Reciever volume low

my reciever volume has been to low to use up to my ear for the past three months or so. speaker phone just isnt cutting it anymmore either. any ideas, its barely above a whisper.

Hey Lowss97,
Welcome to Apple Support Communities! Trying out the following troubleshooting steps might be worth a shot:
Resolution
Verify that there is nothing plugged in to the headset jack, including headsets, headphones, or adapters.
Make sure the Ring/Silent switch is not switched to silent.
While on the Home screen, adjust the volume buttons. If you see the icon below, indicating that headphones are attached, there may be debris or an object lodged in the headset jack:
Check the headset jack. If there is an object lodged in the headset jack that is not easily removed, have the iPhone serviced to remove object.
For Original iPhone: If there is light debris, such as lint, in the headset jack, try connecting a pair of headphones to the headset jack and then remove the headphones. Repeat this several times to remove the debris.
If you have installed a protective film on the display, either ensure that the receiver is not covered or remove the film completely.
Check the receiver mesh (which is on the top front of the device, above the display). If it appears blocked, use a clean, small, dry, soft-bristled brush to carefully and gently brush away any debris.
If you have paired with a Bluetooth headset that is nearby, either use the headset or turn Bluetooth off (chooseSettings > General > Bluetooth).
Restart the iPhone.
If restarting the iPhone doesn't resolve the issue, try restoring the device.
If the issue persists, go to the Service Answer Center - iPhone for information on service.
via:
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/TS1630
Best,
David

Similar Messages

Audio volume low when computer wakes from sleep - os x yosemite

I've been having an issue ever since I upgraded to OS X Yosemite, where the audio volume coming out of my external speakers is extremely low after I wake my computer up from sleep. The only resolution I have found is restarting the computer. Once I do that, the audio volume is great. If I were to boot up my computer after it has been completely shut down, the audio volume is also great. The issue only occurs after sleep. Anyone else having a similar issue? Is there another fix besides restarting the computer?
Speakers: Bose Companion 2 Series II (these are wired, not bluetooth)
Computer: Mac Pro - late 2013 - running Yosemite

This is a BUG. It has been submitted to engineering many times - unfortunately Apple has not done anything about it.   We have 5 Mac Pros, all 5 do the same thing after updating to Yosemite.   The PRAM / SMC reset is useless - we even installed a fresh OS on one of the machines (a suggestion of the level 2 Apple tech) same problem.   Clearly this is a system level bug.   Only way to get it resolved is to keep pounding the bug report site with requests.     The squeaky wheel gets the oil.   The problem is 100% repeatable on the machines that exhibit the bug.
In the mean time set up an applescript with this command and it will reset the sound - do not include the brackets :
<do shell script "sudo killall coreaudiod" with administrator privileges>
Run it every time you wake from sleep and you won't have to deal with the problem ever again.
Pretty lame that Apple has not fixed it even though the problem appears to be pretty widespread.

Ring volume low & people cant hear me very well even on speaker???

Howdy, I have a iphone 4 version 4.3.5 (not sure how to find operating system..) I am having problems with the volume. The incoming call ring is really low, I have increased it to max in the settings with no luck and people are finding it hard to hear me? I just hooked it up to itunes to sync. I am not sure if there is a problem with the speakers at the bottom - how do I take the back or bottom off - maybe it needs a clean out. or Is there a download update?
I am not very iphone savy so any assistance wld be appreciated.
Cheers

The fact that it works with Facetime means your microphone works.
You can try resetting your iPhone by simultaneously pressing and holding the Home and Sleep/Wake buttons until you see the Apple Logo. This can take up to 15 seconds so be patient and don't release the buttons until the logo appears.
Try again to see if the problem persists.

Sound recorder playback volume low ?

I have a dv6000 notebook , for the first time ever I tried recording sound using windows movie maker to add ''narration'' but the playback volume is very low .
I tried the windows '' sound recorder '' and got the same result .
I've been through all the standard adjustments and settings and have gone into ' control panel ' and adjusted 'levels' and everything else with no success .
When I record a video using the sound on my camera the volume is fine - it's just the mic sound that is low whether I use an external mic or the built in ones .

I have the same issue and I see no responses to your inquiry.. This Windows help menu leaves much to be desired. Im sure I will one day figure out how to work this version that I had no clue I was buying bc it should come with a warning label.. its completely different and agonizing and great help menu lovely.. Im sorry to be so negative wish I could help.. Ill sit here all night till I figure it out and then post an option on how to adjust the recording volume.. Unreal..

Volume lower on it's own__iPod Classic 80gb 5.5 generation

Hi
I have this classic ipod for a long-time. Currently, I am using it in the car with 3.5mm radio cable. Becasue of connecting to the auto speakers, I have to set ipod volume to the maximum in order to have enough volume from the speaker. The weird thing is the iPod always decrease volume on its own to some lower level and every time is different. Sometime is back to the middle of volume and sometime even lower. I change a better 3.5mm ($20) but it still happens. I also updated the firm to the latest. But it's still..
There is only way I know that can treat this problem is lock the screen. But that is not the right way for me since I always change to the next song.
Did someone have the same problem like me?

You have the mid-2010 problem. There's an issue with the graphics module on that machine. There was a program in place to replace the motherboard within 3 years of purchase, but you're probably outside of that. Some folks have supposedly gotten theirs changed outside of that period, so you can try.
http://support.apple.com/kb/TS4088?viewlocale=en_US&locale=en_US
What you can do to use it is download gfxstatus from http:gfx.io and force the graphics to Intel. That will lessen the panics at the expense of graphics speed.
You may be eligible for a depot repair, which is a flat rate of about $310. Ask at the Genius Bar. Take along a printout of your panic.

Why is the volume low?

I am importing my CD collection and I noticed that when I play any of my songs back that they are really low. I can hardly hear them without turning up the volume all the way on both the speakers and my MacBook Pro. When I higher the volume, the sound is clear, no water damage or anything. Also, my speakers work fine for YouTube, system sounds, etc. it's only my iTunes library that has a low volume.
Please help!

After checking the volumne selection:
Try restarting your computer.

Nokia 3600 Slide ringing volume low

Whenever i choose the ringing tone from my list with mp3's and i get the 'preview' of the song, the volume is great, is loud so i can hear it (the phone has a speaker on the back). And also i can hear the mp3 loud when i play it with my media player.
But when someone calls me, the volume is lower than what i heart during the preview (the ringing tone is set to max), it also starts sort of ascending even if the ascending tone option is not activated. (it starts by using his regular (don't know where it is) speaker, then moves on that big speaker from the back that i was telling about).
I realise that this might be just the way the phone works but i thought maybe i can somehow make the ringing tone as loud as when i play files with my media player.
I honestly can't hear the phone when i'm in a louder area or when i'm sleeping. Any ideas?
Solved!
Go to Solution.

Most recent Nokia phones will automatically be in "ascending mode" if you choose the very highest volume (meaning that the ring will begin quiet and increase to maximum).
If you are not hearing your tone well enough choose the second highest volume setting so that it starts at the set volume instead of working up to it? Also, the choice of tone is also important - if you are often in noisy places or carry your phone in a pocket or bag, then you may need to ignore personal favourites like the tune you first danced to wit your partner and just go for something noticably loud from the first note.

CSV Volume low on disk space warning alltough the space isn't used (VSS?)

HI Guys,
we are running a HV-2012 Cluster. most of the VM's are backuped by DPM 2012 r2.
Recently i noticed some "CSV low disk Space Warning" withing SCOM.
Today i looked at one of the CSV's.
The Size is 1800GB and if you look at the Size of all the Folders on the Volume within the Explorer they are 1250 GB.
After that i looked a the Failover Cluster Manager -> Storage -> Disk: This console states that there are only 36GB Free on the Volume.
My guess is that the VSS Snapshots use up the Disk-Space? But if i do a vssadmin list shadowstorage
only drive c is displayed.
Could this end up in a Problem or is the vss Space freed automaticly?
Or is there something else wrong?
Anyone a clue on this?
regards
Stefan

First thing is that you're running out of space and need to move quickly to make space while you figure this out. When you run out of space, the VMs will shut down.
How many VMs you have on that CSV and many VHD(x) disks you have an the CSV? Another question that matters here is how fast is your backup for each VM?
Regardless of the backup software being DPM or any other VSS based backup, it works by creating a checkpoint of the VM, which creates a snapshot of its disks. A volume snapshot turns the VM disk into a read only disk and starts a change log disk (.avhdx)
file. The crash consistent read-only .vhdx file is then copied by the backup software agent from the host to the backup server. Upon successful completion, the agent deletes the VM checkpoint, which merges the disk snapshot, merging the .avhdx and .vhdx files
back into one file.
So, if you're backup time for this VM takes hours, during that time, the VM disk space usage can grow a lot more that what it would usually use. If you run out of disk space then, backup will fail, the VM will be suspended, and you cannot bring it online,
since the merge needs even more disk space.
Sam Boutros, Senior Consultant, Software Logic, KOP, PA http://superwidgets.wordpress.com (Please take a moment to Vote as Helpful and/or Mark as Answer, where applicable) _________________________________________________________________________________
Powershell: Learn it before it's an emergency http://technet.microsoft.com/en-us/scriptcenter/powershell.aspx http://technet.microsoft.com/en-us/scriptcenter/dd793612.aspx

Hp 15 r014tx, Left speaker volume low?

Hi I have HP 15 R014TX and when I plays music I feels like left speaker volume is low than the right one. It is same when playing games, playing videos too. Is the speaker is complaint or is it because of the DTS audio ?

Hey,
If you've completed the document, then I'd recommend testing hardware. The only thing software wise left would be a Refresh. As it works from another source correctly, I have a feeling its hardware.
You can use this to test the Audio: Testing for Hardware Failures (Windows 8). This may not provide accurate results as you do have sound from both, just not balanced.
I would also suggest calling into phone support, they may have other ideas for you.
Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I worked on behalf of HP.

Volume low on your TV can't figure out why.. I FOUND THE ANSWER

Hello,
I figured I will share this information with everyone save you all the waste of time I went through .
So my sound is low on the TV but I am using my TV remote and the Fios remote and I can't raise the volume. But when I turn the TV off and on . I can see for a second the volume on low on the top right corner. I tried everything to raise the volume. So I called the hotline and Google this issue lots of dead ends.. I got an AWESOME person on the TV support for Verizon FIOS here is the fix
Go to your FIOS remote
Hit Menu
Hit Settings
Hit Audio
Then go to Volume Control make sure its says Variable not fixed ( fixed is if you want to make sure your kids can never blast Dora past a certain volume )
Then click ok go to the Set-top Box Volume
Then to raise the volume use the UP and DOWN keys near the OK key. That's right the vol + or - doesn't work yet.
I would do this raise it to the max then ok out till you are out of the menus.
Then try the volume on the remote the + / - will work.

They are usually intended for mobile devices like iPhones, iPad's (and Kindle's) ... you need the Apple iBook app to read them.
Google for Stanza or eReader and it should do what you want.

IOS 8 iPhone 6 Plus Keyboard Click Volume Low

The Keyboard click sounds are too low to be heard when typing into any text entry field.
Volume is up all the way.
This is the only sound effect that is not working, all other sounds work just fine.
Have restarted several times, no change.
Have had the iPhone 6 Plus for about a month and this just started happening a couple of days ago, very annoying.
Any help greatly appreciated!
Bern

Hi Japib thanks for the reply.
I have both volumes all the way up, seems to be an intermittent thing...
Seems the volume for keyboard clicks 'turns off' on its own randomly, very odd, maybe a defective phone?

Phone 3905 Volume Low

Ter uma empresa com vários telefones 3905, e vários têm baixa problema de volume, ou problema atual de mudas em links.
A questão do baixo volume de chamadas, os telefones estão com o volume no máximo.
Qualquer solução para as duas situações?

Olá Alexandre,
Da uma olhada neste link. Também temos um Cliente na mesma condição
https://supportforums.cisco.com/discussion/11760811/3905-volume-very-low
Att,
Wilson

Audio track volume low?

I Bus recorded my midi EXS drum track by routing it to Bus1 and by choosing Bus1 as an Input on the Audio track.
Problem now is that the Audio track is not loud enough. I normalized it using the Functions menu in the sample editor window. But when I play the audio region in the arrange window there is absolutely no volume increase?
Please help.

It's an old school assumption to always think the maximum level will lead to better results. With 24-Bit we have a lot of headroom and the resolution of Audio even at lower levels is appropriate.
Normalizing will alter the waveforms, add the empty bits at the top to the bottom of the file thus raising the level as well as the noise floor.
http://gearslutz.com/board/so-much-gear-so-little-time/21302-does-trk-normalizin g-lose-headroom-mix.html
Mastering Audio by Bob Katz is a good book for these kind of topics...
I actually just made a test with some sine waves, the normalized sine wave had 0,3% of DC offset added whereas the original file had 0% DC offset.
Also in RX the spectrums of the two files look a little different:
2 khz sinewave at -12 dB
2 khz sinewave normalized

Audio volume low

Could domeone help me with audio recorded in QT directly from the video camera? The audio volume of the .mov file is very low although it's turned to maximum. When the same clip is uploaded from camera to Final Cut Pro the volume of audio is normal. When this clip is exported from FCP to QT the audio of the .mov is loud and clear.
Milan

This is a BUG. It has been submitted to engineering many times - unfortunately Apple has not done anything about it.   We have 5 Mac Pros, all 5 do the same thing after updating to Yosemite.   The PRAM / SMC reset is useless - we even installed a fresh OS on one of the machines (a suggestion of the level 2 Apple tech) same problem.   Clearly this is a system level bug.   Only way to get it resolved is to keep pounding the bug report site with requests.     The squeaky wheel gets the oil.   The problem is 100% repeatable on the machines that exhibit the bug.
In the mean time set up an applescript with this command and it will reset the sound - do not include the brackets :
<do shell script "sudo killall coreaudiod" with administrator privileges>
Run it every time you wake from sleep and you won't have to deal with the problem ever again.
Pretty lame that Apple has not fixed it even though the problem appears to be pretty widespread.

Why is my volume low only in receiver?

My new 4s is incredible only except for the volume being ridiculously low in the receiver. Speaker and ring tone volumes are great and crystal clear but I can't hardly hear anything from the receiver.

I agree I have put the volume up and everything and it still seems really low.

Reciever volume low

Similar Messages

Maybe you are looking for