Receiving a continuous status error with the FP1600 module.
I have 3 banks of terminals. All three banks use a FP-1600 module as the network interface. All three banks operate when I power the modules. However, after roughly 15min to a half hour, bank number 1 experiences a continuous red blinking status error, followed by total communication loss to Labview (there is still power to the terminal). The only way to re-establish communication is to cycle the power. This bank contains 3, AO-200 modules; 1, AO-210 module; 2, AI-111 modules; 1, AI-110 module, and 1 RLY-420 module. All modules are powered the same, and the others have never lost communication.
Prashant,
I would contact the National Instruments support by phone, as you may need to return the FP-1600 for repair.
http://sine.ni.com/apps/we/niae_asc.main
Communication Methodhone NI
Regards,
Cyril Bouton
Applications Engineer
National Instruments
Cyril Bouton
Active LabVIEW Developper
Similar Messages
-
Error with the function module REUSE_ALV_GRID_DISPLAY
Hi,
While using the fucntion module REUSE_ALV_GRID_DISPLAY
I am getting the below error.
Message i407(0k) with l_template_om.
message says 'Contact your system administrator. The following template is missing: sap_mm.123
Kindly provide me the reason why this success message is displayed for this function module.
Vijayat first its an information message sind its of type I and not of type S which would be success.
this message is beeing displayed because that template is really missing, believe it when SAP talks to you.
So talk to your basis guys.
to come around this problem without talking to your basis guys, i´d propose to use CL_SALV_TABLE or CL_GUI_ALV_GRID to display an ALV. -
System_failure error with the function module HTTP_POST
Hi Friends,
While executing the function module "HTTP_POST" ,sometime we are getting the error "System_Failure" exception.
Can anyone tell what could be the reason for this exception,any configurations need to be done on SAP???
For this FM we are passing the RFC destination"SAPHTTPA" as one of the paratmeter and
The two import paramters we are passing to this FM are
URI :
http://10.74.40.31:8686/ArchiveBridge/?informaticaArchive&contRep=IA&sumFile=MYTA_SUMMARY_20090820063258.sum
Destintion : SAPHTTPA
Thanks all in advance.
Regards
DharmarajuHi,
Check if any proxy is maitained in the client by going into transaction
SICF-> Goto-> HTTP Client Proxy -> HTTP LOG TAB.
If there is anything maintained under Host name and port, if yes you need to specify the IP address while calling FM HTTP_POST
under PROXY as
192.168.0.1:8080 where first part is IP address & 2nd part(8080) is port.
Also test connection for SAPHTTPA under SM59 to see if its properly configured.
Regards,
Amit -
[SOLVED] Error with the php5 module for apache
Hi!
I've installed Apache 2.0.55-1 and PHP5 5.1.4-4. When I try to run the apache server it fails. Then I do httpd -k start and I get:
Syntax error on line 262 of /etc/httpd/conf/httpd.conf:
API module structure `php5_module' in file /usr/lib/apache/libphp5.so is garbled - perhaps this is not an Apache module DSO?
The file libphp5 exists, but seems corrupted.
See you
NeOnsKuLLThat version of the package has been built with apache 2.2.x. Be sure to use that version of apache too, as 2.0 won't work with that specific package.
-
Error with the Receiver JMS Adapter (Connection On-Demand feature)
Hi,
In high volume we are experiencing errors with the Receiver JMS Adapter and the connection On-demand feature:
Adapter Framework caught exception: while trying to invoke the method com.sap.aii.adapter.jms.api.connector.DisconnectorListener.notifyEvent(java.lang.String) of an object loaded from local variable 'listener'
Delivering the message to the application using connection JMS_http://sap.com/xi/XI/System failed, due to: com.sap.engine.interfaces.messaging.api.exception.MessagingException: while trying to invoke the method com.sap.aii.adapter.jms.api.connector.DisconnectorListener.notifyEvent(java.lang.String) of an object loaded from local variable 'listener'.
The message status was set to WAIT.
Looks like the message is successfuly reprocess after the wait period but the ALEAUD/Akcnowledgment are not successful in the sender ECC system. (SAP -> PI - > JMS)
Any idea?
PI 7.1 EHP1
Thanks,
Martin
/people/sunil.ojha5/blog/2010/08/31/review-of-sap-pi-jms-adapter-on-demand-connection-feature
Edited by: Martin Lavoie Rousseau on Jun 3, 2011 3:21 PMPlease ensure to have specified an User and password to connect to JMS server (don't leave the fields empty).
-
Communication error with the opmn server local port
Working on 64-bit R12.0.6 on AIX 5L
Application services are not being started properly. They are being started with status 2(sometimes with 4).
Autocinfig is being successfully completed.
Please help me how I can get rid of this error. Following are some of the environment setting details:
ons.conf
nodes=appaix02.us.oracle.com:15007
opmn.xml
<opmn xmlns="http://www.oracle.com/ias-instance">
<notification-server>
<port local="15006" remote="15007" request="15005"/>
opmn.log
OPMN worker process exited with status 4. Restarting
OPMN worker process exited with status 4. Restarting
OPMN worker process exited with status 4. Restarting
OPMN worker process exited with status 4. Restarting
OPMN worker process exited with status 4. Restarting
OPMN worker process exited with status 4. Restarting
ons.log
07/01/11 13:12:02 [4] ONS server initiated
07/01/11 13:12:52 [4] Logging disabled
07/01/11 13:12:53 [4] ONS server initiated
07/01/11 13:13:04 [4] Logging disabled
07/01/11 13:13:04 [4] ONS server initiated
07/01/11 13:13:17 [4] Logging disabled
07/01/11 13:13:28 [4] ONS server initiated
07/01/11 13:13:40 [4] Logging disabled
07/01/11 13:13:41 [4] ONS server initiated
07/01/11 13:14:20 [4] Logging disabled
07/01/11 13:14:21 [4] ONS server initiated
07/01/11 13:14:29 [4] Logging disabled
07/01/11 13:14:29 [4] ONS server initiated
07/01/11 13:14:34 [4] Logging disabled
07/01/11 13:14:34 [4] ONS server initiated
07/01/11 13:15:53 [4] Logging disabled
adopmnctl.txt
10/08/10-23:30:43 :: adopmnctl.sh version 120.4.12000000.3
10/08/10-23:30:43 :: adopmnctl.sh: Stopping Oracle Process Manager (OPMN) and t
he managed processes
opmnctl: stopping opmn and all managed processes...
10/09/10-11:13:41 :: adopmnctl.sh version 120.4.12000000.3
10/09/10-11:13:41 :: adopmnctl.sh: Starting Oracle Process Manager (OPMN)
opmnctl: opmn start failed.
10/09/10-11:15:09 :: adopmnctl.sh: exiting with status 2
adformsctl.txt
opmnctl: stopping opmn managed processes...
10/09/10-11:18:11 :: adformsctl.sh version 120.12.12000000.5
10/09/10-11:18:11 :: adformsctl.sh: starting OPMN if it is not running
Communication error with the OPMN server local port.
Check the OPMN log files
Communication error with the OPMN server local port.
Check the OPMN log files
Communication error with the OPMN server local port.
Check the OPMN log files
Communication error with the OPMN server local port.
Check the OPMN log files
Communication error with the OPMN server local port.
Check the OPMN log files
Communication error with the OPMN server local port.
Check the OPMN log files
Communication error with the OPMN server local port.
Check the OPMN log files
Communication error with the OPMN server local port.
Check the OPMN log files
Communication error with the OPMN server local port.
Check the OPMN log files
Communication error with the OPMN server local port.
Check the OPMN log files
Communication error with the OPMN server local port.
Check the OPMN log files
Communication error with the OPMN server local port.
Check the OPMN log files
opmnctl: opmn start failed.
Please help."A point to add"
I just noticed that following message is being continously receiving in the database alert_log:
Sat Oct 9 16:04:52 2010
WARNING: inbound connection timed out (ORA-3136)
Sat Oct 9 16:05:32 2010
WARNING: inbound connection timed out (ORA-3136)
Sat Oct 9 16:06:30 2010
WARNING: inbound connection timed out (ORA-3136)
Sat Oct 9 16:07:10 2010
WARNING: inbound connection timed out (ORA-3136)
Sat Oct 9 16:09:35 2010
Incremental checkpoint up to RBA [0x1d.1f9928.0], current log tail at RBA [0x1d.1f9a79.0]
Sat Oct 9 16:11:52 2010
WARNING: inbound connection timed out (ORA-3136)
Sat Oct 9 16:29:40 2010
Incremental checkpoint up to RBA [0x1d.1f9b87.0], current log tail at RBA [0x1d.1f9bf4.0]
~
Please help. -
My problem is that I am working on a page and then I receive ....Error saving the journal. Perhaps your session has expired-try reloading the page". I used to receive from Firefox when reloading page...To display this page, Firefox must send information that will repeat any action'. Now I don't receive this message and I lose info that was entered. How do I get this to pop up again so I can save my messages.
Using Firefox 22.0 u to dateThis can be caused by corrupted cookies or cookies that are blocked (check the permissions on the about:permissions page).
Clear the cache and the cookies from websites that cause problems.
"Clear the Cache":
*Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"
"Remove Cookies" from sites causing problems:
*Firefox/Tools > Options > Privacy > Cookies: "Show Cookies"
You get an alert about resending POST data if you go back to a page or refresh a page that was previously requested from the server by submitting form data via a (hidden) POST form.<br />
Firefox can only make sure to get the same page by resending that POST form.<br />
Firefox doesn't know what that form data means, so Firefox asks for confirmation before resending that form data as such an action can cause you to repeat an action and buy another item or post a message another time.<br />
A way to prevent this pop-up about resending POST data is not to use the Back button, but to open links on a page requested from a server by sending a form with POST date in a new tab (window) with a middle-click or a Ctrl + left-click. -
Communication error with the LOCAL_EXEC Function BAPI_PTMGREXTATTABS_CHECK
Hello,
We use timesheet (CATS) in a separate SAP system from the SAP system in which HR resides.
I found out how the loosely coupled scenario with CATS works with a SAP HR system. We transfer the workschedule and absence data with report RPTIMEOVERVIEW_REPLICATE to the SAP system in which CATS is used. This data is then available in the PTIMEOV1 table to perform time checks in CATS. The distribution model for ALE takes care of the fact that the data is posted into table PTIMEOV1. With BD97 I set up that the BAPI: PTMGREXTATTABS.CHECK has RFCdestination for synchronous calls = LOCAL_EXEC.
When I want to record on an attendance code without clock times then the above works fine. The SAP system in which CATS resides looks into table PTIMEOV1. So far so good.
However, when I want to record hours WITH clock times then I cannot save the data. The error message HRTIM00CATS667 shows up:
"Communication error with the LOCAL_EXEC Function BAPI_PTMGREXTATTABS_CHECK is no t available system"
Diagnosis
An error has occured during communication with the HR System. The HR data in the time sheet cannot be validated.
From the error message description it seems that it wants to check the SAP HR system instead of looking for the check in the SAP system in which CATS resides.....
When I change the value from LOCAL_EXEC to the system in which HR resides then the error disappears, but then it really checks into the SAP HR system (synchronous check with that SAP HR system) and that is not what the customer wants. The check should be local on the PTIMEOV1 table (in case the SAP HR system is down).
I did not find any OSS notes on the topic....or other info on SDN.
Can anyone help me out concerning this starnge error message, at least for me?
Thanks very much in advance,
Kind regards,
Mirko"A point to add"
I just noticed that following message is being continously receiving in the database alert_log:
Sat Oct 9 16:04:52 2010
WARNING: inbound connection timed out (ORA-3136)
Sat Oct 9 16:05:32 2010
WARNING: inbound connection timed out (ORA-3136)
Sat Oct 9 16:06:30 2010
WARNING: inbound connection timed out (ORA-3136)
Sat Oct 9 16:07:10 2010
WARNING: inbound connection timed out (ORA-3136)
Sat Oct 9 16:09:35 2010
Incremental checkpoint up to RBA [0x1d.1f9928.0], current log tail at RBA [0x1d.1f9a79.0]
Sat Oct 9 16:11:52 2010
WARNING: inbound connection timed out (ORA-3136)
Sat Oct 9 16:29:40 2010
Incremental checkpoint up to RBA [0x1d.1f9b87.0], current log tail at RBA [0x1d.1f9bf4.0]
~
Please help. -
I am using form based Sharepoint servers and received below error. Is there any way to solve this?
Sharepoint 2010 in Windows 2008 R2 Server.
A process serving application pool 'Sharepoint-2' suffered a fatal communication error with the Windows Process Activation Service. The process id was '11516'. The data field contains the error number.I don't see any number provided in the event log. I got this through Sharepoint diagnostic tool. below is the log.
Log Name: System
Source: Microsoft-Windows-WAS
Date: 12/17/2013 5:16:34 AM
Event ID: 5011
Task Category: None
Level: Warning
Keywords: Classic
User: N/A
Computer: 525531-WEB03.dfw.intensive.int
Description:
A process serving application pool 'Sharepoint-2' suffered a fatal communication error with the Windows Process Activation Service. The process id was '8180'. The data field contains the error number.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-WAS" Guid="{524B5D04-133C-4A62-8362-64E8EDB9CE40}" EventSourceName="WAS" />
<EventID Qualifiers="32768">5011</EventID>
<Version>0</Version>
<Level>3</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2013-12-17T10:16:34.000000000Z" />
<EventRecordID>23515</EventRecordID>
<Correlation />
<Execution ProcessID="0" ThreadID="0" />
<Channel>System</Channel>
<Computer>525531-WEB03.dfw.intensive.int</Computer>
<Security />
</System>
<EventData>
<Data Name="AppPoolID">Sharepoint-2</Data>
<Data Name="ProcessID">8180</Data>
<Binary>6D000780</Binary>
</EventData>
</Event> -
My mackbook pro 13' A1278, has had multiple errors with the hard disk.
My mackbook pro 13' A1278, has had multiple errors with the hard disk. Now does not recognize the internal hard disk, but connect this HD using usb conector works fine.
So it's a hardware problem.
I'm really disappointePipfromvic,
have you tried installing Mavericks onto an external disk, and booting from the external disk using Startup Manager? If it runs well from an external disk, but continually crashes when running from the internal disk even after clean reïnstallations, then that could point to a faulty internal SATA cable as the culprit. -
when I open Firefox I have to try several times because a Runtime Error with the program C:\Windows\System32\regsvr32.exe
'''Try the Firefox Safe Mode''' to see how it works there. The Safe Mode is a troubleshooting mode, which disables most add-ons.''
''(If you're not using it, switch to the Default theme.)''
* You can open the Firefox 4.0+ Safe Mode by holding the '''Shift''' key when you use the Firefox desktop or Start menu shortcut.
* Or use the Help menu item and click on the '''Restart with Add-ons Disabled...''' menu item while Firefox is running.
''Don't select anything right now, just use "Continue in Safe Mode."''
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before using the Firefox shortcut (without the Shift key) to open it again.''
'''''If it is good in the Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one.
Please follow the [[Troubleshooting extensions and themes]] article for that.
''When you figure out what's causing your issues, please let us know. It might help other users who have the same problem.'' -
There is something wrong with my new macbook pro MD322(Lion 10.7.2). It continually lost connection with the magic mouse. I ensure that the mouse is charged well. I also looked up the matter on Web. It looks that the matter is familiar for many users.
I have a m-audio fast track pro that I'm having a similar problem when using it with my new Macbook Air. I found changing it to 16 bit will work.
I have a Apogee iMic that works fine so my guess is we will have to wait for Avid/M-Audio to update drivers. -
Invalid data status error during the data extraction
Hi,
while extracting capacity data from the SNP Capacity view to BW. i get the "invalid data status error" and the data extraction fails.
when debugged the bad requests of the ODS object, i found that for a certain product(which has both positive and negative input and out qtys) co-product manufacturing orders were created. but this product was not marked as the co-product and functionally its fine.
how can i rectify the data extraction problem..can you advice.
Thanks,
DhanushSir,
In my company for some production order status some are having "errors in cost calculation" ie "cser" .how to deal these kind of errors. -
I am getting follwoing error with the Assosiations. Please anybody let me know how to solve.
Error: oracle.apps.ar.hz.components.contact.server.HzPuiContactCRoleAS: The association end(s) do not specify an attribute.See http://forums.adobe.com/thread/771689?tstart=0
-
Error with the Package Request while uploading epub package onto ACS4.
Hi,
Error with the Package Request while uploading epub package onto ACS4.
There was an error with the Package Request::<error xmlns="http://ns.adobe.com/adept" data="E_PACK_DATABASE http://localhost/packaging/Package Incorrect%20string%20value:%20'\x92Apran...'%20for%20column%20'creato r'%20at%20row%201"/>
Cheers
VikasSee http://forums.adobe.com/thread/771689?tstart=0
Maybe you are looking for
-
"Cannot send email from this device"?
I recently purchased the Easy Release App from the ITunes store and when I try to email the release to my email address it says "Cannot send email from this device". Is it the app that is preventing the sending or is it something to do with the iPod?
-
How to add new attributes to HardgoodShippingGroup
Hi, I added new fields to the user's home address using this item-descriptor: <item-descriptor name="contactInfo" >in the userProfile.xml file. This fields were automatically added to ACC and they can be invoked in the code by using RegistrationFormH
-
Hello, I'm updating code written in Labview 2006 to make it compatible with Labview 2013. My code calls a custom TDMS file viewer vi. This viewer calls a function called "panelresize.vi". This is a NI vi that has been updated since the 2006 versio
-
IPlanet 4.1 seems to be cutting my pages when working with JRun.
I'm using iPlanet Web Server 4.1 with SP 9. It interacts with JRun running as an application server, and it seems not to be serving complete pages, but cutting them in a randomly manner. Can anybody help me? I'm working with HP-UX
-
I have just purchased Photoshop Touch through Google Play store. When I try to run it I get an error message saying license check failed and to sign in to Google play but if the problem persists to contact Adobe. Any ideas what the problem is?