Recently moved and installed ATT DLS - I use their wireless router and connectted my airport express - Now I'm getting the Blue ? on some images
Recently moved and installed ATT DLS - I use their wireless router and connectted my airport express - Now I'm getting the Blue ? on some images - and at times - videos don't load. I've increased / deleted Cache. Suggestions? Misconfig? Could it be possible my configuration from MacBook to router isn't correct?
Thanks!
JG,
Thanks for the info.
Couple of questions. I found an apple support document on this topic that opened with this line:
"AirPort Express and all AirPort Extreme base stations can use WDS. Earlier AirPort base stations can't."
If the TC is an airport extreme base station, why can't this work to extend the network? I think I misunderstand. Here is the full article:
http://support.apple.com/kb/HT2044?viewlocale=en_US
If I buy a new airport extreme, set it to wireless-n only as my main router, am I correct that my existing time capsule could be used as a bridge if plugged in upstairs?
Final question (and that should do it), could I take this old airport express, plug it in upstairs using the ethernet connection, and just create a separate wireless network to use with a different name?
I'd like to keep one network if possible but just kicking around short term solutions.
Thanks again.
Similar Messages
-
My hard drive died last week, and I needed to install a new one. Previously, I was able to save a .doc with text and inserted photo to .pdf and then to .jpg. Now I can get the .pdf but can't determine what to do to convert to .jpg. Does anyone know ?
Rather than do that, which means starting over from scratch, losing all your edits, organisation and so on, why not simply use iPhoto Library Manager to revert the Library to the older version? Easier, less destructive.
The instructions on that are here
If you really want to start over: you can access the Originals folder simply by going to your Pictures Folder and finding the iPhoto Library there. Right (or Control-) Click on the icon and select 'Show Package Contents'. A finder window will open with the Library exposed. -
Do I connect my airport express to my modem via the WAN port and then connect from airport express to my imac with ethernet cable? Is that how you "hard wire" the connection? Because when I do that, I still can't get online. Thanks.
What is the make & model of your modem?
You pretty much stated the correct wiring. There should be an Ethernet cable connected between the modem and the WAN (circle of dots) port on the AirPort Express base station.
Anytime you change networking hardware it is always a good idea to perform a complete power recycle of that hardware. Check out the following AirPort User Tip for details. Please post back your results. -
We recently moved and changed our email but I can't change my iCloud email. Help!
That is because the app you are attempting to update is not owned by your Apple ID. You will have to delete the app and re-purchase it with your own ID, or continue to use your cousin's password to update it.
Cheers,
GB -
I have a new Airport Extreme and and old airport express. I am getting an amber status light on the Extreme and a green light on the Express. The Extreme is blinking amber all the time.
I have internet and everything seems to be working.
I have reset and pulled the power cord on both the extreme and the internet block
How do I make it Green?If things seem to be working OK, but the amber light is flashing......the AirPort Extreme has a message for you. To see what that might be......
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Extreme icon
Click on the amber dot in the small window
It might be a message that a firmware update is available for your AirPort Extreme. -
I am not able to connect Airport Express Base Station Model A1264 with Windows 7 (x64). I did a factory reset, uninstalled and reinstalled the AirPort Utility for Windows v. 5.6.1.
My objective is to extend a non-Apple WiFi network with Airport Express Base Station Model A1264 and use it for direct ethernet and/ or wireless connection. Any guidance as to how I can get set up here?This is very common, we run a mix of mac and various pc brand desktops and laptops, what I have found is that using the windows wireless client rather than manufacturers on some laptops helps, getting the latest wireless drivers from the manufacturer has helped, make sure all your windows updates XP and Vista are current.
If all the above is covered try the different WEP WPA WPA2 variants or even without for test purposes. I have most success with WPA2.
Finally I am assuming your running the latest firmware on the express unit, whilst this hasn't attributed to better connectivity for us I did it regardless.
Message was edited by: Fence Rider -
When I click on Safari, I get the message "Safari quit unexpectedly." I know I have access to my wireless net work because I just found and downloaded updates and can send and receive mail. What is my problem and hoe is it solved?
As Outlook is not an Apple product, you will find more helpers familiar with Outlook here:
Office for Mac forums -
The Ipad Mini has worked on Wifi, and now will not connect. I just have th circle going around apparently because it is searching. Then it says "not connected".
Hi, sven-axel.
You may find this article helpful in troubleshooting issues connecting to a Wi-Fi network.
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
Cheers,
Jason H. -
See above description
Welcome to the Apple Community.
You might try a forced shutdown to begin with, hold down the top and home buttons together until the device shuts down, then restart it. -
My wireless network looses connection between airport express and modem.
The indicator under the "Internet" icon in airport utility switches from green to amber every minute or so. When it is amber I have no, or very slow speed.
Interestingly the Linksys WRT-54G is one of the few non-Apple routers that are WDS-compatible with the earlier 802.11g AirPorts. There are a number of posts on the Internet (use the following search terms: Linksys AirPort WDS) where the authors described how they configured theirs to work.
If; however, you don't want to "experiment," your suggestion to interconnect the two routers by Ethernet should work just fine. In this case, you would want to configure them both for a roaming network. -
I have an iPhone 4 and downloaded all my iTunes music to it. Now when I connect it to my laptop I automatically get the "blue screen of death", does anyone have any insight into this problem?
This will happen if you have photos in your camera roll and an out-of-date scanner or webcam driver. See this: http://support.apple.com/kb/TS1502
-
Why must I continually disconnect and reconnect my airport express in order to get it to play my ITunes library on my TV?
I have a HP Pavillion dv6000 running Windows Vista. Itunes is up to date. I have power cycled the router several times it is a Surfboard sbg6580. still no luck with seeing the airplay symbol on itunes, but Isee it on my phone and can stream music via the airport with my phone. I can see both airports on the airport utility on my laptop. I'm stumped...
-
I recently moved and I got a new sim but I still use my old sim. I want to use both numbers for iMessage and FaceTime but i have absolutely no idea how to do it! please help me! I have a macbook pro and iphone 5
lewbobber wrote:
Basically i need to either take it to a shop that can unlock i.e. £40.00
Be aware, you go that route & every time you try to update or restore, it will error out, leaving your phone unusable. Not to mention, you void all warranty/support.
Sell it & use the proceeds towards an officially unlocked iPhone bought directly from Apple.
Good luck. -
I recently moved and had to disconnect my WD My Pro Edition II 2TB external drive I had been using for backup.
Its been several months (many upgrades to the iMac software during this time), and now when I try to reconnect the external dire (Use a firewire cable) it does not recognize the drive is there. I also tried "reloading" software from the Western Digital site, but after following all the instructions, it looks like my iMac doesn't support this software (I can't even locate it after I follow all the instructions.
Thnaks, for anyones ideas on how I can get this working again.....First of all, you do not really want to use their software; if you want a bootable clone, use either Carbon Copy Cloner or SuperDuper. If you simply want to drag and drop some files, you don't need software to do that. The important thing on any external drive is that you format/partition it correctly (Mac OS Extended (Journaled) and using GUID partition scheme).
Unfortunately, I don't know anything about WD drives or their software, so I don't have any idea what kind of backup you did. Having said that, it should still recognize the external even if it's outdated. Have you tried mounting it manually in Disk Utility? If you can get it to mount, you could (worst case scenario) just drag your stuff off onto your internal and then reformat the external. -
I purchased my MacBook Pro 2 years ago in Okinawa. I recently moved to St Louis. When using the "find my Mac" App, it still says my Mac is in Okinawa. How do I get it to accurately show my Mac is now in St Louis?
Open System Preferences using the menu item " > System Preferences" then select the "Security & Privacy" pane. selec the "Location Services" on the left and enable using the checkbox:
Just noticed you details show you are running OS X 10.7.5 so I am not sure this is exactly correct.
Maybe you are looking for
-
How to change default application associated with some mime types?
When we install some new program, for example GIMP, I assume the newly installed program is added to some mime type database, and the /usr/share/applications/mimeinfo.cache file is automatically generated. Using my example, GIMP will be the default a
-
How can I set a DEFAULT zoom size at ctrl+++ that will hold while changing sites--even in Private Browsing? I'm just starting using Firefox but I won't be using it for long if I have to re-size the screen with every new location viewed.
-
Web Logic server 10.3.5 not running
I am starting the WLS from START-->All Programs-->Oracle Classic Instance - asinst_1-->Start Web Logic Admin Server. When it starts it is giving error highlighted in bold.After Logging in the error in bold keeps coming.I am unable to understand this
-
i imported a large file of photos from my computer to my iphone by accident. how can i remove them all??
-
No sound in playback since moving to 10.5
I have tried playing back movies created in iMovie 6 HD under 10.3. They had sound then. I now have no sound when I play the movies. The audio lines are checked. itunes works fine. It seems that I'm missing some minor detail. Thanks Ken