is still in range...etc"

I would like to help you but you need to clear up some things..
A Time Capsule is plugged into the network by ethernet.. you back up to it using wireless or ethernet.. it should make no difference which.
When you say this..
Ive tried everything I could find in the forums and in expert pages and can't configure my Time Capsule as a Wireless Device connected to the modem/router and Time Machine with Ethernet Cable.
I cannot understand.. The Time Capsule plugs into the main modem router.. and should be in bridge mode..
Time Machine is not hardware.. it is the backup software on the computer.. there is no way you can connect Time Machine with ethernet cable. .you can connect the computer with Ethernet Cable..
But you need to clarify please.
If you wish to connect TC to the Modem router by wireless this is not possible. It must connect by ethernet.
You can connect your computer to it using either wireless or ethernet.
And strangely the wireless signal appears in my Macbook but not in my Android Phone.
It is likely the wireless name is not valid.
Make sure all names are short, no spaces and pure alphanumeric. 2-20 characters.. Do not use the Apple recommended names.. they can be totally wrong.
Also the password for wireless should be 8-20 characters but same rules.. pure alphanumeric mixed case and numbers.
Start again.
Factory reset the TC.
Factory reset universal
Power off the TC.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the TC to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
N.B. None of your files on the hard disk of the TC are deleted.. this simply clears out the router settings of the TC.
Plug it into the main router by ethernet.
Do the setup via the airport utility in a Mac or iOS device.
Follow the setup instructions above.
Then you can connect to the TC LAN ports by ethernet or use wireless on the computer.
Your modem WA41R. I cannot find details in English . .they are all Spanish so we may be having difficulty of language here.
But if the modem is working as router the TC has to be in bridge mode.. it will not work properly in router mode.
So you should see it set as bridge here.

Airport Extreme Sharing printer to Leopard and Windows 7 via Ethernet port.

Hello!
My home office is in a mixed environment, 1 iMac with Leopard 10.5.8, and the other iMac running Windows 7 Ultimate x64 on bootcamp. Both computers are connected to the Airport Extreme (dual band version, firmware 7.4.2) via Ethernet. I attached the HP LaserJet P1006 to the Airport's usb port in order to share the printer to both platforms.
My problem is that, I got the printer installed on Win 7 by using bonjour print service v2.02 without any problem as it said works in both Ethernet and wireless, I sent a print test from win 7 successfully, then I did another test from leopard ( as I presumed it should works also), however, it says "the printer is in use". and wouldn't print. I tried restart the Airport Extreme and tried print from leopard again and that was fine but then Win 7 couldn't print.
Is there any solution for Mac + Win environment like my description? If I have 2 computers running on OS X they print perfectly well. Thanks all!
My solution for now is to physically plugging the printer to where I need to print from. I use Ethernet wired both computers is because I want to take the advantage of the gigabyte lan port for speedy files transfer between both computers.

If networking isn't working out for you, you may want to try out a swtich. Best Buy sells one by IOGEAR that allows for two USB connections to tie into one computer. So long as windows 7 can either download its own driver for the printer for basic features, or if you want to download canon's driver this solution will work. The only draw back is having to bring the laptop near the printer when you need to print.
IOGEAR SWITCH
MX860 Drivers and Support Page
My opinions do not in any way shape or form represent Best Buy's Official decisions.

Extend Wireless Network with Two Airports Via Ethernet?

I would like to know if you can extend a wireless network using an ethernet cable between two Airport devices.
There are a couple of reasons why Id like to do this:
Im thinking that because the additional basestation (Airport Extreme) is hardwired to the main Airport (Time Capsule, plugged directly into my cable modem), it doesnt rely on a Wi-Fi signal source, so the network speed wouldnt be degraded as it does when you normally extend a Wi-Fi network over the air. And possibly the range would be a little better? Id still be using Airport network for my iDevices.
Id like to use the Extreme as a router to hook up other devices such as a TiVo, TiVo Stream and Xbox 360. I'd prefer these devices be hardwired to the network (and actually the TiVo Stream requires that it be).
How would you set this up while keeping everything on the same network? Is this even possible?
Currently my setup looks like this: Cable Modem<ethernet>Time Capsule<ethernet>Airport Extreme:<ethernet>TiVo,<ethernet>TiVo Stream,<ethernet>Xbox 360

In addition to John Galt's suggestion, there is another very simple and quick way to verify that your AirPort Extreme is "extending" correctly.
Locate your Mac laptop near the main router first....in your case, it would be the Time Capsule and log on to the wireless.
Hold down the option key on your Mac while you click on the AirPort icon
Look for the BSSID and jot down the last few numbers. That is the AirPort ID of the Time Capsule.
Now move your laptop close to the AirPort Extreme and perform the same test. If you see the same BSSID as you did before.....the AirPort Extreme is not extending, since your laptop is still picking up the wireless signal from the Time Capsule.
If you see a different BSSID, that will confirm that the laptop is picking up a wireless signal from the extending AirPort Extreme.
Try to minimize obstructions between wireless devices and the access points to which they are connecting.

Connecting aiport extreme and airport express via ethernet cable ?

Is it possible to connect an airport extreme to an airport express via ethernet cable, I ask because I want to expand the range of my wifi network to the basement of my house, the floors are really thick concrete so I installed some ethernet cable runs, I hope somebody can help me, thank you.

+How do I do it ? Do I connect the modem to the airport extreme and then run the ethernet cable from one of the extreme's ethernet ports to the express ethernet on the basememt and a second cable from another of the extreme's ethernet connectors to the express on the second floor+
Yes, this is exactly correct.
To configure each AirPort Express (AX)
Open AirPort Utility, click Manual Setup
Click the Base Station tab below the icons to name your device, assign a device password and adjust time zone settings. Give each Express a separate name so you can identify then easily.
Click the Wireless tab
Wireless Mode...Create a Wireless Network
Wireless Network Name...Exact same name as your AirPort Extreme network
Radio Mode 802.11n (802.11b/g compatible) if you want to use 2.4 GHz
Channel...Automatic
Wireless Security...Exact same setting as your AirPort Extreme network
Wireless Password....Exact same setting as your AirPort Extreme network
Click the Internet icon
Change the Connection Sharing setting at the bottom to "Off (Bridge Mode)"
Click Update at the lower right and the AirPort Express will restart in 20-30 seconds
I think it is easier to configure each AirPort Express with AirPort Utility by temporarily connecting it to your computer with a short ethernet cable. Once you have saved the configuration, you can move the Express to the location that you need.
Please post back on your progress.

IMAC and MacBook connected via ethernet. Can see "Bob's" public folder on "Betty" but not allowed to move or open files. Want to Bob-- Betty (my new computer) permanently. Adjusted "permissions" everywhere I think

Old computer HDD named Bob, new one named Betty. Trying to transfer crucial files via ethernet. Have connection, can see Bob's public folder on Betty. When try to move or open anything there, tells me I do not have permission to either view or read respectively. I changed permission on the item to read/write for Betty. Made Betty an admin on Bob etc. What can I do?
Thank you!

Do have file sharing and remote login checked
When on Betty's computer, Sign into Bob's computer with Bob's username & Bob's Password, instead of Betty's.
BINGO!!!! Problem solved. Many thanks!!!

Connecting ibook and Power Mac via Ethernet

Is it possible to connect my ibook g4, with my Power Mac G4 via ethernet? I simply want to make it so I can swap files between the two. They're both running Tiger, 10.4.11, if that means anything at all. Any help would be greatly appreciated.

Mac OS X file sharing ( hope you know another language than english ). You need to go into sharing & turn on file sharing. It will share your public folder.
http://docs.info.apple.com/article.html?artnum=106461
The Mac OS client shares the the public folder. You may try putting an alias in your public folder to the flash drive. To share the flash drive directly, you need SharePoints.
The Mac OS X client version contains most of the sharing software. It doesn't contain an extensive GUI for manipulating the software configuration.
"SharePoints is an application or a preference pane that makes it easy to add and delete share points like in the old Finder. In Mac OS X, by default, you are limited to sharing only what is in your public folder in your home directory. This program makes it easy to share any folder."
http://www.hornware.com/sharepoints/
Mac OS includes support for NFS, the native Unix network file sharing system. You may share files between Mac OS X systems with NFS as well as other Unix Systems. However, the documentation on how you make the shares is rather limited. Once you learn how to configure the net info database with the netinfo command, the shares are not too hard to make.
"NFS Manager is a graphical user interface to control all built-in NFS features of Mac OS X. "
http://www.bresink.de/osx/NFSManager.html

PSC 10 and Pass Through Services - Override the GO button

I have a couple of questions around the presentation of the service offer and the service form pages.
What I am trying to demonstrate for a prospective customer is a “pass-through” service where there is no order form but a link off the central PSC catalog to another website location. First off, if there is a correct way to do this please recommend it. This is what I think would be the way I would like to handle it:
     1.       Set the service to be non-orderable. This removes the “Order” and “Order on Behalf” buttons with a “Go” Button as shown here:
     2.       Next I would populate what was the HTML that describes the details of the service from the other website in the Overview from the service designer service presentation tab so that it displays in the Specification of the Offer page.
     3.       Next I would like the Go button to launch “pass-through” to the other web site. Currently it pulls up an empty form with the service description and a “Cancel” button. Is this possible?
     4.       Is there a way to control the layout of the content on the Offer Page and the Service Order Form pages? For instance, if I wanted to include the “More Details” from the service designer service presentation tab, would that be possible?

If you make the service non-orderable, but the user still has permission to see the service, he will see the service and the "Go" button. Clicking on the "Go" button is supposed to take you to the order form, which allows the end users to see the fields he/she needs to fill in, but does not have a "Submit" button.
I don't currently have a "Yes" answer for #3 and #4. There might be a way to do them. I'll look into it.

OVM support for NPIV and pass through disks

Hi Gurus,
I have a couple of questions -
1) Does OVM support NPIV?
2) Does mapping the physical disks via the phy: definition in the vm.cfg file equivalent of pass through disks to the guest OS?.
thanks!
Gak

avasek wrote:
Thanks!. The pass through question was actually in context of usage with snap* products from netapp as they work with VMware. All the snap* work with RDM's in VM's (pass through's), so i was wondering if the snap* could be made to work with the phy: def to the VM's as well. The RDM def should be equivalent of the phy: def ..right?. So ideally, they ought to work?No idea, to be honest -- I haven't worked with NetApp gear yet. You're probably better off checking with NetApp directly as well.

IPhone not receiving wireless signal

It keeps on saying Searching. I am on Verizon and within area with service. It has not worked since updating to iOS 6.0.2

I know this may seem stupid, but did you try unplugging the router and then plugging it in again? That's always the first line of elimination. If you have, then try replacing the router, there may be something wrong with it. If both the MacBook Pro and the iPhone cannot recognize the wireless signal, there is an issue with the router. Security should have nothing to do with the devices recognizing the signal, just whether you are able to use the network or not. Nothing masks the signal from other wireless devices. (In other words, it will always show up in any WiFi devices "available networks" section.) The only way it would not recognize it is if the Wireless bands don't match. (i.e. Wireless G device with a Wireless N device). However, the majority of the upgrade wireless bands work backwards. I suggest switching the Belkin out for a Linksys, Netgear or AirPort and see what happens. I'm putting my money on the issue being the router.

SG200 serie tagged paquets untagged and passed through PVID

Hi,
I just beggin support for a new office using 5 SG200, 3 50-24P and 2 26-12P.
I'm trying to configure 2 VLAN on the same port. VLAN 1 is defaut VLAN and PVID for every interfaces and I want to add tagged VLAN 50 to every interfaces for VoIP phone (phone with switch and PC connected through phone). I want the 2 VLAN to be completly isolated and only be able to communicate between others by passing through my router.
I created VLAN 50 and added it to every interfaces (I don't know which interface goes to which local in the office), and it work fine on a switch (a 50-24P) but not on the other I tryed (a other 50-24P and a 26-12P). The two other switch are in the back of the factory so I didn't tryed them for now.
I found only one difference in the config, the default VLAN on the working switch is 2 instead of 1. The only other difference I also saw was the firmware version, 1.0.0.19 on the switch working fine and 1.1.2 and the 2 others. I think it must be somthing else since 1.1.2 is still available for download even if not the latest.
Working fine switch configuration :
All port are 2U, 50T in trunk mode.
Those that untag the tagged VLAN :
All port are 1UP, 50T in trunk mode.
The P seem only related to firmware version since every interfaces PVID is configured as 1.
I read the manual VLAN port twice but can't find where the problem is.
Help would be really appreciated on this.
Thanks

Thanks Ciscomax for the answer.
Why smartport would help me ? From what I saw on the manual, it seem only to replicate the config of a interface to multiple interface for fast and easy depoyment. Am I missing something ? For the voice VLAN, seem like the VLAN must be created first and functionnal. Configuring it as voice VLAN only seem to apply QoS automaticly. Am I also missing somthing else here ?
Also, why trunking should have the same VLAN ID ? It's untagged so it can change of VLAN from one switch to a other compared to tagged VLAN that can't. Sure it make things more complexe but it's already working and it won't change anything for VLAN 50 if I change default VLAN. Also, the switch that don't use the same default VLAN is the only one that act as expected with VLAN 50.
Finally, thanks for link but like already writen on my first post, I already read the manual (the VLAN part twice).

WRT54G2 slows computer receiving wireless signal

Basically, i got a desktop computer connected to the modem n router with a laptop and ps3 receiving the signal. Internet works fine on all 3 seperately but the problem only occurs when the desktop computer is on the internet. When its on, the internet on the laptop works but is very slow and receives constant 'the connection has been reset' errors in the browser and also has trouble signing in to msn. With the ps3, the internet doesn't work at all with the desktop on the internet. Anyone know wuts wrong??

Upgrading the router's firmware might help you...Download the Firmware from here , Follow these steps to upgrade the firmware on the device: -
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router and check if your problem is resolved...

Calling a new browser window with WD Abap and passing data via POST

Hi there,
does anybody know whether passing data via POST method is possible when opening a new browser window from within a Web Dynpro Component? In my case I use method IF_WD_WINDOW_MANAGER->CREATE_EXTERNAL_WINDOW for opening a new browser window. Now I want to pass a big amount of data which is only possible via POST method. How can I achieve that or is it not considered inside the Web Dynpro Framework?
Kind regards,
Albert

Hi Priya,
can you please explain a little bit more what you mean? I didn't get it..
Kind regards,
Albert

Receive wireless signal and pass through via ethernet

Similar Messages

Maybe you are looking for